bubble arch, foam curtain installation manual
Contents
1. Picture 4 0 Assembles the Frame Motor City Wash Works Inc 48285 Frank Wixom Michigan 48393 U S A Phone 248 313 0272 Fax 248 313 0271 8MANLFOMARCHO0001 REV 1 1 www motorcitywashworks com 3 Position the frame with the driver side LEG OUTSIDE EDGE 45IN away from the INSIDE EDGE of the CONVEYOR INSIDE GUIDE RAIL Secure the frame to the floor using 72 X4 1 2 wedge anchor bolts Level the arch as shown below and shim under the base plate if needed Picture 5 0 Level The Arch L Secure the head assembly on wood boards and removes the four crossbeam clamp see Picture 6 0 Lift the head assembly toward the entrance side of the arch and using the four clamps secure the head assembly to the 4X4 arch crossbeam see picture 7 0 Do not tighten the clamps to the beam yet O Centers the head assembly onto the crossbeam slowly drop the head assembly from the lifting device This will allow the head to hang from the fasteners insuring that the head will be level when the fasteners are tightened Then tighten the clamps to the beam Open the front door and unroll down the vinyl strip 4 CLAMPS WASH ENTRANCE WOOD BOARDS gt Picture 6 0 Remove the Clamps Picture 6 1 Raise the Head Assembly Motor City Wash Works Inc 48285 Frank Wixom Michigan 48393 U S A Phone 248 313 0272 Fax 248 313 0271 8MANLFOMARCHO0001 REV 1 1 www motorcitywashworks com 42. Picture 7 0 Secure the Clamps to the Beam BUBBLE ARCH Utilities Installation L Locate the optional dilution station and secure it to a solid wall at least 40 inches above the floor see Picture 48 0 This will allow for sufficient room for a 55 gallons chemical drum to be position under the dilution station without interfering with its operation Secure the optional control box close by Pull hose 3 4 from fresh water supply and connect to the dilution station inlet barb fitting see Picture 8 1 below Pull another 3 4 hose from the outlet barb fitting to the head assembly on driver side see Picture 29 0 TO HEAD ASSY DRIVER spp 3 4 RUBBER HOSE CONTROL BOX FROM FRESH WATER SUPPLY CHEMICAL DRUM Picture 8 0 Secure 401 from Floor Picture 8 1 Pull Hoses Motor City Wash Works Inc 48285 Frank Wixom Michigan 48393 U S A Phone 248 313 0272 Fax 248 313 0271 8MANLFOMARCHO0001 REV 1 1 www motorcitywashworks com 5 FROM DILUTION STATION 3 4 RUBBER HOSE CONNECT HERE Picture 9 0 Secure Hose to the Head Assembly Your Bubble Arch needs TWO FUNCTION OUTPUTS signals from your car wash controller One for the dilution station and one for the control box see Picture 10 0 The signal for the dilution station HAS TO BE OF THE SAME VOLTAGE THAN THE DILUTION STATION SOLENOID VALVE Verify the voltage of the dilution statio
3. H WASH WORKS Cri BUBBLE ARCH FOAM CURTAIN INSTALLATI ON MANUAL Part FOAMCURTOOOXXXX FOAMBUBLOOOXXXX TABLE OF CONTENT Equipment Utilities Page 1 Equipment Specifications ss Page 1 Bubble Arch Installation Page 2 Foam Curtain Instructions sss Page 10 Equipment Utilities FOAM CURTAIN ARCH BUBBLE ARCH FOAMCURTOOOXXXX FOAMBUBLOOOXXXX 115 VAC 1 PH 15AMPS 115 VAC 1 PH 15AMPS ELECTRICAL FLA 10AMPS FLA 10AMPS INCLUDING SIGN INCLUDING SIGN HYDRAULIC N A N A PNEUMATICS 10 SCFM Q 100 PSI MAX N A FRESH FRESH mes 5 GPM 40 PSI MAX 10 GPM Q 40 PSI MAX 2 OUNCES PER CAR AVERAGE 2 4 OUNCES PER CAR AVERAGE 120CPH 120CPH OUTPUTS CAR WASH 1 ONE FOR CONTROL PANEL ONE COR DIE CONTROLLER Equipment Specifications and Features Convenient 115VAC Single Phase Supply Minimize Installation Cost Oversized Back Lit Sign Customizable to your Request Compact Design Utilize only 3 0 of Tunnel Space Two Exiting foaming options Triple Foam and Single Foaming Bubble Arch Suggested Installation Tools and Materials OOOO V MEASURING TAPE L HAMMER DRILL WITH 1 2IN WEDGE ANCHORS BALL PEN HAMMER LEVEL WRENCHES ASSY LADDER SCREWDRIVERS ASSY SAFETY GOGGLES Motor City Wash Works Inc 48285 Frank Wixom Michigan 48393 U S A Phone 248 313 0272 Fax 248 313 0271 8MANLFOMARCHO0001 REV 1 1 www motorcitywashworks com 1 N
