KEYTEC VIEW TOUCH USER`S MANUAL Rev. 110812
Contents
1. KEYTEC VIEW TOUCH USER S MANUAL Rev 110812 1 How does View Touch work A digital light sensor is connected to a computer s USB port and set up to view the entire projection screen After running a calibration program and adjusting the sensitivity the digital sensor can capture laser light or other bright light projected on the screen and translate to a mouse function The laser pointer or other light source can then be used as a mouse control device Compatible with Windows and support Windows 7 multi touch gestures 2 What s included Digital light sensor mini tripod laser mouse AA battery installation CD manual warranty card You must have your own PC with Windows XP and up projector and projection screen board wall 3 Software Installation Procedures 3 1 If there is a previous View Touch installation remove it first using add remove program in control panel 3 2 Do not plug in the digital light sensor before the software installation 3 3 Insert CD the Windows Installation Wizard should start If not run setup exe from CD Rom 3 4 Click Next in View Touch Installation Wizard then click Install 3 5 When prompted by Windows compatibility warning message click Continue Anyway in Software Installation 3 6 If your computer does not have DirectX installed click I accept the agreement in Installing Microsoft DirectX then click Next then Finish This step will be automatically skippe2. d if you already have DirectX installed in your computer 3 7 Software installation is completed click Finish in View Touch Installation Wizard 3 8 Plug the digital light sensor into a USB port You may use active USB extension cable or powered USB hub to extend it 3 9 Windows may update the driver automatically or start Found New Hardware Wizard click Yes this time only then click Next then click Install the software automatically then click Next 3 10 When prompted by Windows compatibility warning message click Continue Anyway in Software Installation 3 11 Click Finish to complete the Found New Hardware Wizard 4 Hardware Installation Procedures 4 1 The digital light sensor has a standard tripod mounting hole It can be mounted on the mini tripod included or any standard camera tripod It can also be mounted upside down from the ceiling 4 2 The digital light sensor should be positioned at a distance from the screen that is twice of the width of the projected image on the screen If it is positioned too close then the digital light sensor cannot cover the entire screen It can be positioned farther away but the resolution will become lower 4 3 For the best results the digital light sensor should be positioned within 15 along the center line of the screen both vertically and horizontally If not it may result in increasingly uneven sensitivity due to the uneven distances be
3. ing laser to the screen and see if mouse cursor matches to the position of laser light Recalibrate if necessary If you need to reposition the sensor press Reset button Adjust the sensitivity scale at right until the laser mouse can move the cursor freely 4 13 Click the top button on the left to set speed levels fast smooth super smooth responding to the speed of mouse clicks 4 14 Click Options to open the selections Although it is defaulted at Normal which is good when using on rear projection screen in close distance Otherwise click Move only so the laser light only moves the cursor and does not activate the mouse click Use the buttons on laser mouse to activate the clicks 4 15 Multi touch option If you use Windows 7 you can click Enable Multi button to enable the multi touch capabilities with multiple laser pointers The speed level will drop when the multi touch is enabled 4 15 View Touch Pen Simulate Mouse Lett Re startup Automaticall 4 12 Click Calibration button The digital light sensor takes a screen shot of a grid image and place it in the center window Using your mouse place the cursor at the center of each cross point of the grid 9 total then click to place the calibration point Start at the upper left corner continue clockwise o around the figure finishing in sensitivity the center of the pattern 5 x Disable Enable Defa
4. nquiry sales magictouch com for tech support tech magictouch com
5. tween the sensor and the screen 4 4 The laser mouse has a RF USB receiver on one end Pull it out and insert into a USB port on your computer Open the battery cover at the back insert one AAA battery 4 5 The mode switch at the left side of the laser mouse must be Laser pushed forward to activate the left right mouse clicks as indicated in gt Button the left picture 4 6 Press the laser button to turn on the red laser to move the mouse laser left cursor to the target Release the laser button press the 2 button to mouse click activate the right click press the 3 button to activate the left click Y 4 7 There is a D ring kept in between laser button and the 2 button i Push the D ring forward to press and hold down the laser button so USB the laser beam is constantly turned on then you can use the finger to receler press on the 3 button to drag and draw mode switch KEYTEC INC View Touch Setup www magictouch com Display type Front Projection Rear Projection Display 4 8 Find the two icons on the desktop Double click on VTouch icon to open Sa REBROHOKERIGR the View Touch Setup window VTouch Pen is for annotation and Power Point me control Upside Up Upside Down 4 9 Display Type Select whether your computer screen is projected onto a screen wall specify front or rear projection Display LCD Plasma etc is not recommended unless the laser light can be seen peee Sensor Orientation Select
6. ult OK Cancel This menu contains the tool buttons The Pen button shows the annotation menu and Normal modes see 4 14 Smooth see 4 13 Power Point Control Buttons include Home returns to the first slide Left point arrow goes to previous slide Right point arrow goes to next slide END End advances to the last slide End PPT End PPT will exit the slide show Close View Touch Pen The Mouse button extends to Right click Move only Lift off The Speed button extends to Fast Smooth and Super This menu contains the View Touch Pen s annotation options Click on the Pen to extend color and width selections for pen and highlighter You can draw mark and write on the screen over any program Click Save to save the entire screen annotations and all as a snap shot in either BMP or JPG format Use Undo and Redo like you would in any graphic editing or word processing program Click Trash to clear the screen of annotations Click the Return Arrow to return to the mouse control menu shown in the left column Note When in Pen mode the mouse functions are disabled KEYTEC INC 520 Shepherd Drive Garland Texas 75042 USA Tel 972 272 7555 or 800 624 4289 Fax 972 272 7501 Hours 8 30AM 5 00PM CST Mon Fri Homepage www magictouch com View Touch page http www magictouch com ViewTouch html Email for information info magictouch com for sales i
7. whether the digital light sensor is mounted Upside down from ceiling or Upside up In Front of the Screen Behind the screen Sensor Location Select whether the digital light sensor is located in front of the screen or behind it rear projection aitupAnomec ik Startup Automatically Select if you want the View Touch software starts automatically on computer start up previous calibration data will be loaded Disable Enable Once all selections are made press Start to open the control panel 4 10 The center picture in picture window in control panel shows what the digital light sensor sees Adjust its position until the entire projected image is covered You may check it by emitting laser light to the 4 corners of the projected image to make sure all the corners are covered 4 11 Avoid bright spots appearing on the screen image whether caused by Click to select the above settings then click Start Default Start Exit nearby lamps light fixtures light from the projector or other sources of strong light in the room Otherwise the sensor will become fixated on it causing the cursor to stick to the bright spot To free your cursor simply block the digital light sensor Then adjust the angle of the projector or dim the room lights or move lamps until the bright spot is removed Super Smooth Calibration Load Calibration View TouchPen Options Minimize Check the accuracy by point
Download Pdf Manuals
Related Search