Command listing for RS-232, Ethernet and
Contents
1. Creation Date 11 Sep 06 D t P Technical Bulletin ADVANCED Ea ENERGY Command listing for RS 232 Ethernet and Profibus Rev date Rev for all Generators based on C3 Technology 30 Oct 06 A04 Host Data Bytes Response Description Data Bytes Command 25 Restores the current operation restore parameters to EEPROM as preset with presets the given number 0 to 9 es only SSR only E only T Filename SKB 0035 pdf pdf Author engineering Creation Date 11 Sep 06 Sets the desired pulsing mode Send one byte e 0 Pulsing off e 1 Internal pulsing e 2 External pulsing e 3 External pulsing inverted e 4 Enable internal pulsing by external pulsing input Read back with command 177 27 set pulsing mode remote Rotating KNOB enabled control Matchbox buttons disabled 4 RF ON OFF buttons disabled Rotating KNOB disabled Matchbox buttons enabled e 5 RF ON OFF buttons enabled Rotating KNOB disabled Matchbox buttons enabled e 6 RF ON OFF buttons disabled Rotating KNOB enabled Matchbox buttons enabled 7 RF ON OFF buttons enabled Rotating KNOB enabled Matchbox buttons enabled Sets partial remote control which enables partial front panel control e Bit 0 set RF ON OFF buttons enabled Bit 1 set Rotating knob enabled e Bit 2 set Matchbox buttons enabled It follows e 0 Buttons and Knob disabled e 1 RF ON OFF buttons enabled Rotating KNOB disabled Matchbox but2. generator Note This command is not available on generators with fixed frequency Read back with 187 Sets the RF frequency Send 4 byte representing the RF frequency Hertz The accepted value depends on the type of generator ER only Note This command is only available on generators with variable frequency Read back with command 178 Sets the parameters for frequency tuning Send three bytes least significant byte first Byte1 2 specify the maximum frequency in kHz the value is ignored in control mode 0 Byte 3 selects the control mode for FST 0 no FST Frequency as defined with command 18 e 1 integral phase positive e 2 integral phase negative 3 proportional phase positive e 4 proportional phase negative If FST is active mode 1 4 the frequency set by the 1 CSR only command 18 is used as minimum frequency limit Take care that this frequency is less than the maximum frequency before command 17 is used Filename SKB 0035 pdf pdf Author engineering Creation Date 11 Sep 06 Technical Bulletin Ac ADVANCED Command listing for ENERGY RS 232 Ethernet and Profibus for all Generators based on C3 Technology Command Description Sets the RF frequency Send 3 byte representing the RF frequency in 100 Hertz steps for 18 example 10000 1 MHz RF The accepted value depends on the type of generator frequency Profibus Note This command is only available on generators only with
3. 2 Ethernet and Profibus for all Generators based on C3 Technology Description Requests the amount of life remaining in the target you specify Send one byte representing the desired target number 1 4 The controller board returns the target life in kilowatt hours Note A decimal is implied for example 100 1 kWh Set with command 12 Reports User port analog voltage Set with command 30 Requests process status The controller board returns the packet arranged as follows 1st status byte e 0 Reserved e 1 Unassigned e 2 Recipe run is active e 3 Reserved 4 Reserved 5 Output power 0 Off 4 On e 6 RF on requested O Off 4 On e 7 Set point status 70 Within tolerance 1 Out of tolerance 2nd status byte e 0 End of target life 1 Reserved e 2 Reserved 3 Overtemperature e 4 Reserved e 5 Reserved e 6 Unassigned e 7 Interlock open 3rd status byte fault flags e 0 Reserved 1 Reserved e 2 Reserved Rev date 30 Oct 06 Host Data Bytes read active Requests the number of the active target target Set with command 11 ef Response Data Bytes 4 data bytes 4 8 bit values Filename SKB 0035 pdf Author engineering Creation Date 11 Sep 06 Technical Bulletin ADVANCED Ac ENERGY Command 162 read process status 163 report tuning control mode 164 read set point regulat
4. Technical Bulletin ADVANCED i Command listing for ENERGY RS 232 Ethernet and Profibus Rev date Rev 30 Oct 06 A 04 for all Generators based on C3 Technology Products Power Generators with C3 Technology made beginning of September 2002 Subject Command listing Commands as used with RS 232 Ethernet and Profibus Attention This Technical Bulletin is outdated and will not be updated anymore A current list of AE Bus Protocol commands can be found in the user manual Table 4 16 which is delivered on CD RO with every generator This list of commands is based on the AE Bus Protocol command structure and reflects the commands which are necessary to make use of a digital Interface such as the RS 232 Ethernet or Profibus Response Command Description Data Bytes Turns off RF output 1 Read back with command 162 CSR only Turns on RF output the unit must be in host control 1 mode CSR only Read back with command 162 Sets the regulation mode Send one byte indicating the desired mode 3 e 6 Forward power regulation 1 regulation 7 Load power regulation select e 8 External power regulation DC Bias VGSR ONY Note You cannot change modes while the unit is on Read back with command 154 Specifies the maximum forward power that can be delivered Send two bytes least significant byte first 4 representing the maximum forward power in watts This forward command is used to limit the forward power on extern
