GC3600 Series
Contents
1. iron on a stable level and horizontal surface Do not put perfume vinegar starch descaling agents ironing aids or other chemicals in the water tank Thi s appliance is intended for household use only Electromagnetic fields EMF This Philips appliance complies with all standards regarding electromagnetic fields EMF If handled properly and according to the instructions in this user manual the appliance is safe to use based on scientific evidence available today 7 8 ENGLISH General description Fig 1 Spray nozzle Filling opening Cap of filling opening Steam boost button 4 Steam control CALC CLEAN Calc Clean function 0 no steam amp minimum steam amp maximum steam Spray button Red auto off light GC3660 only Temperature dial Temperature light aims cord Flexible rubber handle part Anti Calc tablet Water tank Heel ot shown filling cup Before first use Remove any sticker protective foil or plastic from the soleplate Fig 2 Preparing for use Filling the water tank monu gt ZZXZPATIOQOT Do not put perfume vinegar starch descaling agents ironing aids or other chemicals in the water tank Make sure the appliance is unplugged Set the steam control to position 0 no steam Fig 3 Open the cap of the filling opening ENGLISH 9 Use the filling cup to fill the water tank with tap water up to the maximum level Tilt the iron backwar2. it for the first time This stops after a short while Sensor controlled handle with energy saving technology While you iron the sensor in the handle ensures that the iron produces the optimal amount of steam As 90 of the energy consumption of an iron is used to create steam energy consumption is optimised by optimising the steam output When you intuitively put more force on the handle to remove stubborn creases the iron automatically produces more steam When you do not press the handle when you lift the iron and when the iron is standing on its heel or on its soleplate without any movement the automatic energy saving technology limits the steam output to reduce energy consumption Fig 7 Steam ironing Make sure that there is enough water in the water tank Set the recommended ironing temperature see chapter Preparing for use table Temperature and steam settings Set the appropriate steam setting Make sure that the steam setting is suitable for the set ironing temperature see chapter Preparing for use table Temperature and steam settings Fig 8 Note The iron is ready for steam ironing as soon as it has reached the set ironing temperature Note If the set ironing temperature is too low MIN to e 6 water may drip from the soleplate see chapter Features section Drip stop ENGLISH 11 Ironing without steam Set the steam control to position 0 no steam Fig 3 Set t
3. this happens you may hear a sound Automatic shut off function specific types only The automatic shut off function automatically switches off the iron if it has not been moved for a while D The red auto off light flashes to indicate that the iron has been switched off by the automatic shut off function Fig 13 To let the iron heat up again Pick up the iron or move it slightly D The red auto off light goes out D If the temperature of the soleplate has dropped below the set ironing temperature the temperature light goes on If the temperature light goes on after you have moved the iron wait for it to go out before you start ironing Note If the temperature light does not go on after you move the iron the soleplate still has the right temperature and the iron is ready for use Cleaning and maintenance Cleaning Set the steam control to position 0 remove the mains plug from the wall socket and let the iron cool down Wipe flakes and any other deposits off the soleplate with a damp cloth and a non abrasive liquid cleaning agent ENGLISH 13 To keep the soleplate smooth avoid hard contact with metal objects Never use a scouring pad vinegar or other chemicals to clean the soleplate Clean the upper part of the iron with a damp cloth Regularly rinse the water tank with water Empty the water tank after you have rinsed it Fig 14 Double Active Calc System The Double Active Calc System consists of
4. Register your product and get support at www philips com welcome GC3600 Series PHILIPS Introduction Congratulations on your purchase and welcome to Philips To fully benefit from the support that Philips offers register your product at www philips com welcome This user manual contains information about the surprising features of this iron and some tips to make ironing easier and more enjoyable This iron is equipped with a special sensor controlled handle and automatic energy saving technology While you iron the sensor in the handle ensures that the iron produces the optimal amount of steam As 90 of the energy consumption of an iron is used to create steam energy consumption is optimised by optimising the steam output When you intuitively put more force on the handle to remove stubborn creases the iron automatically produces more steam When you do not press the handle when you lift the iron and when the iron is standing on its heel or on its soleplate without any movement the automatic energy saving technology limits the steam output to reduce energy consumption We hope you enjoy using this iron Important Read this user manual carefully before you use the appliance and save it for future reference Danger ever immerse the iron in water Warning Check if the voltage indicated on the appliance corresponds to the ocal mains voltage before you connect the appliance Do not use the appliance if
