Discount-Equipment.com
Contents
1. when it has to be User Manual Version 7576659 English Congratulations on your purchase of the Leica Lino m The safety instructions follow the N A section on how to operate the instrument Before starting up the instrument for the firsttime please read through the entire User Manual paying special attention to the section Safety Instructions Contents Subasio 1 SP 3 Technical amp 12 Safety instructions amp 14 Inserting replacing batteries Slide the locking button forwards to unlock the battery compartment Open the battery compart ment cover and insert the batteries observing the correct polarity Then press the battery compartment cover back down until it engages The battery symbol 9 lights up when the battery voltage is too low Replace the batteries as soon as possible Leica Lino 757665g en e Insert the batteries observing the correct polarity e Use alkaline batteries or rechargeable batteries only e Remove the batteries if the instrument is not to EN be used for a long period of time to prevent corrosion L2P5 L2 Start up Charging first time use e The battery must be charged prior to first use because itis delivered with as low an energy contentas possible e Thepermissible temperature range for charging is between 0 C and 40 C 32 F and 104 F For optimal charging we r2. The instument automatically levels itself within he specified grade range Referto Technical data Press the Lock switch 3 in order to transport or tilt theinstrumentbeyondthe self levellingrange When locked the pendulumis fixed and the self levelling function is deactivated Pulse Power save mode only Lino L360 L2P5 L2 and L2 The instrument is fitted with a Power save mode f particularly good visibility of the laser line is not necessary and you wish to save energy you can switch the Pulse mode on and off by pressing the PULSE POWER SAVE MODE key 2 To be able to detect the laser lines over long distances gt 15 m or in unfavourable lighting condi tions a laser detector can be used The detector is able to locate the laser beam in Pulse mode even over long distances Laserdetectorreferto accessories Leica Lino 757665g en 5 Operation Leica Lino 757665g en Operation How to use the wall mount bracket eica Lino 7576659 en Operation Checking the accuracy ofthe Leica Lino Check the accuracy of your Leica Lino regu nd particularly before important measuring tasks Checking the accuracy ofthe levelling a a e SA 2 5 m A 2 5 m Setthe instrumenton a tripod half way betweentwo walls A B thatare approx 5 Place the Lock switch in the Unlocked gf position Directthe instrument at wall A and switch on the instrument Activate the horizonta
3. acc with IEC 60825 1 2007 Maximum radiation power lt 1 0mW c w Emitted wavelength 620 690nm Beam divergence 1 5 mrad Laser Radiation Do not stare into the beam Laser class 2 in acc with IEC 60825 1 2007 Maximum radiation power lt 1 0mW c w Emitted wavelength 620 690nm Beam divergence 360 Position of label L360 L2P5 L2 LN Ln 4 on n lite 7M r T 4 t E 82d uu i a 1 Lo Leica Lino 757665g en 19 Safety instructions Leica Geosystems AG Heerbrugg Switzerland has been certified as being equipped with a TO quality system which meets the International Standards of Quality Management and Quality Systems ISO standard 9001 and Environmental Management Systems ISO standard 14001 50 150 1400 Total Quality anagement Our commitment to total customer satisfaction Ask your local Leica Geosystems agent for more information about our TOM program Copyright Leica Geosystems AG Heerbrugg Switzerland 2012 Original text 7576659 EN Leica Geosystems AG CH 9435 Heerbrugg Pos Switzerland when it has to be right Leica www leica geosystems com Geosystems
4. ecommend charging the batteries at a low ambient temperature of 10 C to 20 C 50 F to 68 F if possible e lt is normal for the battery to become warm during charging 1 J ack for battery charger Start up Leica Lino 757665g en Keypad and control elements 1 LASERkey 2 PULSE POWER SAVE MODE key 3 Lock switch Display 4 Laser crossline 5 Horizontal laser line G Vertical laser line 7 Locked 3 Pulse Power save mode ON 9 Battery voltage too low AT Plumbing and crossline intersection point e a AK Plumbing point AL Laser switched on EP L2 P3 P5 L2P5 L2 Leica Lino L2 Leica Lino 7576659 en 3 Operation Switching on off Lino L360 L2P5 L2 and L2 Lino P3 and Lino P5 e ON Briefly press the LASER key 1 e ON Move the Lock switch to the right e OFF Press and hold down the LASER key 1 e OFF Move the Lock switch to the left Laser functions Pressing the LASER key 1 activates the following laser functions L360 L360 L2P5 L2P5 L2 12 notinLock notin Lock horizontaland only horizontaland only horizontaland horizontaland 2X only all lines and LSO only only onlyplumbing onlyplumbing horizontal points y horizontal horizontal points points plumbing 3x only vertical againas 1x all points againas 1x onlyvertical onlyvertical againas 1x right le Pla m LL Operation Leica Lino 757665g en Self levelling and Lock functions