4. CCW DECREASE THE PUMP PRESSURE Picture 24 0 Dilution Station Pump Increase the air regulator gauge to value between 20 40PSI and go to the arch and notice foamer generator starting to foam Balance the foam generation between the three foam generators by opening or closing the air supply ball valves mounted on each generator Motor City Wash Works Inc 48285 Frank Wixom Michigan 48393 U S A Phone 248 313 0272 Fax 248 313 0271 8MANLFOMARCHO0001 REV 1 1 www motorcitywashworks com 14 FOAMER GENERATOR BALL VALVE Picture 25 0 Ball Valve Observe the foam generated You may change the concentration of the solution by adjusting the pressure of the pump or changing the injector tip Finally turn the output off and program the ready signal output to turn ON slightly before the car reaches the arch Test with a car Color Skinz Wrap Installation L Locate the boxes containing the COLOR SKINZ wraps and install on each legs and frame cross beams SELECT THE PROPER COLOR SKINZ COVER SNAP ONE SIDE OF THE LIPS SLIDE THE COVER AROUND THE LEG AND FINALLY SNAP THE SECOND LIP PASSED THE EXTRUSION EDGE see Picture 9 Skinz Picture 26 1 Picture 26 2 Color Skin
5. Color adjustable Strobe Three Color Gradual Speed is Change adjustable Seven Color Brightness is not Gradual adjustable Change Picture 27 2 Color Chart Motor City Wash Works Inc 48285 Frank Wixom Michigan 48393 U S A Phone 248 313 0272 Fax 248 313 0271 8MANLFOMARCHO0001 REV 1 1 www motorcitywashworks com 16 Control Box Electrical Schematic 14AWG BLK 48AWG RED 120 1 mmm e 120 1 mmm 20 V PR1 12 p tL 14 2 M1 A1 Y Cmm P R A2 7 d 14AWG BLK 18AWG YLW 18AWG WHT em WaLNAN L nmm Ud m foe m Wi Ola g 2 e 8 aD lt d amp SI al lal Km m m Ie INSTALL FERRULES ALL WIRES UNLESS SPECIFIED OTHERWISE 2 s gt e My 7 Fant Pe A e A Picture 28 0 Control Box Electrical Schematic Optional Arch Light Kit Part ARCHLIGHTKITXXXX Electrical Specifications Eight KI eroe 24VDC Flasher Supply 120VAC 2A GOTO E 24 250V AC DC Suggested Installation Tools and Materials 2 3 16 Socket Head Allen Wrench L Wire Stripper and Wire Ties L 1 8 Socket Head Allen Wrench L 2 Conductors 14 AWG Low Voltage Cable 6 Step Ladder L Water Proof Wire Nuts Installation Procedures Upon receiving your
6. 8 313 0271 8MANLFOMARCHO0001 REV 1 1 www motorcitywashworks com 11 Run line from the CAR WASH CONTROLLER to the CONTROL BOX see Picture 19 0 TO WATER VALVE FROM CW CONTROLLER 24 240V AC DC TO AIR VALVE FROM ELEC PANEL TO WASH BAY LED LIGHTS JUNCTION BOX 120VAC 15AMPS Picture 19 0 Electrical Runs Run also a line from the 120VAC building sub panel to the CONTROL BOX and connect on a separate 15AMPS circuit Run a lines from the CONTROL BOX to the PUMP MOTOR the AIR VALVE and the WATER VALVE and connect like shown on the picture 19 0 Use a junction box to connect all the three components USE 14AWG WIRES ONLY Run a separate lines from the CONTROL BOX to the LED LIGHTS JUNCTION BOX mounted on the exit end of the head assembly see picture 2220 0 CONNECT LEDLIGHTS RUN HERE USE 16 AWG WIRES MIN Picture 20 0 Led Light J Box Motor City Wash Works Inc 48285 Frank Wixom Michigan 48393 U S A Phone 248 313 0272 Fax 248 313 0271 8MANLFOMARCHO0001 REV 1 1 www motorcitywashworks com 12 Connect the wires in the control box following the schematic on picture 21 0 FROM CAR WASH 24 240V CONTROLLER AC DC RUN TO ARCH INTO LED JUNCTION BOX ed van RUN TO TRIPLE FOAM WATER AND AIR SOLENOID VALVES RUN TO TRIPLE FOAM PUMP MOTOR 120VAC ONLY FROM 120VAC 15AMPS SEPARATE CIRCUIT Picture 21 0 Electrical Co
