MPS Hi-Low Seating System Assembly Guide
Contents
1. Adjustments cont Cushions Back and headrest cushions adjust up Headrests and down along the center track MHS and MHL headrests fit MS and ML shells MHS Standard MHL w Laterals 7 W x 6 H Back Cushions MS2 MS4 and ML2 back cushions fit MS shell ML2 and ML4 back cushions fit ML shell MS2 MS 4 ML2 MLA 8 W x 8 5 H c 9 W x 11 H 10 W x 11 H 11 W x 13 H Seat Cushions MS seat cushions fit MS shell ML seat cushions fit ML shell MS5 MS7 10 W x 12 D 12 W x 12 D 13 W x 15 D Hip Flex adjustment provides a range of positions between 15 of hip flexion and 15 of hip extension Cushions can be cleaned with warm water and mild detergent Do not submerge 11 Adjustments cont Always secure child in the restraint 5 Point Harness Chest amp Shoulder Nie ed cis e Always keep child in view Proper adjustment of the harness is important for both e Secure straps tightly positioning and safety of the child Please consult your therapist to ensure the 5 point harness is properly adjusted for the child To facilitate transfer unclip the chest harness in the middle and allow the harness to open out To change the width of the chest harness adjust the center chest strap and set to the desired width A To change the length of the lower shoulder straps adjust the strap lengths both sides B To tighten the upper shoulder harness pinch an2. 1 Attaching the MPS seat to the Hi Low Base Hardware Bag 2 A On a flat surface Place the MPS Seat face down as shown Then roll the Hi Low Base up to the MPS shell and align the mounting bracket holes as shown Top Down View Hi Low Base MPS Shell face down B C Install nylon spacers on Hi Low mounting Match mounting bracket holes Install bracket mounting bolts as shown securely tighten hex bolts 05 2 Attaching the Tilt Piston to the MPS seat A It is recommended that a second person assists with this part of the assembly process Lock all casters on the base Position tilt piston axle midway through the tilt piston head B Rotate the MPS seat shell until tilt piston axle keys into seat pan Helpful Tools allen key Small crescent wrench not included Hardware Bag 4 oot C Slide tilt piston bolt with first washer installed through the MPS seat pan metal tabs and the tilt piston axle Then install second washer and lock nut as shown D Using allen key and wrench tighten lock nut and hex bolt securely 06 3 Installing the Footrest Parts Needed Hardware ee ef A P Velcro facing in on footrest leg extensions A Using the star shaped rubber knobs secure the footrest leg extensions into the MPS shell Hepeat on opposite side B Finished Use the round shaped rubber knobs to Enjoy using your Special Tomato M
3. For Small Hi Low part is a bolt For Large Hi Low part is a nut CLOSE UP SHOULDER STRAP ADJUSTMENT MECHANISM INSTALLED REVERSE PROCESS TO RETHREAD 14 Regular Product Maintenance We recommend the following daily product inspections Ensure all adjustment knobs and bolts are secure Check all harness pads and Velcro for signs of wear and tear Verify all casters move freely and lock securely Ensure the tilt piston attachment hardware is securely tightened O A C N hardware is securely tightened 6 Ensure the 5 point harness is securely fastened around the child and functions properly 7 Ensure pelvic harness attachment hardware is tight and securely fastened 8 Ensure the up down foot pedal and up down foot pedal lock are functioning properly 9 Ensure the tilt lever and tilt lever lock are functioning properly Cleaning How to Maintain When cleaning we recommend using a mild non abrasive detergent cleaner to wipe the chair periodically 5 point amp pelvic harness pads The harness pads can be removed hand washed at 38 C or 100 F then air dry Seat back and headrest cushions Wipe with warm water and or mild detergent Do not submerge Always ensure product is dry before use To extend the life of the hook and loop strips comb out the hook portion hard side to remove lint and other debris Ensure the MPS seat shell and Hi Low base attachment
4. MPS Hi Low Seating System Assembly Guide Model Series 79300105 amp 79300305 UMHLMO3 15LIT CAUTION Read Instructions Before Using Save This Guide For Future Reference This product is NOT a certified car seat iP For Customer Service Support Contact your dealer directly Before Contacting Customer Service Support Please fill in the following We will be able to help you more quickly if you have the exact information indicated Serial number Notice The information contained in this document is subject to change without notice No part of this document may be photocopied reproduced transmitted transcribed stored in a retrieval system or translated to another language or computer language in any form or by any means electronic mechanical magnetic optical chemical manual or otherwise without the prior written consent of Bergeron Health Care Use only Special Tomato accessories and parts on Special Tomato products Special Tomato parts are not interchangeable with other manufacturers products Replace any worn parts immediately for safety Located on back of seat shell 2015 Bergeron Health Care All rights reserved 01 The MPS Hi Low Seating System has been designed to offer affordable seating and positioning while providing optimal comfort and function This manual shows how to easily and safely take advantage of the features this product offers Contents O3 Safet