5. emperature range The laser switches off and all symbols flash Outside of the self levelling range Thelaserswitches off andthe symbol ofthe function used starts to flash Pendulum locked only Lino L360 L2P5 L2 and L2 Thelaserbeamis notlevelled andthe Locksymbol 7 lights up Leica Lino 757665g en Care and advice on operation Do not immerse the instrument in water Wipe off dirt with a damp soft cloth Do not use aggressive cleaning agents or solvents Treat the instrument with the same care that you would apply to binocu lars or a camera Dropping or violent shaking of the instrument may damage it Check the instrument for any damage before using it Check the levelling accuracy of the instrument regulany Transport To safely transport the instrument setthe Lock switch 3 to Locked Warranty This product comes with a three year warranty from BN Leica Geosystems More detailed information can be found at www leica geosystems com registration All rights reserved for changes drawings descrip tions and technical specifications To receive the three year warranty the product must be registered on our website www leica geosystems com registration within eight weeks of the purchase date If the product is not registered a two year warranty applies Leica Lino 757665g en Operation Technical data L2 CE E PS APA Range wit detector A TOO TOS Accuracy of plumbi
6. l laser line orlaser dot and mark the position of the line or the dot on wall A gt A1 Rotate the instrument by 180 and mark the hori zontal laser line or the laser dot in exactly the same way on wall B B1 Operation Then place the instrument at the same elevation as close as possible to wall A and again mark the hori zontal laser line or the laser dot on wall A gt 2 Rotate the instrument by 180 again and mark the laser on wall B gt B2 Measure the distances of the marked points A1 A2 and B1 B2 Calculate the differ ence of the two measurements If the difference does not exceed 2 mm then the Leica Lino is within tolerance A1 A2 B1 B2 2mm Leica Lino 757665g en Checking the accuracy ofthe horizontalline Checking the accuracy of the vertical line only Lino L360 L2P5 L2 and L2 only Lino L360 L2P5 L2 and L2 Place the Lock switch in the Unlocked gf Place the Lock switch in the Unlocked all position position Position the instrument approx 5 m away from the As reference use a plumb bob and attach it as close wall Direct the instrument at the wall and switch on as possible to an approx 3 m high wall with the LASER key 1 Activate the laser line with the Position the instrumentat a distance of approx LASER key 1 and mark the intersection point of laser 1 5 m from the wall at an elevation of approx 1 5 m crosshairs on the wall Direct the instru
7. ment at the wall and switch on with Swivel the instrument to the right and then to the the LASER key 1 Activate the laser line with the left Observe the vertical deviation of the horizontal LASER key 1 Rotate the instrument and align it with line from the marking If the difference does not the bottom of the plumb line Now read off the exceed 3 mm then the Leica Lino is within tolerance maximum deviation of the laser line from the top of the plumb line If the difference does not exceed 2 mm then the Leica Lino is within tolerance Leica Lino 757665g en 9 o Operation Checkingthe accuracy ofthe vertical plumbing only Lino P3 Lino P5 and Lino L2P5 Place the Lock switch in the Unlocked gl position Checking the upper plumbing point B1 2 2 mm Set up the laser on its tripod or wall mount bracket near point Alsat a minimum distance of 1 5 m from point B1 The horizontal laser is aligned in direction 1 Mark the laser dots A1 and B1 with a pin Operation Rotate the instrument by 180 so that it points in the opposite direction 2 to direction 1 Adjust the instru ment so that the laser beam hits point A1 exactly If point B2 is no further than 2 mm away from point B1 then the Leica Lino is within tolerance Should your Leica Lino be outside of the spec i lerance please contact an authorised dealer shipor Leica Geosystems Display notices Falling below orexceeding the permissible t
8. n use CAUTION Watch out for erroneous measurements if the instrument is defective or if it has been dropped or has been misused or modified Carry out periodic test measurements MA vary after the instrument has been subject to abnormal use and before during and after important measurements Refer to section Checking the accuracy of the Leica Lino Leica Lino 757665g en DEBBIE Safety instructions WARNING i Flat batteries must not be disposed of with household waste Care for the environment and take them to the collection points provided in accordance with national or local regulations y product must not be disposed of with Ed the household waste de Dispose of the product appropriately in accordance with the national regulations in force in your country Always prevent access to the product by unauthorised personnel Product specific treatment and waste management information can be downloaded from the Leica Geosystems home page at http www leica geosystems conytreatment received from the Leica Geosystems dealer WARNING Using a battery charger not recommended by Leica Geosystems can destroy the batteries This can cause fire or explosions Precautions Only use chargers recommended by Leica Geosys tems to charge the batteries Electromagnetic Compatibility EMC WARNING The Leica Lino conforms to the most stringent requirements of the relevant standards and regula tions Yet the po
