UHBX-R-PSE - Hall Research
Contents
1. Block Diagram for power sent from Sender to Receiver UHBX S PD UHBX R PSE HDMI gt HDMI RS 232 lt lt wie RS 232 IR In IR Out IR Out lt lt IR In This Configuration is available in kit form Kit part number UHBX P2 Figure 2 Block Diagram for power sent from Receiver to Sender ns gt HDMI Extender with Power IR and RS 232 Full duplex RS232 Serial Port extension is provided that can operate at any baud rate to 115 200 independent of video activity The extender can also extend IR from one end to the other IR Detector and IR Emitter cables are sold separately The IR extension preserves the modulation carrier frequency and provides compatibility to virtually any standard It supports modulation range from 30 KHz to 60 KHz 2 0 Features e Extends HDMI or DVI video to 500 ft on just one Cat6 e Includes RS232 and IR extension in both directions e Supports virtually all HDMI and DVI resolutions including 4Kx2K e Only one end requires power other side is powered via UTP e Power over HDBaseT meets IEEE 802 3af standard e Sturdy metal enclosures with mounting provisions e Complies fully with HDBaseT standard e Runs from just one 5vDC supply e RS232 Supports all baud rates regardless of presence of video e IR extension is carrier frequency agnostic and supports 30 KHz to 60 KHz modulation to provide compatibility across all IR standards e Fully isolates ground between TX and RX sides e2. 2 AL f Coy SSiyyywO amp To UHBX Series 1 0 Introduction This manual covers a few of the UHBX series of HDMI extenders by Hall Research These products are comprised of individual sender and receiver modules that can send HDMI bidirectional IR full duplex RS232 and PoH power over HDBaseT over distances of up to 150 meters 500 feet using a single Cat6 cable The products can extend HDMI or single link DVI video of virtually any resolution to a maximum distance of 500 ft 150 m Two user selectable distance modes are available Standard and Long Reach These modes are explained further in section 4 4 of this manual The extenders comply with Power over HDBaseT or PoH hence only one end requires a power supply The end identified as PSE power sourcing equipment injects power on to the Cat6 cable and the side identified as PD powered device is powered through the Cat6 cable The PSE side requires connection of an AC adapter that supplies 5v DC while the PD side is simply powered through the RJ45 connector from the opposite side Senders and Receivers are available in both PSE and PD versions Prior to placing an order it is important to determine which scenario works best for a given setup since the direction of power flow is determined by the model numbers ordered and cannot be reversed in the field UHBX S PSE UHBX R PD This Configuration is available in kit form Kit part number UHBX P1 Figure 1
3. 8 bit 1080p deep color and 4Kx2K are not supported The extender has a mode setting that affects the maximum achievable extension distance The Distance Mode switch is located on the Receiver the Sender does not have a mode switch The mode switch is a small slide switch located under the HDMI output connector on the Receiver Two modes are available Standard STD and Long Reach L R If the length of UTP cable is less than 100 meters 330 ft then STD mode should be used For lengths above 330 ft Long Reach L R mode must be set paiia ad Figure 11 Mode Switch Mode Select Switch When using Long Reach ensure that the source does not output 1080p with deep color nor 4K video since these formats are not supported in L R mode 4 5 LED indicators ACTIVITY PWR Figure 12 LED Indicators Power Indicates unit is powered HDMI Extender with Power IR and RS 232 5 0 Troubleshooting If you are experiencing problems getting the extender to work properly please use the following troubleshooting suggestions Make sure that all of the connections on both the sender and the receiver are solid Loose connections are the number one cause of issues Try resetting the system by unplugging the power supply connected to the PSE side waiting 5 seconds and plugging it back Check the state of the LED s on the front of both the sender and the receiver Refer to the table in section 4 5 to
