Advantech UNO-4683 User Manual
Contents
1. Bit 3 3 2 25 2 2 2 28 2 2 2 20 1 1 1 19 1 1 1 1f 1 1 9 88 7 6 5 4f 3 2 1 1 0 9 88 7 6 5 4f 3 2 1 OF 9 8 7 6f 5 4 3 2f 1 0 User Settings Reserved WDTLOAD Bits Access Name Description 31 8 RO Reserved 0x00 reset 7 0 RO WDTLOAD Current watchdog timer value OxFF reset 47 Appendix B Register 3 WatchDogTimer Control WDTCTL OFFSET 0x008 WDTCTL selects the corresponding event as time out It could be configured to choose reset interrupt or digital output signal when time out Bit 3 3 2 292 2 2 292 2 2 291 11 1 1091 41 1 1191 11 1 9 1897 16 15 1493 2 11 10 1 0 9 897 6 514 3 2 1 059 8 7 695 4 13 210 User Settings Reserved za Sir is m Zz c m Zz Bits Access Name Description 31 3 RO Reserved 0x00 reset 2 R W WDT_DO_E Digital Output Enable for Watchdog N Timer time out 0 Disable digital output 1 Enable digital output 1 R W RESEN Reset Enable for Watchdog Timer time out 0 Disable reset 1 Enable reset 0 R W INTEN Interrupt Enable for Watchdog Timer time out 0 Disable Interrupt 1 Enable Interrupt UNO 4683User Manual 48 Register 4 WatchDogTimer Counter Clear WDTCR OFFSET 0x00C WDTCR clears the watchdog timer Any value written in2. UNO 4683 Intel Core i7 Dual Core Automa tion Computer with 6xLAN 2xCOM 3 expansion slots User Manual Copyright This document is copyrighted 2011 All rights are reserved The origi nal manufacturer reserves the right to make improvements to the products described in this manual at any time without notice No part of this manual may be reproduced copied translated or transmit ted in any form or by any means without the prior written permission of the original manufacturer Information provided in this manual is intended to be accurate and reliable However the original manufacturer assumes no responsibility for its use nor for any infringements upon the rights of third parties that may result from such use Acknowledgements Intel Pentium and Celeron are registered trademarks of Intel Corp Microsoft Windows and MS DOS are registered trademarks of Microsoft Corp All other product names or trademarks are properties of their respective owners Support For more information on this and other Advantech products please visit our websites at http www advantech com For technical support and service please visit our support website at http www advantech com support This manual is for UNO 4683 Part No 2003468300 Ist Edition Printed in Taiwan December 2011 UNO 4683 User Manual ii Product Warranty 2 years Advantech warrants to you the original purchaser that each of its prod ucts wi
3. 3 2 1 OF 9 8 7 6f 5 4 3 2f 1 0 User Settings Reserved WDTRSTCTR Bits Access Name Description 31 8 RO Reserved 0x00 reset 7 0 R W WDTRST Reset Occurrence Frequency CTR Setup A reset issued when the number of times of watchdog timer time out is greater than the value store in WDTRSTCTR 0x00 reset UNO 4683User Manual 52 Register 8 WatchDogTimer Alarm Digital Output WDTALAR MDO OFFSET 0x01C WDTALARMDO is an alarm which indicates whether watchdog timer time out occurs As soon as watchdog timer time out takes place WDTA LARMDO would be set to one till be cleared Bit 313 2 292 2 2 292 2 2 201 11 1 1971 1 1 1911 1 9 897 16 151493 2 1 0 110191857 6 15 453 2 1 059 8 7 695 4 13 291 0 User Settings Reserved is gt gt a is 0 Bits Access Name Description 31 1 Reserved 0x00 reset 0 WDTALAR Watchdog Timer Timer out Alarm MDO 0 reset 1 watchdog time out takes place 53 Appendix B Register 9 WatchDogTimer Interrupt WDTINT OFFSET 0x020 WDTINT is a register indicating whether interrupt is triggered Once read out the value in WDTINT it ll be cleared immediately to avoid looping Bit 3 3 2 292 2 2 292 2 2 291 11 1 1901 41 11 19111
4. Max 2 x 10 100 1000 Base T RJ 45 ports teaming function supported 4x 10 100Base T RJ 45 ports Line out 6 x USB UHCI Rev 2 0 compliant 2 x Front 3x Rear and 1 x Internal ports 3 x Domain I O expansions Only slot 1 sup ports PCle resource Power support for each slot 5V 2A 3 3V 1 5A 12V 0 25A Maximum 30 Watt for all slot condition of 50 C operation temperature Environment Humidity 95 40 C non condensing Operating Temperature IEC 60068 2 2 with 100 CPU I O loading 48 hrs 20 70 C optional for 40 C Safety Cert Temperature 20 50 C 4 122 F Operating Humidity Shock Protection Vibration Protection HDD UNO 4683 User Manual 20 95 non condensing IEC 60068 2 27 CompactFlash 50 G half sine 11 ms HDD 20 G half sine 11 ms EC 60068 2 64 Random 1 Oct min Ihr axis CompactFlash 2 Grms 5 500 Hz 1 Grms 5 500 Hz 1 3 Safety Precautions The following messages informs how to make each connection In most cases you will simply need to connect a standard cable Warning Always disconnect the power cord from your chassis whenever you are working on it Do not connect while the power is on A sudden rush of power can damage sensitive electronic compo nents Only experienced electronics personnel should open the chassis Caution Always ground yourself to remove any static electric charge before touching UNO 4683 Mod l E ern electronic devices a
5. on the equipment should be noted If the equipment is not used for a long time disconnect it from the power source to avoid damage by transient overvoltage Never pour any liquid into an opening This may cause fire or elec trical shock Never open the equipment For safety reasons the equipment should be opened only by qualified service personnel If one of the following situations arises get the equipment checked by service personnel a The power cord or plug is damaged b Liquid has penetrated into the equipment c The equipment has been exposed to moisture d The equipment does not work well or you cannot get it to work according to the user s manual e The equipment has been dropped and damaged f The equipment has obvious signs of breakage DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE MAY GO BELOW v 20 C 4 F OR ABOVE 70 C 158 F THIS COULD DAM AGE THE EQUIPMENT THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT 16 CAUTION DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER DISCARD USED BATTERIES ACCORD ING TO THE MANUFACTURER S INSTRUCTIONS 17 Due to the sensitive nature of the equipment it must be stored in a restricted access location only accessible by qualified engineers 18 When installing this equipment ensure that the Earth cable is securely attached using a 3 5m
