AVR 1565/AVR 1566
Contents
1. 5 Measure the distance from each speaker in your system to the listening position Write down the distances 6 Select Distance The Distance menu will appear DISTANCE p FL 10FT SL 10FT CEN 1OFT SUB 1OFT FR 4 1OFT SR oo 1OFT DELAY RESET OFF UNIT FEET A V SYNC DELAY OmS BACK TO SPEAKER SETUP Use the remote s left and right arrow buttons to change the distance setting on the screen for each speaker so it matches the distance you measured Note If you want you can change the units from feet to meters by selecting Unit and pressing the right arrow button When you re finished select Back To Speaker Setup 7 Select Level The Level Adjust menu will appear LEVEL ADJUST D FL dB SL OdB CEN OdB SUB dB FR dB Sk dB CHANNEL RESET OFF TEST TONE SEQ MANUAL TEST TONE s OFF BACK TO SPEAKER SETUP Use the remote s down arrow button to select Test Tone and press the right arrow button to set Test Tone to ON You will hear test noise through the front left speaker 8 Sit in the main listening position and note the volume of the test noise through the first speaker Press the remote s down arrow button to advance the test noise to each of your system s speakers and note the volume level of the noise in each speaker 9 As you advance the test noise through the speakers use the remote s left and right arrow buttons to adjust the volumes of the channel2. Analog Audio Devices Make analog audio connections from your source devices that do not have HDMI or digital audio connections If you re connecting video sources to the AVR s DVD Video 1 or Video 2 audio inputs you must also connect the source device s composite video output to the corresponding composite video connector AVR Analog Audio Connectors lo OOO DO OUT TAPE IN Stereo Audio Cable not supplied ffir ta Analog Audio Analog Source Device Audio Recorders Connect an analog audio recorder s inputs to the AVR s analog audio Tape Out connectors You can record any analog audio input signal AVR Analog Audio Connectors 00000 OUT TAPE IN Stereo Audio Cable not supplied To Stereo Analog Audio Output Analog Source Device Video Recorders Connect an analog video recorder s video input connector to the AVR s Video 2 Out composite video connector and its audio input connectors to the AVR s Video 2 Out analog audio connectors You can record any composite video signal AVR Analog Video Cc te AVR Analog Audio Connectors SG DA NY Q r SS Cable not supplied n To Analog ee Record Inpt ES Analog Video Recording Device AVR 1565 AVR 1500 Connect the Radio Antennas e Connect the supplied FM antenna to the AVR s FM 75 antenna conn
3. Aux 2 Portable Media Player AVR Source Button HDMI Connector Digital Audio Input Source Device Connected Connector Assigned Input Connections and Source Buttons HDMI Devices If any of your source devices have HDMI connectors using those connectors will provide the best possible video and audio performance quality Since the HDMI cable carries both digital video and digital audio signals you do not have to make any additional audio connections for devices you connect via HDMI cables although you can assign one of the digital audio connectors to one of the HDMI inputs AVR HDMI Connectors Hom 1 c gt c 3 c a OZO gt c gt Cc U HDMI Cable not supplied Homi 2 Hom 3 gt To HDMI Output HDMI Equipped Source Device Component Video Device If your Blu ray Disc or DVD player does not have an HDMI connector but does have a component video connector using the component video connector will provide superior video performance You will also need to make an audio connection from the player to the AVR AVR DVD Component Video Connectors Dur Bu Component Video 4 Cable not supplied To Component Video Outputs Component Video Equipped Blu ray Disc or DVD Player AVR 1565 AVR 1566 Composite Video Devices You will need to make composite video connections fro
4. button Power Button Main Power Switch Configure Your Speakers 1 Turn on your TV and select the TV input where you connected the AVR in Connect Your TV or Video Display on page 3 2 Press the remote control s OSD button The AVR s on screen display OSD Master Menu will appear on the TV MASTER MENU INPUT SETUP SURROUND SELECT SPEAKER SETUP SYSTEM SETUP gt NOTE If any of the menus disappear this is done to prevent TV burn in press the OSD button again 3 Use the remote s arrow and OK buttons to select Speaker Setup The Speaker Setup menu will appear SPEAKER SETUP D NUMBER OF SPEAKERS SUB MODE SUB CROSSOVER DISTANCE LEVEL ADJUST BACK TO MASTER MENU 4 Select Number Of Speakers The Number Of Speakers menu will appear NUMBER OF SPEAKERS LEFT RIGHT ON gt CENTER ON SURROUND ON SUBWOOFER ON BACK TO MASTER MENU AVR 1565 AVR 1566 Use the remote s left and right arrow buttons to select On or Off for each speaker position depending on which speakers you have connected to the receiver When you re finished select Back To Master Menu For now you can skip the Sub Mode and Crossover settings For complete details about making these settings please download the AVR 1565 AVR 1566 Owners Manual from www harmankardon com
