PPC-100 - hardware
Contents
1. PPC 100 486 based Panel PC with 10 4 LCD display Copyright Notice This document is copyrighted 1997 by Advantech Co Ltd All rights are reserved Advantech Co Ltd reserves the right to make improve ments to the products described in this manual at any time without notice No part of this manual may be reproduced copied translated or transmit ted in any form or by any means without the prior written permission of Advantech Information provided in this manual is intended to be accurate and reliable However Advantech assumes no responsibility for its use nor for any infringements upon the rights of third parties which may result from its use All brand and product names mentioned herein are trademarks or registered trademarks of their respective holders FCC Class B Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment gener ates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interfer ence will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined2. Connector Function CN1 LCD backlight control CN2 Reserved CN3 Main power input CN4 IO connector A CN5 Peripheral power input CN6 I O connector B CN7 Fan power output CN8 IDE connector CN9 FDD connector CN10 Reserved CN11 LCD power control CN12 COM1 connector CN13 5V output CN14 LCD connector LCD Backlight Control CN1 1 2 Pin Function Pin Function 2 1 BLANK 2 GND 3 12V i 4 32 Main Power Input CN3 a Pin Function Pin Function 1 12V 2 GND 3 GND 4 5V Active low 28 PPC 100 User s Manual 53 51 49 5 3 1 e 6 e e e 0 e 6 o e 6 oe UO Connector A CN4 54 52 50 a d Pin Function Pin Function 1 NC 2 NC 3 GND 4 GND 5 Mouse clock 6 KB clock 7 Mouse data 8 KB data 9 VCC for MS amp KB 10 GND for MS amp KB 11 COM1 RTS 12 COM1 RI 13 COM1 RX 14 COM1 DTR 15 COM1 DSR 16 COM1 CTS 17 COM1 RLSD 18 COM1 TX 19 COM2 RTS 20 COM2 RI 21 COM2 RX Tx 22 COM2 DTR RX 23 COM2 DSR 24 COM2 CTS 25 COM2 RLSD Tx 26 COM2 TX Rx 27 COM3 RI 28 COM3 DSR 29 COM3 TX 30 COM3 RX 31 COM3 DTR 32 COM3 RLSD 33 COM3 RTS 34 COM3 CTS 35 COM4 RI 36 COM4 DSR 37 COM4 TX 38 COM4 RX 39 COM4 DTR 40 COM4 RLSD 41 COM4 RTS 42 COM4 CTS 43 GND 44 GND 45 DO3 46 DO2 47 DO1 48 DOO 49 DI3 50 DI2 51 DI1 53 DIO 53 NC 54 NC Peripheral Power Input CN5 4 3 2 1 Pin Func
3. J13 J14 J15 JRN1 JRN2 J13 J14 J15 JRN1 JRN2 Chapter 3 The Engine of PPC 100 PCM 4865 37 Cyrix DX4 100 1 3 O e 9 J13 O Gel Ji4 e Oj J15 000000000 O JARNI 2le e o e e e e 0 0 0 0 0 0 JRN2 ee o 00000 Of JRN3 OO OO J2 Tj 5 AMD DX2 66 NV8T 1 3 O 4 J13 O 04 Ji4 e e 01 15 000000000 O JRN 2lee ol O 00000000 O JRN2 0 0 O e e ee ee JANG lc OO O O J2 Is 5 AMD DX4 100 NV8T 1 3 o e e J13 O ee J14 e e 01 15 000000000 o JRNI 2 e e o O O O O O O O O O O JRN2 1 e e e JRN3 I Oo OO O O J2 LEA 38 PPC 100 User s Manual AMD DX4 100 SV8B 1 3 O e e O e e e e o 6 6 6 6 6 6 6 6 ee 2 e e o 0000000000 119 O O O O O Ol JRN3 J1 1 OO OO OO J2 e AMD DX4 120 SV8B 1 3 e e o e o O e e e e 00 e 9 0 0 0 2 e e o 0000000000 01979 O O O O O O Ol JRN3 J1 1 OO O O O O J2 ez AMD 5x86 133 1 3 o ee O ee e o e e e e 0 e e ee 2le e o 0000000000 99 O OO O O Ol JRN3 J1 3 OO ee OO J2 Te J13 J14 J15 JRN1 JRN2 J13 J14 J15 JRN1 JRN2 J13 J14
4. Follow the directions to complete the setup Changing Color Schemes After you change display drivers you may notice that the color scheme used by Windows looks strange This is because different drivers have different default colors To change the color scheme select the Control Panel from the Main window Select the Color icon You will be shown the current color scheme Choose a new color scheme and click the OK button Chapter 5 SVGA Setup 59 DOS Setup Step 1 Install Windows as you normally would for a VGA display Run Windows to make sure that it is working correctly Then exit Windows Step 2 Place the display driver diskette in drive A Type A lt ENTER gt to make this the default drive Type SETUP lt ENTER gt to run the driver SETUP program Press any key to get to the applications list Using the arrow keys select Windows Version 3 1 and press the lt ENTER gt key Press the lt ENTER gt key to select All Resolutions and then press lt END gt to begin the installation At this point you will be asked for the path to your Windows System directory default CAWINDOWS When the installation is complete press any key to continue Press lt ESC gt followed by Y to exit to DOS Step 3 Change to the directory where you installed Windows usually C WINDOWS Step 4 Type SETUP lt ENTER gt to run the Windows Setup program It will show the current Windows configuration Use the up arrow key to move to the Display line
5. J14 J15 JRN1 JRN2 J13 J14 J15 JRN1 JRN2 Chapter 3 The Engine of PPC 100 PCM 4865 35 Intel DX2 66 1 3 O Gel J13 O e J14 e e O J15 ee e e e e e e e e JRNI 210 ece O JRN2 110 ee 060000 JRN3 Ji OOO ebe Cx KI J2 l 5 Intel DX2 50 4 3 O 4 J13 ee J14 O 04 J15 6 6 6 6 e e ee e e JRNI 210 e e 000000000 O JRN2 110 Ga O O O O O Ol JRN3 Ji 000 ool looo J2 j5 gt Cyrix 5x86 100 4 3 O 6234 J13 O eel J14 e Oj J15 ee e e ee ee e JRN 2 e e o o 0000000 O JRN2 ee o 00000 Of JRN3 J1 Pul OO O O J2 145 5 36 PPC 100 User s Manual Cyrix 5x86 120 Cyrix DX2 66 Cyrix DX2 80 1 3 e e o e o o e e 0 0 e e 6 6 6 6 e e 6 6 o 0000000000 e e o O OO O O Ol JRN3 J1 O 1 O O O O O J2 ds 5 1 3 O ee o ee e o Os Or OQ OO OOO O e e 6 6 6 6 6 6 e e 0 0 o ee O O O O O Ol JRN3 J1 000 OO 000 J2 ys 1 3 e e o e o O e e Ort Q OQ OOO 00 e o 6 6 6 6 6 6 6 6 e o e e O O O O O O JRN3 J1 OO 1 OO OO J2 19528 J13 J14 J15 JRN1 JRN2
6. J15 JRN1 JRN2 Chapter 3 The Engine of PPC 100 PCM 4865 39 CPU Voltage Setting J1 J5 J1 and J5 must be set to match the CPU type The chart below shows the proper jumper settings for their respective V Voltage 5V 3 3V 3 45V 3 6V Ji MOON e o le ej o mee o ee 119 o eo le 0 2 6 2 6 2 6 o o Oleo O Oje J5 N A i OO i e o 9919 CPU Clock Select J13 J14 J15 CPU Clock Select 25MHz 33MHz 40MHz WI WW eoo J13 LE 2 3 1 2 3 0 Ole e CU be J14 1 2 3 2 3 1 2 3 WW e 010 Oe O J15 re SC 123 CMOS Battery Backup Setup J23 CMOS Setup 3 6 V Battery Clear Enable CMOS CU e ole e 1 2 3 1 23 Note All settings marked are factory set defaults 40 PPC 100 User s Manual Speaker Output J25 Speaker Output Enable Disable OO J25 e COM2 Output Select J8 J9 J16 J17 J18 COM2 settings for RS 232 422 485 RS 232 RS 422 RS 485 J8 eoo 000 000 1 3 1 3 1 3 J9 LE fei ole e ole e 1 3 1 3 1 3 J16 o o 000 0600 1 3 1 3 1 3 J17 eoo 000 000
7. e Gg g c memo JS S Si Ark Zb 1 1 0 Connector A M ra SS amp fnf sr mE EE g ri zu E e S sl CN4 DEEN i S K SC 53 E y 2x ii a E E NE EH Main Power E d E Input CN3 HIT ES zB J l E 26 PPC 100 User s Manual LCD Backlight Power Control CN1 Locating Jumpers SSD J32 SSD J29 LCD Control J30 J31 LE d s SC e Watchdog J26 SSD J27 J28 e Ne qum Speaker Output J25 Hi Tr Watchdog J24 CMOS Battery 3 B 3 2 Backup J23 ie Digital I O es Control J21 Parallel Port z i E i Mode J19 J20 e E COM2 en E j a EN Output J18 CPU Clock E S IN Ti mmm COM2 Output 413 J14 J15 4 E Ge COM2 Output J8 J9 3 Ss 32 i COMS IRQ J3 E ji COM4 IRQ J4 US CPU Type CPU Voltage JRN1 JRN2 Setting J1 J5 JRN3 Chapter 3 The Engine of PPC 100 PCM 4865 27 3 3 PCM 4865 Connector Pin Assignment Connector Assignments