6. 1 9 1897 16 15 1493 2 1 10 1 0 9 897 6 514 3 2 1 059 8 7 695 4 13 2510 User Settings Reserved Zz 3 Bits Access Name Description 31 1 Reserved 0x00 reset 0 WDTALAR Watchdog Timer Interrupt Indicator MDO 0 no interrupt triggered 1 an interrupt triggered UNO 4683User Manual 54
7. 232 Serial Ports COM1 2 Pin RS 232 RS 422 RS 485 1 DCD TX DATA 2 RxD TX DATA 3 TxD RX 4 DTR RX 5 GND GND GND 6 DSR 7 RTS 8 CTS 9 RI UNO 4683 User Manual 36 A 3 USB Connectors Table A 4 USB Connector Pin Assignments Pin Signal name Cable Color 1 VCC Red 2 DATA White 3 DATA Green 4 GND Black A 4 DVI I Connector Table A 5 DVI Connector Pin Assignments Pin Signal Name 1 TMDS_C2 2 TMDS_C2 3 GND 4 CRT_DDC_CLK 5 CRT_DDC_DATA 6 MDVI_CLK 7 MDVI_DATA 8 VGAVSY 9 TMDS_C1 10 TMDS_C1 11 GND 12 13 14 VCC_DVI 15 VGA Detect 16 HP_DET 37 Appendix A Table A 5 DVI Connector Pin Assignments 17 TMDS_CO 18 TMDS_CO 19 GND 20 21 22 GND 23 TMDS_CK 24 TMDS_CK C1 VGAR C2 VGAG C3 VGAB C4 VGAHSY C5 GND UNO 4683 User Manual 38 A 5 SATA Hard Drive RAID Support In order to install an operating system onto a RAID volume the RAID option must be enabled in the system BIOS a RAID volume must be cre ated and the F6 installation method must be used to load the Intel Rapid Storage Technology driver during operating system setup Before you start please make sure that two SATA hard drives have been mounted in system A USB floppy will be also required for some addi tional files Enable RAID in Sys
8. 713 For a detailed DVI I pin assignment please refer to A 4 Note Default Display is DVI only UNO 4683 User Manual 20 2 8 Battery Backup SRAM UNO 4683 provides 1MB of battery backup SRAM This ensures that you have a safe place to store critical data You can now write software applications without being concerned that system crashes will erase criti cal data from the memory There is a BTR LED in the front panel of the UNO 4683 please replace the lithium battery with a new one if the BTR LED is activated 2 8 1 Lithium Battery Specifications Type BR2032 Using CR2032 is NOT recommended e Output voltage 3 Voc Location the backside of UNO 4683 board BHI is for real time clock BH2 is for SRAM 21 Chapter 2 2 9 Relay Output for Event To reduce the down time of device or prevent the system fail UNO 4683 provides the relay output function for some events There is a OR gate to handle these events with the relay output The SW9 can enable or disable the linkage of each event with the relay output Adjust the DIP switch ON to enable the linkage of the event with the relay output Table 2 10 Definition of SW9 for events DIP Description of events Remark 1 Fan Failed Optional 2 System Over Temperature Default 90 C 3 BBSRAM Failed Change Battery 4 WDT Alarm By using the relay output UNO 4683 can pass event notifications on to SCADA Some of the parameters can be setu
9. Assignment 35 RS 232 422 485 Serial Ports COM1 COM 36 Table A 3 RS 232 Serial Ports COM1 2 cee 36 USB Eonneclofs seseress reinen airis ee EEP Ena NEon 37 Table A 4 USB Connector Pin Assignments 37 DVI Connector annenin Rn nn 37 Table A 5 DVI Connector Pin Assignments 37 SATA Hard Drive RAID Suppott eeeneeen 39 Watchdog Timer Register seeceeeee 46 UNO 4683 User Manual viii CHAPTER Overview This chapter provides an overview of UNO 4683 s specifications Sections include e Introduction e Hardware Specifications e Safety Precautions e Chassis Dimensions e Packing List Chapter 1 Overview 1 1 Introduction UNO 4683 is an embedded Application Ready Platform ARP that can shorten development time and offers rich networking interfaces to fulfill extensive needs UNO 4683 is designed to be a total solution for network enabled Application Ready Platforms Leveraging field approved and worldwide approved real time OS tech nology Advantech UNO 4683 series provides a Windows XP Embedded ready solution and supports several standard networking interfaces such as Ethernet RS 232 422 485 and more Because of its openness great expansion capability and reliable design fanless and diskless the UNO 4683 series are ideal embedded platforms for implementing custom appli cations for diverse applications Target on Data Server
10. Certifications Dimensions W x D x H Enclosure Mounting Power Consumption Power Requirements Weight OS Support System Design Remote Management System Hardware CPU Memory Indicators Keyboard Mouse Storage Display HDD 1 2 Hardware Specifications EC 61850 3 IEEE 1613 CE FCC Class A UL CCC 2U 440 x 280 x 88 mm 17 3 x 11 x 3 4 fits into standard 19 inch rack SECC 2U Rackmount 60W Typical no added on card AC 90 250 Vac DC 106 250 Vpc With isolation protection AT 6 0 kg WES Windows XP Embedded Windows 2000 XP Windows CE 6 0 Linux QNX Fanless with no internal cabling Built in Advantech DiagAnywhere agent on Windows CE XPe Intel Dual Core i7 620LE 2 0GHz 4G DDR3 SDRAM LEDs for Power IDE Alarm for battery backup SRAM Diagnosis programmable LAN Active Status and Serial Tx Rx 2 x PS 2 connector for Keyboard amp Mouse CF 1 x internal type I II CompactFlash slot HDD Built in one 2 5 SATA HDD bracket DVI I connector SATA HDD extension kit UNOP 1901 AE for 2nd standard 2 5 HDDs RAID 0 1 function support 5 Chapter 1 Watchdog Timer Battery Backup SRAM VO Interface Serial Ports Serial Port Speed LAN Audio USB Ports Expansion Programmable 7 tier event handler from 1 to 255 seconds for each tier 1 MB 2 x DB 9 Automatic RS 485 data flow control 2000 Vpc isolation RS 232 50 115 2 kbps RS 422 485 50 921 6 kbps
