ATV30BRGB USER MANUAL
Contents
1. Thank you for purchasing this AUDIO SYSTEMS ATV30BRGB All Terrain Sound System Please read through these instructions carefully so you will know how to operate your model properly After you have finished reading the instructions keep this document in a safe place for future reference USER MANUAL QUICK START GUIDE ATV30BRGB THIS PACKAGE CONTAINS 1 ATV30BRGB All Terrain Speaker System 1 Bluetooth Multi Function Controller 1 Handlebar Mounting Kit 1 RF RGB LED Remote w CR2032 Battery 1 Quick Connect Power Extension Adaptor 4 Hi strength Nylon Mounting Straps 1 User Manual Quick Start Guide Poster 1 Warranty Card INFORMATION TO THE USER J Bluetooth The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG Inc and any use of such marks is under license Other trademarks and trade names are those of their respective owners GETTING STARTED BLUETOOTH ENABLED ALL TERRAIN SOUND SYSTEM GETTING TO KNOW YOUR ATV30BRGB LED RF CONTROLLER USING THE REMOTE CONTROL e When use for the first time pull out the film protruding the tray e RF controller range Up to 25ft LoS e Do not obstruct the RF remote with metal e Always keep away from small children e Do not store in direct sunlight e Do not submerge in mud and or water INSTALLING THE BATTERY e Slide the tray out2. VOLUME CONTROL 5 To raise the volume Press and Hold the VOL button 2 3 seconds 6 To lower the volume Press and Hold the 3 VOL button 2 3 seconds All rights reserved No part of this publication may be reproduced distributed or transmitted in any form or by any means including photocopying recording or other electronic or mechanical methods without the prior written permission of AVA Enterprises Inc To ES a Make sure your device headphone volume is set at 75 level before stowing Tips PRINTED IN CHINA 0815 VER 1 0 EN ATV30BRGB UM POSTER STYLE FINAL v1 0 indd 2 INFORMATION TO THE USER FCC COMPLIANCE STATEMENT This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of this device This transmitter must not be co located or operated in conjunction with any other antenna or transmitter The Bluetooth antenna cannot be removed or replaced by user This equipment complies with FCC IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency RF Exposure Guidelines and RSS 102 of the IC radio frequency RF Exposure rules This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation MPE
3. WIRE DIAGRAM Align arrows Mini DIN Connector QUICK RELEASE POWER ADAPTOR INCLUDED Fuse is located inside the power adaptor Turn counter clockwise to open lt 4 z Replace with 15A AGC Fuse type only POWER ADAPTOR OPTIONAL DIRECT BATTERY WIRING CIRCUIT 20A Recommended 12 14ga Wire not included BATTERY Chassis ground point Fuse and fuse holder not included Normally open switch not included BLACK Chassis N ground point A Metal frame _ SPECIFICATIONS BLUETOOTH Version 3 0 w EDR A2DP Range 33ft 10m Class 2 7 95 OG BOSs Q 202mm ia SPEAKERS 909 O 11 58 294mm li Tweeter Size 1 PEI SOFT DOME AMPLIFIER Maximum Output Power 450 Watts Input impedance 10kQ Frequency Response 45Hz 25kHz Dimensions 6 5 i NJ LA Q BOSS 0 Impedance 40 Cone Type PP CARBON RUBBER SURROUND 28 50 724mm GENERAL Operational Power 14 4VDC 10 16V allowable MAX Current Draw 13 7A Replacement Fuse 15A AGC TYPE Color Blac
4. But it is desirable that it should be installed and operated keeping the radiator at least 20 cm or more away from person s body excluding extremities hands wrists feet and ankles Alteration or modifications carried out without appropriate authorization may invalidate the user s right to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are de signed to provide reasonable protection against harmful interference in a residen tial installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guar antee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Relocate or reorient the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help CAUTION ADJUSTMENT OR ALTERATIONS OF THI
