User Manual & Spare parts catalogue for the TP 130
Contents
1. 864 1217 Figure 21 Dimensional sketch TP 130 PTO 864 2406 88 84 2207 2362 PTO 528 683 Le 403 558 1235 1416 Figure 22 Dimensional sketch TP 130 MOBILE Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 2008 14 Accessories e Tool kit incl torque wrench e Prolonged ejector tube horizontal e Extension for ejector tube vertical e Lock for ball and socket coupling TP 130 MOBILE e Light boom TP 130 PTO e Sliverbreaker TP130 TP160 e Facing plate Figure 17 15 Spare parts catalogue Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 Copyright 20082. Start The key is turned clockwise to start hold it here to start the motor and then release the key NOTE If the motor does not start after the starter motor has been activated for 10 sec then you must release the key and let the starter motor cool in order to avoid failure Cold motor Gradually move the choke control to the position off after the motor has been started and begun to heat up The motor equipment can be operated during the heating period but it may be necessary to leave the choke control partially on until the motor is hot Hot motor Put the choke control back into the position off as soon as the motor has started Operation handle Starting the wood chipper Start the engine with the key and let it run idle for a few minutes The revolutions of the motor are increased moderately with the throttle Pull the operation handle slowly and the rotor is activated The motor s rotor s revolutions are increased to operational speed with the throttle The wood chipper is now ready for operation Stop Stop putting material in the wood chipper and wait until nothing comes out of the ejector tube By lowering the operation handle the rotor is deactivated and then the revolutions of the motor must be slowed to idle running with the throttle The engine must run idle before it is stopped Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana co
3. gt x lt Anvil turn change Change bow in top rotor housing X Turn change triangle and square X scrapers Check V belts X Check ejector wings for wear X Check casing for wear and tear X The PTO axle is dismantled and 4 lubrication nipples are lubricated with Uniway Li62 or something of similar quality Bolts and nuts are tightened the first time after 8 hours and then with an interval of 50 hours Two lubrication nipples are lubricated with Uniway Li62 or something of similar quality The PTO axle is dismantled and the tube connection is pulled apart cleaned and lubricated The oil is changed for the first time after 50 hours then every 500 hours Pour W80 90 until it can be seen in the looking glass 1 5 Two lubrication nipples are lubricated with Uniway Li62 or something of similar quality 7 Changed for the first time after 50 hours and then every 1000 hours Drain the hydraulic oil and fill with new oil using 12 litres of Hydraway HVXA 46 or oil that has the equivalent specifications The interval between changing oil can be extended by using biodegradable hydraulic oil such as the type Hydraway SE 46 HP and taking oil samples on an ongoing basis The anvil is turned changed depending on need The bow in the top rotor housing is changed depending on need if it is mounted 1 The triangle scraper in the rotor housing is turned changed The
4. The anvil in the machine is used as wearing bar for the knife in order to cut the wood The anvil must be sharp edged otherwise the wood will bend down and the cut will become frayed The machine is equipped with one horizontal anvil with two edges and one vertical anvil The horizontal anvil can be turned Dismantle the three bolts which hold the horizontal anvil The anvil is taken out and turned replaced Before the anvil is put back the anvil and the bearing surface must be cleaned carefully The distance between the knife s edge and the anvil must be 0 5 0 9 mm See Figure 14 The tightening factor for the bolts for the horizontal anvil is 100 Nm 10 KPm Accessory torque wrench Figure 14 Distance between anvil and knife Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 Copyright 2008 19 The vertical anvil is unscrewed and removed from the inside Before a new one is put in the anvil and the bearing surface must be cleaned carefully The anvil is set to a distance of 0 5 0 9 mm to the knives Use a new precision feeler gauge The bolts for the vertical anvil are tightened to 50Nm 5KPm Accessory In the tool kit there is a torque wrench When the anvils have been turned or replaced and all the bolts are tightened the roller housing is lowered with the retract roller in place The spring is put back by using multigrip pl
5. User Manual amp Spare parts catalogue for the TP 130 wood chipper in the park series Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tpOlinddana com www linddana com 1 Introduction Congratulations on your new TP wood chipper Linddana produces TP wood chippers of the finest quality by using the most modern production technologies i a laser cutting CNC technology and robot technology in bright and open production facilities For safety reasons and in order to get maximum pleasure from the wood cutter it is important to read these instructions before use The user manual explains about safety use and maintenance so that the work with the wood chipper will be safe and profitable This manual has been translated from Danish Linddana A S J rgen Due Jensen Managing director Your distributor is always available with spare parts advice and guidance Distributor stamp Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 Copyright 2008 2 EU declaration of conformity Manufacturer LINDDANA A S lholm Bygade 70 lholm 7160 T rring Denmark hereby declares that Wood chipper is in concordance with the provisions of the Machine Directive Directive 06 42 EC and with the national legislation which translates this directive is in concordance with the following othe