11. E D C B A Figure 2 5 RS 232 Jumper Setting UNO 4683 User Manual 18 2 4 6 RS 485 Auto Flow amp RS 422 Master Slave Modes You can set the Auto Flow Control mode of RS 485 or Master Slave mode of RS 422 by using the SW3 DIP switch for COM1 COM2 Please also refer to Table 2 9 for the COM port mapping with the DIP In RS 485 if the switch is set to Off the driver automatically senses the direction of the data flow and switches the direction of transmission No handshaking is necessary In RS 422 if DIP switch is set to On the driver is always enabled and always in high or low status Please refer below for the default setting Table 2 8 SW3 DIP Setting SW3 Status Description ON RS 422 Master mode RS 485 N A RS 422 Slave mode OFF Default RS 485 Auto flow control 2 4 7 Redundant RS 422 Matter In the occasion that UNO 4683 RS 422 ports need to act as multi master in parallel with other RS 422 master ports Because of the auto detection function the TX port will also receive data from other RS 422 master To avoid this situation in this kind of application user can use SW5and SW7 to turn it off then no data will be received from TX port Please refer to the Table 2 11 for the COM port mapping and refer to Figure 2 3 for the location Table 2 9 Mapping table of switches for COM port COM port Switches Status COM1 SW5 ON Normal default COM2 SW7 OFF RS 422 mult
12. and Communication Gateway in Substations Advantech UNO 4683 has been defined and designed to be compliant with IEC 61850 3 which has been defined as an international hardware standard of communication network and system in power substations In modern power substation this standard facilitate the management to large number of devices and enable the various devices to communicate with one another UNO 4683 is a ready and certified platform to serve all these requirement 3x Expansion Slots for Substation Domain IO UNO 4683 offer 3 expansion slots for modularized domain IO plug in card With these expansion slots UNO 4683 can optional equips isolated serial ports IRIG B as well as fiber optical Ethernet interface If user need to plug in the ordinary plug in card UNO 4683 can also sup port the interface module to provide PCI PCIe mini card slot mini PCI and PCI 104 Some of the application need to install 2nd HDD UNO 4683 can also optional provide the HDD kit to install HDD in the expansion slot UNO 4683 User Manual 2 Open Architecture Designed for Automation For applications demanding customized control an UNO 4683 that uses more flexible off the shelf technology is a better option UNO 4683 uses off the shelf components such as an x86 processor an Ethernet chipset CompactFlash and DRAM At the same time the UNO 4683 unit can broadcast the process data through the Ethernet and share the data with operators and manage
13. ely identify the RAID volume This name is case sensitive and can not contain special characters UNO 4683 User Manual 40 10 11 Unless you have selected RAID 1 use the up or down arrow keys to select the strip size and press Enter Press Enter to select the physical disks Select the appropriate number of hard drives by using the up or down arrow keys to scroll through the list of hard drives and press Space to select the drive When finished press Enter rix Manager option ROM v5 7 8 1887 ICH MR Dose 2883 PS Inte Corporat E ALl Rights Reserved ii penato man Vetan 2 Delete RAID Volune 3 Reset Disks to Non RAID Level Strip Size Status Bootabl Volune RAIDA Stripe 128KB 149 168 Yes zan rmysivar DISKS Port Brive Hodel Serial Type Status Vol ID ST988811AS SLYC91PP 5GB ha 2 1988817SH SRRO1P4X thI Select ESC I Exit TENTER Select Manu Select the volume size and press Enter Press Enter to create the volume At the prompt press Y to confirm volume creation Select 4 Exit and press Enter Press Y to confirm your exit 41 Appendix A Install the RAID Driver Using the F6 Installation Method Perform the following steps to install the Intel Rapid Storage Technology driver during operating system setup 1 Press F6 when you see a message in the status line that says Press F6 if you need to install a third party SCSI or RAID driver This message appears at the beginning of Window
14. er Setting i 2 4 6 RS 485 Auto Flow amp RS 422 Master Slave Modes 19 Table 2 8 SW3 DIP Setting 2 4 7 Redundant RS 422 Matter bes Table 2 9 Mapping table of switches for COM port 19 LAN Ethernet Connector DVI I Display Battery Backup SRAM eneesesensensensennnnn NNNN CO UAWN G n w ro e a un vii Table of Contents 2 9 2 10 2 11 Chapter 3 3 1 ww Wh ww ns Appendix A A l A2 A 3 A 4 A 5 Appendix B 2 8 1 Lithium Battery Specifications neeeeneee 21 Relay Output for Event cenennenneennnenennen 22 Table 2 10 Definition of SW9 for events cnnee 22 Advanced Watchdog Timer eneeneeeennn 22 Expansion Slots ceeeseesserseenserseenneennenensnnnen nennen nen 23 Initial Setup esscessssossssonssssonnessnsnesnnnnesnonnenne 20 Eonfiguration san asnieits east 26 Figure 3 1 Location for Configuration eee 27 Install a USB Dongle nnennen 27 Installa Hard Disker 2a esr0 een 28 Figure 3 2 Location of SATA connections 29 Installing in a Rack ennnneneenneennn 30 BIOS Setup and System Assignment enesee 31 System Settings amp Pin Assignments 34 System I O Address amp Interrupt Assignments 34 Table A 1 UNO 4683 System I O Ports 34 Table A 2 UNO 4683 Interrupt