5. PS Hi Low install the footrest support as shown Seating System Hepeat on opposite side 07 4 Installing the Tray optional Parts Needed Velcro facing out Hardware o o o A Using round rubber knob bolts and washers install the tray supports as shown above Repeat on opposite side B Secure the tray surface by folding the Velcro tabs over the tray supports as shown Be sure to fully engage Velcro 08 Locks Using Caster Locks Level position is unlocked Down position is locked Adjustments Tilt in Space Lever Unlocked Locked To prevent serious injury always verify that the tilt amp up down pedal locking pins are fully engaged before you place the child in the seating system Using Tilt Lever amp Up Down Pedal Locks Pull and rotate pin 90 to Pull and rotate pin 90 in disengage lock the opposite direction to engage lock Up Down Pedal The tilt in space angle can be adjusted while the child is in the seat Before adjusting the tilt in space angle of the seat be sure the child is securely fastened in the 5 point harness To adjust the tilt angle A Grip foam push handle firmly B Release the lock mechanism on the tilt lever C While firmly gripping the foam push handle push the tilt lever down to adjust the tilt position D Select the desired tilt angle E Return the tilt lever to locking position F Re engage the tilt lever lock to secure th
6. connection If any parts should fail please stop using the product and contact customer service or your local dealer 15 Dimensions Small MPS Seat Cushions Large MPS Seat Cushions MPS Seat Specifications ML3 ML5 ML7 Target User Age 9 mos 5 yrs 6 9 yrs 8 11 yrs 10 14 yrs 12 Adult Target User Height Don Oe gt EES Zoos 48 62 58 Adult Maximum User Wt 130 lbs Seat Width HON ee Seat Depth 10 15 Seat to Footrest 6 16 8 18 Hip Flex Angle 15 to 15 15 to 15 Seat Tilt Angle Forward Seat Tilt Angle Back Floor to Seat Ht 14 28 5 17 28 5 Small MPS Back Cushions Large MPS Back Cushions Tray Specifications MPS Back Specifications MS2 MS amp ML2 ML amp Dimensions DIENEN Target User Age Qmos 3yrs 2 9yrs 6 9 yrs 8 Adult Weight 8 lbs Target User Height Mee MR Fy SY 48 Adult Maximum User Wt 80 lbs 130 lbs Back Width 8 9 104 11 Back Height 8 5 11 11 15 Top of Back Cushion 11 16 15 20 15 20 19 22 Top of Head Cushion 18 23 21 26 24 28 20 30 16 Consumer Information Limited Warranty Please fill out and mail your warranty card Bergeron Health Care warrants to the original retail purchaser of the Special Tomato product that if any part or component proves defective in material or workmanship within 5 years of
7. d pull the spring loaded shoulder harness mechanism located on the back of the seating system and pull the shoulder harness loop away from the seat To loosen pinch and pull the spring loaded shoulder harness mechanism and simply pull the foam chest harness forward away from user 5 Point Harness Pelvic To facilitate transfer press the center button to unlock the pelvic restraint All three pelvic straps are length adjustable to properly secure the child 12 Hi Low Harness QS Threading amp Connections Strap Diagram Harness Installed CHEST STRAPS LATERAL STRAPS BOLTED UNDERNEATH SEAT PAN UNCLIP ALL HARNESS STRAP BUCKLING 3 POINT CROTCH HARNESS WAIST amp CROTCH STRAP BOLTED UNDERNEATH SEAT PAN 3 Point Belt Removal 1 Unscrew the two strap anchor bolts shown LAP STRAP ON INSIDE CHEST HARNESS ON OUTSIDE 2 Unclip crotch strap from D ring anchor 3 Reinstall bolts for safekeeping REVERSE PROCESS TO RETHREAD 13 Hi Low Harness Threading amp Connections cont Shoulder Strap Removal 1 Unscrew top part of vertical bar on left side only 2 Slide up left side of shoulder strap adjustment mechanism off the vertical bar 3 Reinstall top part of left vertical bar 4 Unscrew top part of vertical bar on right side only 5 Slide up right side of shoulder strap adjustment mechanism off the vertical bar 6 Reinstall top part of right vertical bar