5. AVR 1565 AVR 1566 Audio video receiver harman kardon by HARMAN AVR 1565 AVR 1500 Introduction Thank you for choosing a Harman Kardon product This guick start guide contains all the information you need to connect and set up your new Harman Kardon audio video receiver To conserve our natural resources your AVR does not include a printed user manual A user manual containing complete information about operating all of your new AVR s features is available at our Web site Go to www harmankardon com and download the AVR 1565 AVR 1566 Owner s Manual Place the AVR Place the AVR on a firm and level surface Be certain that the surface and any mounting hardware can support the AVR s weight e Provide proper space above and below the AVR for ventilation If you install the AVR in a Cabinet or other enclosed area provide cooling air within the cabinet Under some circumstances a fan may be required e Do not obstruct the ventilation slots on the top of the AVR or place objects directly over them Do not place the AVR directly on a carpeted surface e Do not place the AVR in moist or humid locations in extremely hot or cold locations in areas near heaters or heat registers or in direct sunlight Connections CAUTION Before making any connections to the audio video receiver ensure that the AVR s AC cord is unplugged from the AVR and the AC outlet Making connections with the AVR plugged in and turned on could d
6. E z IN BASS 2 TREBLE u 0 BACK TO MASTER MENU c Use the remote s left and right arrow buttons to select the digital audio input where you connected the source device When you re finished press the remote s OSD button to turn off the on screen menu You are now ready to enjoy your AVR IMPORTANT For complete information about using all of your audio video receiver s features and capabilities download the AVR 1565 AVR 1566 Owner s Manual from www harmankardon com General Specifications Power consumption lt 0 5W standby 250W maximum Dimensions W x H x D 17 5 16 x 6 1 2 x 17 1 16 440mm x 165mm x 435mm Weight 20 Ib 9 1kg 7 HARMAN HARMAN Consumer Inc 8500 Balboa Boulevard Northridge CA 91329 USA 516 255 4545 USA only Made in P R C 2011 HARMAN International Industries Incorporated All rights reserved Harman Kardon is a trademark of HARMAN International Industries Incorporated registered in the United States and or other countries EzSet EQ is a trademark of HARMAN International Industries incorporated Blu ray Disc is a trademark of the Blu ray Disc Association HDMI the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries er countries Features specifications and appearance are subject to change without notice harman kardon harman kardon by HARMAN www harmankardon com
7. amage the speakers HDMI Connectors Radio Antenna Connectors Digital Audio Connectors Introduction Speaker Placement and Connections Place Your Speakers Determine the locations for your system s speakers according to their manufacturer s directions and the layout of your listening room Use the illustration below as a guide M For more detailed speaker placement information download the complete AVR 1565 AVR 1566 Owner s Manual from www harmankardon com Analog Video Connectors SUB WOOFER Analog Audio Speaker Connectors Connectors Subwoofer Connector AVI M ELECTRIQUE NE PAS MODELNO AVR T565 harman kardon Harman Consumer Ine NORTHRIDGE CALIFORNIA USA MADE IN CHINA Main Power Switch AC Input Connector AVR 1565 AVR 1566 Rear Panel Connections AVR 1565 AVR 1300 Connect Your Speakers How to use the AVR s speaker terminals 1 Unscrew Cap 2 Insert Bare Wire 3 Tighten Cap Always connect the colored terminal on the AVR to the terminal on the speaker usually red and the black terminal on the AVR to the terminal on the speaker usually black IMPORTANT Make sure the and bare wires do not touch each other or the other terminal Touching wires can cause a short circuit that can damage
8. ector For the best reception extend the FM antenna as far as possible e Bend and fold the base of the supplied AM antenna as shown and connect the antenna wires to the AVR s AM and Gnd connectors You can connect either wire to either connector Rotate the antenna as necessary to minimize background noise AVR Antenna Connectors FM Antenna Bb supplied AM Antenna supplied RADIO ANTENNAS Bend and fold base NOTE For instructions on connecting the Trigger output to compatible equipment please download the AVR 1565 AVR 1566 Owner s Manual from www harmankardon com Connect to AC Power Connect the AC power cord to the AVR s AC Input connector and then to a working AC power outlet AVR AC Input Connector AC Power Outlet p Power Cord supplied Set Up the AVR Install the Batteries in the Remote Control Remove the remote control s battery cover insert the three supplied AAA batteries as shown in the illustration and replace the battery cover NOTE Remove the protective plastic from the AVR s front panel to keep it from reducing the remote control s effectiveness Connections Turn On the AVR 1 Set the rear panel Main Power switch to On The front panel Power indicator will glow amber 2 Press the front panel Power
