Installation Guide
Contents
1. but A X not too tight Do not crush the wood Use a measuring tape to assure This may create splinters and cause proper location structural damage MATERIAL LIST LR Top and Bottom Rail 2x 7 1 4 18 4cm and 2x 20 50 8cm 8 x 2 1 4 Wood Screw 10 x 1 Pan Head Screw 8 x 1 1 2 Wood Screw 3 3 Post Caps 12 Panel Clips I 2 Arch Topper SZ S LIO N w l O wr Xx N S Q w M x lt I N EJ wn o A x lt lt eine Px2 2 Two High X Panel STEP 1 ASSEMBLE WINGS Remove the upper metal connectors on both sides of PX2 Two High X Panel Reattach the metal connectors to PX2 by securing the bottom two holes of the metal connectors to the top two holes on PX2 so that the metal connectors stick out from the top Slide PA1 Arch Topper between the two protruding metal connectors on the top of PX2 Attach the metal connectors to the factory drilled holes in PA1 Fig 1A Ensure Panels are oriented correctly Fig 1B Groove Thick Pi Skinny Piece Secure panels with a S4 2 of Wood a a 1 4 Wood Screw the location indicated by the large arrow in the direction of the arrow When pre drilled holes are not available use a 1 8 Drill Bit to drill holes on an angle in the inside of the panel as shown Fig F Secure R Top and Bottom Rails to Panel Assembly with S4 2 1 4 Wood Screws locatio2. View Side View Fig 1 138 2cm 44 44 111 8cm 111 8cm 38 38 96 5cm 96 5cm 96 5cm 2x 4x4 Post AT 49 1 4 1 25M 12X PANEL CLIPS 1x 4x4 POST AT 63 1 60M 24x G7 8 X 1 1 2 WOOD SCREW STEP 3 ATTACHING POST CAPS 1 Place a Post Cap on each 4x4 Post 2 Secure Post Cap with 2 S7 8 1 1 2 Wood Screws ce a 3X POST CAPS 6X G2 8 1 1 2 WOOD SCREWS 1 Place panel assemblies on posts as shown Fig 1 allowing a 2 gap between the bottom of the post and the bottom edge of the bottom rail on the panel assembly Note Assemble with the help of another adult 2 With a 1 8 drill bit predrill holes as shown in figure 2 3 Fasten the panel assembles to the post and Panel Clips with a S5 1 Pan Head Screw provided in location of circles Fig 1 Posts must be securely installed to support structure Consult local building codes and ground conditions for required footing design It is recommended the structure be secured to existing stone concrete or deck Fig 2 Predrill Holes and Fasten with S5 1 Pan Head Screw 12x 10 X 1 PAN SCREWS
3. INSTALLATION MANUAL G006 CORNER CLIMBER YM11554 Yardistry Ltd Mount Forest ON Canada NOG 2L1 Toll Free Customer Support 1 888 509 4382 info yardistrystructures com www yardistrystructures com Revised 08 24 2011 TMPORTANT SAFETY NOTICE Yardistry components are intended for privacy decorative and ornamental use only Product is NOT INTENDED for the following Asafety barrier to prevent unsupervised access to pools hot tubs spas or ponds Safety railings for elevated platforms or decks As load bearing support for a building structure heavy objects or swings Used in structures that trap wind rain or snow that would create extra load on the product Permanent structures may require a building permit As the purchaser and or installer of this product you are advised to consult local planning zoning and building inspection departments for guidance on applicable building codes and or zoning requirements Wood is NOT flame retardant and will burn Grills fire pits and chimneys are a fire hazard if placed too close to a Yardistry structure Consult user s manual of the grill fire pit or chimney for safe distances from combustible materials During installation follow all safety warnings provided with your tools and use OHSA approved safety glasses Some structures may require two or more people to install safely Check for underground utilities before digging or driving stakes into the ground Gene
4. ns indicated by arrows in the direction of the arrow R Top and Bottom Rails Oe en ANAE will overhang 1 4 on either side of panel Except on Arch Topper R Top and Bottom Rails may need to be cut to 20 50 8cm and 7 1 4 18 4cm It is recommended to use a Mitre Box or Mitre Saw D e S E I l 4 Repeat until two panel assemblies are created G O O_O Ga Fig 1B Filler Strips on Bottom of Panel 2X ARCH TOPPER 2X k TOP amp BOTTOM RAIL AT 7 1 4 18 4CM 2X TWO HIGH X PANEL 2X k TOP amp BOTTOM RAIL AT 20 50 8CM 8x 8 2 1 4 WOOD SCREWS STEP 2 ATTACH PANEL CLIPS FOR WINGS 1 On a flat surface place P 4x4 Post on its side and position Panel Clips in locations indicated in Figures 1 and 1A Ensure Panel Clips are oriented as shown in Diagrams Panel Clips should be placed in the centre of the post or the leading edge of the clip should be 1 3 8 or 3 49cm away from the side of the post as shown in Fig 2 13 8 3 5cm With Panel Clips in place mark screw holes with a pencil and pre drill holes with a 1 8 drill bit Not provided ill holes and secure with S7 8 x 1 1 2 Wood Screws Secure Panel Clips in locations indicated in figure 1 and 1A with S7 8 x 1 1 2 wood screws Repeat for each post configuration Fig 1A Top View Note Post A has Panel Clips on two sides Front
5. ral Information Wood components are manufactured with Cedar C Lanceolata which is protected with factory applied water based stain Knots small checks cracks and weathering are naturally occurring and do not affect the strength of the product Annual application of a water based water repellent sealant or stain will help reduce weathering and checks Warranty Yardistry Limited products are backed by a 5 year limited lifetime warranty from the date of original retail purchase for manufacturing defects and if installed as per manufacturer s installation instructions Patents Pending Tools Required e Tape Measure e 2 Phillips or Robertson e Safety Glasses Bits or Screwdriver e 1 8 Drill Bit e Pencil e Carpenters Level e Adult Helpers e Carpenters Square e Standard or Cordless Drill e 8 Step Ladder Keys To Assemble Success This identifies information that requires special Check that set or assembly is properly level attention Improper assembly could lead to an before proceeding unsafe or dangerous condition Where this is shown 2 or 3 Pee dnl 1 0 3 10 Bit Pre drill a pilot hole people are required to safely C complete the step To avoid p Fa before fastening screw injury or damage to the A6 or lag to prevent assembly make sure to get help splitting of wood Use Use Help Help Tighten Bolts Measure Check that assembly is square Square Distance j j Assembly i This indicates time to tighten bolts
Download Pdf Manuals
Related Search