6. www linddana com User instructions TP 130 from 27 05 2014 Copyright 2008 5 1 5 Safety instructions Safety regulations Use hearing protectors safety goggles or a similar eye protection close fitting safety clothing and safety shoes When working near roads it can be prudent to wear a west whish reflects the light to be more visible to the other road users The displaying of signs must be in accordance with the Road Traffic Act Minimum age for users of the machine is 18 for training and under surveillance from an adult the age is 16 During operation all body parts must be kept away from the feeding hopper and any moveable parts of the machine Any material that is stuck between the retract roller and the bottom plate must not be attempted removed by hand before the spring has been demounted and the roller part opened Always stand next to the feeding hopper during feeding of the machine Always observe the terrain conditions around the machine It can be dangerous to fall near the machine Before starting the machine check that the safety devices are working properly Especially the stop and return functions on the operation bow The machine must not be started without the ejector tube mounted to the machine Never use the machine in closed or poorly ventilated spaces because of the danger of carbon monoxide poisoning The top part of the machine as well as all other shielding must not be opened removed before the rotor disc
7. 130 from 27 05 2014 Copyright 2008 12 5 3 Noise level The sound effect level and the sound pressure level from the TP 130 PTO have been measured during use at 1000 rpm on the rotor disc powered by a tractor The sound effect level and the sound pressure level from the TP 130 MOBILE have been measured during use at 1000 rpm on the rotor disc powered by the Kohler Command PRO 25 CH730S engine The measurements have been conducted according to test provisions Directive 2000 14 EC 3 July 2000 EN ISO 3744 1995 ISO 11201 1995 ISO 4871 19 March 1997 EN 13525 17 February 2005 The warrantyd sound effect level which will be given by the manufacturer according to directive 2000 14 EC are as follows TP 130 PTO 124 dB A re 1pW TP 130 MOBILE Kohler 124 dB A re 1pW The machine s sound pressure level at the operator s seat is measured according to ISO 11201 at TP 130 PTO 105 dB A TP 130 MOBILE Kohler 103 dB A The above mentioned values have the common uncertainty for the method of measuring and the estimated variation in a product line for the type of machine Detailed information on the measurements and results as well as estimation of uncertainty are found in a thorough report which can be given out on demand The sound level is of such a character that hearing protectors are prescribed during use of the machine 5 4 Environmental instructions When changing hydraulic oil or engine oil oil and used
8. is completely immovable and the tractor s motor is stopped Always stop the machine and the tractor during inspections service or repairs The machine must be uncoupled from the tractor s PTO Tractor mounted machines have to be on the ground before service or repairs are done Always remove the keys from the machine and or the tractor before leaving it After maintenance and repairs the machine must not be started before all bolts are tightened and all safety devices are mounted Three point mounted machines must be coupled to the tractor s three point suspension before use The maximum rpm for the machine 1000 rpm must not be superseded The transmission axle s tube shielding and covering must always be intact Safety chains on the transmission axle have to be properly mounted The length of the PTO axle has to be adapted to the tractor according to the recommendations from the supplier of the PTO axle The ejector tube must not point towards people or areas where there are people There is a safety distance of 20 m in the direction where the chips are thrown AT DANGER PUT THE OPERATION BOW IN NEUTRAL See Figure 10 Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 Copyright 2008 10 During operation the machine s height may not supersede 600 mm over the terrain see fig 9 If this height is not maintained the ope
9. make sure that there are not any objects in the rotor housing Close the rotor housing and tighten the bolts see Figure 15 7 2 4 Adjusting the V belts Pump transmission The retract roller is run hydraulically The hydraulic pump to the retract roller is run by V belts The V belts need to be check regularly or when the belts are suspected to be slack This is how it is done Stop the machine and the drive Uncouple the tractor s PTO Check that the rotor is at a complete standstill by looking at the two coloured axle end Turn the ejector tube so it faces away from the rotor housing see Figure 6 Loosen the bolts which hold the two parts of the rotor housing together and open the rotor housing Loosen the four screws which hold the hydraulic pump in place and adjust the tension by turning the adjusting screw Used belts are allowed to bend 5 3 mm when they are pushed down with 42 N 4 2kg for new belts this number is 48 N 4 8 kg See Figure 18 The belts can be measured with a gauge for this purpose which can be bought as an accessory Measure point for tension Adjusting screw Figure 18 Adjusting the tension When the V belt has been tightened the rotor is turned a few times to make sure that there are no objects in the rotor housing Now the rotor housing has to be closed and the bolts have to be tightened see fig 15 Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www li