9. m your source devices that do not have HDMI or component video connections You will also need to connect the source device s analog audio outputs to the AVR s corresponding analog audio connectors Note If you connected your Blu ray Disc or DVD player to the AVR s DVD Component In connectors do not connect a source device to the AVR s composite DVD In connector AVR Composite Video Connectors Composite Video Cable not supplied To Composite Video Output Composite Video Eguipped Source Device Optical Digital Audio Devices If your source devices have optical digital outputs connect them to the AVR s optical digital audio connectors NOTE Make only one type of digital connection HDMI optical or coaxial from each device AVR Digital Audio Connectors DTA AUDE ny Optical Digital Audio Cable not supplied F To Optical Digital Audio Output Optical Eguipped Source Device Coaxial Digital Audio Devices If your source devices have coaxial digital outputs connect them to the AVR s coaxial digital audio connectors NOTE Make only one type of digital connection HDMI optical or coaxial from each device AVR Digital Audio Connectors Coaxial Digital Audio Cable not supplied To Coaxial Digital Audio Output Coaxial Equipped Source Device Connections
10. our Audio and Video Source Devices Source devices are components where a playback signal originates e g a Blu ray Disc or DVD player a cable satellite or HDTV tuner etc Your AVR has several different types of input connectors for your audio and video source devices HDMI component video composite video optical digital audio coaxial digital audio and analog audio The connectors are labeled for the types of source devices you are most likely to connect Each of your AVR s various source buttons is assigned to an analog audio input connector listed in the AVR Source Button Analog Audio Connector column of the table below To AVR Source Button Analog Audio Connector Recommended Source Device Type Video 1 Cable or Satellite Tuner Connections provide you flexibility for connecting and configuring your system we have designed the AVR so that you can assign the digital audio inputs and component video input to any of the video AVR sources As you connect your source components fill out the Source Device Connected column in the following table it will make it easier for you to assign the digital audio input connectors and component video connector later in the setup process Digital Audio Input Source Device Connected Connector Assigned Video 2 DVD Recorder or VCR DVD Blu ray Disc or DVD Player CD CD Player Tape Cassette Deck or Audio Recorder Aux 1 Portable Media Player
11. s until all of them play at the same volume When you re finished press the remote s OSD button to turn off the on screen menus Assign the Digital Audio Connectors 1 Review the input connections you listed on the Input Connections and Source Buttons table on page 4 Note which source devices you connected to the digital audio connectors If you did not connect any source devices to the digital audio connectors you can skip this section Connections 2 Turn on your TV and select the TV input where you connected the AVR in Connect Your TV or Video Display on page 3 3 Press the remote control s OSD button The AVR s on screen display OSD Master Menu will appear on the TV MASTER MENU 2 p jINPUT SETUP SURROUND SELECT SPEAKER SETUP SYSTEM SETUP 4 Use the remote s arrow and OK buttons to select Input Setup The Input Setup menu will appear INPUT SETUP D SOURCE z DUD TITLE AUDIO IN ANALOG AUTO POLL OFF BAR ORF TONE z IN BASS 2 0 TREBLE 20 BACK TO MASTER MENU 5 For each source device you connected to a digital audio input a Use the remote s up and down arrow buttons to select Source Use the left and right arrow buttons to change the listed source to one of the sources you connected to a digital audio input b Use the remote s down arrow button to select Audio In INPUT SETUP SOURCE z DYD TITLE D AUDIO IN OPT 1 AUTO POLL ON BHR s OFF TON
12. your AVR Connect the speakers as shown in the illustration FRONT RIGHT FRONT LEFT SURR RIGHT SURR LEFT CENTER FRONT RIGHT SURR RIGHT z SPEAKERS 80 Connections Connect Your Subwoofer Use a single RCA audio cable to connect the AVR s Subwoofer Pre Out connector to your subwoofer Consult your subwoofer s user manual for specific information about making connections to it AVR Subwoofer Powered Connector Subwoofer Single RCA Audio Cable not supplied SUB WOOFER Connect Your TV or Video Display HDMI Monitor Out Connector If your TV has an HDMI connector and you have HDMI or component video source devices use an HDMI cable not included to connect your TV to the AVR s HDMI Monitor Out connector It will provide the best possible picture quality AVR HDMI Monitor Out Connector 20 hp HDMI Cable not supplied Composite Video Monitor Out Connector If your TV does not have an HDMI connector or if your TV does have an HDMI connector but you are connecting some source devices with only composite video connectors use a composite video cable not included to connect the AVR s Composite Monitor Out connector to your TV s composite video connector AVR Composite TV Monitor Out Connector MONTOR OUT Composite Video Cable not supplied je AVR 1565 AVR 1500 Connect Y
Download Pdf Manuals
Related Search