FM1100 with Light Vehicles Can adapter LV
Contents
1. functionality parameters and electrical characteristics without any prior notice and without incurring obligations 2 Safety Introductions This chapter contains information on how to operate device safely By following these requirements and recommendations you will avoid dangerous situations You must read these instructions carefully and follow them strictly before operating the device The device uses a 10 V 30 V DC power supply The nominal voltage is 12 V DC The allowed range of voltage is 10 V 30 V DC To avoid mechanical damage it is advised to transport the device in an impact proof package Before usage the device should be placed in position where all its LED indicators would be visible LED indicators shows status of operation the device is in When connecting the connection cables to the vehicle the appropriate jumpers of the vehicle power supply should be disconnected Before dismounting the device from the vehicle the plug must be disconnected The device is designed to be mounted in a zone of limited access which is inaccessible for the operator All related devices must meet the requirements of standard EN 60950 1 Teltonika is not responsible for vehicle damage caused by installation of adapter Reproduction forbidden without Teltonika UAB written authorization All Rights Reserved pa Qo TELTONIKA 3 Purpose of Light Vehicles Can Adapter LV CAN200 LV CAN200 is used to listening data from light veh2. on vehicle manufacturer and vehicle model Please for further information check Light Vehicles Can adapter supported cars document There are two types of operations with CAN data elements Monitoring of CAN bus data e CAN bus data event capturing Monitoring method is used when user wants to receive CAN data on regular basis for example every 20 seconds Event functionality is used to store additional AVL packet when state of CAN element is changing For example Speed changes low fuel level engine temperate etc Send data to server field allows enabling CAN element so it is added to the AVL data packet and sent to the server By default all CAN elements are disabled and FM1100 records only GPS data It is possible to set CAN message priority On Low Priority On High Priority and On Panic Regular packets are sent as Low priority records When low priority event is triggered FM1100 makes additional record with indication what was the reason for that was CAN element change When High priority is selected module makes additional record with high priority flag and sends event packet immediately to the server by GPRS Panic priority triggers same actions as high priority but if GPRS fails it sends AVL packet to server using SMS mode if SMS is enabled in SMS settings Data Acquisition Type defines when to generate event when value enters defined range exits it or both also is possible to select event which you want to
3. 00 o Reproduction forbidden without Teltonika UAB written authorization All Rights Reserved 10 12 QXYTELTONIKA 7 References 1 Light Vehicles Can adapter LV CAN200 Supported cars 2 Cars mounting scheme 3 FM1100 User Manual Reproduction forbidden without Teltonika UAB written authorization All Rights Reserved Ih il Qo TELTONIKA 8 Changelog Verion a S Reproduction forbidden without Teltonika UAB written authorization All Rights Reserved TTZ
4. QXTELTONIKA FM1100 with Light Vehicles Can adapter LV CAN200 Manual V1 0 Reproduction forbidden without Teltonika UAB written authorization All Rights Reserved ligule Qo TELTONIKA TABLE OF CONTENTS T EEIN Ca hes crs sec ss ee sts cette etc ct etnies pete E eae ecaneeneeee ae eeee eee 3 2 Safety Introductions oceniane E sic ndnastatadasdpns E E NS 3 3 Purpose of Light Vehicles Can Adapter LV CAN200 ccccccsseccccsececeeseceeeneceteuecsseeseceeeueseneness 4 3 1 Selecting light vehicles CAN LV CAN200 program cccccccsececesscceseceeneceeeeceeeseeeneeteneetens 5 4 Connecting FM1100 with Light Vehicles Can adapter ccccccescccesecceeecececeeeneeteeeeeeceeesenes 6 D PIV eC ONS U OID ereenn 7 o PFa Neer Or ert ee etn Perr eres teens ne reer ree eee tere ree eee re 10 F REONE iar cease eects canescens A E 11 CVI EIOP srr cess pac cence setae ce ctv eo snes E E E E 12 Reproduction forbidden without Teltonika UAB written authorization All Rights Reserved ane 1 Legal Notice Copyright 2012 Teltonika All rights reserved Reproduction transfer distribution or storage of part or all of the contents in this document in any form without the prior written permission of Teltonika is prohibited Other products and company names mentioned here may be trademarks or trade names of their respective owners The manufacturer reserves the right to make changes and or improvements at any time in design
