INSTEON LED Bulb 2672
Contents
1. 0 90 relative humidity non condensing 240 Volts AC 1096 50 60 Hz NO Yes all saved in non volatile EEPROM 0 75 Watt CE C Tick 23 Troubleshooting LED Bulb won t link to other INSTEON Devices Your LED Bulb may be out of range of other INSTEON Devices or a large appliance may be generating electrical noise disrupting the INSTEON signal Try this e Check to make sure your LED Bulb is not connected to a dimmer If so remove the dimmer or relocate LED Bulb to a non dimming fixture e Try relocating your LED Bulb to see if linking can be accomplished If linking works normally in another area of the house consider adding additional INSTEON devices to extend and strengthen your network e Some home appliances like refrigerators televisions and speaker docks may produce excessive electrical noise If you ve recently added a new electronic device to your home unplug it and try linking again If LED Bulb links normally add a powerline noise filter to the problematic appliance LED Bulb is slow to respond This issue most likely lies with the controller not your LED Bulb the controlling device is probably repeating commands not being acknowledged by an INSTEON device that has been removed from the network The repeated commands are slowing down the INSTEON network resulting in a delayed response from the LED Bulb Try this e Consider if you have removed any INSTEON devices from your network that were part of the sl2. 26 Product Warranty Limited Warranty Seller warrants to the original consumer purchaser of this product that for a period of two years from the date of purchase this product will be free from defects in material and workmanship and will perform in substantial conformity to the description of the product in this Owner s Manual This warranty shall not apply to defects or errors caused by misuse or neglect If the product is found to be defective in material or workmanship or if the product does not perform as warranted above during the warranty period Seller will either repair it replace it or refund the purchase price at its option upon receipt of the product at the address below postage prepaid with proof of the date of purchase and an explanation of the defect or error The repair replacement or refund that is provided for above shall be the full extent of Seller s liability with respect to this product For repair or replacement during the warranty period call 866 243 8022 with the Model and Revision of the device to receive an RMA and send the product along with all other required materials to INSTEON AT TN Receiving 16542 Millikan Ave Irvine CA 92606 5027 Limitations The above warranty is in lieu of and Seller disclaims all other warranties whether oral or written express or implied including any warranty or merchantability or fitness for a particular purpose Any implied warranty including any warranty of merc
3. Dual Band Hamp Rate On Level INSTEON Link Linking Unlinking Multi Linking Unlinking Factory Reset Load On Off Retry Scene Set Button Simulcast X10 INSTEON Glossary The INSTEON transmitter The INSTEON receiver LED turning on and off repeatedly An INSTEON device that can send and receive both INSTEON powerline signals and INSTEON radio frequency signals The speed at which the load fades on or off The preset brightness level a device will return to when turned on A dual band mesh networking technology developed by INSTEON The world s most reliable expandable and simple home automation and control technology A one way association between a controller and responder A method for associating INSTEON controller buttons with groups of INSTEON responders such that the responders instantly return to a memorized state when the button is pushed Links can be made manually with the set button or using software The process by which an INSTEON device can remove stored links Just as with linking unlinking is a one way process and should be performed in both directions for devices that are both controllers and responders of each other as in a 3 way switch scenario A special mode that allows more than one link to be either created or removed simultaneously without laborious set button presses When in linking or unlinking mode an INSTEON device will continue to link to other devices until the set butt
4. INSTEON INSTEON LED Bulb Owner s Manual Contents Getting Started INSTEON LED Bulb Device Overview Do Not Connect to a Dimmer Leave Your Fixture On Linking INSTEON Links Understanding Linking Linking to the INSTEON Hub using the iOS or Android App Linking with a Single Button Controller Linking with a Multi Button Controller Multi Linking or Making a Scene Unlinking from a Single Button Controller Unlinking from a Multi Button Controller Multi Unlinking or Removing a Scene Software Only Features Ramp Rate Disable Linking on Power up Always On Wiring Always On Wiring Appendix Specifications Troubleshooting Certifications and Warnings Product Warranty 10 11 12 19 14 16 18 22 24 25 2 Getting Started Everything you need to quickly get up and running INSTEON LED Bulb Device Overview INSTEON ID b f WEE TES Z f Leave Your Fixture On If your switch is OFF communication with the L ED Bulb is lost ATP Emm wu mi 060 a f your fixture is controlled by a wall switch consider wiring as always on Do Not Connect to a Dimmer INSTEON LED Bulb dims using INSTEON commands e Linking Your LED Bulb does not have a set button To link manually unscrew the LED Bulb for a moment and reinsert INSTEON Links INSTEON devices can stand alone and function as a local switch or dimmer but their real power comes when