10. square scraper on the rotor is turned changed Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 Copyright 2008 16 Lubrication and oil The Wood Chipper is as standard factory filled with hydraulic oil of the type Hydraway HVXA 46 When replacing the oil use the same type of oil or oil with equivalent specifications Do not mix together different types brands of oils As an accessory the Wood Chipper can be delivered factory filled with biodegradable oil of the type saturated ester Hydraway SE 46HP When replacing the oil use the same type of oil or oil with equivalent specifications Do not mix together different types brands of oils Old hydraulic oil and engine oil as well as used oil filters and air filters should be handed in to the local receiving station Lubrication nipples are lubricated according to the maintenance schedule with Statoil Uniway LI62 or a similar product mixed with Uniway LI62 The machine is equipped with a hydraulic oil tank which is integrated in the rotor housing The tank is equipped with a filler neck an air release valve a level glass and a return filter When changing the hydraulic oil the filler neck is opened see Figure 12 The drain plug is unscrewed The oil is drained into a canister for proper removal When the tank is almost empty the tank is sucked empty with an oil suction device T
11. 7 13 pole connector and the safety chain must be coupled to the vehicle and the supporting leg must be raised The hand brake is released before driving Check that lights brake lights and turn signal lights work before driving TP 130 MOBILE Trailer width 1416 mm Trailer length incl ball and socket 3327 mm head Tire assembly 155 80R13 Tire pressure 4 5 bar 65 psi Engine type Kohler Command Pro CH732 In order to avoid destroying the electrical system the following points must be respected 1 Battery connections must be clean 2 When using a battery charger the earth cable on the battery must be dismantled During transport on public roads the ejector tube has to be turned in the opposite direction of the traffic direction and properly secured WARNING Always stop the engine when servicing the wood chipper and the engine and the rotor disc must be at a complete standstill before proceeding When changing knives the 2 bolts which hold the top of the machine can be loosened A safety switch makes sure that the engine cannot be started when the top part of the rotor housing is lifted The switch will stop the engine if the top part is opened without stopping the engine first If the safety switch is defective it must be changed immediately Instruction for wood chipper See TP 130 PTO Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions T
12. P 130 from 27 05 2014 Copyright 2008 25 TP 130 MOBIL is equipped with a 17kW 24hp Kohler Command Pro CH732 Read the manual for the engine It is necessary that when signing in for repairs that you point out that it is a warranty matter By doing this we have the opportunity to write a report and keep and test the parts as prescribed by the factory It is too late to refer to the warranty after repairs have been done The factory warranty runs out two years after date of purchase See other existing terms of sale and delivery For ordering spare parts Remember to state model year of manufacture and spare part number Notice Always use original parts otherwise the warranty is void WARNINGS BE CAREFUL if you are going to touch an engine that is running or has just been stopped Different components especially the exhaust system can be red hot even though you cannot see it The oil dipstick may only be removed from the engine to check the oil or to fill new oil in the engine When filling up with fuel you must avoid open flames Never let the engine run in closed poorly ventilated spaces Before start electrical wiring connections and isolation must be checked Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 Copyright 2008 26 Choke control KOHLE WANE gt PRO 25 ce H MI 4 m Throttle
13. e moved into the middle position A and the rollers can pull the material into the machine This reset handle is a safety measure so you cannot start the rollers by accident so they pull material into the machine Reset handle Operation bow Figure 10 Feeding hopper TP 130 with operation bow and reset handle Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 Copyright 2008 14 B A Figure 11 O Direction to the operation bow gt STOP OOo Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 Copyright 2008 15 7 Maintenance During all maintenance and repairs the machine and the drive must be shut off Tractor mounted machines have to be placed on an even surface and be uncoupled from the tractor s PTO 7 1 Maintenance schedule Interval gt hours 8 3 50 Z 100 Z 2008 500 1000 1 000 m 10 000 m Lubrication of the PTO axle X Check of knives and anvil X Tightening of all nuts and bolts X X Lubrication of main bearings for rotor X disc Tube connection for PTO axle X cleaning lubrication Oil change Rotate gear X Lubrication of roller bearings X Changing of return filter for hydraulic X X pump Change hydraulic oil X