5. adapter Pin 1 and Pin 2 to cars CAN bus CAN interface location of the supported light vehicles are described in Connection of LV CAN200 manual Connect car power supply lines to Pin 3 positive Pin 4 Negative Pins 9 10 connection is optional it depends on exact car model For exact pinout see sticker on Light Vehicles Can adapter canan TAKIL i LV CAN200 aaa nuse gt To FM11XX WOE 12 t aay ma CANIL fa CAHIH ei Figure 3 LV CAN200 Adapter connection cable pinout Attention For detailed connection diagram of adapter to light vehicle please contact Teltonika LTD sales representative and provide CAR manufacturer model and year information Do not swap power supply lines Make sure that voltage do not exceeds 30V Power supply lines should be connected at the end of installation work i Attention Do not swap CAN L and CAN H lines Reproduction forbidden without Teltonika UAB written authorization All Rights Reserved 6 12 5 FM11 Configuration To use LV CAN200 adapter with FM1100 device you need to have a FM11 firmware number 43 XX XX b FM11 configurator version 1 43 XX XX For firmware and configurator please contact Teltonika sales manager FM1100 shares the same USB port for connecting LV CAN200 adapter and configuring device with PC FM1100 can be configured using SCAN function or Offline Configuration Figure 8 SCAN function is in use when FM1100 is conne
6. cted to CAN adapter Figure 6 then wait 10s Note that car engine must be started disconnect adapter from FM1100 and connect PC USB cable to FM1100 Device Figure 3 It is very important not to disconnect FM1100 from power source during this operation because if FM1100 is reconnected all received CAN bus data will be lost FM1100 remembers received data from LV CAN200 and at the end of the procedure when SCAN button is pressed user will see all CAN data which is sent by adapter Enable CAN data which needs send to server and save configuration pressing Save button To configure CAN data 1 In car connect LV CAN200 to CAN bus and to the FM1100 device Figure 6 wait 10 seconds Note that car engine must be started 2 Disconnect LV CAN200 from FM1100 and connect PC USB cable to FM1100 Device Figure 7 It is very important not to disconnect FM1100 from power source because then all CAN data will be lost LV CAN200 Connection Figure 4 Connect adapter LV CAN100 to FM1100 USB Cable Figure 5 Connect FM1100 to PC and configure CAN bus data which can be read from your car is shown in Light Vehicles Can adapter Supported cars document Reproduction forbidden without Teltonika UAB written authorization All Rights Reserved aie Offline configuration user can select which CAN data can be read from LV CAN200 need to be sent to server without connection to adapter Please note that parameters depend
7. generate then you change values like crossing both values in high and low levels Hysteresis High and Low levels defines CAN value range If CAN value enter or exits this range FM1100 generates event by Data Acquisition Type settings Figure 6 show example of FM1100 CAN configuration Reproduction forbidden without Teltonika UAB written authorization All Rights Reserved 8 12 Qo TELTONIKA Records DataAcquisitionModes Features Figure 6 Configurator example Available CAN Bus IO parameters and configuration can be found in Configurators CAN tab Figure 8 and in next chapter Parameters ID Reproduction forbidden without Teltonika UAB written authorization All Rights Reserved 9 12 Qo TELTONIKA 6 Parameters ID When no I O element is enabled AVL packet comes with GPS information only After enabling I O element s AVL packet along with GPS information contains current value s of enabled I O element AVL packet decoding is described in FMXXXX Protocols document List of available CAN bus data parameter size ID and value range you can find in table 1 Table 1 ACQUIRED PARAMETRS IO ID Vehicle Distance Total Fuel Used Fuel Level o Fuel Level liters Engine RPM Vehicle Speed Accelerator Pedal Position 83 85 81 21474836475 meters 0 2147483647 liters 0 100 o 0 100 liters 0 8200 rpm 0 250 km h 0 1
8. icles With this adapter FM1100 device is able to collect and send vehicle data FM1100 LV CAN200 Figure 1 Connection block diagram FM1100 shares the same USB port for connecting adapter and configuring device with PC LV CAN200 Technical characteristics PARAMETER VALUE Supply voltage 10 to 30V Power supply current Average 10mA pee et 08 Reproduction forbidden without Teltonika UAB written authorization All Rights Reserved ne Qo TELTONIKA 3 1 SELECTING LIGHT VEHICLES CAN LV CAN200 PROGRAM Steps to set program number Hold SWITCH down till LED stars blinking Release the SWITCH Then LED starts blinking and counting first digit of program number one blink means digit 1 two blink digit 2 etc To stop counter push SWITCH Release the SWITCH then LED starts blinking and counting second digit of program number To stop counter push SWITCH Release the SWITCH then LED starts blinking and counting third digit on program number To stop counter push SWITCH Release SWITCH if programming is succeded LED will blink 10 times Needed program number you will get with mounting scheme Figure 2 Adapter signaling led Reproduction forbidden without Teltonika UAB written authorization All Rights Reserved Syilyd 4 Connecting FM1100 with Light Vehicles Can adapter Connect USB Plug to FM1100 device connect Light Vehicles Can adapter to other end of the cable Connect Light Vehicles Can
Download Pdf Manuals
Related Search