5. al ce only power limit power regulation Accepts a value of 5 of maximum power to maximum power Read back with command 169 Filename SKB 0035 pdf pdf Author engineering Creation Date 11 Sep 06 Technical Bulletin ADVANCED i Command listing for ENERGY RS 232 Ethernet and Profibus Rev date for all Generators based on C3 Technology 30 Oct 06 Host Data Response Command Description Bytes Data Bytes Specifies the output set point level for the selected regulation mode select regulation mode with command 3 Send two bytes least significant byte first representing the set point level in watts Accepts a value of 0 to maximum power or maximum external feedback value Note The set point must be less than the maximum output power Read back with command 164 8 set point CSR only z 7 11 Specifies which target is active Send one byte select Accepts a value of 0 to 4 ee l active Note If 0 is selected the no target life timer will count only target Read back with command 156 Specifies the external feedback value that corresponds to the maximum voltage on the User port Send three bytes least 9 significant byte first Bytes 1 and 2 specify the maximum maximum external feedback value in the range of 100 to16000 100 V external feedback Byte 3 not used only for compatibility Read back with command 171 to 16000 V Read back with command 157 Sets the target life in kilow
6. att hours of the specified roe only target Send five bytes least significant byte first 12 Byte 1 selects the target number 1 to 4 Bytes 2 ER only ese only settarget through 5 specify the target life in kWh life Note A decimal is implied for example Filename SKB 0035 pdf pdf Author engineering 100 1 kWh Sets the target life in kilowatt hours of the target which Creation Date 11 Sep 06 12 is active see command 11 Send three bytes least set target significant byte first life Note A decimal is implied for example only 100 1 kWh Profibus Read back with command 157 13 tuner control mode Sets the tuner control mode Send one byte 0 Manual mode 1 Automatic mode Note A match network must be connected to the generator Technical Bulletin ADVANCED i Command listing for ENERGY RS 232 Ethernet and Profibus Rev date Command 14 active control mode 17 frequency tuning parameters 18 RF frequency for all Generators based on C3 Technology 30 Oct 06 Host Data Bytes Response Data Bytes Description Sets the generator s active control mode Send 1 byte e 2 Host control e 4 User port analog control e 6 Local control front panel Note If you try to change the control mode while the unit is on the unit automatically switches off Read back with command 155 1 CSR only The accepted values depending on the type of
7. baud the selection value is 0 115200 couldn t be represented in 2 byte Read back with command 212 No function Sets reflected power parameters Send three bytes least significant byte first Byte 1 sets the time until RF is turned off in seconds Bytes 2 3 set the reflected power detection level in watts Note If the time is set to 0 the protection mode is turned off Read back with command 152 Technical Bulletin ADVANCED Command listing f AAC ENeRGY Be a Rev date Command RS 232 Ethernet and Profibus for all Generators based on C3 Technology 30 Oct 06 Host Data Bytes Response Data Bytes Description and Ethernet 93 set pulsing frequency 96 set pulsing duty cycle 111 initialize capacitors 112 move shunt capacitor position 119 Profibus reset explicit fault clear 122 move series capacitor position 128 supply type Sets the RF pulsing frequency Send 3 bytes least significant byte first representing the pulsing frequency in Hz Accepts a value of 1 to 100000 1 Hz to 1 100000 Hz But the value should not exceed the 3 CSR only specified maximum pulse frequency of the specific generator Read back with command 193 Sets the RF pulsing duty ON time in increments of 1 This value can range 1 from 1 to 99 Minimum ON time is 16 ps 2 eeRonly Read back with command 196 Moves capacitors of a connected match network to 1 minimum position CSR o
8. he set point and run time for the selected report recipe step For the recipe step the controller returns recipe step four bytes set point run time Bytes 1 2 represent the recipe step set point in watts Bytes 3 4 represent the recipe step run time in tenths Filename SKB 0035 pdf Author engineering Creation Date 11 Sep 06 Technical Bulletin ADVANCED C d listing f AT ARAN ommand listing for wee Command RS 232 Ethernet and Profibus for all Generators based on C3 Technology 30 Oct 06 Host Data Bytes Response Description Data Bytes of seconds Set with command 22 and 23 191 report recipe step ramp time 193 read pulsing frequency 196 read pulsing duty cycle 198 reports software revision level 205 read run time 212 report serial port address and baud 212 report serial port address and baud rate only Profibus and Ethernet Reports the ramp time for the selected recipe step For the recipe step the controller returns two bytes Bytes 1 2 represent the recipe step ramp time in tenths 1 4 of seconds Set with command 21 Requests the RF pulsing frequency The controller returns four bytes least significant byte first representing the pulse frequency in Hertz Set with command 93 Requests the duty cycle in ON time The controller board returns two bytes least significant byte first representing the duty cycle in percent on time Set with comma
