FRONT PANEL: BACK PANEL:
Contents
1. POWER FUSE In the event of the power fuse having to be replaced first unplug the power cable rom the mains outlet Then remove the fuse cover and replace the power fuse with another fuse of the same type and value Never plug the power cable back into the mains outlet without the fuse cover If the power fuse blows up again when powering on the amplifier take the apparatus to a suitable service centre for repair TECHNICAL SPECIFICATIONS Max Rated Power Loudspeaker 40 Watts RMS 4 Ohms load 10 Speaker Frequency Response Total Harmonic Distortion Signal to Noise Ratio Input Impedance Power Consumption 80 Watts max 85 mV RMS 43 dB 1kHz 39 x 42 x 21 cm 15 4 x 16 5 x 8 3 in 10 7 kg 23 6 lbs Features and Specifications are subject to change without notice Maximum Input Level Dimensions H x W x D 40 GA R 40 GA DSP 3 USER S MANUAL INSTRUCTIONS FOR USE Plug the mains lead into a suitable power socket and connect your instrument to the input socket of the amplifier with a suitable guitar lead this lead is not supplied with the amplifier but is normally supplied with the electric guitar Finally press the Power Switch to the ON position the power LED will light up and your amplifier is ready for use IMPORTANT SAFETY INSTRUCTIONS READ AND KEEP THESE INSTRUCTIONS HEED ALL WARNING e If after you have followed the instructions outlined above your amplifier fails to function please conta2. Chorus e 15 Medium Reverb 1 e 16 Medium wet Delay w multiple repeat USER S MANUAL a 40 GA R 40 GA DSP 11 CD MP3 INPUT This is a line level 1 4 6 3 mm stereo jack into which an MP3 CD Tape player may be connected 12 PHONES This is a 1 4 6 3 mm stereo jack output to connect the headphones When headphones are connected no sound is produced from the speaker 13 POWER LED When this red LED is lit the amplifier is ready to work When it is off it means the amplifier is powered off 14 POWER This switch turns the amplifier on or off CAUTION TO PREVENT ELECTRIC x C SHOCK DO NOT REMOVE TOP OR ez BOTTOM COVERS NO USER SERVICE ABLE PARTS INSIDE WARNING To REDUCE THE RISK OF INPUT 230V 50Hz FUSE TS00mAH 250V FIRE OR ELECTRIC SHOCK DO NOT RISK OF ELECTRIC SHOCK Expose THIS EQUIPMENT TO RAIN OR pW SBA OTOPEN MoisTuRE BACK PANEL WARNING This amplifier must be earthed Please check that the supply voltage details given on the rating label located on the rear panel are in accordance with your electricity supply o MAINS INPUT This is the input socket into which the mains power cable must be connected This amplifier is supplied with a power cable with a moulded on plug If the socket outlets in the home are not suitable for this plug use an appropriate plug adapter that can handle the power required for the amplifier
3. INPUT CLEAN OVERORIVE EQ BVO OOOO u a Volume Troedio Med Pure Md ew Ge 5 3 4 10 aF mm UC 2 12 1 13 0 10 0 10 16 45 14 O INPUT PHONES Para Mid Bass IAMUE Program CD MP3 i INPUT CLEAN E OVERDRIVE EQ 0 10 Mid Volume Gain i Volume Treble OFF RE HOG FRONT PANEL 1 INPUT Plug your guitar in here We recommend that you always use a high quality shielded guitar cable to prevent any background noise interference or unwanted feedback 2 VOLUME This control determines the output volume of the amplifier s clean setting 3 Overdrive GAIN This control determines the distortion intensity of the amplifier s overdrive setting Adding GAIN will make your guitar sound more distorted 4 Overdrive SWITCH This switch activates the amplifier s built in overdrive function which adds distortion to the signal 5 Overdrive VOLUME This control determines the output volume of the amplifier s overdrive setting Adding VOLUME will make your distorted guitar sound louder and clearer 6 TREBLE This control determines the level of high frequencies in the output signal Adding TREBLE will make your guitar sound brighter and sharper 7 MID This control determines the level of middle frequencies in the output signal Adding MID will make your guitar sound rounder and fuller 8 PARAMETRIC MID This control allows you to fine tune your guitar sound by cutting or boosting the mid frequenc
4. ct your dealer Under no circumstances should the amplifier be opened Leave all servicing to qualified personnel e Electrical appliances must never be used in conditions of high humidity or heat To prevent any risk of fire or electric shock never spill or splash liquids on the amplifier Should this happen unplug the power cable from the mains outlet immediately e We would like to draw your intention to the instructions printed on the notice attached to the back of the amplifier CAUTION TO PREVENT ELECTRIC SHOCK DO NOT REMOVE TOP OR BOTTOM COVERS NOUSER SERVICE ABLE PARTS INSIDE CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING To REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE e Exposure to extremely high noise levels may cause permanent hearing damage especially when using headphones Please use this amplifier responsibly for you and your neighbourhood MARKING amp CONFORMITY 1 The CE mark on this product means it conforms to the EMC Directive 89 69 EEC CE marking Directive 93 68 EEC and Low Voltage Directive 72 23 EEC 2 The Crossed out Wheeled Bin is to draw your attention to the WEEE Waste Electric amp Electronic Equipment Directive 2002 96 EC It means this apparatus must be collected separately for recycling 3 RoHS compliant means this device conforms to the Directive 2002 95EC on the restriction of the use of certain hazardous subs
5. tances in electrical and electronic equipments such as Mercury Lead Cadmium Hexavalent Chromium Polybrominated Buphenyl PBB and Polybrominated Diphenyl Esthers PBDE DISTRIBUTOR DEALER cS USER S MANUAL ran 40 GA R 40 GA DSP EMD Music 01 2008 UK Universe al Muse USER S MANUAL GUITAR AMPLIFIER W SPRING REVERB 40 GA R W DIGITAL SIGNAL PROCESSOR 40 GA DSP
6. y parameters of the output signal At a low level the PARAMETRIC MID control will emphasize the lower mids while increasing the level will bring out the upper mids The PARAMETRIC MID control can help you explore a wide variety of different guitar tones 9 BASS This control determines the level of low frequencies in the output signal Adding BASS will make your guitar sound warmer and heavier 10 BUILT IN EFFECT eSPRING REVERB 40 GA R only This is the reverb intensity control This controls the amount of reverb that is added back to the original dry signal Adding REVERB will produce a reverberation effect in your guitar sound as though you were playing in a large hall A little can go a long way in adding that special depth to your sound If engaged the reverb is always active in either overdrive or clean mode eDSP 40 GA DSP only Volume This control determines the mix level of the amplifier s internal DSP effects in relation to the dry signal when DSP is engaged Program This selector enables the user to choose among 16 internal DSP effects 1 Long dry Delay e 2 Flanger short Reverb e 3 Flanger long Reverb e 4 Short Delay w multiple repeat medium Reverb e 5 Medium Delay w multiple repeat long Reverb e 6 Short Reverb 2 e 7 Medium Reverb 2 e 8 Deep Chorus medium Reverb e 9 Normal Chorus short Reverb 10 Short Delay w short repeat 11 Slap back Delay e 12 Cathedral e 13 Large Hall e 14 Short Reverb 1 very light
Download Pdf Manuals
Related Search