Operation Manual 03/06/2008
Contents
1. PANINI GRILLS ELECTRICAL USER S MANUAL NS NS PRODUCTION YEAR Listed 3096790 AXIS EQUIPMENT MVP GROUP CORPORATION 5659 ROYALMOUNT MONTREAL QC CANADA 2 9 Tel 514 737 9701 Fax 514 342 3854 WWW mvpgroupcorp com WWW axis equipment com Published on 03 06 2008 VER 08 Page1 of 14 TABLE OF CONTENTS PAGE NR TOPICS COVER PAGE TABLE OF CONTENTS INTRODUCTION 1 2 3 eremo cco vasra o TRANSPORTING AND MOWNG INSTALLATION OFTHE APPLIANCE ewmosowo NC 14 NUM OPERATION OF THE APPLIANCE CLEAN UP AND MAINTENANCE WARRANTY CAUTION This appliance should only be used in facilities where standards local safety codes and regulations are followed 2 14 INTRODUCTION Dear User Thank you for purchasing our AXIS product and for your confidence in our company Our appliances are produced in compliance with international standards IMPORTANT Please read and ensure that all users read this manual in order to achieve the desired performance that you expect and to enable you to use this AXIS appliance for many years c Please read and ensure that your operation personnel read this user s manual carefully before installing and using the appliance The manual containing information about installation usage and maintenance2. must have prior authorization by the factory Exceptions to above warranty are A Damages resulting from shipping handling or abuse B Incorrect installation and or connections C Adjustments or calibration of any parts D Faults due to lack of regular maintenance or cleaning of any internal part s E Replacement of any wearable items such as accessories F Discoloration of any components due to chemical reaction MVP GROUP CORP STATES THAT THERE ARE NO OTHER WARRANTIES EXPRESSED OR IMPLIED THAT ARE NOT SET FORTH HEREIN AXIS SHALL ASSUME NO OTHER RESPONSIBILITY EITHER DIRECT OR NON DIRECT OR BE LIABLE FOR ANY OTHER OR ADDITIONAL LOSS OR DAMAGE WHETHER BEING DIRECT OR CONSEQUENTIAL AS A RESULT OF ITS EQUIPMENT The manufacturer reserves the rights to alter design and specifications without notice 14 14
3. of our product you purchased should be read carefully Please ensure that power supply connections to the appliance are already installed by qualified personnel according to local regulations before our authorized service arrive for any service work to this appliance If our authorized service determines that the necessary repair s to be done are a result of the faulty installation on your part the warranty shall not be covered f you do not have enough information please contact our customer service department either by phone at 1 514 737 9701 or e mail at service mvpgroupcorp com We expect you to have the best performance from our product 3 14 TECHNICAL DATA AXIS MODEL NO MAIN DIMENSIONS 20 0 x 17 5 x 14 25 x 14 25 x inches 10 5 11 00 us ELECTRICAL INPUT kW FREQUENCY Hz THERMOSTAT RANGE 122 572 122 572 CF PROTECTION CLASS NET WEIGHT POWER SUPPLY VOLTS 240 4 14 ELECTRICAL CIRCUIT DIAGRAM A J 33 L1 L200H1 L1 L200 H2 22 m 51 92 ON OFF switch T1 T2 H1 H2 Heating elements L2 Thermostat Power input lamp Thermostat lamp 5 14 MAIN DIMENSIONS mm AX PD AX PM 6 14 WARNING SIGNS GROUNDED CONNECTION A POWER OVER
4. HEAT POWER SUPPLY CONNECTIONS 240 V 60 Hz Model AX PD 120 60 Hz Model AX PM 7 14 SAFETY DETAILS The appliance should only be operated under an exhaust hood Any kind of flammable solid and liquid material cloths alcohol and derivatives petrochemical products wooden and plastic materials cutting blocks curtains etc should never be placed near the appliance Do not clean the appliance with a pressure hose This appliance should be installed in line with local regulations and only be operated in well ventilated places Please refer to the instructions before installing and operating the appliance c This appliance is designed for commercial use and should only be operated by personnel trained according to this manual n case of fire or flame in the area where the appliance is operated turn off the power and use a fire extinguisher Never use water to extinguish the fire 8 14 TRANSPORTING AND MOVING AAA E 4 9 Before moving the appliance disconnect the power supply 9 14 INSTALLATION OF THE APPLIANCE If this appliance is installed close to any wall partition furniture corative material etc the distance between should be a min of 6 ft if those are coated with fireproof heat insulating material the distance should be a minimum of 6 DO NOT install this appliance on any non