9. ion mode 165 read forward power 166 read reflected power Command listing for RS 232 Ethernet and Profibus for all Generators based on C3 Technology Rev date 30 Oct 06 Response Description Data Bytes e 3 Unassigned 4 Reserved 5 Out of set point 6 Reserved 7 Reserved Ath status byte fault flags 0 Current limit 1 Reserved 2 PROFIBUS error e 3 Unassigned 4 unassigned 5 Extended fault status 6 Reserved e 7 CEX is locked 70 Unlocked 4 Locked Reports tuner control mode 0 Manual mode 1 Automatic mode Set with command 13 Requests output set point level set with command 8 and whatever method of output regulation has been selected set with command 3 The controller board retunes 3 bytes Bytes 1 2 represent the set point value Byte 3 reports the method of output regulation Requests a snapshot of forward power level at that instant The controller board returns two bytes representing the forward power in watts LSB first Requests a snapshot of reflected power level at that instant The control board returns two bytes representing the reflected power in watts LSB first 167 Requests a snapshot of load power level at that instant read The response contains 2 data bytes Both bytes Filename SKB 0035 pdf Author engineering Creation Date 11 Sep 06 Technical Bulletin ADVANCED i Command li
10. ll technical information contained is subject to changes without prior notice For recent updates please contact Customer Service Filename SKB 0035 pdf Author engineering Creation Date 11 Sep 06
11. motor movement Reports the motor movement The control board returns 1 byte e 0 Match network s motors stopped e 1 Match network s motors running Report on and off ramping rise and fall times The 151 controller board returns four bytes least significant byte report first ramping Bytes 1 2 represent rise time rise and fall Bytes 3 4 represent fall time times Set with command 31 and 32 Reports reflected power parameters The controller board returns three bytes least significant byte first Byte 1 reports the time until RF is turned off in seconds Bytes 2 3 report reflected power detection level in watts Note If the time is set to 0 the protection mode is turned off Set with command 33 152 report reflected power parameters Requests regulation mode The controller board returns one byte representing the mode report e 6 Forward power regulation e 7 Load power regulation regulation 3 External power regulation DC mode Bias 154 Set with command 3 Requests the control mode The controller board returns one byte representing the control mode e 2 Host 4 User Port e 6 Local Set with command 14 155 read control method Filename SKB 0035 pdf Author engineering Creation Date 11 Sep 06 Ac ADVANCED Command 157 read target life 158 report User port voltage 162 read process status Technical Bulletin ENERGY Command listing for RS 23
12. nd 96 Requests the revision level of the firmware software 4 data Used in conjunction with command 130 to obtain the bytes version revision of the firmware software for example 4 ASCII 1 27 characters Requests the amount of time that the generator was producing output The controller board returns four bytes least significant byte first representing the amount of time in seconds that the unit was producing output Returns the serial port address and baud rate The controller returns three bytes Byte 1 allways address 1 Bytes 2 3 baud rate Set with command 69 No function 223 Retrieves the error code 1 report error Filename SKB 0035 pdf Author engineering Creation Date 11 Sep 06 Document Technical Bulletin SKB 0035 Ac ADVANCED Command listing for ENERGY RS 232 Ethernet and Profibus Rev date for all Generators based on C3 Technology 30 Oct 06 Host Response Data p Command Description Bytes Data Bytes code register 230 Returns sensor data Byte 1 2 Reserved i report Byte 3 4 Condensation sensor data 231 report unit serial number The controller board returns four bytes for serial number LSB first This document may contain information that is confidential and proprietary information of Advanced Energy Industries The disse mination distribution or copying of this document is strictly prohibited without the express written consent of Advanced Energy Industries GmbH A