8. 1 3 1 3 1 3 2 6 2 6 2 6 J18 eoo ole o o o je 0 0 WSL o OO 1 5 1 5 1 5 NB RS 485 settings use COM2 TX COM2 TX Note All settings marked are factory set defaults Chapter 3 The Engine of PPC 100 PCM 4865 41 LCD Control J30 J31 LCD Control EV ENVEE EV VSAFE 1 1 J31 KE IW ole e SFCLK SHFCLK SFCLK SHFCLK 1 1 J30 eoo WA SSD Control J27 SSD Control Disable Enable 1 1 SSD Size J29 SSD Size 512 KB 128 KB 1 1 J29 eoo 000 Note All settings marked are factory set defaults 42 PPC 100 User s Manual SSD Type Selection J28 SSD Type Selection EPROM Flash 1 1 J28 eoo Ole e SSD I O Address J32 pins 1 to 4 SSD I O Address 200 204 240 244 280 284 2C0 2C4 bk 2 1 2 2 2 1 2 J32 ee o OO OO eo OO ce oo 3 4 34 3 4 3 4 SSD Memory Address J32 pins 5 to 8 SSD Memory Address Disable DE000 DFFFF D6000 D7FFF 5 6 5 6 5 6 J32 OO eo 00 OO OO ee 78 7 8 7 8 SSD Drive Designation J32 pins 9 to 12 SSD Drive Designation Drive 1st 2nd 3rd 4th 9 10 9 10 9 10 9 10 ee ee OO oo ee OO e OOo 11 12 11 12 11 12 11 12 Note All settings marke
9. 1 General Information 9 1 7 Mounting If you decide to use a cutout within a panel to mount your PPC 100 we have included two panel mount brackets The brackets have two screws that fit in the keyhold slots on the panel PC Slide the PPC 100 backwards into the panel opening Attach the two mounting brackets by sliding the two screw heads into the keyhole slots on the rear cover Secure the PPC 100 against the back of the panel opening Ze an M 10 PPC 100 User s Manual CHAPTER System Setup General Removing Rear Panel Installing Options Installing Software to the HDD Exploded Diagram PCM 4865 and I O Adapter Replacement Power Supply and Cooling Fan Replacement 2 1 General The PPC 100 consists of a PC based industrial computer that is housed in a protective cover Your HDD DRAM power supply and CPU are all readily accessible by removing the rear panel Any maintenance or hardware upgrades can be completed simply by removing the rear panel Warning Do not begin your installation until you have verified that no power is flowing within the PPC 100 Power must be switched off Every time you service the PPC 100 you should be aware of this 12 PPC 100 User s Manual 2 2 Removing Rear Panel Unscrew the eleven screws that secure the rear cover then remove the cover Chapter 2 System Setup 13 2 3 Installing Options Installing a 2 5 HDD 1 Detach the rear panel and r
10. 72 pin SIMM Single Inline Memory Module socket Note The modules can only fit into a socket one way Their chips must face the CPU and their golden pins must point down into the SIMM socket 1 Ensure that all power sources are disconnected 2 Slip the memory module into the socket at a 45degree angle 3 Push the module toward the vertical posts at both ends of the socket until the module is upright and the retaining clips at both ends of the module click into place When positioned correctly the pins on top of the vertical posts should correspond to the circular holes on the ends of the module PPC 100 User s Manual 2 4 Installing Software to the HDD Installing software requires an installed HDD Software can be loaded in the PPC 100 using three methods Method 1 Use Ethernet You can use the Ethernet port to download software to the HDD Method 2 Use a FDD The FDD port is located on the rear panel Unscrew the two screws and detach the iron piece Attach a cable and power signal to the FDD port and attach to a FDD Insert a 3 5 disk containing the software and consult your software manual for installation procedures Method 3 Use the COM or parallel port You can use Lap Link 6 or similar transmission software Connect another PC to the PPC 100 with an appropriate cable and transmit the software to the PPC 100 Chapter 2 System Setup 17 2 5 Exploded Diagram This diagram shows all the components and p
11. F Relative humidity 10 to 95 40 C non condensing Shock 10G peak accerelation 11 msec duration Certifications Meets FCC CE UL Power MTBF 50 000 hrs Chapter 1 General Information 5 1 3 LCD Specifications 6 Model PPC 100T PPC 100M Display type Mono LCD Size diagonal 10 4 Max resolution 640 x 480 640 x 480 Max colors or grayscales Dot size mm x 0 33 x 0 33 0 33 x 0 33 mm 256K colors 64 gray scale levels View angle C o w 50 Luminance 75 cd m LCD model eu or Temperature 0 45 C VR controls N A Contrast Simultaneous mode LCD MTBF 50 000 hours 50 000 hours Backlight MTBF 10 000 hours 10 000 hours Yes Yes VR control knob is located on the upper right rear cover of the PPC 100M Use a screwdriver to adjust the contrast VR of the LCD display PPC 100 User s Manual 1 4 Dimensions ALA NO Chapter 1 General Information 7 1 5 I O Arrangement i h g f d c a FDD port e PS 2 mouse connector outputs b Parallel port f Keyboard connector i AC inlet c VGA port g 4 serial COM ports j Power switch d Ethernet port h 4 digital inputs 4 digital 8 PPC 100 User s Manual 1 6 Cutout suggestion The PPC 100 will stand on a shelf or a table or you can mount it into a panel Cutout panel dimensions are the following Se Cut out for panel mount Mata ur Chapter
12. and non interlaced analog monitors VGA color and VGA monochrome in high resolution modes while maintaining complete IBM VGA compatibility Digital monitors i e MDA CGA and EGA are NOT supported Multiple frequency multisync monitors are supported as analog monitors 5 2 Sleep Mode The display driver diskette contains two files that support sleep mode Simply type the filename at the DOS prompt ON COM switches to normal display mode OFF COM switches to sleep mode 5 3 Simultaneous Display Mode The panel display and CRT can be used simultaneously The PPC 100 can be set to one of three configurations using a flat panel display using a CRT or using both simultaneously The system is initially set to simultaneous display mode There are three COM files on the utility diskette which can be used to select the display Simply type the filename at the DOS prompt FP COM Enables panel display only CT COM Enables CRT display only SM COM Enables both displays at the same time 56 PPC 100 User s Manual 5 4 Software Support The drivers support the following applications using the filenames and resolutions listed Application Filename Resolution Colors Windows 3 1 VMDGX4 DRV 640x480 16 800x600 16 1024x768 16 VMDGX8 DRV 640x480 256 800x600 256 1024x768 256 VMDGX16 DRV 640x480 64K VMDGX24 DRV 640x480 16M AutoCAD R12 RCTURBOC EXP 640x480 16 800x600 16 1024x768 16 640x480 256 800x600 256 1024x768 256 640x4
13. bit Ethernet on board interface Novell NE 2000 compatible Local bus SVGA display controller LCD EL and CRT displays flat panel type configured by programming the Flash chip A socket for 512 KB solid state disk using Flash memory or EPROM One 72 pin SIMM socket accepting up to 32 MB DRAM Built in Enhanced IDE hard disk drive interface Built in floppy disk drive controller On board keyboard and PS 2 mouse connectors Four serial ports three RS 232 one RS 232 422 485 selectable One multi mode parallel port ECP EPP SPP Watchdog timer time interval is 1 6 seconds One ISA bus expansion slot Power management Single 5V power supply Chapter 3 The Engine of PPC 100 PCM 4865 25 Locating Connectors 5V Output CN13 LCD Power COM1 Connector Control CN11 CN12 LCD Connector CN14 z 1 ME Fan Power FDD Connector i CN9 D iR Output CN7 IDE Connector i i H AN9O IZ8 LA J CN8 I i i UO Connector Peripheral Power ie GA d E E B CN6 Input CN5 A EN 2
