HMI Hardware
Contents
1. General Precaution Use Restriction products are not authorized for use in supporting systems aircraft navigation control systems military systems and any other application where performance failure could be life threatening or otherwise catastrophic Disassembling or Modification Do not disassemble or modify LCD module It may damage sensitive parts inside LCD module and may cause scratches of dust on display Manufacturer does not warrant the module if customers disassemble or modify LCD module Breakage of LCD display LCD display is broken and liquid crystal spills out do not ingest or inhale liquid crystal and do not contact liquid crystal with skin If liquid crystal comes in contact mouth or eyes rinse out with water immediately If liquid crystal comes in contact with skin or clothes wash it off immediately with alcohol and rinse thoroughly with water Handle carefully any chips of glass it may cause injury when glass is broken Absolute ratings not exceed the absolute maximum rating values such as supply voltage environment temperature etc otherwise LCD module might get damaged Please do not leave LCD module in the environment of high humidity and high temperature for long time It is recommended to employ protection circuit for power supply Operation Do not touch push or rub the LCD display surface with any thing harder than HB pencil lead Use fingerstalls of soft gloves2. 3 by replacing power supply board after replacing power board the label for marking power input range located on the enclosure has to be changed 3 3 Reserved 3 4 Accessories part numbers WPG045 Gasket for HMI 4 3 For dust and Moisture protection Gasket for HMI 7 LOW COST HMI 7 HIGH WPGO073 PERFORMANCE For dust and Moisture protection WPG105 Gasket for HMI 10 For dust and Moisture protection WPG155 Gasket for HMI 15 For dust and Moisture protection HMB045 HMI Mounting Brackets 4 4 1 Installation Installation Guidelines Stainless steel front HMI has sharp edges and more weight Enough care should be taken while inserting HMI into enclosure panels using proper hand gloves Improper handing may cause injury personal during installation of HMI into enclosure panels 1 10 11 12 13 14 The HMI is intended for indoor use and not in any hazardous area HMI device should be installed in suitable enclosure panels cabinets housings Avoid facing of HMI screen directly exposed to sun light Avoid installation in high vibration area moving parts Avoid installation near to high radiation noise emitting devices like motors transformers variable frequency drives inverters UPS cellular towers etc Avoid installation in areas where there is the presence of vapors gases oils lubricants chemicals etc Install HMI at suitable height and location which is easy accessibl
3. in order to keep clean display quality When LCD display surface is dusty please wipe gently with absorbent cotton or other soft material Wipe off saliva or water drops as soon as possible If saliva or water drops contact with polarizer for a long time they may cause deformation or color fading When cleaning the adhesives please use absorbent cotton wetted with a little petroleum benzene or other adequate solvent Static Electricity film must remove very slowly from the surface of LCD module to prevent from electrostatic occurrence Persons handle the LCD display should be grounded through adequate methods Strong light exposure The LCD display shall be not exposed to strong light such as direct sunlight LCD display characteristics may be changed Disposal 7 wren disposing LCD module obey the local environmental regulations 1 2 Standards Certificates and Approvals The table below shows the approvals that may be available Description Details O O UL approval UL 508 and CSA C22 2 No 142 Low Voltage Directive 2006 95 EC EMC Directive 2004 108 EC Requirements for Emission EN 61000 6 4 2007 Requirements for Interference EN 61000 6 2 2005 Immunity Tick mark for Australia AS NZS CISPR 11 2004 FCC Part 15 Subpart B Class A 1 3 Base Standards for EMC amp Safety Description ipti Details A Electrostatic discharge IEC 61000 4 2 2008 Radiated radio frequency IEC 61000