9. ng 5m Emma OMA Accuracy of horizontal line O Vertical accuracy O 3 m line length 0 75 mm 1 oU o Morizonta 4807 gt 4 UNI 3 5 LL y Number of laser dots Number of laser lines Beam direction vertica up down vertical horizontal up down horizontal up down qu tal horizontal right left 635 nm laser class II 02 lo 635nmleserdassll WIM batery TypeAA TypeAA TypeAA Type AA Batteries pack rechargeable PSN 9x19V 4xt gt V a P54 Protection class spray water dust IP65 Operating temperature 10 C to 40 C Storage temperature 25 C to 70 C S 1 TO __ O BX Dimensions H x D x W o 145 x 130 7 x a 91x 130 7x 99 1x 108 1 x 59 3 mm au 75 4 mm mm 75 4 mm 009 y Weight without batteries with batte 370g 321g 437 2 g 310g 320g ries 1 4 Tripod thread depending on lighting conditions All rights reserved for changes on drawings descriptions and technical data Technical data MOS Leica Lino 7576659 en A 9 P Range with detector SIR O O O Oooo AcurayofplumbingpontG 16 J sie 1167 Se SI Vertical accuracy 10 ft T ESEGESI 4 4fNiAw9 3 5 2 ASS Number of laser dots Number of laser lines Beam direction ver
10. ser beams which are emitted from the instrument It is a Class 2 laser product in accordance with WARNING e EC60825 1 2007 Radiation safety of laser Looking directly into the beam with optical aids products e g binoculars telescopes can be hazardous Laser Class 2 products CAUTION Do not stare into the laser beam or direct it towards Looking into the laser beam may be hazardous other people unnecessarily Eye protection is to the eyes normally afforded by aversion responses including the blink reflex Leica Lino 757665g en DEBA Safety instructions Labelling Laser Radiation Do not stare into the beam Laser class 2 in acc with IEC 60825 1 2007 Maximum radiation power lt 1 0mWc w Emitted wavelength 620 690nm Beam divergence lt 180 Laser Radiation Do not stare into the beam Laser class 2 in acc with IEC 60825 1 2007 Maximum radiation power lt 1 0mW c w Emitted wavelength 620 690nm Beam divergence lt 120 Laser Radiation Do not stare into the beam Laser class 2 in acc with IEC 60825 1 2007 Maximum radiation power lt 1 0mW c w Emitted wavelength 620 690nm Beam divergence lt 180 Laser Radiation Do not stare into the beam Laser class 2 in acc with IEC 60825 1 2007 Maximum radiation power lt 1 0mW c w Emitted wavelength 620 690nm Beam divergence lt 1 5 mrad Safety instructions MS Leica Lino 7576659 en Laser Radiation Do not stare into the beam Laser class 2 in
11. ssibility of it causing interference in other devices cannot be totally excluded Safety instructions FCC statement applic in U S This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful inter ference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be deter mined by tuming the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help WARNING Changes or modifications not expressly approved by Leica Geosystems for compliance could void the user s authority to operate the equipment Leica Lino 757665g en Laser classification The Leica Lino produces visible la
12. tical vertical horizontal horizontal up down right left Laser type 635 nm laser class NiMH paite Batteries recharge Ax15V SS T5 U 4x15V Type AA 3 x 1 5 V able Protection class spray water dust IP65 IP54 Operating temperature 14 F to 104 F Storage temperature 13 F to 158 F 35 6 OZ Weight without batteries with 13 1 oz 11 3 oz 15 4 oz 10 9 oz 11 3 oz batteries Tripod thread 1 4 depending on lighting conditions All rights reserved for changes on drawings descriptions and technical data up down forward up down forward right left vertical horizontal Leica Lino 757665g en Technical data NiMH battery pack L360 rechargeable Art No 790532 Safety instructions The person responsible for the instrument must ensure that all users understand these directions and adhere to them Symbols used The symbols used have the following meanings WARNING Indicates a potentially hazardous situation or an unintended use which if not avoided will result in death or serious injury CAUTION Indicates a potentially hazardous situation or an unintended use which if not avoided may result in minor injury and or appreciable material financial and environmental damage Important paragraphs which must be adhered tO Ir practice as they enable the product to be used in a technically correct and efficient manner Safe
13. ty Instructions Permitted use e Projection of horizontal and vertical laser lines and laser dots ronibitea use e Using the product without instruction e Using outside the stated limits e Deactivation of safety systems and removal of explanatory and hazard labels e Opening of the equipment by using tools screw drivers etc as far as not specifically permitted for certain cases e Carrying out modification or conversion of the product e Deliberate dazzling of third parties also in the dark e Inadequate safeguards at the surveying site Limits of use Refer to section Technical data WA cico Lino is designed for use in areas perma nently habitable by humans Do not use the product in explosion hazardous areas or in aggressive envi ronments Leica Lino 757665g en Areas of responsibility Responsibilities of the manufacturer of the original equipment Leica Geosystems AG CH 9435 Heerbrugg for short Leica Geosystems Leica Geosystems is responsible for supplying the product including the User Manual in a completely safe condition Leica Geosystems is not responsible for third party accessories Responsibilities of the person in charge of the instrument The person in charge of the instrument has the following duties e To understand the safety instructions on the product and the instructions in the User Manual e Tobe familiar with local safety regulations relating to accident prevention Hazards i
Download Pdf Manuals
Related Search