14. ertical marker cannot be reset It is used for registering the machine s total work time Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 Copyright 2008 33 Mounting Mechanical setup and mounting diagram Mounting diagram when using electronic sensors hall or inductive sensors Rotor inductive sensor Rollers hall sensor Valve 0 6 m Power 12V laaaa Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 Copyright 2008 34 Technical data Display 6 digits Power supply 12 Vdc 1 24 A Temperature influence The TP Pilot is completely operational within 10 70 C Pulsations from sensor Max 225 pulsations sec Notice The control monitor has been designed for use in connection with the functions described Any other use of the control monitor as it is risky and exempts the distributor of the control from any type of responsibility Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 Copyright 2008 35 11 Troubleshooting for wood chipper TP 130 Check possible causes before contacting the distributor Problem Possible cause Solution The roller are not spinning satisfactorily No
15. etermined by Linddana at no expense to Linddana In case of changing the defective parts the buyer is obligated to send in the defective parts to Linddana at no expense to Linddana Linddana is entitled to changing the defective goods Linddana s responsibility only covers faults which occur within a year of the goods sold being delivered Linddana has no liability besides those stated in the present item This includes any loss the fault might cause including loss of work loss of earnings and other economical implication losses Warranty conditions If Linddana has decided to grant a warranty then this has faults in the construction material or manufacture A warranty granted by Linddana does not cover faults which occur as a result of imperfect maintenance incorrect mounting changes made by the buyer or wrong use of the good The warranty furthermore does not cover normal wear and tear or deterioration Linddana s warranty obligation presupposes that the buyer documents that a stated fault is not due to the conditions which are exempt from the warranty cf afore mentioned The buyer must let Linddana know in writing about any faults to the goods sold no later than 8 days after the fault should have been realized by the buyer If the buyer does not let Linddana Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 Copyright 2008 37 kn
16. he drain plug is screwed back and new hydraulic oil is slowly filled in 12 litres for TP 130 Oil is filled in until the level glass is half filled Filler neck Level glass Figure 12 Filling hydraulic oil Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 Copyright 2008 17 Safety when cleaning cylinder console and retraction cylinder The retract roller pull the material into the rotor disc and the knives This is how it is done Stop the machine and the drive Uncouple the tractor s PTO Check that the rotor is at a complete standstill Turn the ejector tube so it faces the opposite direction of the rotor housing Figure 6 Loosen the bolts which hold the two parts of the rotor housing together and open the rotor housing With multigrip pliers or something similar the spring is lifted off the retract roller Grab the handle and open the roller housing and push the locking pawl into the lock in the side plate see Figure 13 The roller housing is now secured from falling down There is now access for cleaning and replacing wear parts like knives and anvil Locking pawl Figure 13 Securing with locking pawl Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 Copyright 2008 18 7 2 Changing worn parts 7 2 1 Anvil
17. iers Turn the rotor a few times to make sure that there are not any objects in the rotor housing Close the rotor housing and tighten the bolts see Figure 15 Bolts which hold the two parts of the rotor housing together Figure 15 Tighten of bolts in the rotor housing 7 2 2 Knives The machine is equipped with two knives The knives must always be changed in sets The knives belong together in sets also when they are ground so that they are always of equal width If the knives are not of equal with the rotor will be out of balance which will lead to unnecessary strain on the bearings and vibrations in the whole machine Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 Copyright 2008 20 This is how it is done Stop the machine and the drive Uncouple the tractor s PTO Check that the rotor is at a complete standstill Turn the ejector tube so it faces away from the rotor housing see Figure 6 Loosen the bolts which hold the two parts of the rotor housing together and open the rotor housing The rotor is turned until the rotor lock can go into one of the holes on the rotor Now the rotor is locked see Figure 15 Be careful that your fingers are not near the knives when the rotor is turned Rotor lock Figure 16 Locking the rotor with rotor lock Remove the two nuts which hold the knife and the bearing surface to
18. m User instructions TP 130 from 27 05 2014 Copyright 2008 21 Stop the engine by turning the start key counter clockwise 9 Hydraulics diagram TP 130 without revolution guard Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 Copyright 2008 28 Overall operation The TP Pilot gives you the opportunity to monitor the revolutions of the engine and retract rollers and sounds an alarm when low or high limit values are exceeded Parameters and machine type can be change by entering an access code Valid from version 816 14 See setting table for machine types Different functions and display indications The following functions are included in the computer needed Rotor used with sensor for rotor rpm in practice not under 12 rpm O Programmable revolution guard 1 9999 rpm X e Roller used with sensor for roller rpm in practice not under 12 rpm 9999 whole hours 9999 whole hours Overview of the monitor Marker e Display marker vertical or horizontal at the sides of the display indicates which function is shown at the moment Operation keys e Change between display indications e Starting changes to the marked value e Programming new number values and Display reset e Shows the possible functions values which can be shown in the display Connector e Input for enclosed sensors a
