User manual WATER BOILER METOS MARINE WKI
Contents
1. A Filling pipe B Tea filter with disk C Blender transport disk D Container and lid Dh The inner pot of the container must always be fresh and clean 2 To avoid temperature loss during the brewing process we recommed you to pre heat the container by putting the cable into a power socket Filling the container with approx 2 litres of hot water and switch on the container for at least 10 minutes before the brew starts The indication lamp on the container will light up 3 Put the tea loose or in bags in the tea filter approximately 6 grams per litre 4 Insert the tea filter into the disk already placed in the container 5 Tap the water from the container Place the filling pipe on the tea filter and the disk Then position the swivel arm over the pipe 27 10 2015 6 Fillthe water boiler with the required quantity of water and wait until the water has reached the temperature set Open the tap as far as possible allowing it to vent properly Afterwards the flow can be reduced to a level that can be processed by the water distributor on the filter Adjust the flow rate so that the container fills up in approx 5 to 6 minutes 7 O2. 7 32 Electrical connection 2 2 nn n anne eee ees 7 3 3 Water connection iss su ea oe da oe ee eee ewe UE Ge See ee 8 3 4 Wateraralage cites ne avian Mite awe see cue ea nee gels Oho ee arate ee er oa 8 3 0 Mounting the WKI the o o oooooononono nooo 8 4 CONTROL PANEL suas sun ee adia ces FO ag ee O nen pepa 9 5 PREPARATIONS BEFORE USE 9 6 USE 10 6 1 Brewing coffee O Se A Scar 10 6 2 Brewing 11 7 MAINTENANCE a hace a age Eee ES 11 7 1 SEE EO E E ees 11 7 2 de nen a aw eae o e Ge eee eae ee eee Ga eh 12 8 DRT BOI PROTECTION 12 9 TRANSPORTATION asia 4 44 24 0 ana dr de in SS 13 General sign for IMPORTANT WARNING OR REMARK N Warning for possible damage and or injury to machine or operator IN Warning for electricity and or steam hazard metos 27 10 2015 Water boiler Metos Marine WKI These operating instructions are intended for the user of the ANIMO storage water boilers type WKI Read these operating instructions carefully to ensure that appliance is used properly and safely 1 GENERAL DESCRIPTION A storage water boiler of the WKI range makes constant hot water always available All WKI boilers are mains connected An adjustable thermostat keeps water at a const
3. Water boiler Metos Marine WKI Type Article number Buffer stock hot water Hour capacity hot water Heating time 20 97 Tapping speed Electrical connection Output Fuse 3N 380 415V Fuse 3 230V Cold water connection Min Max pressure Overflow connection Cord length Dimensions Weight empty filled WKI 40n 30125 40 Itr 320 cups 90 Itr 720 cups 23 min 6 9 seclltr 3N 380 415V 50 60Cy 9600W 3x 16A 35A 3 4 1 8 bar O15 mm 1 5m see fig 2 17 kg 61 kg Technical alterations are reserved WKI 60n 30130 60 Itr 480 cups 90 Itr 720 cups 35 min 6 9 seclltr 3N 380 415V 50 60Cy 9600W 3x 16A 35A 3 4 1 8 bar O15 mm 1 5m see fig 2 19 5 kg 82 5 kg 27 10 2015 WKI 80n 30135 80 Itr 640 cups 180 Itr 1440 cups 25 min 6 9 seclltr 3N 380 415V 50 60Cy 19 2kW 3x 16A 3x 35A 3 4 1 8 bar 215 mm Lom see fig 2 24 kg 107 kg WARNING N When the appliance is in use some of the components will get very hot Always remove the plug from the socket if the machine has to be opened for repair or maintenance Always observe local rules while installing the unit and use approved materials and parts Do not put the machine in areas where the temperature drops below freezing point because there is always water left in the system Always plug the machine into an earthed wall socket Do not submerge or spray the machine Have all repairs carried
4. boiler is now ready for use When drawing off hot water the orange filling switch must be turned off so that cold water car no longer flow into the boiler The quantity of water to be added to and or drawn off can be checked using the volume scale next to the gauge glass In the event of breakage or repair work the gauge glass can be shut off by closing the gaug glass tap fig 1J The water temperature is easy to read from the thermometer When drawing off water using the swivel arm tap open the tap as far as possible allowing it t vent properly Afterwards the flow can be reduced to a level that can be processed by the water distributor on the filter After use both switches must be turned off shutting off the water supply and electricity It is possible to keep water at a temperature of at least 60 C overnight but it is important to make sure that the orange filling switch has beer turned off meios 27 10 2015 6 USE Brewing coffee see section 6 1 Brewing tea see section 6 2 Always apply the following safety precautions with a WKI when making use of a serving trolley setup Always park the serving trolley straight between the parking rails After parking the serving trolley always put the brake on the right hand swivel wheel Plug in the cable in the inlet socket on the back of the container put the plug in the power socket and switch the container on The container now starts heating After the
