PCA T5 ECO lp 14–80 W 220–240 V 50/60/0 Hz
Contents
1. 2 0 m ballast must be earthed digital signal DSI or switchDIM PCA T5 ECO Ip x tec 2x14 49W PCA T5 ECO Ip 2 80W Dimmable ballasts from TridonicAtco have to be earthed Operation on DC voltage Our ballasts are construed to operate DC voltage and pulsed DC voltage To operate ballasts with pulsed DC voltage the polarity is absolute mandatory For further technical information please visit www tridonicatco com Data sheet 09 11 839 3 We reserve the right to make technical changes without prior notice Isolation and electric strength testing of luminaires Electronic devices can be damaged by high voltage This has to be considered during the routine testing of the luminaires in production According to IEC 60598 1 Annex Q informative only or ENEC 303 Annex A each luminaire should be sub mitted to an isolation test with 500 V DC for 1 second This test voltage should be connected between the interconnected phase and neutral terminals and the earth terminal The isolation resistance must be at least 2 MQ As an alternative IEC 60598 1 Annex Q describes a test of the electrical strength with 1500 V AC or 1 414 x 1500 V DC To avoid damage to the electronic devices this test must not be conducted TRIDONIC 52. dimming operation from 100 1x28 T5 PCA 1x28 54 T5 ECO Ip xitec 1 00 to 30 If dimm level goes below 30 malfunction 2x28 15 PCA 2x28 54 T5 ECO Ip x tec 1 01 possible but no electronic ballast dammage 1x54 T5 PCA 1x28 54 T5 ECO Ip xitec 1 00 This applies to AC and DC operation 2x54 T5 PCA 2x28 54 T5 ECO Ip x tec 1 01 1x35 15 PCA 1x35 49 80 T5 ECO Ip x tec 0 99 2x35 T5 PCA 2x35 49 T5 ECO Ip x tec 0 98 Lamp type recognition 1x49 T5 PCA 1x35 49 80 T5 ECO Ip x tec 1 02 Each of the lamps for wich the control gear is designed a9 15 PCA 2x35 49 T5 ECO Ip x tec 1 00 will be operated correctly according the lamp 1x80 T5 PCA 1x35 49 80 T5 ECO Ip xtec 1 02 specifications The currently used lamp is recognised 2x80 T5 PCA 2 80 T5 ECO Ip 1 00 during the start up process To avoid an incorrect lamp recognition due to fast The ballast lumen factor for AC operation AC BLF does not alter from Un 198VAc to Un 254 Vac multiple ON OFF switches new lamp data are only The ballast lumen factor for DC operation DC BLF on the basis of an automatic power reduction of the ballasts restored if the lamp has operated for at least 5 default value is 70 will be smaller than AC It does not alter in the DC operating range 198 280 V Dc seconds Harmonic distortion in the mains supply at 230V 50 Hz wattage lamp Ballast WwW type type THD 3 5 7 9 11 1x14 T5 PCA 1x14 24 T5 ECO Ip x tec 10 2 5 4 6 1 3
3. friendly warm start within 0 5s with AC ing at any dimming level and cut off the electrodes 825 pieces pallet to EN 50172 and 0 2 with DC at approx 90 dimmlevel for maximum energy power consumption in standby mode lt 0 5W efficiency e disturbance free precise control with a digital e backwards compatibility adjustable DSI signal or switchDIM e corridorFUNCTION V2 with 3 profiles e fully digital lamp management for flash free starting at any dimming level Lamp Ballast wattage type type article length fixing weight circuit lamp current tc point temperature number L centres power power at 230V 50Hz at 230V 50Hz range Ww mm D mm kg we wo A oC mex 1x14 5 PCA 1x14 24 T5 ECO Ip x tec 22176247 360 350 0 25 16 0 1x14 0 08 0 95 