15. g temperature tested under 100 CPU load ing and almost anything an industrial environments demand Designed to Fit Comfortably Into Racks In completely new packaging UNO 4683 has standard 2U rack size as 440 x 280 x 88 mm W x Hx D could fit your rack The rear IO connec tion and indicator LEDs on the front panel for all ports and modes highly simplify monitoring for operation and maintenance in the rack You could easily mount UNO 4683 on rack manage all UNOs in one rack and eas ily develop your application on rack 3 Chapter 1 Popular Operating Systems and Rapid Application Development The Advantech UNO 4683 supports the popular off the shelf Microsoft Windows 2000 NT XP operating systems and the Linux operating sys tem UNO 4683 also features pre built Microsoft Windows XP embedded solutions offering a pre configured image with optimized onboard device drivers Microsoft Windows CE and XP Embedded are compact highly efficient and real time operating systems that are designed for embedded systems without a HDD There is no need to waste time and energy on developing onboard device drivers or using the Platform Builder to build a custom Windows CE image they have all been done for the Advantech UNO 4683 series Through the built in runtime library and Software Development Kit SDK the UNO 4683 series leverages your existing Windows based programming skills to rapidly develop applications UNO 4683 User Manual 4 General
16. gnments Appendix A System Settings amp Pin Assignments A 1 System I O Address amp Interrupt Assignments Table A 1 UNO 4683 System I O Ports Address Range Device 000 01F DMA controller slave 020 03F Interrupt controller 1 master 040 05F 8254 timer counter 060 06F 8042 keyboard controller 070 07F Real time clock non maskable interrupt NMI mask 080 09F DMA page register 0A0 0BF Interrupt controller 2 slave 0CO ODF DMA controller master OFO Clear math co processor OF1 Reset math co processor OF8 OFF Math co processor 1F0 1F8 1st fixed disk 200 218 Digital inputs outputs and counter 278 27F Reserved 2F8 2FF Serial port 2 reserved 380 38F SDLC bisynchronous 2 3A0 3AF Bisynchronous 1 3B0 3BF Monochrome display 3C0 3CF Reserved 3D0 3DF Color graphics monitor adapter 3F0 3F7 Diskette controller 3F8 3FF Serial port 1 reserved UNO 4683 User Manual 34 Table A 2 UNO 4683 Interrupt Assignment Interrupt No Interrupt Source NMI Parity error detected IRQ 0 Interval timer IRQ 1 Keyboard IRQ2 Interrupt from controller 2 cascade IRQ8 Real time clock IRQ 11 Reserved for watchdog timer IRQ 12 PS 2 mouse IRQ 13 INT from co processor IRQ 14 Primary IDE 35 Appendix A A 2 RS 232 422 485 Serial Ports COM1 COM2 12345 00000 OOOO 6 789 Table A 3 RS
17. hapter 2 Hardware Functionality ccccccseeee 10 2 1 Overview Figure 2 1 UNO 4683 Front Panel Figure 2 2 UNO 4683 Rear Panel 2 2 LED Indic lors 4er 2 2 1 System Status Indicators neeeennennn Table 2 1 Definition of System Status Indicators 11 2 2 2 LAN Status Indicators 0 0 ccccccecsseeeecesseessecsseeseeesees 12 Table 2 2 Definition of LAN Status Indicators 12 2 2 3 Serial Communication Status Indicators_ 13 Table 2 3 Definition of Serial COM Status Indicators 13 2 2 4 Indicators for Expansion Slots 2 3 Power INput wossicccacesseccseeinsetecoescecvsuns Table 2 4 AC DC Power Input Table 2 5 AC DC Power Input Function Introduction 14 2 3 1 Specification of the Relay wc eee eects creteeeeeeeees 2 3 2 Wiring Diagram of the Relay nnen Figure 2 3 Event Relay Connection enee 2 4 RS 232 422 485 Interface COM1 COM2 2 4 1 OXuPCI952 UARTs with 128 bytes FIFO 16 2 4 2 RS 422 485 Detection 0 0 cccccssessececesseeseeesseeseeeseens 16 2 4 3 Automatic Data Flow Control Function for RS 485 16 2 4 4 Terminal Resistor SW6 SW8 eeenenene 17 Table 2 6 Jumper setting of terminal resistor 17 Table 2 7 Mapping table of Jumper DIP for COM port 17 2 4 5 RS 232 422 485 Selection Figure 2 4 RS 422 485 Jumper Setting Figure 2 5 RS 232 Jump
18. i master 19 Chapter 2 2 5 LAN Ethernet Connector The UNO 4683 is equipped with 2 Intel 82574L Gigabit Ethernet Con troller which are compliant with IEEE802 3 1000Base T 100Base TX and 10Base T 802 3 802 3u and 802 3ab And it is also equipped with 4 Realtek RTL8100CL Network controllers which are compliant with IEEE 802 3u 10 100Base T CSMA CD standards The Ethernet port provides a standard RJ 45 jack on board and LED indi cators on the front side to show its Link and Active status Please note these LAN controllers all use PCI resource the bandwidth or throughput may be restricted by the PCI bandwidth 2 6 USB Ports The UNO 4683 provides six USB interface connectors which provide complete Plug amp Play and hot swapping for up to 127 external devices The USB interface complies with USB UHCI Rev 2 0 compliant The USB interface can be disabled in the system BIOS setup UNO 4683 provides 2 USB port on the front panel and 3 USB port on the rear panel It also provides 1 USB port inside the chassis for USB dongle key 2 7 DVI I Display UNO 4683 with Intel GMA integrated in Core 17 The UNO 4683 provides DVI I interface powered by Intel Core 17 accel erator It integrates both analog and digital video signal This supports high speed high resolution digital display and traditional analog display You could link your DVI or VGA monitor through a DVI I to DVI and VGA cable Advantech P N 1700004