5. an Anti Calc tablet inside the water tank combined with the Calc Clean function 1 The Anti Calc tablet prevents scale from clogging the steam vents This tablet is constantly active and does not need to be eplaced Fig 15 2 The Calc Clean function removes the scale particles from the iron 5 Calc Clean function Use the Calc Clean function once every two weeks If the water in your area is very hard i e when flakes come out of the soleplate during ironing use the Calc Clean function more frequently Set the steam control to position 0 and remove the mains plug from the wall socket Fill the water tank to the maximum level Do not pour vinegar or other descaling agents in the water tank Set the temperature dial to MAX Put the mains plug in an earthed wall socket Unplug the iron when the temperature light goes out EA Hold the iron over the sink Push the steam control to the CALC CLEAN position and hold it Gently shake the iron to and fro Fig 16 D Steam and boiling water come out of the soleplate Impurities and flakes if any are flushed out 14 ENGLISH Release the steam control as soon as all the water in the tank has been used up El Repeat the Calc Clean process if the iron still contains a lot of impurities After the Calc Clean process Put the plug back into the wall socket and let the iron heat up to let the soleplate dry Unplug the iron when the temperature light goes out Move th
6. ds to check if the water level has reached the MAX indication Fig 4 Do not fill the water tank beyond the MAX indication Close the cap of the filling opening click Setting the temperature Temperature and steam settings Fabric type Temperature Steam Steam boost setting setting Linen MAX ES Yes Cotton eco ES Yes Wool ee NA o Silk 0 N A Synthetic fabrics eg 0 NA acrylic nylon polyamide polyester Check the laundry care label for the required ironing temperature If you do not know what kind or kinds of fabric an article is made of determine the right ironing temperature by ironing a part that is not visible when you wear or use the article Silk woolen and synthetic materials iron the reverse side of the fabric to prevent shiny patches To prevent stains do not use the spray function Start ironing the articles that require the lowest ironing temperature such as those made of synthetic fibers Put the iron on its heel To set the required ironing temperature turn the temperature dial to the appropriate position Fig 5 See table Temperature and steam settings 10 ENGLISH Put the mains plug in an earthed wall socket Dd The temperature light goes on Fig 6 When the temperature light goes out wait a while before you start ironing Note The temperature light goes on from time to time during ironing Using the appliance Note The iron may give off some smoke when you use
7. e iron gently over a piece of used cloth to remove any water stains that may have formed on the soleplate Let the iron cool down before you store it Set the steam control to position 0 remove the mains plug from the wall socket and let the iron cool down Wind the mains cord round the cord storage facility Fig 17 Note Make sure that the mains cord does not press down the handle during storage Store the iron on its heel in a safe and dry place Environment Do not throw away the appliance with the normal household waste at the end of its life but hand it in at an official collection point for recycling By doing this you help to preserve the environment Fig 18 Guarantee service If you need service or information or if you have a problem please visit the Philips website at www philips com or contact the Philips Consumer Care Centre in your country you find its phone number in the ENGLISH 15 worldwide guarantee leaflet If there is no Consumer Care Centre in your country go to your local Philips dealer Troubleshooting This chapter summarises the most common problems you could encounter with the appliance If you are unable to solve the problem with the information below contact the Consumer Care Centre in your country Problem Possible cause Solution The iron is There is a Check the mains cord the plug plugged in connection and the wall socket but the problem soleplate stays cold T