5. ains important information for users with regards to the proper disposal and recycling of INSTEON products Consumers are required to comply with this notice for all electronic products bearing the following symbol Environmental Information for Customers in the European Union Furopean Directive 2002 96 EC requires that the equipment bearing this symbol on the product and or its packaging must not be disposed of with unsorted municipal waste The symbol indicates that this product should be disposed of separately from regular household waste streams It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities Correct disposal and recycling will help prevent potential negative consequences to the environment and human health For more detailed information about the disposal of your old equipment please contact your local authorities waste disposal service or the shop where you purchased the product DECLARATION OF CONFORMITY TO R amp TTE DIRECTIVE 1999 5 EC for the European Community Switzerland Norway Iceland and Liechtenstein Product category general consumer category 3 20 Certifications and Warnings English This equipment is in compliance with the essential requirements and other relevant provisions of the European R amp TTE Directive 1999 5 EC Deutsch German Dieses Ger t entspricht den grundlegenden Anfo
6. d hold the set button until the device beeps P Your INSTEON controller will now control your LED Bulb Make sure your fixture is On and then screw in the LED Bulb Your LED Bulb will double beep 10 Multi Linking or Making a Scene On your INSTEON controller press and hold the set button until the device beeps then tap the set button am DO One at a time screw in your LED Bulbs For other devices press and hold the set button until they double beep KR m Adjust your scene members to their desired state on off or brightness level if dimming 50 72 Y LED Bulb LED Bulb 30 ON E Lamp 3 Appliance Tap the set button on your INSTEON controller to finish building your scene m 2 Your INSTEON controller will now control your scene Du Unlinking from a Single Button Controller Press and hold the set button again until the device beeps On your INSTEON controller press and hold the set button until the device beeps Make sure your fixture is On and then screw in the LED Bulb Your LED Bulb will double beep A V WE un 2 f n P Your INSTEON controller will no longer control your LED Bulb 12 Unlinking from a Multi Button Controller Press and hold the set button again until the device beeps On your INSTEON controller tap the desired control button and then press and hold the set but
7. e Le present appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autorise aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radiolectrique subi mme si le brouillage est susceptible d en compromettre le fonctionnement CAUTION To reduce the risk of overheating and possible damage to other equipment do not install to control a receptacle a motor operated appliance a fluorescent lighting fixture or a transformer supplied appliance Gradateurs commandant une lampe a filament de tungstene afin de reduire le risqu de surchauffe et la possibilite d endommagement a d autres materiels ne pas installer pour commader une prise un appareil a moteur une lampe fluorescente ou un appareil alimente par un transformateur DECLARATION OF CONFORMITY Hereby INSTEON declares that this device is in compliance with the essential requirements and other relevant provisions of the following Directives 1 Electromagnetic Compatibility Directive 2004 108 EC 2 Hazardous Substance Directive 2005 95 EC Technical data and copies of the original Declaration of Conformity are available and can be obtained from INSTEON 16542 Millikan Ave Irvine CA USA User Information for Consumer Products Covered by EU Directive 2002 96 EC on Waste Electric and Electronic Equipment WEEE This document cont
8. hantability or fitness for a particular purpose which may not be disclaimed or supplanted as provided above shall be limited to the two year of the express warranty above No other representation or claim of any nature by any person shall be binding upon Seller or modify the terms of the above warranty and disclaimer Home automation devices have the risk of failure to operate incorrect operation or electrical or mechanical tampering For optimal use manually verify the device state Any home automation device should be viewed as a convenience but not as a sole method for controlling your home In no event shall Seller be liable for special incidental consequential or other damages resulting from possession or use of this device including without limitation damage to property and to the extent permitted by law personal injury even if Seller knew or should have known of the possibility of such damages Some states do not allow limitations on how long an implied warranty lasts and or the exclusion or limitation of damages in which case the above limitations and or exclusions may not apply to you You may also have other legal rights that may vary from state to state Protected under U S and foreign patents see www insteon com patents Copyright 2013 INSTEON Rev 07 18 14