19. ing two figures show the indicators connectors and expansion slots on the UNO 4683 The following sections give you detailed infor mation about function of each peripheral Figure 2 2 UNO 4683 Rear Panel UNO 4683 User Manual 10 2 2 LED Indicators The LEDs in the front panel can be divided into 4 groups 2 2 1 System Status Indicators SYS FAN BTR OVT FAILWDT HD PWR Table 2 1 Definition of System Status Indicators Item LED Status Description Green System power is on 1 PWR Off System power is off Green Data being received transmitted between on CF SATA 2 HD Off No Data being received transmitted on CF SATA Red WDT trigger the LED for alarm 3 WDT Off Default Red Battery for backup SRAM should be 4 BTR replaced Off Status of battery for backup is OK Red System over temperature alarm 5 SYS OVT Off Default FAN FAIL Red System fan fail 6 Optional Off Default 11 Chapter 2 2 2 2 LAN Status Indicators LAN Activ al 6 5 432 1 6 5 43 2 1 LAN Link Table 2 2 Definition of LAN Status Indicators Item LED Status Description Green 1Gbps network link 1 eo Orange 100Mbps network link Off 10Mbps network link or invalid network link 5 LAN Link Orange 100Mbps network link Port 3 6 Off 10Mbps network link or invalid network link 3 LAN Active Green Ethernet date being received transmit
20. ires More importantly application software previously written for half duplex RS 232 environ ments can be maintained without modification UNO 4683 User Manual 16 2 4 4 Terminal Resistor SW6 SW8 The onboard termination resistor 120 ohm for COM1 COM2 can be used for long distance transmission or device matching Default Open Please also refer to Table 2 9 for the mapping table of Jumper and COM port Table 2 6 Jumper setting of terminal resistor DIP Status Description ON Add terminal resistor on Tx Tx of RS 422 or Data Data 1 of RS 485 OFF No terminal resistor Default 2 ON Add terminal resistor on Rx Rx of RS 422 OFF No terminal resistor Default Table 2 7 Mapping table of Jumper DIP for COM port Jumper for RS 232 SW3 DIP switch Jumper for COM port and RS 422 485 for Auto flow Terminal selection control Resistor COM1 CN12 DIP1 SW6 COM2 CN14 DIP2 sw8 17 Chapter 2 2 4 5 RS 232 422 485 Selection COM1 COM2 support RS 232 RS 422 and RS 485 interfaces The sys tem detects RS 422 or RS 485 signals automatically in RS 422 485 mode To select between RS 422 485 and RS 232 for COMI COM2 adjust CN12 CN14 and Table 2 9 shows the mapping table Jumper settings for RS 422 485 interface CN12 CN14 J H G F EDC B A Figure 2 4 RS 422 485 Jumper Setting Jumper settings for RS 232 interface Default setting CN12 CN14 J H G F
21. lation folders Once Win dows setup has copied these files again remove the floppy disk so that Windows setup can reboot as needed During Windows setup create a partition and file system on the RAID volume as you would on any physical disk If you wish to use the Intel Rapid Storage Technology user interface in Windows you will need to install Intel Rapid Storage Technology by running the Setup exe process after these steps have been completed and the operating system has been successfully installed 43 Appendix A UNO 4683 User Manual 44 Appendix Watchdog Timer Register Appendix B Watchdog Timer Register Register 1 WatchDogTimer Load WDTLOAD OFFSET 0x000 WDTLOAD serves as a countdown timer Once an 8 bit width value is loaded into the register it starts to count down to zero automatically Bit 3 3 2 25 2 2 2 20 2 2 2 20 1 1 1 19 1 1 1 1f 1 1 9 8f 7 6 5 4f 3 2 1 0 1 0 9 8 7 6 5 4f 3 2 1 OF 9 8 7 6f 5 4 3 2f 1 0 User Settings Reserved WDTLOAD Table B 1 WDTLOAD Bits Definitions Bits Access Name Description 31 8 Reserved 0x00 reset 7 0 R W WDTLOAD Load time into the register OxFF reset UNO 4683User Manual 46 Register 2 WatchDogTimer Value WDTVALUE OFFSET 0x004 WDTVALUE saves the current watchdog timer value
22. ll be free from defects in materials and workmanship for two years from the date of purchase This warranty does not apply to any products that have been repaired or altered by persons other than repair personnel authorized by Advantech or which have been subject to misuse abuse accident or improper instal lation Advantech assumes no liability under the terms of this warranty as a consequence of such events Because of Advantech high quality control standards and rigorous test ing most of our customers never need to use our repair service If an Advantech product is defective it will be repaired or replaced at no charge during the warranty period For out of warranty repairs you will be billed according to the cost of replacement materials service time and freight Please consult your dealer for more details If you think you have a defective product follow these steps Step 1 Collect all the information about the problem encountered For example CPU speed Advantech products used other hardware and software used etc Note anything abnormal and list any on screen messages you get when the problem occurs Step 2 Call your dealer and describe the problem Please have your man ual product and any helpful information readily available Step 3 If your product is diagnosed as defective obtain an RMA return merchandize authorization number from your dealer This allows us to process your return more quickly Step 4 Carefu
23. lly pack the defective product a fully completed Repair and Replacement Order Card and a photocopy proof of purchase date such as your sales receipt in a shippable container A prod uct returned without proof of the purchase date is not eligible for warranty service Step 5 Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer iii CE This product has passed the CE test for environmental specifications Test conditions for passing included the equipment being operated within an industrial enclosure In order to protect the product from being damaged by ESD Electrostatic Discharge and EMI leakage we strongly recom mend the use of CE compliant industrial enclosure products FCC Class A This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interfer ence when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Technical Support and Assistance Step 1 Visit the Ad
