Home

manual

1. uincat Installation Operating and Servicing Instructions Opus 700 Electric Oven Ranges OE 008 0E7010 Please make a note of your product details for future use Date Purchased Model Number Serial Number Dealer OPUS 700 IS 397 ECN 3607 Page 1 of 11 CONTENTS Important Information 2 Warnings and Precautions 3 Technical Data 3 Checklist of Enclosures 3 4 Installation and Commissioning 5 Operating Instructions 5 6 Cleaning 6 7 Servicing Maintenance and Component Replacement 7 9 Fault Finding 10 Spare Parts List 10 Accessories 10 Service Information and Guarantee 11 IMPORTANT INFORMATION Read these instructions carefully before using this product paying particular attention to all sections that carry warning symbols caution symbols and notices Ensure that these are understood at all times WARNING This symbol is used whenever there is a risk of personal injury NOTE This symbol is used to provide additional information hints and tips CAUTION This symbol is used whenever there is a risk of damaging your Lincat product KEEP THIS MANUAL FOR FUTURE REFERENCE IS 397 ECN 3607 Page 2 of 11 WARNINGS AND PRECAUTIONS in accordance with national and local regulations in force in the country of This appliance must be installed commissioned and serviced by a qualified person installation lf the supply cord is damaged it must be replaced by the manufacturer its
2. service agent or similarly qualified person Ensure that the plug socket is accessible at all times Strip plastic coating and clean the appliance before use During operation parts may become hot avoid accidental contact Disconnect this appliance before servicing maintenance or cleaning TECHNICAL DATA Height mm Width mm 900 00 Depth mm 803 Oven Rating kW rT 60 4 0 Hob element individual kW Fan rating W Voltage 3N Amps 3N 4 Total power rating kW 14 CHECK LIST OF ENCLOSURES Warranty card Instructions manual Wire shelves IS 397 ECN 3607 Page 3 of 11 INSTALLATION AND COMMISSIONING This appliance must be earthed Install this appliance on a level surface ensuring all vents are unobstructed Any partitions walls or furniture must be of non combustible material Minimum distances A 100mm B 1000mm see Fig 1 d 0 OW Fig 1 An equipotential bonding terminal is provided to allow cross bonding with other Q equipment If replacing the plug connect the terminals as follows Green and Yellow wire Earth E Blue wire Neutral N Brown wire Live L IS 397 ECN 3607 Page 4 of 11 Means of isolation with at least 3mm contact separation in all poles must be incorporated into the fixed wiring of this appliance The fixed wiring insulation must be protected by insulated sleeving having a temperature rating of 60 Deg C Supply cords shall be oil resistant sheathed fl
3. specified a maximum of 15 minutes of administrative time not spent directly carrying out servicing work is provided for within the warranty Any requirement for staff attending the call to spend greater time than 15 minutes due to administrative requirements such as on health and safety risk assessments will be chargeable at the prevailing rate IS 397 ECN 3607 Page 11 of 11
4. exible cable not lighter than ordinary polychloroprene or equivalent elastomer sheathed cord code 60245 IEC 57 lf this appliance is fitted with castors use caution at all times when manipulating or moving and lock castors when appliance is in position Connection to the electrical supply is made at the rear of the appliance Remove the protective cover and fit a suitable cable to the strain relief Connect to the inlet terminal block This appliance is supplied for connection to a three phase supply OPERATING INSTRUCTIONS Only qualified or trained personnel should use this appliance Fig 2 Before using the appliance for the first time turn the hotplates to full setting for 4 minutes without pans to allow them to cure and harden to maximum durability IS 397 ECN 3607 Page 5 of 11 Refer to Fig 2 Hotplates Switch on the electricity supply the green neon A illuminates The hotplates are controlled by 6 position rotary switched controls E each marked by an individual hob marker D For maximum efficiency always use good quality pans with lids Oven operation Switch on at the main supply and check the green neon A is illuminated Set the oven control B to the desired temperature The amber neon C will illuminate The amber neon extinguishes when the set temperature is reached and then cycles as the element maintains the oven temperature Be aware of the escape of hot air when opening the oven doors Sh
