USER MANUAL - AV-iQ
Contents
1. Table 4 includes the technical specifications Table 4 Technical Specifications of the WP 210A XGA Audio Line Driver INPUTS VIDEO Looping analog red green AUDIO Unbalanced stereo 3 5mm blue signals 0 7 Vpp 75 Q H and V mini jack sync TTL level on HD15F connectors OUTPUTS VIDEO 1 RGBHV on 5 BNC AUDIO Balanced stereo terminal connectors block connector MAX OUTPUT LEVEL VIDEO 2Vpp AUDIO 5 3Vpp RESOLUTION Exceeding UXGA DIFF GAIN 0 05 DIFF PHASE 0 02 Deg K FACTOR lt 0 05 S N RATIO VIDEO 74 2dB CONTROLS Cable EQ control OdB to 8dB 50 MHz Level control 1 3dB to 6dB ID BIT button TERM button Hs Horizontal and Vs Vertical Sync switches right and left audio level controls COUPLING VIDEO AC AUDIO AC AUDIO BANDWIDTH gt 100kHz AUDIO THD NOISE lt 0 032 AUDIO 2nd HARMONIC lt 0 005 POWER SOURCE 12 VDC 95mA DIMENSIONS 6 9cm x 5 0cm x 11 4cm 2 72 x 1 97 x 4 49 W D H WEIGHT 0 3 kg 0 67 Ibs approx ACCESSORIES Power supply 1 Specifications are subject to change without notice LIMITED WARRANTY Kramer Electronics hereafter Kramer warrants this product free from defects in material and workmanship under the following terms HOW LONG IS THE WARRANTY Labor and parts are warranted for seven years from the date of the first customer purchase WHO IS PROTECTED Only2. could be used for component HDTV by connecting YPbPr in place of GBR and not connecting H and V 6 KRAMER SIMPLE CREATIVE TECHNOLOGY Using the WP 210A XGA Audio Line Driver 5 2 Operating the WP 210A XGA Audio Line Driver To operate your WP 210A XGA Audio Line Driver 1 Connect your XGA source for example a laptop s digital graphics card to the Input HD15F connector and to the AUDIO Input 3 5mm mini jack for example using a Kramer C GMA GMA cable VGA HD15M Audio jack to VGA HD15M Audio jack Alternatively you can connect an XGA source to the Input HD15F connector and a separate audio source to the AUDIO Input Connect the HD15F Loop connector to a local monitor if required Push in the ID Bit button to set to ON Adjust the output signal level and or cable compensation equalization level if required as well as the right and or left audio output signal levels 1 Not supplied The complete list of Kramer cables is on our Web site at http www kramerelectronics com 2 Use a screwdriver to carefully rotate the Potentiometer adjusting the appropriate level 3 Insert a screwdriver into the small hole and carefully rotate it trimming the appropriate audio output level Using the WP 210A XGA Audio Line Driver Bor zi of 5 PS A oF gi Figure 8 Connecting the WP 210A KRAMER SIMPLE CREATIVE TECHNOLOGY Technical Specifications 6 Technical Specifications
3. 07 O 2 QU a Institute of Quality amp Control Kramer Electronics Ltd Web site www kramerelectronics com E mail info kramerel com P N 2900 000210 REV 2
4. Kramer Electronics Ltd ah KRAMER USER MANUAL Model WP 210A XGA Audio Line Driver Contents Contents 1 Introduction 2 Getting Started 3 Overview 4 Your WP 210A XGA Audio Line Driver 4 1 Your WP 210A Front Panel 4 2 Your WP 210A Left Panel 4 3 Your WP 210A Right Panel 5 Using the WP 210A XGA Audio Line Driver 5 1 Installing the WP 210A XGA Audio Line Driver 5 2 Operating the WP 210A XGA Audio Line Driver 6 Technical Specifications Figures Figure 1 WP 210A Front Panel Figure 2 WP 210A Left Panel Figure 3 WP 210A Right Panel Figure 4 Example of Conference Room WP 210A Installation Figure 5 WP 210A RGBHV Outputs Figure 6 Connecting the Balanced Stereo Audio Output to a Balanced Acceptor Figure 7 Connecting the Balanced Stereo Audio Output to an Unbalanced Acceptor Figure 8 Connecting the WP 210A Tables Table 1 WP 210A Front Panel Features Table 2 WP 210A Left Panel Table 3 WP 210A Right Panel Table 4 Technical Specifications of the WP 210A XGA Audio Line Driver auau nn A AUN m pa DANNDDNA HW oR AW Introduction 1 Introduction Welcome to Kramer Electronics since 1981 a world of unique creative and affordable solutions to the infinite range of problems that confront the video audio and presentation professional on a daily basis In recent years we have redesigned and upgraded most of our line making the best even better Our 500 plus different models n
5. MPLE CREATIVE TECHNOLOGY Your WP 210A XGA Audio Line Driver 4 1 Your WP 210A Front Panel Figure 1 and Table 1 define the front panel of the WP 210A G Input XGA __Loop 200 209 Figure 1 WP 210A Front Panel Table 1 WP 210A Front Panel Features Feature Function 1 Input HD15F Connector Connect to the VGA XGA source 2 EQ Potentiometer Adjusts the cable compensation equalization level 3 Level Potentiometer Adjusts the output signal level 4 AUDIO R Level Trimmer Adjusts the right audio output signal level 5 AUDIO L Level Trimmer Adjusts the left audio output signal level 6 AUDIO Input 3 5mm Mini Jack Connects to the unbalanced stereo audio source 7 Holes 2 For fastening the wall plate in place 8 ONLED Illuminates when receiving power 9 ID Bit Button Selects ID BIT when pushed in when outputting a VGA signal from a notebook to an external VGA monitor 10 Term Button Terminates with 75Q when pushed in or release for looping 11 VGA Det LED Illuminates when detecting an XGA signal 12 Loop HD15F Connector For VGA XGA looping to increase output availability 1 Degradation and VGA XGA signal loss can result from using long cables due to stray capacitance sometimes leading to a total loss of sharpness in high resolution signals 2 Use a screwdriver to carefully rotate the P