24. m screw 19 The equipment does not include a power cord and plug The sound pressure level at the operator s position according to IEC 704 1 1982 is no more than 70 dB A DISCLAIMER This set of instructions is given according to IEC 704 1 Advantech disclaims all responsibility for the accuracy of any statements contained herein Safety Precaution Static Electricity Follow these simple precautions to protect yourself from harm and the products from damage To avoid electrical shock always disconnect the power from your PC chassis before you work on it Don t touch any components on the CPU card or other cards while the PC is on Disconnect power before making any configuration changes The sud den rush of power as you connect a jumper or install a card may dam age sensitive electronic components For AC Power Supply The AC power supply cord shall be used with UL approved and one end is plug type and other end is terminal type 18 AWG min For DC Power Supply The DC power supply cable shall be used with UL approved and suit able terminal 18 AWG min A readily accessible approved circuit breaker shall be incorporated in the field wiring UNO 4683 User Manual vi Contents Overview anne esunsternehennnnsnerennen 2 Chapter 1 1 1 Introduction 1 2 Hardware Specifications 1 3 Safety Precautions 1 4 Chassis Dimensions Figure 1 1 Chassis Dimensions 1 5 Packing List nme C
25. nternal temperature damage the plug in card UNO 4683 provide the system temperature alarm function please refer to chapter 2 9 for detail UNO 4683 also support the optional fan for user to resolve the thermal issue of the 3rd party plug in card which is with high power consumption or bad power efficiency It is not recommended to use this kind of card in the embedded system only while the plug in card is mandatory please contact Advantech for this optional support 23 Chapter 2 UNO 4683 User Manual 24 Chapter 3 Initial Setup 3 1 Configuration To open the chassis please follow the steps below 1 Remove all power and signal connections 2 Place the unit with the heat sink side down 3 Remove the plug in module in the slot 3 4 Remove the screws on the cover 5 Install a Well configured CompactFlash Card in this area 6 Install a USB device in this area T Refer to this manual to configure the COM ports A SW9 for Event BH1 for RTC BH2 for SRAM Configuration for COM1 COM2 UNO 4683 User Manual 26 Figure 3 1 Location for Configuration 3 2 Install a USB Dongle UNO 4683 provides a clamp to fix the USB dongle which can be installed inside the chassis Please follow the steps to install the USB don gle and clamp 1 Please follow 3 1 to open the cover for configuration 2 Plug the USB Dongle in the upside port please note the downside port is a dummy port Adjust the posi
26. ntrol Register WDTINTCTR OFFSET 0x014 Based on the watchdog timer time out frequency which is stored in WDTTR WDTINTCTR sets the period of interrupt WDTTR plus one as watchdog timer time out occurred While the number of occurrences exceeds the value saved in WDTINTCTR an interrupt would be issued Bit 3 3 2 25 2 2 2 2 2 2 28 1 1 1 19 1 1 1 19 1 1 9 8f 7 6 5 48 3 2 1 0 1 0 9 897 5 4f 3 2 1 08 9 8 7 6f 5 4 3 25 1 0 User Settings Reserved WDTINTCTR Bits Access Name Description 31 8 RO Reserved 0x00 reset 7 0 R W WDTINTCTR Interrupt Occurrence Frequency Setup An interrupt issued when the num ber of times of watchdog timer time out is greater than the value store in WDTINTCTR 0x00 reset 51 Appendix B Register 7 WatchDogTimer Reset Control Register WDTRSTCTR OFFSET 0x018 Based on the watchdog timer time out frequency which is stored in WDTTR WDTINTCTR sets the period of reset WDTTR plus one as watchdog timer time out occurred While the number of occurrences exceeds the value saved in WDTINTCTR a reset signal would be issued Bit 3 3 2 25 2 2 2 20 2 2 2 20 1 1 1 19 1 1 1 1f 1 1 9 8f 7 6 5 4f 3 2 1 0 1 0 9 8 7 6 5 4f
27. p in the BIOS please check the related function in the BIOS 2 10 Advanced Watchdog Timer The UNO 4683 provides a 7 tier Watchdog Timer for users to have a chance to escalate system status before the forced system reset Each tier has the same time interval from 1 255 seconds and users can have an event handling after the time out of each tier Install the driver from com panion disc and refer to the software manual for details UNO 4683 User Manual 22 2 11 Expansion Slots UNO 4683 offers 3 expansion slots for modularized domain IO plug in card Through the interface card UNO 4683 can also adopt the standard PCI card PCle mini card mini PCI card as well as the PCI 104 card Due to the UNO 4683 is an embedded system the power providing for the expansion slot is limited The maximum power support for each slot are 5V 2A 33V 1 5A 12V 0 25A And totally support maximum 30W at 50 C condition for all slots Before you configure all the module and plug in card please note not to exceed the power limit All the expanding IO modules are design for embedded application the power efficiency and thermal are well controlled But if 3rd plug in card is required to work in the UNO 4683 please check the related power con sumption and working condition carefully In the normal condition the ambiance temperature inside the chassis would be 15 C higher than the environment temperature of UNO 4683 To avoid the abnormal high i