5. filter has been drained turn the swivel arm away from the filter remove the filter and immediately place the lid on the container Before transporting the serving trolley always remove the cable with plug between the power socket and the container 6 1 Brewing coffee Et Fig 7 A Filter lid with water distributor B Combi filter with basket filter insert C Blender transport disk D Container and lid m etos Water boiler Metos Marine WKI Basic rules for brewing coffee e Use regular ground coffee 50 gram litre e Keep the containers and the filters clean 1 The inner pot of the container must always be fresh and clean 2 To avoid temperature loss during the brewing process we recommed you to pre heat the container by putting the cable into a power socket Fil the container with approx 2 litres of hot water and switch on the container for at least 10 minutes before the brew starts The indication lamp on the container will light up 3 Tap the water from the container and place the blender into the container 4 Place a basket filter paper into the filter with the appropriate amount of coffee normal medium ground The coffee must be evenly spread over the filter Generally speaking you will need about 45 50 grams per litre 5 Place the filter lid on the filter put the filter on the container and position the swivel arm over the centre of the filter lid 6 Fill the water boiler with the required qua
6. out by a specially trained technician If the machine is not used it is advisable to remove the plug from the socket and to turn off the water tap 3 INSTALLATION This appliance may only be positioned and connected by a qualified sevice engineer e Preparation for positioning Electrical connection Water connection e Water drainage e Mounting the WKI on the wall see 3 1 see 3 2 see 3 3 see 3 4 see 3 5 3 1 Preparation for positioning e The preparation to install must be done by a specially trained technician Always observe local rules while installing the unit and use approved materials and parts e The technician may only make the connection of the machine to the wall 3 2 Electrical connection Depending on the model the WKI should be connected to single phase or rotatory current The wall socket and the main switch secured group are part of the electricity installation It is not allowed to connect other users to that group Depending on the appliance s electrical execution it must be connected as below metos 27 10 2015 e fig 3 In case of 3N 380 415V 5 core cable e fig 4 In case of 3 230V 4 core cable e fig 5 In case of IN 220 230V 3 core cable The following points should be observed when wiring a new plug 1 The green yellow coloured wire EARTH should be connected to the terminal which is either marked with the letter E the earth symbol 1 or colo
7. ant pre set temperature It refills automatically when water is drawn off In figure 1 the main parts are indicated Figure 1 A Thermometer H Filling switch B Tap with swivel arm Dry boil protection C Adjustable thermostat J Gauge glass tap D Cold water connection K Gauge glass E Electrical connection L Litre index F Overflow connection M Desaeration G On off switch The storage water boiler is supplied with the following accessories Operating instructions Swivel arm Water tube 1 5 m 2 TECHNICAL DETAILS Type Article number Buffer stock hot water Hour capacity hot water Heating time 20 97 Tapping speed Electrical connection Output Fuse 1N 220 240V Fuse 3N 380 415V Fuse N 230V Cold water connection Min Max pressure Overflow connection Cord length Dimensions Weight empty metos WKI 10n 30110 10 Itr 80 cups 30 Itr 240 cups 24 min 6 9 sec ltr 1N 220 240V 50 60Cy 3200W 16A 3 4 1 8 bar 015 mm 1 3 m see fig 2 8 kg 1 sachet descaling agent 48 sachets for 50 grams art nr 49007 WKI 20n 3kW 30115 20 ILtr 160 cups 30 Itr 240 cups 45 min 6 9 sec ltr 1N 220 240V 50 60Cy 3200W 16A 3x20A 3 4 1 8 bar 15 mm 1 3m see fig 2 11 kg WKI 20n 6kW 30120 20 Itr 160 cups 60 Itr 480 kopjes 23 min 6 9 sec ltr 3N 380 415V 50 60Cy 6600W 3x10A 3x20A 3 4 1 8 bar O15 mm 1 5 m see fig 2 11 kg
8. follows 1 Allow the appliance to cool down 2 Unscrew the protective cap 3 Press the button which is now visible and firmly screw the protective cap back on If the dry boil protection triggers owing to increased scale deposits descale the appliance See chapter 7 2 Consult your dealer if the fault was caused by a problem other than the dry boil protection being triggered Water boiler Metos Marine WKI 27 10 2015 9 TRANSPORTATION Before transporting the WKS carry out the following actions 1 Switch off the WKI and remove the plug fitting from the wall socket 2 Close the water supply tap and disconnect the connection hose 3 Remove the bottom plate by unscrewing the fastening bolt in the middle of the plate 4 Once the hexagonal plug has been removed from the red drain tap the drain tap can be used to completely drain the water boiler Remove the water boiler from the wall Replace the parts mentioned in points 3 and 4 The WKI is now ready for transportation When reinstalling the water boiler carefully follow the instructions indicated in the Installation chapter oo Ss metos metos kitchen intelligence