7. HE ARCH REQUIRES A SEPARATE 15AMPS 120VAC 1PH ELECTRICAL CIRCUIT TO AVOID EQUIPMENT MALFUNCTION DO NOT CONNECT ANY OTHER ELECTRICAL DEVICE ON THE SAME CIRCUIT FEEDING THE ARCH Run two separate lines from the CONTROL BOX to the wash bay one to the LED JUNCTION BOX and one to the BLOWER JUNCTION BOX see picture 11 0 CONNECT BLOWER CONNECT LEDLIGHTS UN HERE RUN HERE ARCH EXIT END Picture 11 0 Arch Junction Boxes Motor City Wash Works Inc 48285 Frank Wixom Michigan 48393 U S A Phone 248 313 0272 Fax 248 313 0271 8MANLFOMARCHO0001 REV 1 1 www motorcitywashworks com 7 Connect the BLOWER and the LED lights runs to each respective junction boxes using the connection diagrams below TO BLOWER MOTOR 9 101112 FROM CONTROL BOX USE 14 AWG WIRES USE 16 AWG WIRES MIN FROM CONTROL BOX Picture 12 0 LED Junction Box Picture 12 1 Blower Junction Box RUN TO ARCH INTO LED JUNCTION BOX PAYD FROM CAR WASH 24 240V CONTROLLER AC DC RUN TO ARCH INTO BLOWER JUNCTION BOX FROM 120VAC 15AMPS SEPARATE CIRCUIT Picture 13 0 Control Box Connection Diagram WARNING RUN TWO SEPARATE LINES FOR BLOWER AND LED LIGHTS DO NOT RUN THE WIRES IN THE SAME CONDUIT Motor City Wash Works Inc 48285 Frank Wixom Michigan 48393 U S A Phone 248 313 0272 Fax 248 313 0271 8MANLFOMARCHO0001 REV 1 1 www motorcitywashworks com 8 Starting Up
8. L DIAGRAMS Motor City Wash Works Inc 48285 Frank Wixom Michigan 48393 U S A Phone 248 313 0272 Fax 248 313 0271 8MANLFOMARCHO0001 REV 1 1 www motorcitywashworks com 18 Electrical Diagrams LED LIGHT NOTES ALL 120 VAC ELECTRICAL CIRCUIT MUST BE PROTECTED BY SEG ADJUST LASHING RATE ERE 120 VAC Aldd S N3MOd 24 OR 120VAC OR 24VDC FROM CONTROLLER CONNECTION DIAGRAM FOR LIGHTED ARCH ALWAY OFF AND FLASH ON and OFF WHEN POWERED BY IHE CAR WASH CONTROLLER Picture 28 0 Connection Diagram of Flasher Unit with Light Always OFF Motor City Wash Works Inc 48285 Frank Wixom Michigan 48393 U S A Phone 248 313 0272 Fax 248 313 0271 8MANLFOMARCHO0001 REV 1 1 www motorcitywashworks com 19 LED LICHT NOTES ALL 120 VAC ELECTRICAL CIRCUIT MUST BE PROTECTED BY G F C l ADJUST LASHING RATE ERE 120 VAC 120VA 24VAC DC OQ rc FLASHER UNIT FRONT VIE AlddNsS M3MOd 24 OR 120VAC OR 24NDC FROM CONTROLLER CONNECTION DIAGRAM FOR LIGHTED ARCH ALWAY AND FLASH OFF and ON WHEN POWERED BY THE CAR WASH CONTROLLER Picture 29 0 Connection Diagram of Flasher Unit with Light Always ON Warranty a
9. MANLFOMARCHO0001 REV 1 1 www motorcitywashworks com 10 WARNING IT IS IMPERATIVE TO SUPPLY THE DILUTION STATION SYSTEM WITH CLEAN DRY COMPRESSED AIR A ANY AMOUNT OF MOISTURE VAPORIZED OIL OR ANY OTHER IMPURITIES WITHIN THE MAIN AIR SUPPLY MAY AFFECT THE PERFORMANCE OF THE EQUIPMENT AND LEAD TO PREMATURE WEAR OR MAJOR DAMAGE TO THE FOAM CURTAIN ARCH DELIVERY SYSTEM OR ITS COMPONENTS L Pull three 1 2 O D air line from the pump injector outlets to the foamer generator located onboard of the arch see pictures 17 0 and 18 0 RED CHEMICAL YELLOW T FROM MECH ROOM BLUE CHEMICAL OMPRESSED AIR Picture 18 0 Arch Tubing View from Top Your FOAM CURTAIN ARCH CONTROL BOX needs SEPARATE POWER SUPPLY from the 120 220VOLT building electrical panel and ONE FUNCTION OUTPUT signals from your car wash controller The signal to the control box can be anything between 24 to 240 VOLTS AC or DC WARNING THE MATERIAL REQUIRED FOR CONNECTING THE ARCH IS THE CUSTOMER S RESPONSIBILITY ALL WORK HAS TO COMPLY WITH LOCAL AND NATIONAL CODES THE ARCH REQUIRES A SEPARATE 15AMPS 120VAC 1PH ELECTRICAL CIRCUIT TO AVOID EQUIPMENT MALFUNCTION DO NOT CONNECT ANY OTHER ELECTRICAL DEVICE ON THE SAME CIRCUIT FEEDING THE ARCH Motor City Wash Works Inc 48285 Frank Wixom Michigan 48393 U S A Phone 248 313 0272 Fax 24