28. re very sensitive to static electric charges Use a grounding wrist strap at all times Place all electronic components on a static dissipative surface or in a static shielded bag Attention If DC voltage is supplied by an external circuit please put a protection device in the power sup ply input port 7 Chapter 1 1 4 Chassis Dimensions Ooo at al oH 1 5 Figure 1 1 Chassis Dimensions Packing List The accessory package of UNO 4683 contains the following items A UNO 4683 B 2 x rack mounting kit C 12 x screw for rack mount kit D 2 x front handles E 4 x screws for front handles F 1x SATA signal cable G 1 x SATA power cable H 4 x screws for SATA HDD installation I 1x clamp for USB dongle J 2x screws for USB clamp K UNO series Driver and Utility DISC L 1 x warranty card UNO 4683 User Manual 8 CHAPTER Hardware Functionality This chapter shows how to setup the UNO 4683 s hardware functions including connecting peripherals set ting switches and indicators Sections include Overview LED Indicators Power Input RS 232 Interface RS 232 422 485 Interface LAN Ethernet Connector USB Ports DVI I Display Battery Backup SRAM Onboard Isolated Digital Input Onboard Isolated Digital Output Onboard Isolated Counter Timer LED amp Buzzer for System Diagnosis PC 104 Chapter 2 Hardware Functionality 2 1 Overview The follow
29. rs By using off the shelf components machine builders can customize the control scheme they use for other machines that require multiple inputs optimized control or Ethernet communica tion So UNO 4683 offers the I O connectivity of PCs with options like 6 x Ethernet 2 x 10 100 1000 Base T 4 x 10 100 Base T 2 x Serial ports 2 x RS 232 422 485 6 x USB ports 2 x Front 3 x Rear x Inter nal 1x CompactFlash and DVI I interface for display panels Robust IO Isolate System from Electrical Noise UNO 4683 is designed for the applications in substation where is sup posed to have certain electric interference Equipping with isolated power and isolated communication ports UNO 4683 has high resistance toward electrical noise It has been proved not only can work well in substation but also suitable for any harsh applications An Industry Proven Design Industrial applications require controllers with high vibration specifica tions and a wide temperature range Controllers in industrial environ ments require flexible and stable mounting and many machine builders underestimate the need for rugged controllers because their applications are mounted in an industrial enclosure UNO 4683 has a special design without the weaknesses of a standard PC No fan and no HDD prevent dust and vibration problems With a smart mechanical design UNO 4683 can meet 50 G shock with CompactFlash 2 G vibration with Compact Flash up to 70 C operatin
30. s XP setup during text mode phase Press F6 if yo Note Nothing will happen immediately after pressing F6 Setup will temporarily continue loading drivers You will then be prompted with a screen asking you to load support for mass storage device s 2 Press S to Specify Additional Device Inve PAD Controlere 8 njolF S220 1GHM SATA RAD Conlrallr 28 Aras ar 2 Ana_o0 2 8 Velmer 38 RAD Hard Dives E Por Q ST980811A5 p Pave STI8IEITSM T iua Hard Drive Member 2 STEEOSITSM Paien Arap Aray _0000 UNO 4683 User Manual 42 Note Note When you see a prompt that says Please insert the disk labeled Manufacturer supplied hardware support disk into Drive A insert a floppy disk containing the following files IAAHCLINF IAAHCL CAT IASTOR INF IASTOR CAT IASTOR SYS and TXTSETUP OEM Use the Floppy Configuration Utility to create a floppy disk with the necessary files or copy required file from driver folder Press Enter Select your controller from the list of available SCSI adapters Use the up and down arrow keys to scroll through the list as all control lers may not be visible Press Enter to confirm your controller and continue At this point you have successfully installed the driver and Windows setup should continue Leave the floppy disk in the floppy drive until the system reboots Windows setup will need to copy the files again from the floppy to the Windows instal
31. tact S5A 250Vac S5A 30Vpc Breakdown Voltage 500V c 50 60Hz Contact Resistance 30mQ maximum Insulation Resistance 1GQ maximum at 500Vpc 2 3 2 Wiring Diagram of the Relay NORMALLY OPEN NO LOAD 1 NORMALLY CLOSED Oe u EN fe Al S A NC Loog COMMON COM Figure 2 3 Event Relay Connection 15 Chapter 2 2 4 RS 232 422 485 Interface COM1 COM2 The UNO 4683 offers two RS 232 422 485 serial communication inter face ports COM1 and COM2 Please refer to Appendix A 2 for their pin assignments The default setting of COMI and COM2 are RS 232 Note Windows usually recognize the COM ports start from COM3 so these two ports might be named as COM3 and COM4 in Windows The function will not be affected and user can also change the name in the Windows Device Manager easily 2 4 1 OXuPCI952 UARTs with 128 bytes FIFO Advantech UNO 4683 comes with Oxford OXuPCI952 UARTs contain ing 128 bytes FIFOs 2 4 2 RS 422 485 Detection In RS 422 485 mode UNO 4683 automatically detects signals to match RS 422 or RS 485 networks No jumper change required 2 4 3 Automatic Data Flow Control Function for RS 485 In RS 485 mode UNO 4683 automatically detects the direction of incoming data and switches its transmission direction accordingly So no handshaking signal e g RTS signal is necessary This lets you conve niently build an RS 485 network with just two w
32. ted Port1 6 Off No Ethernet data being received transmitted UNO 4683 User Manual 12 2 2 3 Serial Communication Status Indicators hi 2 1 Item LED Status Description COM Rx Green Serial port data being received Port 1 2 Off No data being received COM Tx Orange Serial port data being transmitted 5 Port 1 2 off No data being transmitted 2 2 4 Indicators for Expansion Slots Sloti LED Ee ee 15 13 11 9 75 3 1 16 14 12 10 8 6 4 2 These LED indicators are defined by the UNOP series expansion modules please refer to the related document for the definition 13 Chapter 2 2 3 Power Input The UNO 4683 support AC DC power input to fulfill the need of field site Following table shows the specification of the power input Table 2 4 AC DC Power Input AC DC Volt Range Power Rating Connector Type AC 90 250V 2 0 8A 47 63Hz 3Pin Screw Terminal DC 106 250V 2 0 8A 3Pin Screw Terminal The function of each part is described as below Table 2 5 AC DC Power Input Function Introduction Item Function Description AT power switch for AC DC power input Fuse for AC DC power input Screw terminal for AC DC power input AJOJI NJ gt Relay output by event UNO 4683 User Manual 14 2 3 1 Specification of the Relay Relay output type Form C Con