4. 4 3 2006 A1 2007 electromagnetic fields A2 2010 Electrical fast transient burst IEC 61000 4 4 2004 A1 2010 IEC 61000 4 5 2005 by radio frequency fields and voltage variations Emission from Electromagnetic fields A2 2009 Voltage Fluctuation and Flicks IEC61000 3 3 2008 Requirements for Safety EN61010 1 2001 1 4 Protective class Standard enclosures IP 65 Front IP20 housing and terminals Stainless steel front Option IP 66K Front IP20 housing and terminals 1 5 Transport amp Storage conditions The following specifications apply Description Details 3 3 Drop with packing conforming to 10 drops from 60cm on 1 corner IEC 60068 2 31 3 edges 6 surfaces Drop with out packing Temperature 20 C to 60 C Relative Humidity 10 to 90 no condensation Altitude 2000 meters maximum Sinusoidal vibration conforming to 5 to 10 Hz 3 5 mm amplitude IEC 60068 2 6 10 to 150 Hz 2g 1oct min 40 SWeeps 29 Best conditions for storage of LCD display modules 1 Room ambient temperature 15 to 35 C and 6596 RH or less 2 Do not store in surroundings containing organic solvent or corrosive gas 3 Store HMI in anti electrostatic container or bag 1 6 Operating conditions Description 11 Temperature Relative Humidity Altitude Pollution Degree 2 Sinusoidal vibration conforming to 10 to 58Hz 0 75 amplitude
5. IEC 60068 2 6 58 to 150Hz 1g 1oct min 1 sweep Shock conforming to IEC 60068 2 3 shocks per direction 11ms 10g 29 In the case of temperatures below 0 C the response time of liquid crystal becomes slower and color of the display will be darker than normal Do not operate HMI in ambient temperature less than 0 1 7 LCD specifications Description si Details O Z 1 o 1 000 000 times using R 0 8 Polyacetal stylus with force 250g Vibration test 10 55 Hz Stroke 1 5mm Sweep 10 55 10Hz 2 hrs for each direction of X Y Z 3 times for each direction Package vibration test 0 015G G Hz from 5 200 Hz 6bB Octave from 200 500 Hz 2 hrs for each direction of X Y Z 10 drops from 60 cm on 1 corner 3 edges 6 surfaces Typical View Angle HMI 4 3 HMI 7 HMI 7 HIGH HMI 10 HMI 15 LOW PERFORMANCE COST Up Down Horizontal 70 70 70 7 70 70 770 75 175 85 185 Left Right 1 8 Package check list Description sf Details 1 HMI device Power supply Connector p Mounting kit CD with BSP and User manual 2 Products Overview Five HMI models HMI 4 3 HMI 7 Low Cost HMI 7 High Performance HMI 10 amp HMI 15 are available 2 1 1 Technical Specifications PERFORMANCE 480 x 272 800 x 480 800 x 480 1024 x 768 1024 x 768 W X H in pixels Display type Wide TFT Wide touch touch touch tou
6. User Manual HMI Hardware Brain Child UMHWOIA Rev 3 2012 GRAPHIC SYMBOLS INFORMATION it helps users with more details about the topic and failure to follow may lead to unpredictable results WARNING Failure to follow may lead to minor injury or damage malfunctioning of equipment LN DANGER Failure to follow may lead to injury or fatal accident to operating personal or damage malfunctioning of equipment 9 CAUTION Failure to follow may lead to malfunctioning of equipment damage or repair 3 Protective Earth n DC Supply PREFACE Original equipment manufacturer reserves the right to change information available in this document without notice Original Equipment manufacturer is not liable for any damages incurred to equipment personal during installation or use of equipment as explained in this document User must acquire sufficient knowledge amp skills prior to use the equipment in the application and follow all the local standards amp regulations to meet safety requirements WinCE is registered trade mark of Microsoft Corporation TABLE OF CONTENTS EP CI Ios m 4 Teal INSTRUCTIONS Cn 4 1 2 STANDARDS CERTIFICATES AND APPROVALS csse eene nennen 6 1 9 BASE STANDARDS FOR EMC amp SAFETY enl se A Usa ERE QOIS IEEE 6 PROTECTIVE CLASS H 6 1 9 TRANSPORT amp STORAGE CONDITIONS prania nii ian