80 25 gt 60 2x14 5 PCA 2x14 24 T5 ECO Ip x tec 22176248 360 350 0 28 32 5 2x14 0 15 0 97 80 25 gt 60 1x24 5 PCA 1x14 24 T5 ECO Ip x tec 22176247 360 350 0 25 25 5 1x24 0 12 0 97 80 25 gt 60 1x24 TC L PCA 1x14 24 T5 ECO Ip xttec 22176247 360 350 0 25 25 5 1x24 0 12 0 97 80 25 gt 60 2x24 15 PCA 2x14 24 T5 ECO Ip x tec 22176248 360 350 0 28 51 0 2x24 0 23 0 98 85 25 gt 60 2x24 TC L PCA 2x14 24 T5 ECO Ip x tec 22176248 360 350 0 28 51 0 2x24 0 23 0 98 85 25 gt 60 1x21 5 PCA 1x21 39 T5 ECO Ip x tec 22176245 360 350 0 25 23 5 1x21 0 11 0 95 85 25 gt 60 2x21 5 PCA 2x21 39 T5 ECO Ip x tec 22176246 425 415 0 35 45 5 2x21 0 21 0 97 80 25 6
4. 0 Digital control with DSI signal 8 bit Manchester Code Speed 1 to 100 in 1 4s Control input D1 D2 Digital DSI signal push to make switch switchDIM or a motion detector corridorFUNCTION can be wired on the same terminals D1 and D2 Digital signal DSI The control input is non polar and protected against accidental connection with a mains voltage up to 264V The control signal is not SELV Control cable has to be installed in accordance to the requirements of low voltage installations Different functions depending on each module SMART interface An additional interface for the direct connection of the SMART LS II Ip light sensor or corridorFUNCTION Plugs Application and functionallity see corridorFUNCTION user manual SMART LS II Ip light sensor operating mode The sensor registers actual ambient light and main tains the individually defined lux level After every mains reset the SMART interface auto matically checks for an installed sensor With the sensor installed the PCA T5 ECO Ip x tec automati cally runs in the constant lux level mode ON OFF switch via mains switchDIM or DSI signal DSI signal 0 switches off DSI signal gt 1 switches on With switchDIM signals it is possible to change the controlled light level temporarily Temporarily means that after a switching cycle OFF ON command the ballast will start at the preset value determined by the SMART LS II Ip The installation of
5. 0 1x39 T5 PCA 1x21 39 T5 ECO Ip x tec 22176245 360 350 0 25 42 0 1x39 0 20 0 97 85 25 60 1x40 TC L PCA 1x21 39 T5 ECO Ip xttec 22176245 360 350 0 25 42 0 1x39 0 19 0 97 80 25 60 2x39 5 PCA 2x21 39 T5 ECO Ip x tec 22176246 425 415 0 35 82 5 2x39 0 38 0 99 85 25 gt 60 1x28 5 PCA 1x28 54 T5 ECO Ip x tec 22176243 360 350 0 26 30 5 1x28 0 15 0 95 80 25 gt 60 2x28 5 PCA 2x28 54 T5 ECO Ip x tec 22176244 425 415 0 35 60 5 2x28 0 28 0 97 80 25 gt 60 1x54 5 PCA 1x28 54 T5 ECO Ip x tec 22176243 360 350 0 26 59 5 1x54 0 27 0 98 85 25 gt 60 2x54 T5 PCA 2x28 54 T5 ECO Ip x tec 22176244 425 415 0 35 116 5 2x54 0 53 0 99 85 25 55 1x35 5 PCA 1x35 49 80 T5 ECO Ip x tec 22176241 360 350 0 27 38 5 1x35 0 18 0 97 80 25 60 2x35 5 PCA 2x35 49 T5 ECO Ip xtec 22176242 425 415 0 34 75 0 2x35 0 33 0 97 80 25 60 1x49 5 PCA 1x35 49 80 T5 ECO Ip x tec 22176241 360 350 0 27 53 0 1x49 0 24 0 97 80 25 gt 60 2x49 5 PCA 2x35 49 T5 ECO Ip x tec 22176242 425 415 0 34 105 5 2x49 0 47 0 98 85 25 gt 60 1x80 5 PCA 1x35 49 80 T5 ECO Ip x tec 22176241 360 350 0 37 86 5 1x80 0 39 0 98 85 25 gt 60 2x80 T5 PCA 2 80 T5 ECO Ip 22176054 425 415 0 35 164 5 2x80 0 75 0 99 80 25 gt 50 10 C to ta max normal diming operation 25 C to 10 C dimming operation from 100 to 30 25 C to 10 C dimming below 30 Ballast could shut down but will not cause fa