5. Using this product without running the engine can drain the battery MULTI FUNCTION CONTROLLER MOUNTING MULTI FUNCTION CONTROLLER UNIT LOCK NUT ALLEN HEAD BOLT Z BRACKET SNAP BRACKET COCK NUT ALLEN HEAD WASHER BOLT HANDLEBAR CLAMP LEFT or RIGHT RUBBER SHIM Pa FOR ILLUSTRATION PURPOSES YOUR VEHICLE MAY VARY TOOLS NEEDED 12mm Socket Wrench or Pliers 6mm Allen Wrench GETTING STARTED GETTING TO KNOW YOUR 1 MFC MULTIFUNCTION CONTROLLER 2 BLUETOOTH INDICATOR LED BLUE COLOR 3 POWER INDICATOR LED RED COLOR 4 3 5mm AUX INPUT 5 PREVIOUS TRACK Press and hold for VOL 6 PLAY PAUSE Press and hold for POWER ON D NEXT TRACK Press and hold for VOL STREAMING MUSIC a MULTIFUNCTION CONTROLLER BLUETOOTH OPERATION 1 Press the PLAY PAUSE once to start playing music or press the PLAY button from your device touch screen 2 To skip songs or advance press the NEXT TRACK button 3 To select the previous song press the PREVIOUS TRACK button VOLUME CONTROL 4 To raise the volume Press and Hold the VOL button 2 3 seconds 5 To lower the volume Press and Hold the VOL button 2 3 seconds Make sure your device Bluetooth volume is set at 75 level before stowing Tips
6. on back of the remote control and insert battery with the and minus poles pointing in the proper direction A RF CONTROLLER USER MANUAL ATV30BRGB BLUETOOTH ENABLED ALL TERRAIN SOUND SYSTEM POWER ON OFF MODE UP AUTO DEMO LONG PRESS FOR SINGLE COLOR MODE WITH RF RGB LED REMOTE CONTROLLER eet BRIGHTNESS UP BRIGHTNESS DOWN MODE DOWN COLOR DOWN COLOR UP REPLACEMENT BATTERY CR2032 10 SPEED DOWN AUX INPUT ATV30BRGB can play audio from any device that has a 3 5mm headphone audio jack YOUR DEVICE MULTIFUNCTION CONTROLLER AUX IN OPERATION 1 Power on the ATV30BRGB by pressing and holding down the PLAY PAUSE multi function button for 3 seconds 2 Disconnect any paired Bluetooth device by turning off Bluetooth in your devices Settings Menu 3 Connect the integrated 3 5mm AUX IN cable located on right side of the MFC to your devices headphone jack 4 Route the wire back to ATV30BRGB secure your device in a safe posistion 30S AUDIO SYSTEMS BOSS Audio Systems 3451 Lunar Court Oxnard CA 93030 www bossaudio com 805 751 4853 Tech Support www bossaudio com technical support lelC X FE iPod iPhone are trademarks of Apple Inc registered in the U S and other countries Android is a trademarks of Google Inc registered in the U S and other countries BOSS Audio Systems is not affiliated with Apple Inc or Google Inc
7. S DEVICE MAY RESULT IN HAZARDOUS RADIATION EXPOSURE a PAIRING amp DISCOVERING A NEW BLUETOOTH CONNECTION 1 Power on the ATV30BRGB by pressing and holding down the Play Pause multi function button for 3 seconds the blue and red LEDs will start to alternately flash signalling that the ATV30BRGB is now ready for Bluetooth pairing NOTE You have 2 minutes before you must restart this procedure over again 2 Now that the ATV30BRGB is in pairing mode ANDROID users Go into the Settings Menu of your device Enter the Bluetooth Menu TURN ON Bluetooth and press SCAN ATV30BRGB will now be displayed under AVAILABLE DEVICES If prompted enter passcode 0000 09Qandcoy iOS users a Go into the Settings Menu of your iOS device b Enter the Bluetooth Menu c TURN ON Bluetooth d ATV30BRGB will now be displayed e If prompted enter passcode 0000 3 If the ATV30BRGB is not seen repeat the above steps to refresh the Device List 4 When the connection is successful you are now ready to stream music from your favorite media player to the ATV30BRGB BEFORE INSTALLING THIS PRODUCT To avoid potential shorts in the electrical system be sure to disconnect the bat tery cable before installation Use this unit with a 12 Volt battery and negative ground ing only Failure to do so may result in a fire or