9. meios WATER BOILER METOS MARINE WKI MG4164349MW 4164349 4164354 4164356 User manual 27 10 2015 27 10 2015 Water boiler Metos Marine WKI m fig 1 Abb 1 E NEY Wh py A metos Water boiler Metos Marine WKI 27 10 2015 Electrical connection we ter connection 4 Overflow connection 27 10 2015 Water boiler Metos Marine WKI This appliance is in accordance with the EMC Directive 89 336 EEC 92 31 EEC and the low voltage directive 73 23 EEC Animo has the right to change parts of the machine at any time without advice or direct announcements to the client The contents of this manual can also be changed without any announcements This manual is to be used for the standard model type of the machine Thus Animo cannot be held responsible for any damage resulting from the application of this manual to the version delivered to you For extra information on adjustments maintenance and repair contact the technical department of your supplier This manual has been written very carefully However Animo cannot be held responsible neither for mistakes in the book nor for their consequences metos Water boiler Metos Marine WKI 27 10 2015 TABLE OF CONTENTS 1 GENERAL DESCRIPTION summen eee eens 6 2 TECHNICAL DETAILS ses cnc nda be Es eee eee ee ye oes ee Se bes Den 6 3 INSTALLATION ee DR HR nite nn e 7 3 1 Preparation f r DOS MONTTO ERA de darse
10. nce the water level in the water boiler has reached 0 the tap can be closed and the water boiler can be refilled and heated for the next brew 8 Remove the pipe and the tea filter after the tea has been made 9 ATTENTION After brewing put the lid on the container to avoid loss of temperature and taste The optimum extraction time is minimally 4 minutes and maximally 15 minutes After more than 15 minutes the flavour of the tea decreases 10 Rinse the tea filter immediately after use Attention Always place the blender transport disk and the lid when transporting the container by hand or serving trolley this prevents spilling from the container 7 MAINTENANCE WARNING N Do not leave the unit during maintenance Always follow the instructions which are supplied with the used scale remover It is advisable to wear safety glasses and gloves during descaling After descaling run the appliance through at least three cycles Wash your hands after descaling Do not submerge or spray the unit Have all repairs carried out by a qualified technican See section 7 1 See section 7 2 e Cleaning daily e Descaling 7 1 Cleaning daily e Clean the outside of the appliance with a clean damp cloth if necessary using a mild non abrasive cleaning agent e Do not use an abrasive as this will leave scratches and dull spots metos 27 10 2015 WARNING To descale the WKI the appliance needs to be o
11. ntity of water fig 1H switch on the heating system fig 1G and wait until the water has reached the temperature set Open the tap as far as possible enabling it to vent properly Afterwards the flow can be reduced to a normal level Adjust the flow so that the water does not run over the distributor tray in the filter lid Doing this will ensure that the right filtering speed has been set 7 The brewing process is starting the blender in the container guarantees a uniform quality of the coffee which makes stirring the coffee with loss of time temperature and aroma unnecessary The temperature of the coffee is kept at a temperature of 80 85 C The storage time of the coffee is determined by the blend of coffee and is usually 1 1 5 hours 8 Once the water level in the water boiler has reached 0 the tap can be closed and the water boiler can be refilled and heated for the next brew 9 After the coffee has been made and the filter has leaked out the latter can be removed and the lid can be placed on the container 10 Rinse the filter after use Attention Always place the blender transport disk and the lid when transporting the container by hand or serving trolley this prevents spilling from the container Water boiler Metos Marine WKI 6 2 Brewing tea A tea filter with disk and a filling pipe is needed to brew tea in a container optional in combination with WKI