6. 13 B16 B20 Installation 1 5 mm 1 5 mm 1 5 mm 2 5 mm 1 5 mm 5 mm 1 5 mm 2 5 mm PCA 1x14 24 T5 ECO Ip x tec 50 80 110 135 25 40 75 90 PCA 2x14 24 T5 ECO Ip x tec 24 34 48 52 12 7 24 26 PCA 1x21 39 T5 ECO Ip x tec 34 50 76 86 17 25 38 43 PCA 2x21 39 T5 ECO Ip x tec 16 22 32 36 8 1 16 18 PCA 1x28 54 T5 ECO Ip x tec 24 34 48 52 12 7 24 26 PCA 2x28 54 T5 ECO Ip x tec 16 22 32 34 8 1 16 17 PCA 1x35 49 80 T5 ECO Ip x tec 16 24 32 38 8 2 16 19 PCA 2x35 49 T5 ECO Ip x tec 16 22 32 34 8 1 16 17 PCA 2 80 T5 ECO Ip 10 14 20 22 5 7 10 11 Continuous operation to calculate the protective saftey switch see main current page 1 Data sheet 09 11 839 3 We reserve the right to make technical changes without prior notice TRIDONIC Electronic ballasts for dimming to 1 Linear lamps T5 16mm high efficiency high output corridorFUNCTION Activation To activate the corridorFUNCTION a voltage of 230V simply has to be applied for five minutes at D1 D2 The unit will then switch automatically to the corridorFUNCTION Deactivation If the corridorFUNCTION is wrongly activated in a switchDIM system for example a switch is used instead of pushbutton there is the option of installing a pushbutton and deactivating the corridorFUNCTION mode by five short pushes of the button within three seconds The corridorFUNCTION V2 offers the added benefit of a second and third preprogrammed profile which can be activated by the corridorFUNCTION plugs Applic
7. 2 2 2 1 6 2x14 T5 PCA 2x14 24 T5 ECO Ip x tec 7 8 4 3 2 5 2 5 27 22 1x24 1x14 T5 TC L PCA 1x14 24 T5 ECO Ip x tec 6 1 6 9 4 6 5 8 1 1 1 1 1 2 1 4 1 2 1 2 1 2 1 3 2x24 2x24 T5 TC L PCA 2x14 24 T5 ECO Ip x tec 4 8 8 5 3 2 6 2 1 4 1 8 2 0 2 7 1 3 1 9 1 2 1 7 1x21 T5 PCA 1x21 39 T5 ECO Ip x tec 8 1 5 9 2 4 2 5 2 5 1 6 2x21 T5 PCA 2x21 39 T5 ECO Ip x tec T2 3 6 4 4 2 5 1 5 1 5 1x39 1x40 T5 TC L PCA 1x21 39 T5 ECO Ip x tec 7 0 6 2 5 5 4 7 1 1 0 7 2 1 1 4 1 5 1 0 1 3 0 9 2x39 TS PCA 2x21 39 T5 ECO Ip x tec 5 3 4 0 2 5 8 0 6 0 9 1x28 1S PCA 1x28 54 T5 ECO Ip x tec 9 74 3 93 3 39 2 68 2 52 2 44 2x28 TS PCA 2x28 54 T5 ECO Ip x tec 10 0 7 3 V7 2 1 22 1 9 1x54 T5 PCA 1x28 54 T5 ECO Ip x tec 5 6 35 1 5 6 qa 1 3 2x04 T5 PCA 2x28 54 T5 ECO Ip x tec 8 9 8 5 1 4 5 0 7 0 7 1x35 T5 PCA 1x35 49 80 T5 ECO Ip x tec 9 1 6 0 4 2 2 2 1 9 1 8 2x35 T5 PCA 2x35 49 T5 ECO Ip x tec 8 7 7 2 1 4 4 1 4 0 9 1x49 T5 PCA 1x35 49 80 T5 ECO Ip x tec 9 6 7 8 4 3 8 1 0 1 0 2x49 15 PCA 2x35 49 T5 ECO Ip x tec 7 8 7 5 0 6 d 0 6 0 7 1x80 T5 PCA 1x35 49 80 T5 ECO Ip x tec 8 1 7 8 1 6 0 6 0 5 0 6 2x80 T5 PCA 2 80 T5 ECO Ip 6 8 5 4 4 1 0 8 0 8 0 7 2 TR DO N C Data sheet 09 11 839 3 We reserve the right to make technical changes without prior notice Electronic ballasts for dimming to 1 Linear lamps T5 16mm high efficiency high output Dimming Dimming curve is adapted to the eye sensitiveness Dimming range 1 to 10
8. 4 T5 TC L PCA 2x14 24 T5 ECO Ip x tec 400 V 400 V 1x21 T5 PCA 1x21 39 T5 ECO Ip x tec 400 V 2x21 15 PCA 2x21 39 T5 ECO Ip x tec 400 V 1x39 1x40 T5 TC L PCA 1x21 39 T5 ECO Ip x tec 400 V 400 V 2x39 T5 PCA 2x21 39 T5 ECO Ip x tec 400 V 1x28 T5 PCA 1x28 54 T5 ECO Ip x tec 430 V 2x28 T5 PCA 2x28 54 T5 ECO Ip x tec 430 V 1x54 i5 PCA 1x28 54 T5 ECO Ip x tec 430 V 2x54 T5 PCA 2x28 54 T5 ECO Ip x tec 430 V 1x35 T5 PCA 1x35 49 80 T5 ECO Ip x tec 430 V 2x35 TS PCA 2x35 49 T5 ECO Ip x tec 430 V 1x49 T5 PCA 1x35 49 80 T5 ECO Ip x tec 430 V 2x49 TS PCA 2x35 49 T5 ECO Ip x tec 