6. for example in a conference room as the example in Figure 4 illustrates eo Figure 4 Example of Conference Room WP 210A Installation For details of how to e Install your WP 210A XGA Audio Line Driver see section 5 1 e Operate your WP 210A XGA Audio Line Driver see section 5 2 Using the WP 210A XGA Audio Line Driver 5 1 Installing the WP 210A XGA Audio Line Driver To install your WP 210A XGA Audio Line Driver 1 Connect the 5 RGBHV BNC output connectors to the pre installed wiring in the wall box opening that connects to the XGA acceptor for example a projector as Figure 5 defines Each BNC connector is color coded Red R Green G Blue B Yellow Vertical Sync White Horizontal Sync Figure 5 WP 210A RGBHV Outputs 2 Connect the terminal block balanced stereo output as one of the following LLGRR LLGRR ais E G G Figure 6 Connecting the Balanced Stereo Figure 7 Connecting the Balanced Stereo Audio Output to a Balanced Acceptor Audio Output to an Unbalanced Acceptor Set both the Hs and Vs switches 4 Connect your 12V DC power supply to the terminal block connector taking care that polarity is correct 5 Insert the WP 210A directly into the wall box opening and then mount the front panel securely using the screws 1 The WP 210A
7. k with the WP Frame and or the VPM 2 XGA Line Driver wall plate 3 Download up to date Kramer user manuals from the Internet at this URL http www kramerelectronics com 4 The complete list of Kramer cables is on our Web site at http www kramerelectronics com 1 Your WP 210A XGA Audio Line Driver e An amplified and equalized RGBHV output on 5 BNC connectors e An unbalanced stereo audio input on a 3 5mm mini jack e A balanced stereo audio output on a terminal block connector In particular the WP 210A XGA Audio Line Driver has e Level control e Cable equalization control e Left and right audio level controls e Buttons for ID Bit control and loop termination e Switches to select between analog digital sync operation e Resolution exceeding UXGA that ensures transparent operation e A standard 12 Volt DC feed Achieving the best performance means e Connecting only good quality connection cables thus avoiding interference deterioration in signal quality due to poor matching and elevated noise levels often associated with low quality cables e Avoiding interference from neighboring electrical appliances e Positioning your WP 210A away from moisture excessive sunlight and dust 4 Your WP 210A XGA Audio Line Driver This section defines the WP 210A XGA Audio Line Driver e Front panel see section 4 1 e Left panel see section 4 2 e Right panel see section 4 3 1 VGA UXGA output signal 2 KRAMER SI
8. nsibility of the Kramer dealer from whom the product was purchased 3 Shipping charges HOW YOU CAN GET WARRANTY SERVICE 1 To obtain service on you product you must take or ship it prepaid to any authorized Kramer service center Ze Whenever warranty service is required the original dated invoice or a copy must be presented as proof of warranty coverage and should be included in any shipment of the product Please also include in any mailing a contact name company address and a description of the problem s 3 For the name of the nearest Kramer authorized service center consult your authorized dealer LIMITATION OF IMPLIED WARRANTIES All implied warranties including warranties of merchantability and fitness for a particular purpose are limited in duration to the length of this warranty EXCLUSION OF DAMAGES The liability of Kramer for any effective products is limited to the repair or replacement of the product at our option Kramer shall not be liable for 1 Damage to other property caused by defects in this product damages based upon inconvenience loss of use of the product loss of time commercial loss or 2 Any other damages whether incidental consequential or otherwise Some countries may not allow limitations on how long an implied warranty lasts and or do not allow the exclusion or limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you This warranty give