19. mal rom Normal revolutions that the rotor disc has to hold and where the feeding starts Machine According to the setting table for machine types type An alarm is sounded on the retract roller If the rpm on the retract roller goes over the upper limit value Roller blink the display will blink between current RPM and High Adjust the roller speed by turning the manual regulation of the oil quantity for the oil engines When the roller speed goes under the limit value again the current rpm is shown again 10 1 1 Entering the access code When changing the parameters and machine type access code 1001 is required Enter the access code with following procedure 14 With the key you can navigate to the function indication you want to change programmed Then the key is held for approximately 1 second until _c0000 start flashing With the one key the first digit in the value you want to program is now changed or deleted By pressing the E key the marker moves to the next digit in the value and so on until all the y digits are changed programmed The programming menu is left by pressing ME key The access code is required at every change Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 Copyright 2008 Here you see an example for programming of limit values on the rotor Example of changing low limit value to 850 r
20. na com www linddana com User instructions TP 130 from 27 05 2014 Copyright 2008 Figure 4 Lifting with a fork lift truck Figure 5 Lifting with a fork lift truck Min 2m forks Store the manuals for the PTO member with this manual in the manual box on the machine Before operation you must check that the wood chipper cleared of foreign bodies The machine must be uncoupled from the tractor s PTO and for the MOBILE model the key must be removed from the ignition before opening for the rotor Check that the rotor is at a complete standstill Turn the ejector tube so that it faces the opposite direction of the rotor housing see fig 7 Loosen the bolts that hold the upper and lower rotor housing together Lift the top part of the rotor housing up until the ejector tube rests on its own Turn the rotor a few times by hand Remove any foreign bodies Figure 6 Position of ejector tube when opening rotor housing Check that the gap between the knives and the anvil is correct 0 5 0 9mm The knives have a fixed knife position 8 mm Check that the knives are not rubbing on the anvils Lift the top part of the rotor housing back in place and tighten the bolts Check that all bolts nuts and screws are tightened properly Remember to lubricate all the lubrication points see maintenance schedule page 16 Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instruction
21. nd outputs Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 Copyright 2008 29 Explanation for operation keys By pressing the key you switch between the different display indications seen in the window at the left end of the display and thereby the different functions of the monitor With each press on the key the position of the marker display indication changes one step The marker starts in the top left corner and then moves down The key is also used to leave the change menu cf next paragraph so 85 key is used for programming changing deleting values in the computer e g putting in alarm values for high and low revolutions c once Key With ES key the values that are going to be programmed chosen by using the LS key are changed or deleted The computer is equipped with an internal memory which saves all values when the power is cut Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 Copyright 2008 30 Programming The following parameters can be adjusted as desired Meaning L ow Lowest rpm Deviation from normal revolutions If the machine is loaded to under lowest rpm the feeding is uncoupled so that the machine has the possibility to get to normal rom where the rollers start Nor
22. nddana com User instructions TP 130 from 27 05 2014 Copyright 2008 23 7 3 Grinding of knives It is very important for the quality of chips that the knives are sharp They have to be checked at least once a day The grinding interval of the knives can be prolonged by grinding them with a carborundum stone regularly The grinding can be done as wet grinding with a bond stone see Figure 19 Never use an angle grinder or a similar tool for grinding the knives Figure 19 Wet grinding machine When grinding knives you have to pay attention to the width of the knife set The width has to be the same because of the balancing of the rotor Therefore the knives always have to be ground in sets The knives must have a measurement of min 75 mm See Figur 20 After that they must be thrown away The edge of the knives must be ground at an angle of 30 See Figur 20 Figur 20 Grinding angle and minimum knife width for chipping knives Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 Copyright 2008 24 8 Special instruction for TP 130 MOBILE TP 130 MOBILE is a trailer mounted wood chipper comprised of a trailer upon which a wood chipper with own engine is mounted registered as a trailer tool The trailer can be coupled to a vehicle with a ball and socket head as a coupling without inspection When coupling the