430 V 1x80 15 PCA 1x35 49 80 T5 ECO Ip x tec 430 V 2x80 T5 PCA 2 80 T5 ECO Ip 430 V Installation instructions Wiring type and cross section The wiring can be solid cable with a cross section of 0 5 to 0 75 mm for push terminal and 0 5 mm for IDC terminal For the push wire connection you have to strip the insulation 8 9 mm wire preparation 0 5 0 75 mm 8 9 mm Loosen wire through twisting and pulling TRIDONIC Wiring advice The lead length is dependent on the capacitance of the cable Ballast Terminal Maximum capacitance allowed Type Cold Hot Cold Hot PCA 1 xx T5 ECO Ip x tec 1 12 9 10 200 pF 100 pF PCA 2 xx T5 ECO Ip x tec 11 12 13 14 9 10 15 16 200 pF 100 pF With standard solid wire 0 5 0 75 mm the capacitance of the lead is 30 80 pF m This value is influenced by the way the wiring is made Lamp connecti
9. 5 PCA 2x28 54 T5 ECO Ip xitec 0 42A 0 38A DC operation 1x35 T5 PCA 1x35 49 80 T5 ECO Ip xtec 0 14A 0 13 A 220 240 V 0 Hz 2x35 T5 PCA 2x35 49 T5 ECO Ip xitec 0 26A 0 24A 198 280 V OHz certain lamp start 1x49 T5 PCA 1x35 49 80 T5 ECO Ip x tec 0 18A 017A 176 280 0 Hz operating range 2x49 T5 PCA 2x35 49 T5 ECO Ip x tec 0 36 A 0 33 A Use in emergency lighting installations according to 1x80 T5 PCA 1x35 49 80 T5 ECO Ip x tec 0 30 A 0 27 A EN 50172 or for emergency luminaires according 2x80 T5 PCA 2 80 T5 ECO Ip 0 79A 0 72A to EN 61347 2 3 appendix J Ballast lumen factor AC operation AC BLF EN 60929 8 1 Emergency units wattage lamp Ballast AC BLF at The PCA T5 ECO Ip x tec ballasts are compatible W type type Un 230 Vac with all emergency units from TridonicAtco See the 1x14 T5 PCA 1x14 24 T5 ECO Ip xitec 1 00 table in the data sheet Also all 5 pole emergency 2x14 T5 PCA 2x14 24 T5 ECO Ip xitec 0 99 units can be used When used with other emergency 4x24 1x14 T5 TC L PCA 1x14 24 T5 ECO Ip xtec 4 01 1 04 units tests are necessary 2x24 2x24 T5 TC L PCA 2x14 24 T5 ECO Ip x tec 1 02 1 02 1x21 15 PCA 1x21 39 T5 ECO Ip xttec 1 03 2x21 15 PCA 2x21 39 T5 ECO Ip xitec 1 02 Temperature range 1x39 1x40 T5 TC L PCA 1x21 39 T5 ECO Ip x tec 1 02 0 97 Unlimited dimming range from 10 C to ta max 2x39 T5 PCA 2x21 39 T5 ECO Ip xitec 1 02 25 C to 10 C
10. Electronic ballasts for dimming to 1 Linear lamps T5 16mm high efficiency high output T5 TCL PCA T5 ECO Ip x tec 14 80 W 220 240V 50 60 0 Hz or Ki digital 1 gt RA dimming o je re 100 apie I te OT Ts side fixing feature side fixing feat e world first first processor controlled ballast with x tec inside e operation of T5 lamps of the same length e g FH 28 W FQ 54W e automatic lamp detection and operation with correct lamp parameters e average service life 50 000 h at ta max with a fee getty oo e operating frequency 40 100 kHz Packaging e integrated SMART interface 360 mm housing e Intelligent Voltage Guard overvoltage box of 10 indication and undervoltage pro e Intelligent Temperature Guard overtemperature protection e automatically triggered emergen ection cy 76 boxes pallet 760 pieces pallet 425 mm housing Pr eS gt Certified EN 55015 EN 55022 EN 60929 EN 61000 3 2 EN 61347 2 3 EN 61547 failure rate lt 0 2 per 1 000 operating hours light value for DC and rectified AC voltage box of 25 Suitable for emergency e dimming range from 1 100 e SMART Heating Concept for optimum filament heat 33 boxes pallet installations according e lamp