4. Compact Rugged Reliable and Economical e Made in USA 3 0 Model numbers covered in this User s Manual Individual Ends UHBX S PSE HDMI RS232 IR PoH UTP Sender with Power Supply PSE UHBX S PD HDMI RS232 IR PoOH UTP Sender Remotely Powered PD UHBX R PSE HDMI RS232 IR PoOH UTP Receiver with Power Supply PSE UHBX R PD HDMI RS232 IR POH UTP Receiver Remotely Powered PD Kits UHBX P1 HDMI RS232 IR POH UTP Extender Sender PSE powers Receiver PD UHBX P2 HDMI RS232 IR PoOH UTP Extender Receiver PSE powers Sender PD UHBX Series 4 0 Setup 4 1 Package Contents All part numbers that include a Sender come with one 1m 3 ft HDMI cable for connection to a video source The PSE devices and kits also include a universal 5vDC power adapter 4 2 Sender Connections LR O A DETECTOR ACTIVITY PWR EMITTER Figure 3 Sender Connections UHBX S PSE shown above 4 2 1 Sender Video Connection Connect the HDMI input to the source using the cable provided If you need to substitute a different cable for example if the 3 ft supplied cable is not long enough then you should use quality HDMI cables The HDMI input connector on the box has a locking nut above it Hall Research offers compatible locking high quality HDMI input cables Figure 4 Hall Research C HDMI L high bandwidth HDMI cable with flip up locking tab PPP Pe a LESS SS SSS HDMI Extender with Power IR and RS 232 4 2 2 Sender Seri
5. interpret the status being indicated Ifthe cable length is longer than 100 meters 330 ft set the Mode Switch on the receiver to L R Long Reach position see section 4 4 In L R mode the unit does not support deep color or 4Kx2K video Make sure the display is compatible with the video source by connecting them directly Make sure that the UTP or STP cable meets the requirements Never use low skew cable for digital video extension low skew cables are suited for analog video extension but do not work well for digital video Read section 4 2 4 for UTP cable requirements The extender requires that the source DDC signals of its HDMI output operate atl100 KHz or less and support clock stretching The vast majority of sources meet these requirements But if you determine that a particular source does not by substituting a video pattern generator or a different source an HDMI transceiver may be needed Hall Research offers the model EMX HD AUD that has a compatible output can handle virtually any HDMI input and has proven its ability to resolve source incompatibility issues If you still are not able to get the system working properly contact Hall Research support preferably via email or the form on support page of www hallresearch com with a detailed description of the issue and the troubleshooting steps you have taken Do not open or try to repair the unit yourself as this will void your warranty To return th
6. 10 to 90 non condensing Operating 32 to 122 F 0 to 50 C 10 to 90 non condensing Cooling Convection Mounting End plates have L bracket with hole for surface mounting Enclosure type Metal Aluminum ends Aluminum Extrusion Dimensions 1 18 H x 4 13 W x 4 57 D 30mm H x 105mm W x 116mm D Depth excludes connectors Product weight Sender 9 3 oz 0 58 Ib or 264 g Receiver 10 oz 0 63 Ib or 284 g Kit shipping 37 oz 2 3 lb or 1050 g includes sender receiver power supply power cord HDMI cable manual and packaging Vibration ISTA 1A in carton International Safe Transit Association Safety CE EMI EMC CE FCC Class A MTBF 90 000 hours Calculated Estimate Warranty 2 years parts and labor Specifications are subject to change without notice ns 1 IF HALL RESEARCH Copyright 2013 Hall Research Inc All rights reserved 1163 Warner Ave Tustin CA 92780 Ph 714 641 6607