23. oil filters and air filters must be handed in at an approved receiving station Oil spills must be avoided as much as possible At oil spills the spilled oil must be cleaned up and handed in at an approved receiving station Worn out parts must be disposed of for recycling When the machine is worn out it must be disposed of properly Hydraulic oil and engine oil must be drained and handed in at an approved receiving station with oil filters and air filters The rest of the machine must be disposed of for recycling Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 Copyright 2008 13 6 Operation of the machine The wood chipper is equipped with one hydraulic roller a control valve and an operation bow with a reset handle see Figure 10 The operation bow must be in the stop position 0 during start see Figure 11 After start you release the reset handle and pull the operation bow into the middle position A and the rollers will turn The material is now pulled into the machine By pulling the operation bow towards you B the flow of oil in the control valve is turned and the roller reverse the material is now pushed out of the machine When the machine is either stopped 0 or reversed B the reset handle will automatically block the operation bow It is now necessary to release the reset handle before the operation bow can b
24. on guard cccccsssssccccsssssseceeees 27 OverallloperatiOn ita idad o dd ada 28 Programming Es 30 MOUNT A a E a a a aia a es aaa 33 Technical data misas e TEA AAA asadas dilo 34 12 Troubleshooting for wood chipper TP 130 ccccccsssssssssssseececcccccsessssseees 35 13 Warranty obligation for wood Chipper ssssccccscsssssssssssseeeeeccccessessssssees 36 14 Technical data wood chipper svcsiviseici ces sds ceucendesivenceavetivadeniveyccecpedsedsotoonsdivanens 37 DS A E A 39 16 Spare parts catalogue iaa 39 Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 Copyright 2008 Use The TP 130 wood chipper is designed for stationary wood chipping in the form of braches etc The machine must not be used for materials containing stone metal or other foreign bodies These foreign bodies can in the best case dull the knives and in the worst case break the machine Knives and anvil can break when stone or metal comes in between them The machine must not be used for wood chipping of wood containing nails screws arming etc When feeding branches you must stand next to the feeding hopper see fig 1 The branches can be thrown around when the retract roller get a hold of them Logs must be fed into the machine from the back see fig 2 Figure 1 Feeding branches Figure 2 Feeding logs Remember to keep the knive
25. ow before the expiration of this deadline and before the warranty period runs out the buyer looses the right to make any claims concerning the fault Linddana is entitled and obligated to remedy any faults which are covered by a warranty granted by Linddana Linddana alone decides if the remedy is to be done as repairs or changes of the defective parts everything under the terms stipulated in item 4 Linddana has no other liability for those faults This includes any loss the fault might cause including loss of work loss of earnings and other economical implication losses The warranty does not cover e Ifa defect with just cause can be attributed to inappropriate use e Use of unoriginal spare parts including worn parts e Wrong adjustment or use of the machine e Use of wrong lubricant or hydraulic oil e Wear on cross at PTO axle e Tightening spring for rollers e V belts e Knives and anvil which break because of foreign bodies in the machine 13 Technical data wood chipper Rotor disc diameter mm 66o 660 1000 Knives pieces 2 18 45 25 60 Knives pieces Chiplengthhmm 8 8 PTO transmission axle Walterscheid type W400 with free running Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 Copyright 2008 38 Rights to changes in the construction and specifications without previous notice reserved
26. pm and high limit value to 1025 rpm Push key The display Explanation shows 0 Find the revolution guard for the rotor by pressing the key repeatedly L X800 Press the key for 1 second enter access code L lights up to the left and the first digit of 4 is flashing os L 800 Press the key until the digit has the correct value Notice that zero appears as _ here L_X00 Press to put change the next digit the second digit will flash os L 800 Press the key until the desired digit is correct L 8X0 Press to put change the next digit the third digit will flash os L 850 Press the key until the desired digit is correct L_85X Press to put change the last digit os L 850 Press the key until the desired digit is correct h X000 Press the arrow key and h high will light up to the left and the first digit of 4 will flash h 1000 Press the key until the desired digit is correct h 1X00 Press to put change the next digit the second digit will flash os h 1000 Press the key until the desired digit is correct h 10X0 Press to put change the next digit the third digit will flash ES h 1020 Press the key until the desired digit is correct h 102X Press to put change the last digit os h 1025 Press the key until the desired digit is correct pan Press to complete and exit the programming menu When an alarm limit on the roto