9. on is tapped or four minutes have elapsed whichever occurs first A process that erases all stored links and reconfigures the device to factory defaults The device that you are controlling e g a light bulb ceiling fan etc A device that can control its connected load to turn on and off but cannot dim Usually a relay based device A 2nd or subsequent attempt by a controller to send an INSTEON signal usually after an acknowledge is not received from the responder in the expected time slot Multiple devices respond to memorized states For example a dinner time scene turns on the dining table light dims the kitchen lights to 1096 backyard lights turn off and the thermostat adjusts to 72 A button on an INSTEON device that is used for setting or changing its properties A method for increasing the reliability of message delivery in a network When a node in a network sends a message every other node that hears the message retransmits it at precisely the same time based on a global clock provided that the message has not already been retransmitted some maximum number of times Message propagation is more robust because each node adds its energy to the signal much like voices in a choir Simulcasting is much simpler than message routing because there are no routing tables to maintain and nodes can join the network without any installation procedure A legacy powerline networking technology Many INSTEON devices are backwards com
10. ow to respond scene If so the links to these devices need to be removed from the controller Use software to examine the database of the controller or if you know the modules that were removed manually remove their links using the standard unlinking procedure e f you are unable to identify the missing devices perform a factory reset on the controller This will remove all links from the controllers database but will also require that you reconfigure the device s scenes and properties LED Bulb turned on or off by itself Most likely a device somewhere in the house has been linked to your LED Bulb Try this e AsLED Bulb automatically enters linking mode every time it is powered on it is possible to accidentally link a device to LED Bulb in the brief period of time that the Bulb is in linking mode You can use software like HouseLinc to examine LED Bulbs links to find the stray connection want to factory reset my LED Bulb Because LED Bulb lacks a set button there is no manual way to factory reset LED Bulb Try this e Using software like HouseLinc manually remove all of the device links 24 Certifications and Warnings This device complies with FCC Rules and Industry Canada license exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference including interference that may cause undesired operation of the devic
11. patible with X10 devices by setting a house and unit code 21 Specifications General Brand INSTEON Key Application Low energy remote control lighting Product Number 2672 522 AUS NZ Edison Screw 2672 5382 AUS NZ Bayonet UPC 813922013658 AUS NZ E27 813922013665 AUS NZ B22 Patent Protected under US and Foreign Patents See www insteon com Warranty INSTEON Features INSTEON RF RF Frequency patents 2 years limited Yes 921 0 MHz AUS NZ INSTEON PowerLine Yes INSTEON Controller No INSTEON Responder Yes Number of Responder Groups 400 Responder Commands Supported On Off Fast On Fast Off Begin Brighten Begin Dim End Brighten End Dim Maximum INSTEON Links X10 Compatible Programming Lock Incremental Brighten Beep 400 Yes Yes Incremental Dim 22 Operation Lumens Lumens per Watt Color Rendering Index Color Temperature Status LED On Levels Ramp Rate Mechanical Installation Color Dimensions Weight Operating Environment Operating Temperature Range Operating Humidity Range Electrical Supply Voltage Local Control All Settings Saved Through Power Outage Power Consumption Certification Specifications 991 66 83 90 2 00 K None 32 0 125 seconds to 8 minutes software only E2 Medium Edison screw base B22 Bayonet base White 2 8 diameter 4 7 length 72mm diameter 119mm length 6 2 OZ 176g Indoors 32 to 104 F 0 to 40 C
12. rderungen und den weiteren entsprechenden Vorgaben der Richtlinie 1999 5 EU Nederlands Dutch Dit apparaat voldoet aan de essentiele eisen en andere van toepassing zijnde bepalingen van de Hichtlijn 1999 5 EC Svenska Swedish Denna utrustning star verensst mmelse med de v sentliga egenskapskrav och vriga relevanta bestammelser som framgar av direktiv 1999 5 EG Francais French Cet appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la Directive 1999 5 EC Espanol Spanish Este equipo cumple con los requisitos esenciales asi como con otras disposiciones de la Directiva 1999 5 CE Portugu s Portuguese Este equipamento est em conformidade com os requisitos essenciais e outras provis es relevantes da Directiva 1999 5 EC Italiano Italian Questo apparato conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva 1999 5 CE Norsk Norwegian Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i EU direktiv 1999 5 EF Suomi Finnish T m laite tyttaa direktiivin 1999 5 EY olennaiset vaatimukset ja on siin asetettujen muiden laitetta koskevien maaraysten mukainen Dansk Danish Dette udstyr er i overensstemmelse med de vaesentlige krav og andre relevante bestemmelser i Direktiv 1999 5 EF Polski Polish Urzadzenie jest zgodne z og lnymi wymaganiami oraz szczeg lnymi warunkami okreslonymi Dyrektywa UE 1999 5 EC