33. tem BIOS Use the instructions included with your motherboard to enable RAID in the system BIOS 1 Click Del to enter the BIOS Setup program after the Power On Self Test POST memory test begins Click the Integrated Peripherals menu Click the OnChip IED Device menu Switch the SATA Mode option to RAID to enable Intel RAID Technology Click F10 to save the BIOS settings and exit the BIOS Setup pro gram 39 Appendix A Create a RAID Volume Use the following steps to create a RAID volume 1 2 3 When the Intel Rapid Storage Technology option ROM status screen appears during POST press Ctrl and i at the same time to enter the option ROM user interface tel R Natrix SUGAR Manager option ROM v5 2 8 1087 ICH2MR Copyright C 2003 85 Intel Corporation All Rights Reserved MID Volunes None defined Physical Bisks Port Brive Model Serial ST988B11AS SLYCOIPP 2 STORARIISH SRROLPAX Press e 0 enter Configuration Utility Select 1 Create RAID Volume and press Enter p TERTI UNUU UENO mA 1 Create RAID Volune G suicie mis VUIURU 3 Reset Disks to Non RAID fe Exit Type Status Vol IB Non Use the up or down arrow keys to select the RAID level and press Enter CREATE VOLUME MENU Nane RAID Level RAIDA Stripe Disks Select Disks Strip Size 128KB Capacity 149 1 GB Create Volune Enter a string between 1 and 16 characters in length that can be used to uniqu
34. tion of the kit to fasten the USB dongle and then screw to fix the kit 27 Chapter 3 3 3 Install a Hard Disk Please follow the steps below to install an HDD 1 Turn the heat sink side down 2 Unscrew the screws and get the HDD bay apart 3 Insert the HDD into the HDD bay and screw it UNO 4683 User Manual 28 4 Connect the SATA cable between HDD and connector then assem ble the HDD back to the chassis The locations of the connectors are below HDD Bay Figure 3 2 Location of SATA connections 29 Chapter 3 3 4 Installing in a Rack UNO 4683 provides the kits for Rack mounting in the accessory box 1 Please screw the ears and handles at the position indicated below The same on the other side 2 3 UNO 4683 equips the Aluminum Fins on the top of the unit as heat sink It can generate nature convection for better heat trans mission For optimal thermal performance leave 2U 88 9mm space height on the top of the unit UNO 4683 User Manual 30 3 5 BIOS Setup and System Assignments UNO 4683 adopts Advantech s SOM 5788 CPU module Further information about the SOM module can be found in SOM s user s manual You can find this manual on the UNO 4683 s companion DISC Please note that you can try to LOAD BIOS DEFAULTS from the BIOS Setup manual if the UNO 4683 does not work properly 31 Chapter 3 UNO 4683 User Manual 32 A Appendix System Settings and Pin Assi
35. to WDTCR would set zero and reload the value stored in WDTLOAD register to watchdog timer Read reset WDTCR is undefined Bit 3 3 2 28 2 2 2 25 2 2 2 20 1 1 1 1f 1 1 1 1f 1 1 9 8f 7 6 5 4f 3 2 1 0 1 0 9 8H 7 6 5 4f 3 2 1 OF 9 8 7 6f 5 4 3 2f 1 0 User Settings WDTCR Bits Access Name Description 31 0 wo WDTCR Watchdog Timer Clear any value clear watchdog timer 49 Appendix B Register 5 WatchDogTimer Time Out Trigger Status WDTTR OFFSET 0x010 WDTTR saves the occurrence times of watchdog timer time out The cor responding operation differs from the access type which is taken on WDTTR A read out from WDTTR would clear the watchdog interrupt while a write in clear WDTTR Bit 3 3 2 25 2 2 2 20 2 2 2 2 1 1 1 11 1 1 1f 1 1 9 8f 7 6 5 4f 3 2 1 0 1 0 9 8 7 6 5 4f 3 2 1 Of 9 8 7 6f 5 4 3 2f 1 0 User Settings Reserved WDTTR Bits Access Name Description 31 8 RO Reserved 0x00 reset 7 0 R W WDTTR Watchdog Timer time out counter The correlative operation is upon the access type OxFF reset Read out clear the watchdog interrupt Write in clear WDTTR UNO 4683User Manual 50 Register 6 WatchDogTimer Interrupt Co
36. vantech web site at www advantech com support where you can find the latest information about the product Step 2 Contact your distributor sales representative or Advantech s cus tomer service center for technical support if you need additional assistance Please have the following information ready before you call Product name and serial number Description of your peripheral attachments Description of your software OS version software etc A complete description of the problem The exact wording of any error messages UNO 4683 User Manual iv Safety Instructions l 2 3 Read these safety instructions carefully Keep this User s Manual for later reference Disconnect this equipment from any AC outlet before cleaning Use a damp cloth Do not use liquid or spray detergents for clean ing For plug in equipment the power outlet socket must be located near the equipment and must be easily accessible Keep this equipment away from humidity Put this equipment on a reliable surface during installation Drop ping it or letting it fall may cause damage The openings on the enclosure are for air convection Protect the equipment from overheating DO NOT COVER THE OPENINGS Make sure the voltage of the power source is correct before con necting the equipment to the power outlet Position the power cord so that people cannot step on it Do not place anything over the power cord All cautions and warnings
Download Pdf Manuals
Related Search