13. nly Moves the shunt capacitor of a connected match network to the specified position Send two bytes to 1 move the shunt motor to its new position 2 CSR only Accepts a value of 0 through 1000 y Read back with command 175 Clears profibus fault and error code 1 register Send one byte CSR only Note Only if Profibus module is installed Moves the series capacitor motor of a connected match network to a specified position Send two bytes to move 1 the series motor to its new position 2 CSR only Accepts a value of 0 through 1000 Read back with command 175 5 data Requests the generator type returns 5 bytes ASCII characters for example CESAR 5 ASCII characters 129 5 data supply size Requests the output capacity of the bytes generator returning packet contains 5 5 ASCII Filename SKB 0035 pdf Author engineering Creation Date 11 Sep 06 Technical Bulletin ADVANCED i Command listing for ENERGY RS 232 Ethernet and Profibus P a a C a for all Generators based on C3 Technology Host Data Bytes ae ASCII characters for example 1350 ae 130 Requests the marking of the firmware software The returning 5 data report packet contains 5 ASCII characters bytes software This command is used in conjunction 5 ASCII version With command 198 to obtain the version revision characters number of the firmware software for example C3STD Response Description Data Bytes Command 131 report
14. sting for ENERGY RS 232 Ethernet and Profibus Rev date for all Generators based on C3 Technology 30 Oct 06 Host Data Response Command Description Bytes Data Bytes delivered represent delivered power LSB first power 168 read external feedback DC Bias Requests a snapshot of external feedback level at that instant The controller board returns two bytes representing the external feedback LSB first 169 read forward power limit Requests programmed limit for forward power The controller returns the user forward power limit in watts Set with command 4 Reports current shunt and series motor positions The controller returns four bytes least significant byte first Bytes 1 2 report the current shunt report position O to 1000 capacitor Bytes 3 4 report the current series positions position 0 to 1000 Set with command 112 and 122 or found by auto tune process DE ee Reports pulsing mode The controller returns one byte ur E A report _ pu sing ulsing e 2 External pulsing l 1 P e 3 External pulsing inverted DEN efe 175 moge e 4 Enable internal pulsing by external pulsing input Set with command 27 Reports RF frequency in Hertz 178 Note This command is only available on generators report RF with variable frequency frequency Set with command 18 187 report Reports frequency tuning parameters frequency Set with command 17 tuning parameters 188 Reports t
15. tons disabled e 2 RF ON OFF buttons disabled Rotating KNOB enabled 29 Matchbox buttons disabled set partial 3 RF ON OFF buttons enabled Technical Bulletin ADVANCED i Command listing for ENERGY RS 232 Ethernet and Profibus Rev date Command for all Generators based on C3 Technology 30 Oct 06 Host Data Bytes Response Description Data Bytes 30 set User port voltage 31 set on off ramping rise time 32 set on off ramping fall time 33 set reflected power parameters 69 set serial port address and baud rate 69 set serial port address and baud rate only Profibus User port analog voltage scaling from 0 2 5V to 0 10V in steps of 0 5V A factor of 2 is implemented for example 20 10V 5 2 5V Read back with command 158 CSR only coe only ee only Sets on ramping rise time in tenths of a second Send two bytes least significant byte first Read back with command 151 Sets off ramping fall times in tenths of a second Send two bytes least significant byte first Read back with command 151 ee only ESR only Filename SKB 0035 pdf pdf Author engineering Creation Date 11 Sep 06 Sets the serial port address and baud rate Send 3 data bytes Byte 1 adresses available Byte 1 is only for compatibility Bytes 2 3 set the baud rate send least significant byte first Valid baud rates are 9600 19200 38400 57600 For 115200
16. variable frequency Read back with command 178 Specifies the number of recipe steps 19 Send one data byte representing the desired number number of of recipe steps recipe steps Accepts a value of 0 through 2 Note 0 Recipe mode is disabled Specifies the ramp time for a given recipe step Send 3 bytes least significant byte first 21 recipe step ramp time Byte 1 selects the recipe step number 1 to 2 set with command 19 Bytes 2 3 set the ramp time value Read back with command 191 Specifies the set point for a given recipe step Send 3 data bytes least ignificant byte first Byte 1 selects the recipe step number 1 to 2 set with command 19 Bytes 2 3 specify the set point value Note The set point value must be within the operating range Read back with command 188 22 recipe step set point Sets the run time in seconds a specified recipe step 23 Send 3 data bytes least significant byte first recipe step Byte 1 selects the recipe step number 1 to 2 set with run time command 19 Bytes 2 3 set the run time Read back with command 188 24 Saves the current EEPROM as peseme gen parameters save to EEPROM as preset with the given presets number s ieeeroltarpesautntegver 1 Comm 0to9 Rev date Rev 30 Oct 06 A 04 Host Data Bytes Response Data Bytes CSR only ese only l i i re only CSR only ER only T Filename SKB 0035 pdf pdf Author engineering
Download Pdf Manuals
Related Search