5. lectrical safety Hotplate Switch Remove the facia Remove faulty switch and transfer wires correctly ideally one at a time to new switch Fit new switch to facia and refit facia IS 397 ECN 3607 Page 7 of 11 Fig 4 Thermostat Remove facia and heatshield C Unclip thermostat phial and remove thermostat keeping the insulated sleeving to reuse on the new thermostat Fit new thermostat ensuring capillary is sleeved and routed to avoid internal electrical shorting Refit facia Hotplate Remove facia and heatshield C to access hotplate restraining nut Remove restraining nut and press the underside of the hotplate D up to facilitate easy removal from above Access to the hotplate connection block is now possible IS 397 ECN 3607 Page 8 of 11 Fit new hotplate ensuring wiring connections are correct Replacement is a reversal of the above Oven fans Remove the oven shelves Fig 3 Loosen the fan guard screws and lift off the keyhole slots Remove the hex head nut from the centre of the fan LH thread Remove the fan blade Working from the back of the appliance remove the rear cover Remove the electrical connections from the appropriate motor Remove the 3 securing screws and extract the motor unit Reverse the procedure to fit new motor Contactor Working from the back of the appliance remove the rear cover Remove the electrical connections from the contactor and connect to new contactor U
6. nclip old contactor fit new contactor and rear cover Safety thermostat Remove the thermostat bulb from the top of the oven Working from the back of the appliance remove the rear cover Remove the connections from the thermostat Remove the front control panel and pull the thermostat bulb out and through the oven back Refitting is the reversal of the above Control thermostat Remove the thermostat bulb from the top of the oven Remove the facia and unscrew the thermostat Remove the electrical connections and withdraw the capillary to remove thermostat from appliance Fit new thermostat by reversing the above procedure IS 397 ECN 3607 Page 9 of 11 FAULT FINDING Please refer to the Service Help Desk number on the final page of this manual SPARE PARTS LIST Door bush Braked castor Un braked castor co215 Contactor EL188 Hotplate element lement 4kW lement 3kW H fan motor assembI eee RH fan motor assembl Cable restraint Door handle KN227 Hob control knob KN228 Oven control knob All NE39 Green neon NE40 Amber neon Door seal Oven shelf ven shelf eg spanner ob switch an switch ontrol thermostat afety thermostat All e ACCESSORIES Part Number OA7901 Splashback plate shelf 0E7010 OA7902 Splashback plate shelf OE7008 IS 397 ECN 3607 Page 10 of 11 SERVICE INFORMATION For help with the installation maintenance and use of your Lincat equipment please contact our service departmen
7. t UK 01522 875520 For non UK customers please contact your local Lincat dealer All service work other than routine cleaning should be carried out by one of our authorised service agents We cannot accept responsibility for work carried out by other persons To ensure your service enquiry is handled as efficiently as possible please tell us Brief details of the problem Product code Type number All available on serial plate Serial number Lincat reserve the right to carry out any work under warranty given reasonable access to the appliance during normal working hours Monday to Friday 08 30 to 17 00 GUARANTEE This unit carries a comprehensive UK mainland 2 year warranty The guarantee is in addition to and does not diminish your statutory or legal rights The guarantee does not cover e Accidental damage misuse or use not in accordance with the manufacturer s instructions e Consumable items such as filters glass bulbs slot toaster elements and door seals e Damage due to incorrect installation modification unauthorised service work or damage due to scale food debris build up etc The manufacturer disclaims any liability for incidental or consequential damages Attendance is based on reasonable access to the appliance to allow the authorised technician to carry out the warranty work Service calls to equipment under warranty will be carried out in accordance with the conditions of sale Unless otherwise
8. utdown After use turn all control knobs to the Off position and switch off the mains electricity supply CLEANING AN Do not use a water jet or steam cleaner and do not immerse this appliance Clean all panels with warm water and mild detergent do not use abrasive materials or products containing either chlorine or hydrochloric acid Dry with a soft cloth After cleaning apply a thin film of vegetable oil to the hotplates The oven features removable liners for sides base and top Slide out the top liner and bottom liner and remove the wire shelves Fig 3 by pushing to the rear tilting up at the back then drawing forward Remove the shelf supports by lifting up to disengage Lift off each of the side liners For stubborn deposits a de greasing agent Carbon Off is available from Lincat Replace interior panels correctly after cleaning IS 397 ECN 3607 Page 6 of 11 Fig 3 SERVICING MAINTENANCE AND COMPONENT REPLACEMENT All servicing maintenance and component replacement on this appliance should be carried out by one of our recommended service engineers Replacement of some components requires removal of the facia panel and heatshield see Fig 4 Remove the control knobs A and all screws beneath the facia B Be aware when lowering the facia that electrical connections will still be made When replacing heatshield and facia ensure cables are not trapped After any maintenance check the appliance for e

manual

Contents

Download Pdf Manuals

Related Search

Related Contents