5. al and regular usage and operation for a period of one 1 year following the date of original installation If a defect in material s or workmanship is detected or found to exist within the stated period above Axis at its sole discretion shall either repair or replace any original equipment manufacturers part which has proven to fail within the machine providing that the equipment has not been altered or tampered with in any manner has been installed correctly as per the owners manual and maintained and operated in complete accordance with this manual The labor cost in terms of bench warranty to repair or replace any part proven to be defective as per above clause s shall be covered by Axis within the continental United States of America or Canada provided that prior authorization for this labor was approved by Axis the service work was performed by an authorized Axis service agency and that this agency installed an original and genuine Axis part in the machine Any repair work performed by a non authorized service depot remains the sole responsibility of the user and Axis will not be held responsible The installation of any generic part will not be valid and therefore will void this warranty All authorized labor coverage shall be limited to bench rates only Any supplemental hourly rates or charges such as transport weekends or emergency premiums remain the responsibility of the user Any charges exceeding those stated herein
6. amp will light Clean upper and lower grids of the grill with a cloth or sponge It is now ready to use Clean the device after disconnecting it from the power supply After each use grids should be cleaned Frying fats are collected in the grease tray located at the front Always clean and remove any grease collected in the tray after each usage After daily use disconnect the appliance from the power supply by turning the key to the 0 position 12 14 CLEAN UP AND MAINTENANCE 1 CLEANING Before before the power is switched on and after the first use and every subsequent use outer surface of the appliance should be completely cleaned up with sponge and liquid detergent and then wiped dry Grid surface should be smeared with liquid oil Do not use CHEMICAL CLEANING AGENTS like hydrochloric acid or abrasive cleaning agents 2 MAINTENANCE Periodic maintenance should be carried out by a technician It is recommended to carry out maintenance at least every 6 months depending on the frequency of use Otherwise grids will corrode Grids and fat tray MUST always be kept clean Never leave the grids of the device wet after cleaning with water etc 13 14 MANUFACTURERS LIMITED WARRANTY MVP Group Corporation Axis hereby warrants all new equipment bearing the name AXIS and installed within the continental United States of America or Canada to be free from defects in material and workmanship under norm
7. combustible surface It is strongly recommended that fire safety protection instructions are always observed All of the items mentioned below in connection with the installation of the appliance should be carried out by authorized service personnel appliance should be installed to operate in a level position Power supply connection of the appliance should be checked by an authorized electrician and it should be connected to a dedicated breaker in your electrical panel c Installation of the appliance should be with a ground connection 10 14 CONTROL BOARD A ON OFF SWITCH AND THERMOSTAT B POWER INPUT LAMP C THERMOSTAT LAMP 11 14 OPERATION OF THE APPLIANCE C 3 Before first use outer surface of the appliance should be wiped with a soft cloth soaked in warm water with soap NOTE The appliance should be operated by a qualified personnel knowing the safety rules and technical specifications and who has read the instruction manual Take the contact grill machine carefully out of its package Connect power source Yellow warning lamp will light indicating that the grill is connected Open top cover s after you place your appliance to its location Before operating the contact grill Smear upper and lower plates lightly with oil Turn the key on to position I Keep on turning the key to set the thermostat to the operating temperature 482 F green l
Download Pdf Manuals
Related Search