7. HALL USER S MANUAL RESEARCH HDBT HDMI Video Extender with Bidirectional IR and RS232 Send HDMI IR full duplex RS232 and POH Power 500 ft 150 m ona single Cat6 cable Model numbers covered in this User s Manual Individual Ends UHBX S PSE HDMI RS232 IR PoH UTP Sender with Power Supply PSE UHBX S PD HDMI RS232 IR PoOH UTP Sender Remotely Powered PD UHBX R PSE HDMI RS232 IR PoH UTP Receiver with Power Supply PSE UHBX R PD HDMI RS232 IR PoH UTP Receiver Remotely Powered PD Kits UHBX P1 HDMI RS232 IR PoOH UTP Extender Sender PSE powers Receiver PD UHBX P2 HDMI RS232 IR PoOH UTP Extender Receiver PSE powers Sender PD UMA1215 Rev n c RS RS SS DD A A A A A A A A A HO Copyright 2013 Hall Research Inc All rights reserved 1163 Warner Ave Tustin CA 92780 Ph 714 641 6607 Fax 714 641 6698 HDMI Extender with Power IR and RS 232 Table of Contents LO TET OCT O Peon cecedseit Seance hisdanetscnanaeadisainesdcecnceshdecanesiceasaasdwainesicnus 3 LOT ES ae ee en ie ee ee ne ee Se ne nee et 4 3 0 Model numbers covered in this Manual cccccccecceccesceeceess 4 PUD SU a A E A E E AE T 5 4 1 Package Contents yicescccesinctvvcssisasesennexdsoapsinesdivensie ianiai nana ninnan 5 4 2 Sender CONNECTIONS cccceccesccscceccecceccecceccesceeceeccecceseescascacces 5 4 3 Receiver Connections esesesesessnesereseseseereresesesrsreresesesesesreres 8 4 4 Setting the D
8. al Data Connection If required plug DB9 RS232 cable from source to the connector on the box Typically a straight through male to female cable is used to connect to the sender Pin out of the RS232 connector on the sender is shown below DB9 F Pin Term Direction 2 TX 3 RX Input 5 GND 4 2 3 IR Connections The extender can extend Infra red Remote Control signals in both directions On each box two IR connectors are provided IR Detector and IR Emitter IR Detector Cable As the names imply the IR detector jack requires connection to a compatible IR detector cable This device uses pass thru IR detector cable that maintains the IR modulation Compatible cables are available from Hall Research Model Number CIR DET P2 Pin out Tip Data Ring 5V DC Sleeve GND Figure 5 IR Detector Cable CIR DET P2 Detector eye has adhesive backing IR Emitter Blaster Cables Currently two IR emitter cables are available CIR EMT and CIR EMT2 CIR EMT shown below is recommended for most applications Figure 6 IR Emitter Cable CIR EMT Emitter has adhesive backing Pin out Tip Anode Ring Cathode Sleeve Not Connected An alternative Emitter cable is CIR EMT2 This cable is better suited for situations where there is a need to isolate and confine the IR signal to just UHBX Series one device A separately sold adhesive rubber cover can be used to confine the IR beam to just one target device Th
9. e CIR EMT2 is placed in a cavity in the cover and stuck on the target device directly over its IR sensor A typical application scenario is when several identical video sources are located in close proximity to each other and they need to be independently controlled The CIR EMT2 has a mono type plug Pin out Tip Anode Sleeve Cathode Figure 7 Alternate IR Emitter Cable CIR EMT2 Figure 8 Emitter Cover CIR EMT2 CVR shown with CIR EMT2 4 2 3 Power Connection The senders with PSE suffix have a power input jack whereas the PD senders do not they get power through CAT 6 cable The PSE Sender has a 5vDC power input connector The power input is over voltage protected and reduces the chance of damage if a wrong supply is accidentally plugged in As shipped the package includes a universal power supply with 5vDC 3 2A output Figure 9 Power Supply Model 5 PS5032A shown next to pen for reference HDMI Extender with Power IR and RS 232 4 2 4 UTP Twisted Pair Catx Connection The extender is designed to be used with CAT6 UTP or STP cabling However CATSe cables may be used but the maximum cable length will be reduced by approximately 20 depending on the quality of the cable Augmented CAT6 cables can also be used and are recommended for extension distances exceeding 140 meters or gt 450 feet T568A termination standard is recommended for the UTP cable However T568B will also