11. ation and functionallity of profiles see user manual Operating voltage S 3 Intelligent Temperature Guard Intelligent Voltage Guard The intelligent temperature guard protects the Intelligent Voltage Guard is the name of the new PCA T5 ECO Ip x tec from thermal overheating by electronic monitor from TridonicAtco This innovative reducing the output power or switching off in case of feature of the PCA family of control gear from operation above the thermal limits of the luminaire or TridonicAtco immediately shows if the mains voltage ballast Depending on the luminaire design the ITG rises above or falls below certain thresholds Measures operates at about 5 to 10 C above Tc temperature can then be taken quickly to prevent damage to the control gear e f the mains voltage rises above approx 305V voltage depends on the ballast type the lamp starts flashing on and off e This signal demands disconnection of the power supply to the lighting system e The active current control of these control gears is protected against failure caused by the high mains currents generated as a result of mains undervolt age The switch off level depends on lamp wattage and is typically lt 140V Wattage W lamp Ballast type type Uout 1x14 T5 PCA 1x14 24 T5 ECO Ip x tec 400 V 2x14 5 PCA 2x14 24 T5 ECO Ip x tec 400V 1x24 1x14 T5 TC L PCA 1x14 24 T5 ECO Ip x tec 400 V 400 V 2x24 2x2
12. e corridorFUNCTION is wrongly activated in a switchDIM system for example a switch is used instead of pushbutton there is the option of installing a pushbutton and deactivating the corridorFUNCTION mode by five short pushes of the button within three seconds switchDIM and corridorFUNCTION are very simple tools for controlling ballasts with conventional momentary action switches or motion sensors To ensure correct operation a sinusoidal mains voltage with a frequency of 50 Hz or 60 Hz is required at the control input Special attention must be paid to achieving clear zero crossings Serious mains faults may impair the opera tion of switchDIM and corridorFUNCTION Energy saving PCA T5 ECO Ip x tec mains power in 100 90 80 _ 70 60 50 40 _ 30 _ 20 10 o E sss 100 90 80 70 60 50 40 30 201510 5 4 3 2 1 dimming level in Backwards compatibility With a simple key combination a PCA T5 ECO Ip x tec can be reset as a normal PCA ECO from the previous generation Synchronisation simply has to take place three times within one minute 3x 105s To activate the x tec settings again synchronisation has to take place four times within one minute u u fi l z if switchDIM PCA T5 ECO Ip x tec DSI PCA T5 ECO Ip x tec Dimmable ballasts from TridonicAtco have to be earthed Automatic circuit breaker type C10 C13 C16 C20 B10 B
13. ilure This applies to AC and DC operation valid at 100 light output single wattage ballast corridoPFUNCTION V1 power consumption in standby mode lt 0 8W Data sheet 09 11 839 3 We reserve the right to make technical changes without prior notice TR DO N IC Electronic ballasts for dimming to 1 Linear lamps T5 16mm high efficiency high output Lamp starting characteristics Mains currents in DC operation at 70 light output Warm start Starting time 0 5s with AC wattage lamp Ballast Mains current at Mains current at Starting time 0 2 s with DC w type type Un 220 Voc Un 240 Voc Start at any dimming level 1x14 T5 PCA 1x14 24 T5 ECO Ip xtec 0 06 A 0 06 A 2x14 T5 PCA 2x14 24 T5 ECO Ip xitec 012A 042A 1x24 1x14 T5 TC L PCA 1x14 24 T5 ECO Ip xitec