10. MCWW Light Kit open the box and verify that you have all the required components and there is no damage to the equipment Verify also that you have all your installation material Motor City Wash Works Inc 48285 Frank Wixom Michigan 48393 U S A Phone 248 313 0272 Fax 248 313 0271 8MANLFOMARCHO0001 REV 1 1 www motorcitywashworks com 17 Picture 29 0 LED String Picture 29 1 Other LED String Picture 29 2 Flasher Unit L Locate the aluminum channels and secure to the arch legs see picture 27 0 OPTIONAL ROUND LED SIGN SIGN ALUM CHANNELS CONNECT INTO LEG Picture 30 0 LED Aluminum Channels Picture 30 1 LED String L Install the LIGHT STRING into the channels Pull the cord thru the opening Pull the cord thru the UTILITY HOLE located on the outside face of the leg Pull a 2 Conductors PVC Jacket 14 AWG Low Voltage Cable from the mechanical room to the arch pull the cable through the leg and connect to the LED string cord using WATER RESISTANT wire nuts see Picture 27 1 Finally install the leg Color Skinz Install the power supply in the Mechanical Room or a dry area of the wash close to a 120 VAC power outlet Install the flasher assembly close to the power supply Connect the cord end of the power supply to the flasher unit see Picture 26 2 and to the 2c 14 cable of the LED light kit following one of the next ELECTRICA
11. Your BUBBLE ARCH O Disconnect the 3 4 rubber feeding hose at the arch and turn the water ON to the Dilution Station Drop the Dilution Station chemical suction line into the chemical drum Set the PUMP DILUTION RATIO to about 300 1 Follow Instructions on the CHEMICAL PUMP user manual Turn the DILUTION STATION FUNCTION OUTPUT ON and let the water run until a solid column of chemical fills the chemical suction line up to the pump Let it run until the solution feeding the arch is visibly mixed with chemicals Turn the output function OFF Reconnect the hose to the arch and turn the dilution station ON again until the arch trough is filled with solution Verify that the float stop the flow of solution when reached float level Adjust the float height to keep the solution level close to the edge Leave the dilution station ON Picture 14 0 Head Assembly Float Valve Turn the CONTROL BOX BREAKERS ON close the cover and turn the ARCH OUTPUT FUNCTION ON and observe the READY LIGHT TURN ON see Picture 15 0 The blower is now running and the foam generated is flowing over the edge down onto the ground Observe the bubble generated and change the concentration of the solution by adjusting the chemical pump For thicker foam and bubbles increase the concentration of chemical For lighter foam decrease the concentration Finally turn both output off and program the ready signal output to turn ON slightly before the car re
12. aches the arch while the dilution station output get to be programmed to turn ON with the car and turned OFF after the car is away long enough to refill the trough with solution READY LIGHT Picture 15 0 Control Box Ready Light Motor City Wash Works Inc 48285 Frank Wixom Michigan 48393 U S A Phone 248 313 0272 Fax 248 313 0271 8MANLFOMARCHO0001 REV 1 1 www motorcitywashworks com 9 FOAM CURTAIN ARCH Utilities Installation O Locate the optional HP PUMP DILUTION STATION and secure it to a solid wall at least 40 inches above the floor see Picture 16 0 This will allow for sufficient