8. equipment while driving a motorized vehicle safe driving and safety consideration of others should always be your highest priority m In the event you should notice smoke strange noises or odor from this product or any other abnormal signs immediately turn off the power and consult your dealer or the nearest authorized BOSS AUDIO Service Center Using this product in this condition may result in permanent damage to the system m Set your volume control at a low setting then slowly increase the sound until you can hear it comfortably without distortion or ear discomfort a BE SURE TO OBSERVE THE FOLLOWING GUIDELINES Do not turn up the volume so high that you can t hear what s around you Use caution or temporarily discontinue use in potentially hazardous situations INSTALLATION PRECAUTIONS WARNING Always consult a professional installer Do not attempt to install or service this product by yourself Installation or servicing of this product by persons without professional training and experience in electronic equipment and motorized vehicle accessories may be dangerous and could expose you to the risk of electric shock injury or other hazards m Refer any repairs to a qualified BOSS AUDIO SYSTEMS Service Center m The ATV30BRGB can be powered from a vehicles cigarette lighter auxiliary power port or hard wired directly to the battery through an optional relay accessory switch m When wiring directly to the vehic
9. k Weight 14 26lbs 6 47Kg Dimensions cm WxHxD 72 4 x 20 2 x 29 4 Dimensions Inches WxHxD 28 50 x 7 95 x 11 58 Storage Temperature 5 F to 113 F 15 C to 45 C Operation Temperature 14 F to 140 F 10 C to 60 C SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE 7 31 2015 6 24 57 PM
10. les battery be sure to disconnect the batteries negative terminal wire before starting any wiring procedures it is suggested that an optional fuse and fuse holder not included with minimum rating of 20 Amps be in line with the positive battery terminal m The ground cable length should not exceed 18 inches See wiring diagram m The ATV30BRGB has a weather resistant design it should not be submerged in or under water under any circumstances m Use only the installation parts provided with the ATV30BRGB A CAUTION Using other mounting methods may void this warranty BLUETOOTH OPERATION O O BOSS on RECONNECTION 1 Power on the ATV30BRGB and your last paired device Bluetooth 2 The unit will now automatically reconnect 3 If your device was previously paired with the ATV30BRGB but it wasn t the last paired device a Ensure no other devices are currently paired b Enter the Bluetooth Menu on your device being paired c ATV30BRGB will display under AVAILABLE DEVICES d Choose the ATV30BRGB to reconnect 4 If the device is out of range from the ATV30BRGB it will disconnect automatically a To reconnect once device is back in range press the D Play Pause button once b The ATV30BRGB will now reconnect to the device To avoid battery exhaustion be sure to occasionally run the vehicles engine while using this product
11. malfunction CAUTION RISK K Nor s NEL When replacing the fuse be sure to only use a fuse of the rating specified on this product To avoid short circuiting cover any disconnected leads with insulating tape It is especially important to insulate any unused wires which if left uncovered may cause a short circuit When connecting other devices to this product refer to the manual for the product to be connected The black cable is ground make sure to connect the ground wire first Ensure that the ground wire is properly connected to metal parts of the vehicles body frame or direct to the battery if your vehicle does not have a grounded chassis frame The ground wire of this units power amp and a second powered system must be connected to the frame separately with different screws If the screw for the ground wire loosens or falls out it could result in fire or malfunction SPEAKER MOUNTING SUGGESTIONS Route strap around the speaker body to vehicle frame Route strap through the hole and to vehicle frame Route strap through the hole and to vehicle frame CAUTION Mounting straps should be double checked to be sure they are pulled tight and secure before each use of the vehicle BEFORE YOU START IMPORTANT SAFETY PRECAUTIONS m Do not operate mobile
Download Pdf Manuals
Related Search