O10 A 0 10A 0 09A 0 09A AC operation 2x24 2x24 T5 TC L PCA 2x14 24 T5 ECO Ip xttec 0 20 A 0 20A 0 18 A 0 18 A Mains voltage 1x21 T5 PCA 1x21 39 T5 ECO Ip x tec 0 09 A 0 08 A 220 240 V 50 60 Hz 2x21 T5 PCA 2x21 39 T5 ECO Ip x tec 0 17 A 016A 198 264V 50 60 Hz including safety 1x39 1x40 T5 TC L PCA 1x21 39 T5 ECO Ip xtec 0 15A 0 15A 044A 0 14A tolerance 10 2x39 T5 PCA 2x21 39 T5 ECO Ip x tec 0 30A 0 28 A 202 254 V 50 60 Hz including performance 1x28 T5 PCA 1x28 54 T5 ECO Ip x tec 011A 011A tolerance 6 8 2x28 T5 PCA 2x28 54 T5 ECO Ip x tec 0 21 A 0 20 A 1x54 T5 PCA 1x28 54 T5 ECO Ip xitec O 21A 0 20A 2x54 T
14. on should be made with symmetrical wiring Hot leads 9 10 15 16 and cold leads 11 12 13 14 should be separated as much as possible When using two or more dimmable ballasts in one luminaire with separate dimming controls the lamp leads must be kept separate Dimmable ballasts from TridonicAtco have to be earthed Data sheet 09 11 839 3 We reserve the right to make technical changes without prior notice Electronic ballasts for dimming to 1 Linear lamps T5 16mm high efficiency high output O control signal o leads 9 10 keep wires short max 1 0 m leads 11 12 max 2 0 m ballast must be earthed digital signal DSI or switchDIM PCA T5 ECO Ip x tec 1x14 80W RFI e Connection to the lamps of the hot leads must be kept as short as possible e Mains leads should be kept apart from lamp leads ideally 5 10 cm distance e Do not run mains leads adjacent to the electronic ballast e Twist the lamp leads e Keep the distance of lamp leads from the metal work as large as possible e Mains wiring to be twisted when through wiring e Keep the mains leads inside the luminaire as short as possible General advise Electronic ballasts are virtually noise free Magnetic fields generated during the ignition cycle can cause some background noise but only for a few milliseconds Oo control signal O leads 9 10 15 16 keep wires short max 1 0 m leads 11 12 13 14 max
15. the two wire bus is according to the appropriate low voltage regulations switchDIM Integrated switchDIM function allows a direct connection of a push to make switch for dimming and switching Brief push lt 0 6 s switches ballast ON and OFF The ballasts switch ON at light level set at switch OFF When the push to make switch is held PCA ballasts 1 SMART LS II Ip article number 86458258 Loading of automatic circuit breakers Dimming characteristics PCA T5 ECO Ip x tec digital dimming value 255 225 200 175 150 125_ 100 ___ 75 50 25 DSI i 0 10 20 30 40 50 60 70 80 90 100 relative lighting level in Dimming characteristics as seen by the human eye are dimmed After repush the PCA is dimmed in the opposite direction The switchDIM fade time is set to 3s from min to max in the factory settings With a 20s push to the push to make switch this fade time can be changed to 6s In this instance the switchDIM application will be synchronized to 50 light level after 10s and after 20s the light level rises to 100 with the new fade time At every synchronizsation 10s keystroke the device will reset to 3s factory setting In installations with PCAs with different dimming levels or opposite dimming directions e g after a system extension all PCAs can be synchronized to 50 dimming level by a 10s push Use of push to make switch with indicator lamp is not permitted Deactivation If th
Download Pdf Manuals
Related Search