7. a X Input amp 0 Transmit data Output 5 SG Signal Ground X amp 6 DSR j Datasetready Input 8 CTS jOleartosend 24 gt 9 RI Ring Indicator 4 5 2 COM2 port DB25 Female RS232C RS422 RS485 Fig DB25 female Signal Name Signal Type Direction FG Transmit data Output RS232C RD Receivedata Input 5232 CTS DSR __ FG D RTS Request to Output 5232 G CTS Clear to send RS232C DSR Data set ready RS232C S SG SignalGround 5V RS232C0 detect ld LL ERE LEN LL Transmit data Output RS422 RS485 Request to Output RS422 send 5 7 1 1 1 1 send Eo ld LL l1 Lo ready mmm pep supply RI Ring Indicator Input RS232C C 24 RXDA Receive data RS422 O N 2 3 4 5 8 9 0 1 2 __18__ __22__ 24 1 1 2 2 2 25 RXDB RS422 4 5 3 COM3 Reserved 4 5 4 Ethernet Pin Description NE Transmit TX Transmit TX Receive RX No connection 1 8 No connection Ethernet 10 100 Mbps No connection For HMI 10 and HMI 15 two Ethernet ports are supported Fig RJ45 connector 4 5 5 USB Host 8V00 max 100 mA 2 UON LN er Fig USB connector 4 5 6 SD slot Use only SD card r
8. before any other connection is made Do not open HMI enclosure in potentially explosive environments If any service is required switch off the power supply and bring HMI to environment which is clean Use proper tools to open HMI enclosure Repairs servicing should be done by personal qualified trained experienced and authorized to perform these kind of tasks Dangerous high voltages may be present in parts of PCB and improper servicing may cause shock and fatal injury to personal involved in job 23 All local electrical regulations should be strictly followed while connecting power supply to HMI Use proper rated cables earth grounding shielding from reliable sources line protections in power supply circuit via fuses etc to avoid shock injury death to operating personal It is advised to use uninterrupted regulated power supply with adequate protections and filters in power supply line to be used with HMI 7 The plug in terminal block for connecting the power supply is supplied along with HMI and is designed for cables with a maximum cross section of 1 5 mm 4 5 Interfaces Tighten all the screws after inserting connector at COM1 COM2 otherwise communication failure with connected PLC Inverter devices may occur because of loose connections 4 5 1 COM 1 port DB9 male RS232C 1 3 9 Fig 9 male Signal Name Signal Direction Data carrier detect Output 2 RD jReceveda
9. c metal metal Stainless Steel front N A Option Option Option bezel Option IP66K IP66K IP66K Panel Panel Panel Panel Panel Installation Mount Mount Mount Mount Mount 5 1 3 Ordering Code 3 1 HMI ordering code HMI 4 3 HMI 7 Low Cost HMI 7 High Performance HMI 10 HMI 15 O OOH O Oke HHA A HOL O OLL O OOL Enclosure 1 11 to 36V DC 0 Standard 2 90 to 250 V AC 1 Stainless Steel Sound Input Output DI 3DO None 1 Yes SD card slot None 1 Yes Ethernet None 1 Yes Other Networks None Software None opecify WinCE Core or WinCE Professional version as special note at Software 3 2 HMI Spares part list 3 2 1 HMI 4 3 L 3 2 2 HMI 7 Low Cost Part Number Part number Power Fuse 4 Amp DC power 10350 15402 01 00 10343 1103A 00 00 3 2 3 HMI 7 High Performance Part Number Part number L LCD Display Module 323 0751 3 2 4 HMI 10 ManBoard 108 Display Board HDP105 Connection Board HCB105 Sound Board HSB105 90 250VAC power board HPM751 L 3 2 5 HMI 15 Main Board 155 Backlight Board HBL155 Sound Board HSB105 90 250VAC power board HPM751 1 36VDC power board HPM754 LCD Display Module 325MODU LM1551 A0 11 It is possible to change power supply from AC to DC and vice versa Except HMI 4
