FWT Installation Guide
Contents
1. press enter 6 Screen will appear requesting user name and password Type admin for user name and for password Tick box indicating remember my password Click OK 7 Select 3G Router option on LHS then select Quick set up guide Press apply for admin settings to reset Wait for PC to reset 8 Screen will then read Access Point Status Select Internet Settings WAN Screen reads Wide Area Network Settings If SIM card has pin code then select Use Pin under pin settings 9 Under APN setting select manual APN and type internet be 10 Under dial number type 99 Click Apply Wait for success 3 FREQUENTLY ASKED QUESTION S Make sure you press the power button long enough to switch on the FWT CPE 1 Make sure the battery has been installed 2 properly If the electrical voltage of battery is low please 3 recharge it It may be caused by leaving battery unused for a long time Try to charge for 3 or 5 minutes to restore battery life Check if SIM has been slotted tightly in contact with socket Check if SIM or socket is not covered with dust Check if SIM has not failed or if SIM not deactivated Make sure the network signal is of good quality Make sure the destination number is correct Check if the balance of the SIM account is enough if prepaid Check whether you have not set a Call Limiter If you have set it on make sure the number you dialed is not limited or blacklisted C2. FutureConnect uick Installation Guide Contents FuturePhone 100 FuturePayphone 200 FuturePayphone 400 FutureFax 111 FutureRouter 365 FAQ amp Precautions Quick Installation Guide BTC Mission BTC provides quality telecommunication services for the benefit of our customers and other stakeholders BTC Vision To be a leader in telecommunications in Southern Africa by 2020 Our Values Trust customer focus performance driven accountability and commitment Quick Installation Guide 2 Ensure phone is switched off at back of unit 4 Remove battery sim cover on underside of FuturePhone 100 and insert SIM card in sim card holder Ensure SIM Card inserted correctly Push SIM card holder down until locked in position 6 Replace battery sim cover 8 Connect power supply to AC mains wall socket 10 Refer to User Manual for FuturePhone 100 operational features Li k r AHE 5401129 002 2 40155 INOK d y o l qe OU SI SSODINS Quick Installation Guide FuturePayphone 200 1 Take FuturePayphone out of box 2 Ensure povver svvitch is in OFF position 3 Attach handset to FuturePayphone using RJ11 cable supplied 4 Screw on external antenna Antenna requires only 3 to 3 5 turnsuntil tight Do not over tighten antenna 5 Remove SIM cover on underside of FuturePayphone and insert SIM card Ensure SIM card is i
3. e the actual time is according to the condition of GSM netvvork in the case of no external power supply Ensure the battery is correctly installed by carefully placing the battery in the correct direction of the socket FWT CPE will be charged automatically by the battery when using the external power supply adapter And it will stop automatically when the charging process is completed the battery will still be charged when the power switch is off To enhance the stability of software To solve the problem of software if any It is the responsibility of technical support staff to decide whether the software need to upgrade Ensure that power is switched ON from the mains and the power button is ON Leave it on the charger for 24 hours Position the antenna aerial upright and change position to where good signal strength can be obtained Swith the equipment OFF and then ON Contact BTC Call Centre FutureConnect r mi B T Quick Installation Guide
4. heck whether the antenna indoor and outdoor has been installed properly Adjust the antenna indoor and outdoor of the FWT or move the FWT to the location where better signal can be received If there is still no time indication then contact BTC Call Center to check whether the GSM signal covers the area of the FWT Check whether SIM card has been locked Check whether the PIN code of the SIM card has been activated Check whether the SIM card is not damaged No information on the screen is normal when the FWT is powered off The power supply icon and the blinking battery icon indicate that the battery is being charged The ring indicates that there is an incoming call If you are not in a call you can answer the call Open the battery slot to check whether the battery has been installed properly If the battery has been installed the battery s energy may not be enough Connect the FWT CPE with the external power adapter and charge the battery It indicates that the FWT CPE is powered solely by the battery the battery icon is blinking without any bar inside it indicates that the battery energy level is low Use the power adapter to charge or replace the battery TROUBLESHOOTING WHAT TO DO b Does AC adapter plug properly in the FVVT Does AC adapter plug properly in the electrical outlet or socket Check if it is not a failed battery Supports 3 hour talking time or 90 hours stand by time reference valu
5. nserted correctly Push SIM Card holder down until locked in position 6 Replace SIM Card cover 7 Insert power supply into power input socket on rear of FuturePayphone 8 Connect power supply to AC mains wall socket 9 Switch FuturePayphone on using power switch on rear of FuturePayphone 10 Refer to User Manual for FuturePayphone 200 operational features Quick Installation Guide FuturePhone 400 1 Unpack FuturePhone 400 from box and screvv on external antenna Antenna requires only 3 to 3 5 turns until tight Do not overtighten Ensure phone is svvitched off 3 Remove sim cover on underside of FuturePhone 400 and insert SIM card in sim card holder Ensure SIM Card inserted in correctly Push SIM card holder down until locked in position Replace sim cover 4 Connect power supply to FuturePhone 400 via power input socket at back of FuturePhone 400 Connect power supply to AC mains wall socket 5 Connect USB cable supplied to FuturePhone 400 and to USB port on PC 6 switch on phone 7 Insert CD supplied and follovv set up procedure Click next to finish all set up steps 8 HSPA USB modem icon will show Double click to open 9 Screen vvill shovv four icons vvhich are from Quick Installation Guide FutureFax 111 1 Remove FutureFax 111 from box 2 Insert SIM Card at back of FutureFax 111 3 E
6. nsure SIM inserted correctly and locks in position 4 Ensure SIM Card has been activated for enhanced fax and separate fax number has been allocated to SIM Card by the network 5 Connect external antenna to antenna socket at rear of FutureFax 111 6 Connect fax machine to fax port at rear of FutureFax 111 using RJ11 cable from fax machine 7 Connect optional telephone handset to phone port at rear of FutureFax 111 8 Connect power supply to power socket at rear of FutureFax 111 9 Plug in power supply to AC mains wall socket 10 Refer to FutureFax Quick start guide supplied for operating features and sending and receiving faxes Please note that when sending a fax 01 must be dialled before dialling the recipients fax number 11 The dedicated fax number supplied by the network must be dialled by out side callers when they are sending a fax to the FutureFax 111 It s about knowing that your family is happy 52 B T Quick Installation Guide FutureRouter 365 1 Unpack FutureRouter from box and screw on external antenna Some models have built in antenna 2 Insert sim card in slot marked USIM Card Push gently until sim locks in position 3 Connect Ethernet cable to any LAN port on router and to Ethernet LAN port on PC 4 Connect power supply to router and switch on at wall socket Connect optional handset if required 5 Open web browser on PC and type in static web address 192 168 1 1 and
Download Pdf Manuals
Related Search