14. by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Part No 2002100020 2nd Edition Printed in Taiwan April 1997 Packing List Before installing your panel PC ensure that the following materi als have been received PPC 100 Utility Disks User s Manual Accessories for PPC 100 O socket FDD flat cable 35 cm FDD power wire 35 cm HDD flat cable 15 cm Power cord 1 8 m eAssembly mounting parts Heat Sink Note If you install a 486 or 5x86 series CPU you must install a HeatSink above the CPU in order to avoid heat damage If any of these items are missing or damaged contact your distributor or sales representative immediately iii Contents Chapter 1 General Information 1 1 1 IntroductiON cisiccicessccccssssssscssnscessccsseasssacessevesssocasduesesensesnses 2 1 2 Sp cIficati OnS 5s scccscssseascsendsscensdsnsvansacsseccestecssosasssoecsseens esess 3 1 3 LCD Specifications coomooms 6 1 4 UI E CN 7 1 5 I O Arrangement 6000000000000 0000000000000000 00000000 000 000000000000 8 1 6 Cuto
15. to select the desired screen resolution and press lt ENTER gt Make sure your monitor is able to display the resolution desired Press lt END gt to begin the driver installation process A default drive and directory path will be displayed Use the backspace key to erase this default and type in the 123 directory At this point you may be asked to create the target directory if it does not already exist After the files have been installed press any key to return to the list of supported applica tions Press lt ESC gt followed by Y to exit to DOS Copy all the files that were just created in the temporary directory onto a formatted floppy diskette Step 2 Go to your 123 directory and start the installation program Type the following commands C lt ENTER gt INSTALL lt ENTER gt Step 3 The Lotus installation program will load and present the installation menu From this menu select Advanced Options From the Advanced Options menu select Add New Drivers To Library From the Add New Drivers Menu select Modify Current Driver Set From the Modify Driver Set Menu select Text Display From the Text Display menu select one of drivers Step 4 After the selection of the appropriate VGA display driver you will need to exit this menu and return to the Main Lotus Installation Menu Do this by selecting Return To Menu Step 5 At the Main Lotus Installation Menu select Save Changes 64 PPC 100 User s Manual Step 6 At this poi
16. trip point of crowbar circuit is around 5 7V to 7 0V The power supply will go into hiccup mode against short circuit or overload conditions and will automatically recover when the adverse conditions disappear International standards Safety Standards UL 1950 D3 CSA 22 2 NO 234 VDE EN 60950 EMI Standards Conducted Limits Meets FCC docket 20780 curve B and VFG 243 1991 conducted limits Meets FCC class B radiation limits 72 PPC 100 User s Manual A 3 Specifications Input Specifications Input Voltage 90 VAC to 264 VAC Input Frequency 47 Hz to 63 Hz Input Current 1A at 115 VAC or 0 6A at 230 VAC Inrush Current Not to exceed 30 A at 115 VAC input or 60A at 230V c input cold start at 25 C Output Specifications Load Range Output MinLoad Rated Load PeakLoad Voltage Accuracy 5V 0A 4 5A 6A 4 95 to 5 05 V 12V 0A 2A 4A 11 4 V to 12 6 V 12V 0A 0 3A 0 5 A 11 4 Vto 12 6 V Factory settings While running at 60 of the rated load the 5V output is set between 4 95V and 5 05V and the other outputs are checked to be within the voltage specifications This testing is conducted on all goods before leaving the factory Total peak power will not exceed 65 W for 15 seconds Ripple peak and noise The peak to peak ripple and noise for 5V is less than 50mV while for other voltages it is less than 100mV at the rated load nominal line A 15 MHz bandwidth limited oscilloscope is used f
17. 1070 RETURN 2000 REM Subroutine 2 takes 1 second to complete 2090 RETURN 80 PPC 100 User s Manual APPENDIX 4 Digital Isolated 1 0 Interface The PPC 100 provides 4 bit digital input channels and 4 bit digital output channels Digital Input Register Address 430H Register Format Input Voltage 5 to 40 V Input resistance 1 2K 9 0 5W Isolation Voltage 2 500 Ve Maximum Speed 10 KHz Digital Output Register Address 430H Bit D3 D2 D1 DO Value D03 D02 D01 D00 Register Format Ouput Voltage Open collector 5 to 40 Ve Sink Current 200mA max Isolated Voltage 2 500 Ve EXT Output Input 0000000000 G Vp 4 3 2 14321 82 PPC 100 User s Manual APPENDIX E Monochrome LCD Display for PPC 100M only DC to DC Converter Board Replacement The procedure for replacing or servicing the DC to DC converter board is as follows 1 Turn off the system power 2 Remove the rear protective cover from the PPC 100M You do not need to remove the four screws attaching the HDD support bracket to the PPC 100M steel chassis 3 Move the HDD and its support bracket to the side and remove the four screws attaching the DC to DC board to the PPC 100M steel chassis Disconnect the cables connecting the DC to DC board to the PCM 4865 CN11 and to the VR control 4 Replace the old DC to DC board with a new DC to DC board 5 Measure the voltage according to the follow
18. 80 32K 640x480 64K 640x480 16M Lotus 1 2 3 2 0 and Lotus Symphony 1 0 1 1 V132X25 DRV 132x25 Text 16 V132X50 DRV 132x50 Text 16 VESA 1 2 VESA COM 800x600 16 1024x768 16 640x400 256 640x480 256 800x600 256 1024x768 256 640x480 32K 640x480 64K Word 5 0 VGA600 VID 800x600 16 VGA768 VID 1024x768 16 Word 5 5 VGA55600 VID 800x600 16 Chapter 5 SVGA Setup 57 VGA55768 VID 1024x768 16 WordPerfect 5 0 CHIPS600 WPD 800x600 16 CHIPS768 WPD 1024x768 16 WordPerfect 5 1 VGA600 VRS 800x600 16 VGA768 VRS 1024x768 16 5 5 Driver installation Necessary prerequisites The instructions in this manual assume that you understand elementary concepts of MS DOS and the IBM Personal Computer Before you attempt to install any driver or utility you should know how to copy files from a floppy disk to a directory on the hard disk understand the MS DOS directory structure and know how to format a floppy disk If you are uncertain about any of these concepts please refer to the DOS or Windows user reference guides for more information before you proceed with the installation Before you begin Before you begin installing software drivers you should make a backup copy of the display driver diskette and store the original in a safe place The display driver diskette contains drivers for several versions of certain applications You must install the correct version in order for the driver to work properly so make sure you know which version of the a
19. DCS1 38 DCS2 39 HDD LED 40 GND 41 VCC 42 VCC 43 GND 44 NC Active low Chapter 3 The Engine of PPC 100 PCM 4865 31 33 31 29 5 3 1 e e e e e e e e o e e o FDD Connector CN9 34 32 30 642 Pin Function Pin Function 1 GND 2 REDWC 3 GND 4 NC 5 GND 6 NC 7 GND 8 INDEX 9 GND 10 MOTEA 11 GND 12 DRVSB 138 GND 14 DRVSA 15 GND 16 MOTEB 17 GND 18 DIR 19 GND 20 STEP 21 GND 22 WDATA 23 GND 24 WGATE 25 GND 26 TKOO 27 GND 28 WPT 29 GND 30 RDATA 31 GND 32 SIDE1 33 GND 34 DSKCHG 4e LCD Power Control CN11 kah Pin Function Pin Function 119 1 VCC 2 ENAVEE 3 VSAFE 4 GND lloeo 6 ee COM1 Connector CN12 k n i e 5 9 9 10 Pin Function Pin Function 1 RLSD 2 RX 3 TX 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI 10 NC Active low 32 PPC 100 User s Manual 5V Output CN13 le Pin Function Pin Function 1 GND 2 5V 44 e 43 4200 42 LCD Connector CN14 alo ola Pin Function Pin Function 2 2 1 1 12V 2 12V 3 GND 4 GND 5 VCC 6 VCC 7 ENAVEE VEESAFE 8 GND 9 PO 10 P1 11 P2 12 P3 13 P4 14 P5 15 P6 16 P7 17 P8 18 P9 19 P10 20 P11 21 P12 22 P13 23 P14 24 P15 25 P16 26 P17 27 P18 28 P19 29 P20 30 P21 31 P22 32 P23 33 GND 34 GND 35 SHFCLK ASHFCLK 36 FLM 37 ACDCLK 38 LP 39