9. otentiometer adjusting the appropriate level 3 Insert a screwdriver into the small hole and carefully rotate it trimming the appropriate audio output level 4 When the ID BIT is ON the notebook will output to an external VGA monitor 5 At any resolution VGA SVGA XGA and so on and HD resolutions 3 Your WP 210A XGA Audio Line Driver 4 2 Your WP 210A Left Panel Figure 2 and Table 2 define the left panel of the WP 210A 9 o MO oipny 1eg Table 2 WP 210A Left Panel Feature Function 1 Bal Audio Out Terminal Block Connector Connects to the balanced stereo audio acceptor Figure 2 WP 210A Left Panel 4 3 Your WP 210A Right Panel Figure 3 and Table 3 define the right panel of the WP 210A Table 3 WP 210A Right Panel tt Feature Function 1 12V GND 12V DC connector for powering the unit 2 H Horizontal Sync Switch Sync Switch 3 V Vertical Set both switches to TTL for a digital sync source for example a graphics card from a PC or laptop Set both switches to Analog if the source is analog based for example an RGBHV source with coaxial cable for sync such as a camera with analog H and V syncs Figure 3 WP 210A Right Panel 4 KRAMER SIMPLE CREATIVE TECHNOLOGY Using the WP 210A XGA Audio Line Driver 5 Using the WP 210A XGA Audio Line Driver You can use your WP 210A XGA Audio Line Driver
10. ow appear in 8 Groups which are clearly defined by function Congratulations on purchasing your WP 210A XGA Audio Line Driver active wall plate which is ideal for graphics and audio installations in board conference and training rooms as well as long distance signal distribution The package includes the following items e WP 210A XGA Audio Line Driver e This user manual 2 Getting Started We recommend that you e Unpack the equipment carefully and save the original box and packaging materials for possible future shipment e Review the contents of this user manual e Use Kramer high performance high resolution cables 3 Overview The Kramer WP 210A XGA Audio Line Driver part of our successful line of Wall Plate Adapters is an enhanced version of our popular WP 210 XGA Line Driver wall plate The WP 210A XGA Audio Line Driver includes e A VGA input up to UXGA resolution on a standard HD 15 connector e Local monitor loop through on an HD15F connector 1 GROUP 1 Distribution Amplifiers GROUP 2 Video and Audio Switchers Matrix Switchers and Controllers GROUP 3 Video Audio VGA XGA Processors GROUP 4 Interfaces and Sync Processors GROUP 5 Twisted Pair Interfaces GROUP 6 Accessories and Rack Adapters GROUP 7 Scan Converters and Scalers and GROUP 8 Cables and Connectors 2 In addition to our active wall plate devices Kramer s WP series consists of passive wall plate and passive connection modules that wor
11. s you specific legal rights and you may also have other rights which vary from place to place NOTE All products returned to Kramer for service must have prior approval This may be obtained from your dealer This equipment has been tested to determine compliance with the requirements of EN 50081 Electromagnetic compatibility EMC generic emission standard Part 1 Residential commercial and light industry EN 50082 Electromagnetic compatibility EMC generic immunity standard Part 1 Residential commercial and light industry environment CFR 47 FCC Rules and Regulations Part 15 Radio frequency devices Subpart B Unintentional radiators CAUTION B Servicing the machines can only be done by an authorized Kramer technician Any user who makes changes or modifications to the unit without the expressed approval of the manufacturer will void user authority to operate the equipment B Use the supplied DC power supply to feed power to the machine B Please use recommended interconnection cables to connect the machine to other components 10 KRAMER SIMPLE CREATIVE TECHNOLOGY For the latest information on our products and a list of Kramer distributors visit our Web site www kramerelectronics com where updates to this user manual may be found We welcome your questions comments and feedback Safety Warning Disconnect the unit from the power supply before opening servicing Caution 90
12. the first purchase customer may enforce this warranty WHAT IS COVERED AND WHAT IS NOT COVERED Except as below this warranty covers all defects in material or workmanship in this product The following are not covered by the warranty 1 Any product which is not distributed by Kramer or which is not purchased from an authorized Kramer dealer If you are uncertain as to whether a dealer is authorized please contact Kramer at one of the agents listed in the web site www kramerelectronics com Ze Any product on which the serial number has been defaced modified or removed 35 Damage deterioration or malfunction resulting from i Accident misuse abuse neglect fire water lightning or other acts of nature ii Product modification or failure to follow instructions supplied with the product iii Repair or attempted repair by anyone not authorized by Kramer iv Any shipment of the product claims must be presented to the carrier v Removal or installation of the product vi Any other cause which does not relate to a product defect vii Cartons equipment enclosures cables or accessories used in conjunction with the product WHAT WE WILL PAY FOR AND WHAT WE WILL NOT PAY FOR We will pay labor and material expenses for covered items We will not pay for the following 1 Removal or installations charges 2 Costs of initial technical adjustments set up including adjustment of user controls or programming These costs are the respo
Download Pdf Manuals
Related Search