27. r EC Directives 2000 14 EC Furthermore it is stated that EN 13525 harmonised standard has been used Title Managing director Name J rgen Due Jensen a lholm 27 May 2014 Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 Copyright 2008 3 Table of content de Introduction ina ads 2 2 EU declaration of conformadas aaa 3 3 Table OF contenta 4 O SG E E E E E EE 5 5 Mounting Instructions ini ad Re 6 5 1 NO 6 5 2 Mounting NSC O y a A iii aida 8 6 Saf ty INSEFUCTIONS siria 9 6 1 Satety regulation Sii NA A E A AA AA deans 9 6 2 Pi tograms Used ea a deans heed cae bes ies a Sac danse eleed ae a ane Mie bee 11 6 3 NOISE OVE Miss firs cesses ties E REE AEA ETIE E th deneditbeesats 12 6 4 Environmental instructiOns serae annae a ia aaan aaa a aaa a a a Nan 12 7 Operation ofthe machine s eeoessssssesssseecccsssssessssescccssssesssseeeccssssseessseeeesss 13 A O 15 8 1 Maintenance schedule ooocccccccccccooonnnnnnnnnnnnononononnnnnnnnnnononnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnonnnaannnnos 15 8 2 Changing WO Palta tddi dai 18 8 3 Grinding O PKNIVES rita AS A A AAA A A A 23 9 Special instruction for TP 130 MOBILE ccccccssssssssssssseececcccecssessssssseeeeeees 24 10 Hydraulics diagram TP 130 without revolution guard ooomoccooommmm m gt oso m oo 27 11 Hydraulics diagram TP 130 with revoluti
28. r is exceeded the current rpm is still shown while the retract rollers are stopped If the rotor has been under the lower limit value the retract rollers will start when the rotor s rpm is over the set upper limit value h ex 1000 rpm 31 Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 2008 Copyright 32 Setting table for included machine types Model Rotor Rom Rpmi Rpm1 Type L h Nr TP 130 1000 850 1000 13 Work time on the machine Indication of rotation time on the machine In this display indication the middle horizontal marker is activated on the right side The complete rotation time will be shown as illustrated in the following figure Operation time in Display marker for hours and minutes work time gt Over 99 59 hours minutes will be shown as whole hours Resetting the rotation time on the machine Resetting the rotation time operation time on the machine can be done at any time Push thel key until the display for work time appears After this the following is typed in Push the key The display Explanation shows 72 57 Find job hours by pushing the key repeatedly example 72 57 Hold the key in for five seconds until the number blinks 00 00 Push the key to reset the rotation time Notice The total hour counter bottom v
29. ration safety handle will not work as it should and that may lead to risks of severe personal injury due to retraction E E o O x O gt Figure 9 Maximum height over the terrain e During transport or when the machine is dismantled the PTO axle has to be placed in the machine s carrier bow e Incase of transport on roads the ejector tube is turned so it is placed appropriately within the width of the machine and then it is fixed securely e During transport on public roads the provisions of the authorities must be respected During cleaning of the hopper THE RETRACT ROLLER MUST BE STOPPED e For cleaning a broom or similar must be used Never touch the inside of the hopper when the machine is running Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 Copyright 2008 11 5 2 Pictograms used we EY Warning Objects thrown Warning Rotating knives Warning Rotating roller Safety distance 20m Wait for rotor to stop Warning Rotating belts Warning Danger of retraction Warning Danger of retraction Do not touch the hopper Do not step on the hopper ON Read the manual before use Hearing protector and eye Lifting point for crane protection prescribed Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP
30. s TP 130 from 27 05 2014 Copyright 2008 Old hydraulics and motor oil and used oil filters and air filters must be handed in at an approved receiving station 4 2 Mounting instruction The machine is designed to be mounted on the tractor s three point suspension or trailer mounted with its own engine Machines for mounting on the tractor s three point suspension is delivered with a PTO axle with 1 3 8 6 splines The PTO axle must be mounted with free running on the machine side Linddana uses Walterscheid W400 with free running which comes with the machine The length of the PTO axle has to be adapted to the tractor following instructions from the supplier of the PTO axle See the attached manual for the PTO axle The machine must stand on a plane horizontal surface during use and the tractor mounted machines must be attached to the tractor s three point suspension see Figure 7 The tractor s brakes must be properly activated Trailer mounted machines must also have their brakes activated see Figure 8 When starting the machine Attachment must be done with the motor running at idle speed or at as few revolutions as possible in order to avoid overloading of the PTO axle gear box tractor and wood chipper Three point suspension Figure 7 TP 130 PTO three point suspension Hand brake Figure 8 TP 130 MOBILE hand brake Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com
31. s and anvil sharp it makes feeding easier and gives a better quality chips and besides it lovers the use of fuel considerably The machine must be inspected daily meaning the rotor housing must be opened and the rotor knives anvil etc must be inspected By doing this you prevent unexpected stops and prolong the life of the machine The tractor or trailer upon which the machine is mounted must always have the brakes activated during work The machine must not e Be used for other materials than wood e Be used to push trees stubs etc There must not be equipment like forest chains axes chain saws etc in the feeding hopper Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 Copyright 2008 4 Mounting instructions 4 1 Before use The machine is equipped with a lifting point which is to be used when lifting the machine with a crane or any other hoisting device ground assistance see Figure 3 The machine can also be lifted with a fork lift truck Make sure that the forks of the truck are put all the way through otherwise the machine can tip over see Figure 4 The TP 130 MOBILE is mainly transported on the trailer wheels but it can also be lifted with a fork lift truck see Figure 5 Lifting point Figure 3 Lifting point on the machine Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp lindda