10. e extender for repair you must contact HR Support at 714 641 6607 or via email or web To ship the unit back for repair make sure to obtain a Return Material Authorization RMA number o UHBX Series 6 0 Specifications Video Standards DVI single link and HDMI compliant with HDMI 1 4 video specifications including 12 bit color depth 3D video and 4K support Signal type TMDS Connectors Locking HDMI Resolutions DVI signal VGA 640x480 thru WUXGA 1920x1200 HDTV signal 4801 through 1080p Digital Cinema 4K 4096x2160 Not supported in Long Reach Audio Formats All HDMI Embedded Audio including LPCM 7 1CH Dolby TrueHD and DTS HD Master Audio 32 192kHz sample rate Other Signals DDC Pass Thru DDC for reading EDID directly from remotely connected LCD and HDCP handshake CEC Pass Thru DDC for Consumer Electronics Control compatible devices RS232 Bidirectional full duplex any baud rate up to 115 200 IR Extended in both directions Carrier modulation range from 30 KHz to 60 KHz PoH Power over HDBaseT meets IEEE 802 3af standard PD side identifies as Class 2 3 84 6 49 watts Actual power consumption of PD side is 5 5 watts max General Power Supply 100 VAC to 240 VAC 50 60 Hz external 5 VDC 3 2 A regulated Actual DC current powering both PSE and PD sides 1 8A max Power Sender 3 5 watts 12 BTU maximum Receiver 5 5 watts 19 BTU maximum Temp humidity Storage 40 to 158 F 40 to 70 C
11. istance MOde ccc cccccccccccccccseccseeseceeceeeeeeeeeeeeeeeeees 9 45 LED WWGi Cat OFS secesasnscvc comsnstsausenctasemsnaisscbesenasousnitesatencvasosssans DNES 9 5 0 Troubleshooting sic sscsnssasdeinsnstennsssatadoeedenctowaniotaswastesawnaadewesdtansoaneears 10 FS SE CMON S eisene G 11 TRADEMARKS USED IN THIS MANUAL Hall Research and its logo FIRS are trademarks of Hall Research Any other trademarks mentioned in this manual are acknowledged as the property of the trademark owners FCC RADIO FREQUENCY INTERFERENCE STATEMENT This equipment generates uses and can radiate radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio communication It has been designed to comply with the limits for a Class A computing device in accordance with the specifications in Subpart B of Part 15 of FCC rules which are intended to provide reasonable protection against such interference when the equipment is operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at their own expense will be required to take whatever measures may be necessary to correct the interference Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment USA ees Compliant ICA Th O wW Ns
12. work as long as both ends are terminated the same way In EMI noisy environments such as close proximity to power transformers or AC wiring shielded twisted pair STP cable is recommended If STP is used it is important to ensure the RJ45 connector on both ends of the cable have the required metal shroud and that the cable shield drain wire is electrically connected to the metal shroud 4 3 Receiver Connections O LR EMITTER OUTPUT g Q LA O 5V DC DETECTOR UTP Figure 10 Receiver Connections UHBX R PSE shown above 4 3 1 Receiver Video Output Connect the HDMI output to the remote display s HDMI input using high quality HDMI cables Note that the HDMI output connector on the Receiver has a locking nut so that compatible output cables can be positively anchored 4 3 2 Receiver IR UTP and Power Connections Please refer to the description given in section 4 1 since these connections work the same way on both the Sender and the Receiver 4 3 3 Receiver Serial Connection If required plug DB9 RS232 cable from the Receiver to the device being controlled such as a projector or switcher Pin out of the Male RS232 connector on the sender is shown below c UHBX Series DB9 M Pin Term Direction 2 Input 3 RX TX Output 5 GND 4 4 Setting the Distance Mode Mode UTP Length Notes STD Oto 100 m 330ft Default setting L R O to 150 m 500ft Long Reach setting Supports maximum of 1080p 60 Hz
Download Pdf Manuals
Related Search