8. e seat The up down height can be adjusted while the child is in the seat Before adjusting the up down height of the seat be sure the child is securely fastened in the 5 point harness To adjust the up down position A Disengage the foot pedal lock B Grip foam push handle firmly with both hands C Step on the up down foot pedal D Select the desired height E Remove your foot from the up down foot pedal F Re engage the foot pedal lock 09 Adjustments cont Tray Tray angle and depth can be adjusted To adjust the tray tilt loosen round To adjust the tray depth disengage Velcro tabs knob and reposition the tray support and reposition the tray to the desired depth angle on both sides then re engage Velcro on both sides Footrest To adjust the footrest to desired To adjust footrest depth three bolt To position the user s feet in the height and angle loosen round hole locations allow for adjustment footrest secure the Velcro straps rubber knobs on both sides and Remove round knob hardware and provided so the foot is held in reposition the Velcro Tighten the reposition footrest to desired depth place The straps should be round knobs to set the footrest Re install round knob hardware and placed over the bridge of the foot position To adjust the depth of tighten securely above the toes the legrest extension remove star shaped knobs and reposition to desired depth Re install the star shaped knobs 10
9. her children To prevent tipping Do not attempt to move the seating system over uneven surfaces Use care when transferring children in and out of the seating system Always put the seating system at the lowest position when moving a child around their environment Only use this product on a level surface All 4 caster locks must be engaged at all times during use When adjusting the height and tilt angle of the seating system always use the push handle Never use the tray for this purpose When steering and moving the seating system from one area to another only use the push handle Never use the tray for this purpose Always check that locking knobs and bolts are tightened and secure at all times Regular maintenance is required to make sure this product remains in good working condition Never use abrasive cleaners The product is made for indoor use only Always secure child in the restraint e Never leave child unattended e Always keep child in view e Secure straps tightly e Always use seating system on a smooth level surface 03 Unpack your MPS Hi Low Seating System Check Parts Carefully remove them from the boxes and check all the parts you have ordered Once you have checked all the components you are then ready to assemble the MPS Hi Low Seating System and attach it to its base WARNING Keep plastic bags away from children 04 Assembly allen key Large
10. the purchase date MPS Seat shell or Soft Touch cushions 2 years of the purchase date All other parts and components The defective part will be repaired or replaced at Bergeron Health Care s discretion free of charge Warranty service may be performed by an authorized service center or at Bergeron Health Care s discretion the factory This warranty does not cover normal wear and tear or damage caused by accident or misuse To exercise this limited warranty the user should first obtain a Return Authorization Number from the dealer the Special Tomato product was purchased from The product must be delivered charges pre paid UPS recommended to the factory or to an authorized service center together with a copy of the original invoice the Return Authorization Number and a written description of the problem For Customer Service Support Contact your dealer directly tomato 2015 Bergeron Health Care All rights reserved
11. y Information O4 Unpack your MPS Hi Low Seating System 05 Assembly Attaching the MPS seat to the Hi Low Base 06 Assembly Attaching the Tilt Piston to the MPS seat 07 Assembly Installing the Footrest 08 Assembly Installing the Tray 09 Locks 09 Adjustments Tilt in Space Up Down Activity Tray Footrest Cushions 5 Point Harness 13 Harness Threading amp Connections 15 Regular Product Maintenance 15 Cleaning 16 Seat Dimensions 17 Consumer Information 02 Safety Information Always read instructions fully before use To improve safety we recommend that users should not be left unattended at any time while using Special Tomato equipment Only use Special Tomato approved components with your product Never modify the product in any way Failure to follow instructions may put the user or caregiver at risk and will violate the warranty on the product If any parts should fail please stop using the product and contact customer service or your local dealer Be sure that all adjustments are securely fastened before you put the user into the product Always secure the 5 point harness after transferring the child into the seating system When the product is stationary be sure that all casters are locked and facing outward from the base Especially when the tilt function is being used When the seat is in use be sure that the height and tilt adjustment lockouts are engaged to prevent accidental adjustment from ot
Download Pdf Manuals
Related Search