12. or safety reasons 5 Switch the water boiler on again allow it to fill until all scale deposit has been completely submerged 6 Switch on the heating system and heat the water to a temperature of approx 60 C 7 Read the warnings and other instructions indicated on the Animo scale remover m etos Water boiler Metos Marine WKI 8 Add the scale remover to the heated water Please note once the scale remover has been added the water will start to foam In extreme cases where too much scale remover has been used the foam may flow over the edge of the water boiler 9 When no more scale remover is required no foaming occurs when more scale remover is added drain the water boiler via the tap In the event of obstinate boiler scale repeat steps 5 9 10 Repeat steps 1 4 in order to drain the water boiler 11 Once all boiler scale has been removed rinse the water boiler thoroughly with clean water not forgetting to also rinse the tap 12 The water boiler is now ready for use again 8 Dry boil protection This appliance is equipped with a dry boil protection This protection triggers if the heating element overheats owing to a fault Once the fault has been resolved the dry boil protection can be reset at the left side of the appliance fig 11 The most common cause of the dry boil protection being triggered is not descaling the heating system in time If the heating system does not switch back on proceed as
13. pened and partly disassembled As a result components are opened up that have a high voltage and are not covered Always disconnect before opening the appliance 7 2 Descaling During operation scale will form in the machine Therefore the machine needs to be descaled regularly to guarantee the lowest energy consumption and proper functioning WARNING e Since the drain tap is located in the electrical part of the water boiler users are advised for safety reasons not to descale the hot water boiler themselves When to descale Depending on the use and hardness of the water we advise you to have the WKI descaled by a service technician every 5 or 6 months Depending on the frequency of usage and the hardness of the water we advise you to inspect the appliance regularly for scale formation Remove the cover of the water boiler regularly If there is loose scale grit on the bottom or if there is severe scale formation on the walls then the unit needs to be descaled Descaling procedure for the service engineer 1 Switch off the appliance and remove the plug from the socket 2 Remove the bottom plate by unscrewing the fastening bolt in the middle of the plate 3 Once the hexagonal plug has been removed from the red drain tap the drain tap can be used to completely drain the water boiler Any loose boiler scale will then be removed 4 Close the red drain tap replace the hexagonal plug and bottom plate f
14. r should be mounted with the help of fig 2 6 4 Mount the storage water boiler on the wall and connect electricity water supply and water drain 5 Place the combination of the serving trolley container combi filter under the tap with swivel arm Water boiler Metos Marine WKI 4 CONTROL PANEL FIG 1 A Thermometer C Adjustable thermostat G On off switch Filling switch K Gauge glass 5 PREPARATIONS BEFORE USE When placing and connecting the appliance the following instructions should be followed 1 Open the manual stopcock part of the water connection and check if the connections do not leak Plug in the water boiler and press the orange filling switch fig 1H The water boiler will now start to fill As soon as the water becomes visible in the gauge glass the heating system can be switched on press the green on off switch fig 1G The water boiler will now start to heat up Allow the water boiler to reach the required level in the gauge glass fig 1K and then stop the water supply by pressing the orange filling switch again If the water supply is not turned off on time The built in floating mechanism will automatically shut off the water supply when the maximum capacity has been achieved 27 10 2015 The thermostat can be used to heat the water tc any temperature between 30 C and 97 C The ideal water temperature when making coffe is approx 97 C The water
15. ured green green yellow 2 The blue coloured wire NEUTRAL should be connected to the terminal which is either marked with the letter N or coloured black 3 The brown and black coloured wires LIVE should be connected to the terminals which is either marked with the letter L1 L2 and L3 or coloured red Green yellow Earth E Blue Neutral Brown Live L1 Black Live 12 Grey Live L3 fig 3 Green yellow Earth E Brown Live L1 exe Black Live 2 Grey Live L3 fig 4 Green yellow Earth E Blue Neutral Brown Live L1 fig 5 metos Water boiler Metos Marine WKI 3 3 Water connection The system must be a stopcock a drain a non return valve and must end with an easily accessible aeration tap with a 3 4 connector The minimum water pressure must not fall below 1 bar with 5 I min flow pressure 3 4 Water drainage The overflow connection 15 mm of the WKI must be connected to the water drainage 3 5 Mounting the WKI on the wall Mount the appliance on the wall using plugs suitable for the purpose In case of cellular concrete plasterboard or similar walls of other materials screw right through them or apply extra wall reinforcement 1 The local voltage should correspond with the specifications indicated on the type plate 2 Determine the complete setup of the serving trolley s with the storage water boiler WKI 3 Determine where the storage water boile
Download Pdf Manuals
Related Search