20. GND 40 ENABKL 41 NC 42 NC 43 VCC 44 VCC Chapter 3 The Engine of PPC 100 PCM 4865 33 3 4 PCM 4865 Jumper settings You configure your PCM 4865 to match the needs of your application by setting jumpers A jumper is the simplest kind of electric switch It consists of two metal pins and a small metal clip often protected by a plastic cover that slides over the pins to connect them To close a jumper you connect the pins with the clip To open a jumper you remove the clip Sometimes a jumper will have three pins labeled 1 2 and 3 In this case you connect either pins 1 and 2 or 2 and 3 Open Closed Closed 2 3 The jumper settings are schematically depicted in this manual as follows OO ee O e e Open Closed Closed 2 3 A pair of needle nosed pliers may be useful when working with jumpers If you have any doubts about the best hardware configuration for your application contact your local distributor or sales representative before you make any changes 34 PPC 100 User s Manual CPU Type Select Intel DX4 100 1 3 O G A O e e e e o e e 6 6 e 9 e oe 2 e e 0000000000 119 O O O O O O JRN3 J1 o OO OO 1 5 2 g J5 Intel DX 33 1 3 O ee O ee e e o e e 0 0 6 6 6 6 oeo 210 e e 0000000000 110 e O O O O O OI JRN3 J1 000 O O 000 AG E J13
21. al information systems entertainment management systems and car park automation Our panel PC is a reliable cost effective solution to your application s processing requirements PPC 100 User s Manual 1 2 Specifications General Disk drive housing Space for one 2 5 HDD Dimensions 342 mm W x 265 mm H x 61 5 mm D Weight 2 7 kg Power supply 50 Watts Input voltage 90 240V 50 60 Hz Output voltage 5V 4 5A 12V 924A 12V 90 3A Cooling fan dimensions 60 x 60 x 15 mm Lx W x H Front panel IP65 protection Standard PC Functions CPU 486SX DX DX2 25 33 66 DX4 100 120 5x86 series BIOS AWARD 128KB flash memory Chipset VIA VT82C496G 2nd level cache on board 128KB RAM 2MB to 32 MB One 72 pin SIMM socket supports fast page mode and EDO DRAM Enhanced IDE HDD interface Supports up to two IDE hard disks Floppy disk drive interface Supports up to two floppy disk drives Multi mode parallel port Supports SPP ECP EPP Serial ports Three RS 232 ports COM1 COMG and COM4 one RS 232 422 485 port COM2 RS 485 is default Battery 3 6V 600 mA lithium battery Watchdog timer Supports system reset or IRQ 15 Software enable disable Time interval is 1 6 seconds Note The PPC 100 with the optionally installed touchscreen will share COMI Chapter 1 General Information 3 Solid State Disk Function Socket One 32 pin socket for FLASH EPROM Size 512KB Flash on board Ut
22. and press lt ENTER gt A list of display drivers will be shown Use the arrow keys to select one of the drivers starting with an asterisk and press lt ENTER gt Step 5 Follow the directions on the screen to complete the setup In most cases you may press lt ENTER gt to accept the suggested option When Setup is done it will return to DOS Type WIN lt ENTER gt to start Windows with the new display driver Changing Display Drivers in DOS To change display drivers from DOS change to the Windows directory and run Setup repeating steps 4 and 5 from the previous page Besides the special display drivers marked by an asterisk you should be able to use the following standard drivers VGA 640x480 16 colors Super VGA 800x600 16 colors 60 PPC 100 User s Manual Panning Drivers Special panning drivers are provided to allow high resolution modes to be displayed on a flat panel or CRT These drivers will show a section of a larger screen and will automatically pan or scroll the screen horizon tally and vertically when the mouse reaches the edge of the display Linear Acceleration Drivers A special high performance linear acceleration driver is provided for 256 color modes This driver may require special hardware and may not be supported on all systems It is only available for Windows3 1 Chapter5 SVGA Setup 61 AutoCAD R12 These drivers are designed to work with Autodesk AutoCAD R12 They conform to the Autodesk Dev
23. arts that make up the PPC 100 Use as a guide when assembling and disassembling your system Exploded Diagram of PPC 100 PPC 100 User s Manual 18 2 6 PCM 4865 and I O Adapter Replacement To replace or service the PCM 4865 the all in one CPU board and I O adapter complete the following steps 1 Remove the rear protective cover 2 Install the PCM 4865 to the panel and screw in the four screws Chapter 2 System Setup 19 3 When the PCM 4865 is mounted in the panel plug and press the adapter into the socket see the assembly diagram below 4 Four screws on your left hand side connect the I O adapter to the PC and also connect the adapter to the PCM 4865 Screw the four screws into the panel You may change the jumper settings for RS 232 422 485 before install ing the I O adapter 20 PPC 100 User s Manual 2 7 Power Supply and Cooling Fan Replacement To service or replace the power supply and or the cooling fan the back cover must first be removed Warning Power cables must be detached before you attempt to repair the power supply 1 Disconnect the power cables and remove the four screws to detach the power supply from the panel PC 2 Refer to Appendix A for detailed power supply specifications Insure that any replacement power supply matches the system s specifications 3 The cooling fan is located inside the rear panel You can remove the cooling fan by first removing
24. cssssccssssccssscsssscsssessssecsssssssees 57 5 5 Driver Installation 0000000000000000 000000000 000000000 000000000009 Ree 58 Appendix A Power Supply Specifications 71 Appendix B Touchscreen Optional 75 Appendix C Programming the Watchdog Timer 79 Appendix D 4 Digital Isolated 1 0 Interface 81 Appendix E Monochrome LCD Display 83 CHAPTER General Information This chapter gives background informa tion on the PPC 100 Sections include Introduction Specifications LCD Specifications Dimensions T O Arrangement Cutout suggestion Mounting 1 1 Introduction 2 The PPC 100 Panel PC is a PC based industrial computer that is designed to serve as a Man Machine Interface MMI It is a PC based system with 10 4 color TFT or Mono LCD display on board Ethernet and multi COM port interfaces This simple complete and compact system lets you easily build a panel PC into your configuration By incorporating the PPC 100 into your project your product development time will definitely be shortened The PPC 100 is a compact network compatible PC with extensive features to control a dedicated system in a wide variety of applications Common industrial applications include factory automation systems precision machinery and production process control It is also suitable for many non industrial applications including termin