room for a 55 gallons chemical drum to be position under the dilution station without interfering with its operation Secure the optional control box close by CHEMICAL DRUM CHEMICAL DRUM CHEMICAL DRUM Picture 16 0 HP Pump Dilution Station Pull a 1 2 hose from a fresh water supply and connect to dilution station inlet barb fitting see Picture 3117 0 below Pull a 3 8 O D air line tubing from compressed air supply and connect to the air solenoid valve inlet located under the pump wall frame see Picture 17 0 TO FOAM 1 2IN CURTAIN ARCH CLEAR TUBING FROM FRESH WATER SUPPLY 3 8IN O D BLACK TUBING FROM COMPRESSED AIR SUPPLY Picture 17 0 HP Pump Dilution Hose and Tubing Motor City Wash Works Inc 48285 Frank Wixom Michigan 48393 U S A Phone 248 313 0272 Fax 248 313 0271 8
13. n before wiring The signal to the control box can be anything between 24 to 240 VOLTS AC or D WARNING A WRONG VOLTAGE APPLIED TO THE DILUTION STATION WILL PERMANENTLY DAMAGE THE VALVE COIL AND MAY ALSO LEAD TO PERSONAL INJURIES FROM CW CONTROLLER CHECK VALVE VOLTAGE BEFORE CONNECTING FROM CW CONTROLLER TO WASH BAY X 24 240V AC DC jm BLOWER JUNCTION BOX FROM ELEC PANEL TO WASH BAY ED LIGHTS JUNCTION BOX 120VAC 15AMPS Picture 10 0 Electrical Runs Motor City Wash Works Inc 48285 Frank Wixom Michigan 48393 U S A Phone 248 313 0272 Fax 248 313 0271 8MANLFOMARCHO0001 REV 1 1 www motorcitywashworks com 6 WARNING THE MATERIAL REQUIRED FOR CONNECTING THE ARCH IS THE CUSTOMER S RESPONSIBILITY ALL WORK HAS TO COMPLY WITH LOCAL AND NATIONAL CODES Pull an electrical run from the car wash controller to the dilution station and connect the dilution station to a separate function output This set up will allow the dilution station to run and refill the arch after the car leaves the arch and the blower turned off YOU MAY CONNECT THE DILUTION STATION ON THE SAME OUTPUT FUNCTION THAN THE CONTROL BOX IF THE WATER PRESSURE FEEDING THE DILUTION IS SUFFICIENT TO KEEP UP WITH THE ARCH WHEN RUNNING Pull a second run from the car wash controller to the CONTROL BOX Run line from the 120VAC building sub panel to the CONTROL BOX and connect on a separate 15AMPS circuit T
14. nd Return Procedure Motor City Wash Works warrant this product to be free of defect in material and or workmanship for a period of one year from the date of the purchase by the customer from MCWW During the warranty period MCWW will at its discretion at no charge to the customer repair or replace this product if found defectives with a new or refurbished unit but not to include costs of removal or installation Any product returned to MCWW for warranty has to have a Return Material Authorization Number All shipping cost to MCWW is assumed by the customer This is only a summary of MCWW Limited Warranty Please communicate with MCWW for our complete warranty Prior to returning any product to MCWW the customer must call in for Return Material Authorization Number and a copy of our Return Material Authorization Form filled and completed The RMA number must be written clearly on the outside of the shipping package and copy of the form must be included in the package Motor City Wash Works Inc 48285 Frank Wixom Michigan 48393 U S A Phone 248 313 0272 Fax 248 313 0271 8MANLFOMARCHO0001 REV 1 1 www motorcitywashworks com 20