32. t enough oil in the hydraulics system The bypass valve is dirty The revolution guard is blocking The operation bow is in the O position Fill up with hydraulic oil Clean the bypass valve Increase the rpm on the rotor Put the operation bow in the A position The roller are not pulling satisfactorily Not enough flow The V belt are too slack The hydraulic oil gets too hot Too poor viscosity of the hydraulic oil The hydraulic filter is clogged The hydraulic pump is worn or damaged The oil engine is defective The pressure control valve in the control valve is dirty Perform troubleshooting Tighten the V belt Let the machine cool down while checking why Change the hydraulic oil Change the hydraulic filter Change the hydraulic pump Change the oil engine Clean the pressure control valve Chip quality is not satisfactory The knives are dull The anvil is worn The knives are worn too far down The distance between knife and anvil is too big Slotting breaker not mounted or worn Grind the knives Turn change the anvil Change the knives Adjust the distance between the knives and anvil Mount or change the slotting breaker Poor ejection of the chips Not enough drive Scrapers are worn The facing plate in the top part Not enough revolutions on the machine Not enough effect on the PTO axle or the engine Change the scrapers Remove the facing plate in the top part Increase speed to maximum re
33. the casing and reduces the consumption of fuel The square scrapers can be turned once before being changed while the triangle scraper and the facing plate should always be changed when they are worn This is how it is done The rotor is turned until the rotor lock can go into one of the holes on the rotor Now the rotor is locked see Figure 16 Be careful that your fingers are not near the knives when the rotor is turned Dismantle the countersunk bolts which hold the square scraper on the rotor Turn the square so that a sharp edge points up Clean the block and the bearing surface Put the square scraper back If it is worn on two edges the square scraper has to be changed Always change the square scraper on the rotor in sets Change the triangle scraper when it is worn The facing plate is mounted in the top part of the rotor housing and can easily be changed by dismantling two bolts on the outside of the rotor housing If chip quality is not important the facing plate in the ejector tube can be removed This will increase the capacity of the machine and save fuel The facing plate has to be dismantled when chipping wet conifer with a lot of needles Then a good ejection is ensured Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 Copyright 2008 22 When the scrapers have been turned or changed the rotor is turned a few times to
34. the rotor Take out the knife The bearing surfaces on the chipping disc and the knife must be cleaned properly before fitting the knives On fitting the nuts must be slightly greased u 0 125 meaning thin oil WD 40 or something similar Copper grease MoS or similar low friction grease must not be used Check that the distance between the knife s edge and the anvil is set correctly at 0 5 0 9 mm The nuts must be tightened with 110 Nm 11 KPm Use a torque wrench for this which is included in the tool kit This can be bought as an accessory When the knives are changed the rotor is turned a few times to make sure that there are not any objects in the rotor housing Close the rotor housing and tighten the bolts see Figure 15 Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 Copyright 2008 21 7 2 3 Scrapers and facing plate The machine is equipped with two square scrapers on the rotor disc a triangle scraper in the rotor housing The facing plate in the ejector tube see Figure 17 is optional equipment for this machine Facing plate Figure 17 Placement of the scrapers and the facing plate The purpose of the scrapers is to remove any material which might get stuck to the knives At the same time the square scraper on the rotor removes material which falls off in front on the chipping disc This reduces the wear to
35. volutions Linddana A S lholm Bygade 70 DK 7160 T rring T 45 75 80 52 00 tp linddana com www linddana com User instructions TP 130 from 27 05 2014 2008 Copyright 36 12 Warranty obligation for wood chipper The warranty is valid 12 months from date of purchase to rectify defects that irrevocably are due to defects in materials or workmanship The warranty covers faulty components which are repaired or replaced Transportation costs and wages for changes are the responsibility of the customer Upon any claims the changed parts must be sent to Linddana for investigation Linddana alone decides whether the claim can be approved The following is an excerpt from Linddana s Terms of Sales and Delivery item 4 and 5 Claims Any and all risk concerning the goods is passed to the buyer at the time of delivery of the goods A claim concerning the goods has to be done in writing to Linddana as quickly as possible and no later than 8 days after delivery If Linddana has not received the claim before the deadline stated the objections to quantity and quality that the buyer might have will lapse Linddana is entitled and obligated to correct any and all faults which are caused by the construction material or manufacture Linddana alone determines whether the remedy is to be done with repairs or changes of the defective parts In case of repairs the buyer is obligated to deliver and collect the goods sold in the workshop d
Download Pdf Manuals
Related Search