25. d are factory set defaults Chapter 3 The Engine of PPC 100 PCM 4865 43 Watchdog Timer Control J22 Watchdog Timer Control Enable Disable J22 eo OO Watchdog Timer Invoke Function J24 J26 Watchdog Timer Invoke Function IRQ15 System Reset J24 eo OO J26 OO eo Parallel Port Mode Select J19 J20 Parallel Port Mode Select Disable SPP EPP ECP J19 1253 1 32 23 1 2 3 1 2 3 oe e elo ole e feo J20 123 123 EEN RE 000 O eoo eoo COM3 IRQ J3 COM3 IRQ IRQ5 IRQ10 J3 1 1 eoo Ole e 44 PPC 100 User s Manual COMA IRQ J4 COM4 IRQ IRQ5 IRQ10 J4 1 1 e eo 000 Digital UO Control J21 Digital I O Control Enable Disable J21 OO e Chapter 3 The Engine of PPC 100 PCM 4865 45 46 PPC 100 User s Manual CHAPTER Software Configuration This chapter details the software configu ration information It shows you how to configure the card to match your applica tion requirements Sections include Introduction Utility Disk Ethernet Utility Disk 4 1 Introduction The PPC 100 system BIOS and custom drivers are located in a 128 Kbyte 32 pin JEDEC spec Flash ROM device designated U15 A single Flash chip holds the syst
26. em BIOS VGA BIOS and network Boot ROM image The system BIOS can be configured via software This method minimizes the number of chips and eases configuration You can change the system BIOS simply by reprogramming the Flash chip 4 2 Utility disk The PPC 100 is supplied with a software utility disk This disk contains the necessary files for setting up the Ethernet controller Directories and files on the disk are as follows README DOC SSD COOKROM EXE BIOS 4865 TFT BIN Lasostsa BIN AWDFLASH EXE COOKROM EXE A program that converts application files into binary files files with a BIN extension These are then written into the SSD Flash ROM devices 4865_TFT BIN Supports 640 x 480 color TFT The standard BIOS file without Ethernet Boot ROM 4865TSB BIN Default Supports 640 x 480 color TFT The standard BIOS file with Ethernet Boot ROM AWDFLASH EXE This program allows you to write the VGA display driver files to the BIOS Flash ROM The VGA files all come ready formatted for the PPC 100 with BIN extensions See README DOC These files support various CRT and flat panel displays They are custom written and can be made available upon request 48 PPC 100 User s Manual Software Configuration The PPC 100 s on board Boot ROM have been written to the ROM BIOS chip If you want to change the settings configure the software as follows 1 Power on the PPC 100 with a color TFT
27. emove 2 Place the HDD in the appropriate location inside the PPC 100 and tighten the screws 3 Connect the cable from the HDD to the PC board CNS Warning 1 Plug the other end of the cable to the HDD with pin 1 on the cable correspond ing to pin 1 on the hard drive Improper connection will damage the HDD 2 Be careful not to damage the CPU board with your tools 14 PPC 100 User s Manual Installing a CPU If you want to improve your system s performance you can upgrade your CPU 1 Locate Pin 1 in the corner of the CPU socket 2 Carefully align Pin 1 on the CPU with Pin 1 on the socket Insure that the notch on the corner of the CPU matches the notch on the inside of the socket 3 Place the CPU in the socket It should insert easily If not make sure the notches on the corners of the CPU and the socket are aligned 4 Gently push the CPU into the socket There will probably be a small gap between the CPU and the socket even when it is fully seated DO NOT USE EXCESSIVE FORCE NOTE When you install a new CPU you may have to adjust other settings on the board eg CPU type CPU clock and CPU power to accommodate it Make sure that the settings are correct for your CPU See chapter 3 for jumper settings D Warning Improper settings may damage the CPU Chapter 2 System Setup 15 16 Installing DRAM SIMM You can install from 2 MB to 32MB of DRAM memory The PCM 4865 CPU card provides one
28. en resolution and press lt ENTER gt make sure your monitor is able to display the resolution desired Press lt END gt to begin the driver installation process A default drive and directory path will be displayed Use the backspace key to erase this default and type in the WordPerfect directory At this point you may be asked to create the target directory if it does not already exist After the files have been installed press any key to return to the list of supported applications Press lt ESC gt followed by Y to exit to DOS Step 2 Start WordPerfect and press lt SHIFT gt lt F1 gt to enter the setup menu Select D for Display and G for Graphics Screen Type and then choose the desired Chips VGA resolution Configuring WordPerfect 5 0 for 132 columns 68 PPC 100 User s Manual Follow these instructions to configure WordPerfect 5 0 for 132 column text mode Step 1 To use the SETCOL program to set 132 columns and 25 rows type the following command SETCOL 132 25 lt ENTER gt Step 2 Start WordPerfect The program will detect the number of rows and columns automatically If for some reason WordPerfect is unable to adapt to 132 columns by 25 rows start WordPerfect with the following command WP SS 25 132 ENTER Configuring WordPerfect 5 1 for 132 columns Start WordPerfect and press lt SHIFT gt lt F1 gt to enter the setup menu Select D for Display and T for Text Screen Type and then select Chips 132 Column Te
29. fications Light Transmission typically 75 at 550 nanometer wavelength optimized for flat panel displays All measurements per ASTM D 10036 61 Visual Resolution Antiglare 6 1 minimum Measured according to USAF 1951 Resolution Chart under 30x magnification with test unit located approximately 1 5 3 8 mm from surface of resolution chart Haze Antiglare less than 1596 Per ASTM D 103 61 Gloss Antiglare 96 gloss units Per ASTM D 2457 70 B 3 Environmental Specifications Temperature Operating 10 C to 50 C and storage 40 C to 71 C Relative Humidity Operating 90RH at 35 C and storage 90RH at 35 C for 240 hours noncondensing Chemical Resistance The active area of the touchscreen is resistant to the following chemi cals when exposed for a perion of one hour at a temperature of 71 F 21 C Acetone Methylene chloride Methyl ethyl ketone Isopropyl alcohol Hexane Ammonia based glass cleaners Turpentine Mineral spirits Foods and beverages Appendix B Touchscreen 77 78 PPC 100 User s Manual APPENDIX Programming the Watchdog Timer The PPC 100 is equipped with a watch dog timer that resets the CPU or generates an interrupt if processing comes to a standstill for whatever reason This feature ensures system reliability in industrial standalone or unmanned environments Jumpers J22 J24 J26 control the watchdog settings The default configuration of t
30. he timer is enabled with system reset To enable the watchdog timer you must write a program which reads I O port address 443 hex at regular intervals The first time your program reads the port it enables the watchdog timer After that your program must read the port at time interval of less than 1 6 seconds otherwise the watchdog timer will activate and reset the CPU or generate an interrupt on IRQ15 When you want to disable the watchdog timer your program should read I O port 043 hex If CPU processing comes to a standstill because of EMI or a software bug your program s signals to I O port address 443 to the timer will be interrupted The timer will then automatically reset the CPU or invoke an IRQ and data processing will continue normally You must write your program so that it reads I O port address 443 at an interval shorter than the timer s preset interval The timer s intervals have a tolerance of 30 so you should program an instruction that will refresh the timer about every second The following program shows how you might program the watchdog timer in BASIC 10 REM Watchdog timer example program 20 X INP amp H443 REM Enable and refresh the watchdog 30 GOSUB 1000 REM Task 1 takes 1 second to complete 40 X INP amp H443 REM Refresh the watchdog 50 GOSUB 2000 REM Task 2 takes 1 second to complete 60 X INP amp H043 REM Disable the watchdog 70 END 1000 REM Subroutine 1 takes 1 second to complete