15. nnections Schematic Starting Up Your BUBBLE ARCH Disconnect the 1 2 rubber feeding hose at the pump and turn the water ON to flush the line Shut the water OFF and reconnect the hose Select an injector according to the CHEMICAL USAGE CHARTS below A TURQUOISE tip may use less chemical per car than using a PINK Using a PINK instead may use more chemical but may generates foam with more vivid colors when using triple foam for example CHEMICAL TIME CHEMICAL CHEMICAL COLOR USAGE EACH FOR 0 057 INJECTOR TURQUOISE Picture 22 0 Turquoise Tip Usage Chart Motor City Wash Works Inc 48285 Frank Wixom Michigan 48393 U S A Phone 248 313 0272 Fax 248 313 0271 8MANLFOMARCHO0001 REV 1 1 www motorcitywashworks com 13 CHEMICAL CHEMICAL USAGE PER CAR 3 COLORS TIP CHEMICAL TIME ON COLOR USAGE EACH FOR 0 057 PER INJECTOR COLOR Picture 23 0 Pink Tip Usage Chart L Turn the CONTROL BOX BREAKERS ON close the cover and turn the PUMP DILUTION STATION FUNCTION OUTPUT ON and observe the READY LIGHT TURN ON see Picture 15 0 The pump is now running Set the pressure on the gauge to about 100PSI see picture 24 0 Let the water run until a solid column of chemical fills all the chemical suction line up to the injectors Let it run until the solution feeding the arch is visibly mixed with chemicals TURNING THE SCREW CW INCREASES THE PUMP PRESSURE TURNING THE SCREW
16. otes and safety Symbols Where necessary important points will be highlighted in this manual using the following symbols NOTES PROVIDES FURTHER INFORMATION STOP PRECAUTION TO TAKE TO AVOID EQUIPMENT MALFUNCTION OR ERROR WARNING DANGEROUS SITUATION WHICH MAY CAUSE A EQUIPMENT DAMAGES PERSONAL INJURIES OR FATALITIES Always follow all Notes Warning and instructions Not doing so may have serious consequences on the overall performance of the washing equipment and or the safety of the people working on and with the equipment Installation Instruction for FOAM ARCHES Open all boxes and crates and verify that you have all the required components as well as all your installation material Locate where the arch will be installed and using the picture below verify that the area is sufficiently large for your new foam arch working envelope see Picture 1 0 Picture 1 0 Foam Arch Working Envelope Motor City Wash Works Inc 48285 Frank Wixom Michigan 48393 U S A Phone 248 313 0272 Fax 248 313 0271 8MANLFOMARCHO0001 REV 1 1 www motorcitywashworks com 2 ge Picture 2 0 Foam Arch Overall Dimensions Picture 3 0 Foam Arch Overall Height Assemble the frame like shown on Picture 4 0 below in the area where the arch will be installed and stand the frame up The fasteners are shipped secure to the leg top of the legs
17. z Picture 26 0 Col LED LIGHT REMOTE CONTROL L Your foaming arch comes with a set of LED WALL WASHERS mounted in the head cover see picture 327 0 The wall washer LED light patterns are controlled by a LED controller located in the CONTROL BOX see Picture 27 1 L Using the MODE button on either the LED controller in the control box or using the hand held remote unit you may change the pattern and the resulting color in which the three colors RED GREEN and BLUE will be lighting on the sign as well as the vinyl strip Use the BRIGHTNESS and the SPEED button as needed Motor City Wash Works Inc 48285 Frank Wixom Michigan 48393 U S A Phone 248 313 0272 Fax 248 313 0271 8MANLFOMARCHO0001 REV 1 1 www motorcitywashworks com 15 REMOTE LED CONTROL CONTROLLER Pa ec LED WALL WASHERS Picture 27 0 LED Wall Washer Picture 27 1 LED Controller LED COLOR SELECTION CHART Control Method Remote or LED Controller MODE Changes Patterns from 1 11 list below Picture 27 2 BRIGHTNESS B Increases LED brightness BRIGHTNESS B Decreases LED brightness SPEED S Increases LED Speed SPEED S Decreases LED Speed Solid Red Solid Blue Solid Purple Brightness is Solid Green adus able Speed is not Solid Yellow available Solid Cyan Solid White Three Color Strobe Speed and brightness are both Seven
Download Pdf Manuals
Related Search