13. rolled by a wall switch you might consider wiring that wall switch as Always On so that flipping the switch will not disconnect LED Bulb from power Replacing the wall switch with an INSTEON Switch will provide full control for any INSTEON device in your home Always On Wiring Turn off power to your switch at the Remove the old switch and electrical service panel disconnect the wires If your box lacks neutral wires stop and contact support A Neutral Wire C ae Circuit Breakers Fuse Panel Connect the Micro Module wires to the identified wires in the junction box Verify that the wire nuts are secure and that no exposed copper wire is visible except for the bare ground wire Load NS Neutral L e Load L1 Line L e INSTEON 18 Always On Wiring Unscrew and reinsert your LED Bulb for a moment and reinsert Your LED Turn on power at the circuit breaker panel To link your Micro Module to the LED Bulb press and hold the set Bulb will double beep button until the device beeps z A W p Test your switch Your LED Bulb will turn on and off Turn off power and place the Micro Module in the junction box followed by the switch Turn power on to the switch at the circuit breaker panel J Your switch will now control eva LED BUD 19 Appendix Everything else you might need to know about your INSTEON product Controller Hesponder Blinking
14. t they each control one another and the connected load Cross Linking is necessary Responder Only Some devices cannot control other devices these devices only receive INSTEON commands b 639 W 2 LED Bulb Micro Module Some devices can only link as responders to devices and scenes Use Cross Linking To Cross Link simply turn on the devices and perform the linking process twice once in each direction Link Switch A to Switch B and repeat to link Switch B to Switch A Linking to the INSTEON Hub using the iOS or Android App e From Rooms navigate to All Devices amp O72 8 O Select LED Bulb from the list of devices Add Device LED Bulb Thermostat Door Sensor t o Open Close e Tap the Add button All Devices Add Back Doo Bathroom Garage Doo sor Outside Lights gt O72 4 When prompted turn on your fixture and screw in the LED Bulb The Bulb will double beep Me Z You can now control your LED Bulb from the INSTEON Hub Linking with a Single Button Controller On your INSTEON controller press Make sure your fixture is On and and hold the set button until the then screw in the LED Bulb Your device beeps LED Bulb will double beep VA Your INSTEON controller will now control your LED Bulb Linking with a Multi Button Controller On your INSTEON controller tap the desired control button and then press an
15. they are connected together to form a control system Most INSTEON devices can control one another and be the recipient of control The process of associating multiple INSTEON devices to one another is called linking Understanding Linking Links are One Way When linking INSTEON devices the links that are created are one way Switch A will turn Switch B on and off but Switch B cannot turn Switch A on or off Controllers INSTEON devices that can turn other devices on or off are called controllers lt lt lt gt O 0 T I gt N gt oO lt Sensors Switches Remotes and the Hub are common controllers Links Remember a Device s State The current state of the controlled device is stored in the link on off or dimmed Switch Lamp Dimmer The switch will turn on the Lamp Dimmer to 75 brightness Responders INSTEON devices that receive the command of a controller are called responders Thermostats LED Bulbs Plug In Modules and In Line Modules are common responders Understanding Linking Controller Only Some devices like sensors can only control other devices Motion Sensor Micro Module The Motion Sensor will turn on the Switch but the switch cannot control the Motion Sensor Grouping Devices You may want to group together two devices for example in a virtual three way configuration For INSTEON this is called cross linking To mirror Switch A and B so tha
16. ton until the device beeps a Vv Vv C Vv AN I a Make sure your fixture is On and then unscrew and reinsert the LED Bulb Your LED Bulb will double beep lt lt S3 PES gt lt gt lt T R T M Aet Your INSTEON controller will no longer control your LED Bulb 13 Multi Unlinking or Removing a Scene On your INSTEON controller press and hold the set button until the One at a time unscrew and reinsert your LED Bulbs For other device beeps Press and hold the devices press and hold the set set button again then tap the set button until they double beep button E EI Lo Tap the set button on your INSTEON controller to exit Multi Unlinking mode ddd J Your INSTEON controller will no longer control your INSTEON devices 14 Software Only Features Most INSTEON devices contain features that can only be enabled disabled or modified using INSTEON control software such as HouseLinc and an INSTEON PowerLine Modem Software Only Features Ramp Rate Customize the speed at which the LED Bulb fades on or off Default is 0 5 seconds maximum duration of 8 minutes 0 5 Seconds Disable Linking on Power up Prevents LED Bulb from entering linking mode each time power is disconnected and reapplied Default is off e Ay v 16 Always On Wiring Because LED Bulb needs constant power if you have a light fixture that is cont
Download Pdf Manuals
Related Search