8. function Press the cap until you hear a click Rinse the water tank and do not put any additive in the water tank Set the temperature dial to a setting between and MAX Problem Water drips from the soleplate after the iron has cooled down or has been stored Flakes and impurities come out of the soleplate during ironing The red auto off light flashes specific types only Possible cause You have set a too low temperature for steam ironing You have put the iron in horizontal position with water still left in the water tank Hard water forms flakes inside the soleplate The automatic shut off function has switched off the iron see chapter Features ENGLISH 17 Solution Set an ironing temperature that is suitable for steam ironing ee to MAX Put the iron on its heel and wait until the temperature light goes out before you start ironing Empty the water tank before you store the iron Store the iron on its heel Use the Calc Clean function one or more times see chapter Cleaning and maintenance section Calc Clean function Move the iron slightly to deactivate the automatic shut off function The red auto off light goes out
9. he recommended ironing temperature see chapter Preparing for use table Temperature and steam settings Spray function You can use the spray function to remove stubborn creases at any temperature Make sure that there is enough water in the water tank Press the spray button several times to moisten the article to be ironed Fig 9 Steam boost A powerful steam boost helps to remove very stubborn creases The steam boost function can only be used at temperature settings between and MAX Press and release the steam boost button Fig 10 Concentrated steam boost from the special Steam Tip GC3640 GC3660 only The concentrated steam boost from the long vents in the Steam Tip enhances the distribution of steam into every part of your garment The concentrated steam boost function can only be used at temperature settings between ee e and MAX Press and release the steam boost button Fig 11 Vertical steam boost You can also use the steam boost function when you hold the iron in vertical position This is useful for removing creases from hanging clothes curtains etc 12 ENGLISH Hold the iron in vertical position and press and release the steam boost button Fig 12 Never direct the steam at people Drip stop This iron is equipped with a drip stop function the iron automatically stops producing steam when the temperature is too low to prevent water from dripping out of the soleplate When
10. he temperature Set the temperature dial to the dial is set to MIN required position The iron There is not Fill the water tank see chapter does not enough water in Preparing for use section Filling produce any the water tank the water tank steam The steam control is set to position 0 Set the steam control to amp or amp see chapter Preparing for use table Temperature and steam settings The iron is not hot Set an ironing temperature that is enough and or the suitable for steam ironing e e to drip stop function MAX Put the iron on its heel and has been activated wait until the temperature light goes out before you start ironing 16 ENGLISH Problem The steam boost function does not work properly Water droplets drip onto the fabric during ironing Possible cause You used the steam boost function too often within a short period The iron is not hot enough You have not closed the cap of the filling opening properly You have put an additive in the water tank You have used the steam boost function at a temperature setting below 000 Solution Continue ironing in horizontal position and wait a while before you use the steam boost function again Set an ironing temperature at which the steam boost function can be used eee to MAX Put the iron on its heel and wait until the temperature light goes out before you use the steam boost
11. the plug the mains cord or the appliance itself shows visible damage or if the appliance has been dropped or leaks Ifthe mains cord is damaged you must have it replaced by Philips a service centre authorised by Philips or similarly qualified persons in order to avoid a hazard ENGLISH Never leave the appliance unattended when it is connected to the ma Thi wit ins s appliance is not intended for use by persons including children h reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or res Ch the appliance instruction concerning use of the appliance by a person ponsible for their safety ildren should be supervised to ensure that they do not play with Do not let the mains cord come into contact with the hot soleplate of he iron Do not use the appliance if the flexible rubber handle parts show visi Caution ble damage Only connect the appliance to an earthed wall socket Check the mains cord regularly for possible damage The soleplate of the iron can become extremely hot and may cause burns if touched When you have finished ironing when you clean the appliance when you fill or empty the water tank and also when you leave the iron even for a short while set the steam control to position O put the iron on its heel and remove the mains plug from the wall socket Always place and use the
Download Pdf Manuals
Related Search