31. ice Interface ADI for Rendering drivers and Display drivers These display list drivers accelerate redraw pan and zoom functions Driver installation Step 1 Place the display driver diskette in drive A Type A lt ENTER gt to make this the default drive Type SETUP lt ENTER gt to run the SETUP program Press any key to get to the applications list Using the arrow keys select AutoCAD Release 12 and press lt ENTER gt This will display a list of supported driver resolutions Using the arrow keys and the lt ENTER gt key select the resolutions that are appropriate for your monitor When all of the desired resolutions have been selected press lt END gt to begin the installation At this point you will be asked for a drive and directory to copy the driver files Enter the drive and directory that contains the installed AutoCAD R12 If the destination directory does not exist you will be asked for confirmation When the installation is complete press any key to continue Press lt ESC gt followed by Y to exit to DOS Step 2 Go to the AutoCAD directory where the new drivers were installed and run the driver installation program by typing ACAD12 r lt ENTER gt This program will configure your AutoCAD R12 to use the new display drivers Select TurboDLD Classic Configuring TurboDLD Select Configure Video Display In Display Device Configuration choose Select Graphics Board Resolution Then choose Select Display Graphics Board Af
32. ility software Includes software to prepare files for EPROM Local bus Flat Panel VGA Interface Chipset C amp T 65545 Display memory MB DRAM Display type simultaneously supports CRT and flat panel displays e CRT display mode Supports resolutions up to 1024 x 768 E 256 colors Panel display modes Supports resolutions up to 640 x 480 True Colors Ethernet Controller Function Chipset Realtek RTL 8019 Type 16 bit Ethernet Novell NE2000 compatible Connector 10 Base T connector on board Digital Isolated I O Ports 4 optically isolated inputs Input voltage 5 to 40 V Input resistance 1 2K 0 5 W Isolation voltage 2 500 Ve Maximum speed 10KHz 4 optically isolated outputs Output voltage Open collector 5 to 40V Sink current 200 mA max each channel Isolated voltage 2 500 Ve 4 PPC 100 User s Manual Touchscreen optional Type Analog resistive Resolution continuous Light Transmission 75 Surface meets ASTM D 1044 standard Taber Abrasion Test Controller RS 232 interface uses COM1 Power consumption 5V 200mA Software driver supports both DOS and Windows Durability 30 million touches in life Option Modules e CPU 486 SX DX DX2 25 33 66 DX4 100 120 5x86 series Memory 2 4 8 16 32 DRAM Fast page mode HDD 2 5 HDD Operating System Windows 95 DOS OS 2 Windows 3 1 Touchscreen Analog resistive Environment Temperature 0 to 45 C 32 to 113
33. ing directions a Disconnect the 44 pin cable connecting the LCD display then connect the cable linking the DC to DC board to the PCM 4865 CN 11 b Short close the connector CN1 with a mini jumper c Power on the PPC 100M Using a multimeter to measure the voltage at V to make certain V p 23 V The V is available from the CN1 mini jumper d Power off the PPC 100M 6 Reassemble the PPC 100M E Warning To avoid damage from power surges do not touch the power supply when measuring voltage 84 PPC 100 User s Manual Note 1 The jumper JP1 can be set V or V pg For the PPC 100M the correct setting is V p If this setting is incorrect damage to the LCD display will result 2 The voltage measured at V must be 23 V pe to prevent damage to the LCD display This voltage must be measured prior to connecting cables to the LCD display every time the DC to DC converter is replaced Warning Advantech recommends that customers only allow a qualified service technician to make adjustments to VR1 Contact Advantech cus tomer service if you need further assistance Appendix E Monochrome LCD Display 85 86 PPC 100 User s Manual
34. n Step 1 Place the display driver diskette into drive A Make A the default drive by typing A lt ENTER gt Run the SETUP program by typing SETUP lt ENTER gt Press any key to display a list of supported applica tions Use the arrow keys to select VESA Driver Version 1 2 and press lt ENTER gt Press the ENTER key to select All Resolutions and press lt END gt to begin the installation A default drive and directory path will be displayed Use the backspace key to erase this and type in a directory that is in the directory path such as C BIN or C UTILS After the files have been installed press any key to return to the list of supported applications Press lt ESC gt followed by Y to exit to DOS Step 2 To install the VESA driver type either VESA lt ENTER gt or VESA lt ENTER gt at the DOS prompt The optional command line parameter enables all of the available modes Make sure that your monitor is capable of displaying these high resolution modes before enabling them NOTE If the video BIOS already supports VBE extended video modes DO NOT use this driver Run the VTEST EXE program to see if the video BIOS supports the VBE modes 66 PPC 100 User s Manual Word These drivers are designed to work with Microsoft Word 5 0 and 5 5 If you have already installed Word on your computer go to Step 2 to install the new video driver Step 1 Install Word as normal Step 2 After you complete the Word installation
35. net configuration program will then be displayed 3 This simple screen shows all the available options for the Ethernet interface Just highlight the option you wish to change by using the Up and Down keys To change a selected item press lt Enter gt and a screen will appear with the available options Highlight your option and press lt Enter gt Each highlighted option has a helpful message guide displayed at the bottom of the screen for additional information 4 After you have made your selections and your are sure that this is the configuration you want press ESC A prompt will appear asking if you want to save the configuration Press Y if you want to save The Run diagnostics in the Ethernet Main Menu also offers three very useful diagnostic functions These are 1 Run EEPROM test 2 Run Diagnostics on Board 3 Run Diagnostics on Network Each option has its own display screen which shows the format and result of any diagnostic tests undertaken Chapter 4 Software Configuration 53 54 PPC 100 User s Manual CHAPTER SVGA Setup The PPC 100 features an on board flat panel VGA interface This chapter provides instructions for installing and operating the software drivers on the included display driver diskette Introduction Sleep Mode Software Support Driver Installation 5 1 Introduction The 65545 VGA BIOS supports monochrome LCD and color TFT flat panel displays It also supports interlaced
36. nt the Installation Menu will prompt you for the name of your new Lotus configuration file The Lotus system will prompt you with the default value 123 SET but you may want to use a filename that indicates the resolution of its driver For example if you installed the 132 column by 25 line driver you could name this driver 132X25 SET or if you installed the 80 by 50 driver you may want to call the file 80X50 SET Step 7 The installation of your Lotus 1 2 3 driver is now complete You will need to exit the Lotus installation program at this point At the main Lotus Installation Menu select Exit NOTE If your driver set is not 123 SET you have to type the filename of your driver set in the command line when you start Lotus 1 2 3 For example if you named your driver set 132X25 SET type the following to start Lotus 1 2 3 123 132X25 SET ENTER Chapter 5 SVGA Setup 65 VESA The Video Electronics Standards Association VESA has created a standard for a Super VGA BIOS Extension VBE This defines a standard software interface to allow application programs to set and control extended video modes such as 800x600 graphics on video adapters from different manufacturers The VESA driver adds this Super VGA BIOS Extension to the VGA BIOS Any application program which supports the VESA standard driver interface can be used with this driver This VESA driver conforms to the VESA Super VGA Standard VS891001 Driver installatio
37. or Mono display attached This is the default setting for the PPC 100 Ensure that the AWDFLASH EXE and BIN files are located in the working drive NOTE Ensure that you do not run AWDFLASH EXE while your system is operating in with any memory management software 2 At the prompt type AWDFLASH EXE and press Enter The VGA configuration program will then display the following FLASH MEMORY WRITER v 1 2 Copyright c 1993 Award Software Inc For VIA486A 310L200 08 23 96 Flash Type For VIA486A 310L2AK File Name to Program Error Message VGA Setup screen Chapter 4 Software Configuration 49 3 At the prompt enter the new BIN file which supports your display When you are sure that you have entered the file name correctly press lt Enter gt 4 The screen will ask Do you want to save BIOS If you change your mind or have made a mistake press N to abort Press Y if you wish to save the existing configuration before changing it Then type the name under which you want to save the current configuration 5 The prompt will then ask Are you sure to program Press Y if you want the new file to be written into the BIOS Press N to exit the program The new software configuration will then write to the ROM BIOS chip This configuration will remain the same until you run the AWDFLASH EXE program and change the settings 50 PPC 100 User s Manual 4 3 Ethernet Utility Di
38. or testing with each output terminated with a 0 47uF capacitor Line regulation The line regulation for 5V is less than 1 at 12 V it is less than 296 at 12 V it is less than 3 while measuring at the rated load and 10 of input voltage changing Appendix A Power Supply Specifications 73 Load regulation The load regulation for 5V 12V is less than 3 for 12V it is less than 5 Measuring is performed by changing the measured output load 40 from 60 rated load and keeping other outputs at 60 rated load Environmental Specifications Temperature range Operating 0 C to 50 C Storage 20 C to 85 C Altitude 0 10000 ft Relative humidity 5 to 95 non condensing 74 PPC 100 User s Manual APPENDIX Touchscreen Optional General Information Specifications Environmental Specifications B 1 General Information e 75 light transmission Advanced second generation 5 wire resistive technology Enhanced visual resolution anti glare surface treatment Enhanced scratch resistant hard coat Accutouch touchscreens are UL recognized components file no E133802 When properly installed ball impact compliance meets UL 1950 standard Fire Retardation Compliance meets UL 746C 0 75 19 mm flame test Systems incorporating these touchscreens controllers and cables have been approved to FCC class A and B compliance 76 PPC 100 User s Manual B 2 Speci
39. place the display driver diskette into drive A Make A the default drive by typing A lt ENTER gt Run the SETUP program by typing SETUP lt ENTER gt Press any key to display a list of supported applications Use the arrow keys to select Word and press lt ENTER gt Use the arrow keys to select the desired screen resolution and press lt ENTER gt make sure your monitor is able to display the resolution desired Press lt END gt to begin the driver installation process A default drive and directory path will be displayed Use the backspace key to erase this and type in your Word directory After the files have been installed press any key to return to the list of supported applications Press lt ESC gt followed by Y to exit to DOS Step 3 Copy the driver file for the desired resolution that was just installed to SCREEN VID Chapter 5 SVGA Setup 67 WordPerfect These drivers are designed to work with WordPerfect 5 0 or 5 1 They support 132 column display in editing mode and high resolution graphics display in PreView mode Driver installation Step 1 Place the display driver diskette into drive A Make A the default drive by typing A lt ENTER gt Run the SETUP program by typing SETUP lt ENTER gt Press any key to display a list of supported applica tions Use the arrow keys to select WordPerfect and press lt ENTER gt A list of supported screen resolutions will be displayed Use the arrow keys to select the desired scre
40. pplication you have 58 PPC 100 User s Manual Windows Setup These drivers are designed to work with Microsoft Windows 3 1 You may install these drivers through Windows or in DOS Step 1 Install Windows as you normally would for a VGA display Run Windows to make sure that it is working correctly Step 2 Place the display driver diskette in drive A In Windows Program Manager choose File from the Options Menu Then from the pull down menu choose Run At the command line prompt type A WINSETUP Press the ENTER key or click OK to begin the installation At this point the setup program locates the directory where Windows is installed For proper operation the drivers must be installed in the Windows subdirectory Press ENTER to complete the installa tion Once completed the Display Driver Control Panel appears on the screen This Control Panel allows you to select and load the installed drivers Another method of installing these drivers is through the File Manager Click on Drive A Then double click on WINSETUP EXE to begin installation Changing Display Drivers in Windows To change display drivers in Windows select the Windows Setup icon from the Main window You will be shown the current setup configura tion Select Change System Settings from the Option menu Click on the arrow at the end of the Display line You will be shown a list of display drivers Click on the driver you want Then click on the OK button
41. sk The PPC 100 Ethernet driver utility disk contains required files for installing and setting up the Ethernet controller ROOT 8019 CFG DIR DOC README DOC RELEASE DOC PG8019 EXE RSET8019 EXE EXE RSET8019 EXE FILEPATH LST MAINMENU TXT HELP8019 EXE MSCLIENT LANTAS4 LANTASS MSLANMAN DOS MSLANMAN OS2 NDIS NWCLIENT NWSERVER PKTDRV SCO TXT WFW31 WFW311 WIN95 WINNT31 WINNT35 Chapter 4 Software Configuration 51 RSET8019 EXE This program enables you to view the Ethernet configuration reconfigure the Ethernet interface media and execute useful diagnostic functions PG8019 EXE The PPC 100 is set at the factory by using this program Upon receipt of the PPC 100 you should use RSET8019 EXE to configure for the working environment If by chance the Ethernet EEPROM is corrupted the PG8019 EXE program allows you to configure the card 8019 CFG This file contains the configuration parameters that are used by PG8019 EXE 52 PPC 100 User s Manual Ethernet software configuration The PPC 100 s on board Ethernet interface supports all major network operating systems I O addresses and interrupts are easily configured via the Award BIOS Setup To configure the media type to view the current configuration or to run diagnostics do the following 1 Power the PPC 100 on Ensure that the RSET8019 EXE file is located in the working drive 2 At the prompt type RSET8019 EXE and press Enter The Ether
42. ter choosing a graphics board go to Select Display Resolution After selecting the display resolution save the new configu ration and return to the main menu 62 PPC 100 User s Manual Basic Configuration Menu This menu allows you to modify Number of AutoCAD Command Lines Font Size 6x8 8x8 8x14 8x16 12x20 12x24 Dual Screen Enable Disable User Interface Configuration Double Click Interval Time BP Button BP Highlight Patt Line Xor Rect Both BP Refresh Enable Disable BP Cache Enable Disable Expert Configuration Menu This menu allows you to modify Display List Enable Disable Drawing Cache Enable Disable Use Acad 31 bit space Yes No Internal Command Echo Enable Disable BP Zoom Mode Freeze Float Regen Mode Incremental Fast If your previously installed driver is not TurboDLD you will have to reconfigure the RENDER command the first time you use it Chapter 5 SVGA Setup 63 Lotus 1 2 3 and Lotus Symphony These drivers are designed to work with Lotus 1 2 3 versions 2 0 2 01 and 2 2 and with Lotus Symphony versions 1 0 and 1 1 Driver installation Step 1 Place the display driver diskette into drive A Make A the default drive by typing A lt ENTER gt Run the SETUP program by typing SETUP lt ENTER gt Press any key to display a list of supported applica tions Use the arrow keys to select Lotus Symphony and press lt EN TER gt A list of supported screen resolutions will be displayed Use the arrow keys
43. the four screws Replace the power supply Chapter 2 System Setup 21 Replace the cooling fan PPC 100 User s Manual 22 CHAPTER The Engine of PPC 100 PCM 4865 Introduction Features e PCM 4865 Connector Pin Assignment PCM 4865 Jumper Settings 3 1 Introduction The PCM 4865 is a highly reliable single board computer based on the SX DXA and 5x86 CPU It offers built in functionality comparable to a complete industrial PC system including a VGA LCD controller network communications solid state disk and four serial ports three RS 232 and one RS 232 422 485 in a small 8 x 5 75 form factor On board features include DRAM SIMM socket one EPP ECP parallel port an enhanced IDE HDD controller for up to two drives a FDD controller a PS 2 keyboard mouse interface plus 4 channel digital I O ports In addition the PCM 4865 also offers several industrial features An on board solid state disk SSD emulates a floppy drive using EPROM or Flash memory device while maintaining complete DOS compatibility It also offers faster data access and longer MTBF than mechanical disk drives and is an ideal solution for critical commercial or industrial applications The watchdog timer ensures the system will be reset if it stops due to a program bug or EMI problem 24 PPC 100 User s Manual 3 2 Features e 80486SX DX DX2 DX4 5x86 processor selectable clock speed 128 KB second level cache on board 16
44. tion Pin Function MUERE 1 12V 2 GND 3 GND 4 5V Active low Chapter 3 The Engine of PPC 100 PCM 4865 29 53 51 49 5 3 1 e e o e e e e e o e e o UO Connector B CN6 54 52 50 642 Pin Function Pin Function 1 NC 2 NC 3 RESET IN 4 GND 5 Watchdog OUT 6 GND 7 GND 8 SPEAKER OUT 9 VCC 10 HDD LED 11 VGA Blue 12 12V 13 VGA GREEN 14 VGA VSYNC 15 VGA RED 16 VGA HSYNC 17 GND 18 GND 19 GND 20 GND 21 PP ERR 22 GND 23 PP INIT 24 PP STB 25 PP SLIN 26 PP AFD 27 PP DO 28 PP D1 29 PP D2 30 PP D3 31 PP D4 32 PP D5 33 PP D6 34 PP D7 35 PP PE 36 PP ACK 37 PP SLCT 38 PP BUSY 39 Reserved 40 Reserved 41 VCC 42 VCC 43 NET LED RX 44 NET LED COL 45 NET XMT 46 NET XMT 47 NET RCV 48 NET RCV 49 NET LED RX 50 NET LED COL 51 GND 52 GND 53 NC 54 NC Fan Power Output CN7 1 Pin Function Pin Function b 1 5V 2 GND 3 12v Active low 30 PPC 100 User s Manual 43 41 39 S S e e o e e o IDE Connector CN8 eee eee Pin Function Pin Function A O A 1 HD REST 2 GND 3 D7 4 D8 5 D6 6 D9 7 D5 8 D10 9 D4 10 D11 11 D3 12 D12 13 D2 14 D13 15 D1 16 D14 17 DO 18 D15 19 GND 20 NC 21 NC 22 GND 23 IOW 24 GND 25 IOR 26 GND 27 IORY 28 NC 29 NC 30 GND 31 IRQ 32 1016 33 Al 34 NC 35 AO 36 A2 37
45. ut suggestion 0000000 0000000000000000 0000 anae en eaeneeanane 9 1 7 Mou nting EE 10 Chapter 2 System Setup 11 2 1 General 12 2 2 Removing Rear Panel 00000000000000 000000000000 13 2 3 Installing Options 0000000000000000 00000000000000 eee eere esee eee 00e 14 2 4 Installing Software to the HDD 17 2 5 Exploded Diagram cec eee ecce esee eee 00000000 000e 18 2 6 PCM 4865 and I O Adapter Replacement 19 2 7 Power Supply and Cooling Fan Replacement 21 Chapter 3 The Engine of PPC 100 PCM 4865 23 3 1 Introduction EE 24 3 2 Features e 25 3 3 PCM 4865 Connector Pin Assignment 28 3 4 PCM 4865 Jumper settings 0oo000000000000 00000000 0000000 0000o 34 Chapter 4 Software Configuration 47 ZN Biel nen nane 48 42 Utility disk E 48 4 3 Ethernet Utility Disk 00000000 0000000 0000 000o 51 Chapter 5 SVGA Setup 0000000000000000000000000000000000 55 5 1 Imtroduction cevcecscessccscciscsccicectsostcsosdescecsecscsvoesssecssecssesdeees 56 5 2 Sleep A 560550056890 9059i5 5959960595060995 00 566050005665 56 5 3 Simultaneous Display Mode 00000000 000 56 5 4 Software Support ccss
46. xt Chapter 5 SVGA Setup 69 Windows NT The setup prodedure is as follows Step 1 Run Windows NT setup from Main Group and choose Option from the menue ALT 0 Step 2 Select change system setting ALT C You can choose Other under the display section Step 3 Insert display driver disk in the appropriate floppy drive Windows 95 Complete the following steps to install the Windows 95 display driver Step 1 Boot system with VGA or Super VGA driver Step 2 Click the right mouse button to pull down a menu and select Display Select Change Display then Change Monitor Step 3 After changing the monitor you may change the adapter Step 4 Select Have disk and finish the setup 70 PPC 100 User s Manual APPENDIX Power Supply Specifications Introduction Features Specifications A 1 Introduction The power supply of the PPC 100 is a 50 W triple output universal input switching power supply It has been designed for network applications A 2 Features General Features Efficiency Higher than 70 while measuring at nominal line and rated load Hold up time 20 ms typical at 115 V input and rated load which is measured from the end of the last charging pulse to when the main output drops down to 95 output voltage Protection If the power supply fails to control itself the built in over voltage protection circuit will shut down the outputs to avoid damaging external circuits The
Download Pdf Manuals
Related Search