10. ch TFT Wide touch Screen screen Screen Screen Screen Colors 165 536 65 536 65 536 65 536 65 536 analog analog Resistive analog analog analog Active display area 95 X 54 152 X 91 152 X 91 203 X 152 304 X 228 W X H mm MTBF back light at 25 C 30 000 hrs 0 000 hrs MainHardware 533Mhz 533Mhz ARM Cortex A8 Cortex A8 Cortex A8 667Mhz 667Mhz 667Mhz pommes o o ports Interfaces RS485 DB25 Female 1 1 1 1 1 RJ45 po General specifications ___ 24VDC 24 24V DC 24 V DC 110 220V 110 220V 110 220 110 220V Rated Voltage 24 V DC AC AC AC AC 11 36V DC 11 36V 11 36 DC 11 36V 90 250V 90 250V 11 36V DC 90 Power supply AC AC 90 250V AC 250 AC aioe Rated Current 0 91A DC 0 27A 0 29 0 6A AC Power Consumption 2W with out sound output 10 W 1 13W 2 W Power on LED indicator es Yes 15W Outer dimensions 140 X 116 X 212 X 156 212 X 156 325 X 263 X 400 X 310 W XH X D mm 57 X 57 X 57 56 X 56 51 Mounting depth mm 51 51 5 50 50 197 X 1971 X 310 X 367 X Panel cut W XH 1237 X 99 141 141 248 289 IP65 front IP65 front 1 65 front 1 65 front IP65 front Protection IP20 rear IP20 rear IP20 rear P20 rear IP20 rear Front bezel housing plastic plastic plasti
11. e HMI 7 18 4 2 3 Dimensional drawings of the HMI 10 19 4 2 4 Dimensional drawings of the HMI 159 20 SIMO re ena tein we eg trm 21 4A POWER SUPPLY 22 INTERFACE G scx mE 24 4 5 1 COM1 DBO male RS232 CC oa bo Ines otn dece e ose esu ires e cus 24 4 5 2 2 port DB25 Female 52326 65422 5485 25 Z 5 9 COMS Reserved d aM us guste aud 26 4 5 4 lle Eh 26 USB AOS a 26 4 5 6 eee er ce he Marc E IM uU MI ca e 26 4 5 7 Sound INDUY OUI 27 4 5 8 PRES CIN m orn 27 te REALTIME GEOGR see ew 27 PROCEDURES mi io nie a locatus D ioi euh 27 1 1 1 Instructions Read Installation and Operation manuals carefully before installation repairs or commissioning of the equipment Follow all local standards regulations for using electrical power supply connection to the equipment grounding shielding during installation and commissioning Obtain sufficient skills and training before using the equipment lf any damages are observed in transportation inform to the supplier with supporting information including product details and photographs
12. e to operators When HMI is installed inside main panel make sure that proper vents are available for the main panel ambient temperature inside the panel is not exceeded beyond HMI specifications operator is alerted incase of exceeding temperature limits When HMI is installed on panel front door check depth of the HMI and make sure that there is enough clearance available inside the panel after closing the main panel door A sufficient panel gage should be used in the main panel to firmly install HMI Take care when using stainless steel fronts as weight is heavy compared with alloy or plastic fronts Use rubber gaskets properly to achieve degree of Ingress Protection Use panel cut out as specified and firmly attach all mounting clips Maintain proper clearances around the HMI panel approx 50 mm on all directions to make sure that it is easy to remove HMI for maintenance purpose and temperature dissipates by natural air cooling method Use proper line protections in power supply line via fuses circuit breakers etc Connect earth properly to the HMI enclosures panels cabinets housings 15 Use proper cables connect to ground properly before connecting power supply to HMI 16 Thoroughly check voltage levels accepted by HMI measure voltage levels with a multimeter before connecting them with HMI 17 While using HMI with stainless steel front for wash down applications make sure that panels enclosures cabinets housings are perfectly cl
13. ecommended by manufacturer 26 4 5 7 Sound input Output P 4 Sound Input It is to connect Microphone Reserved to use in future K Sound Output It is to play audio files on trigger of Event Alarm Sound input output connector Use 3 5mm diameter with 14mm length stereo phone plug E m 3 5 MATE PLUG 4 5 8 Reserved 4 6 Real Time Clock Make Seiko Instruments Model MS621 FL11E Rating V 4 mAH ypical life time 10 yrs uffer period 6 months ype Rechargeable Accuracy Maximum 2 sec day 4 7 HMI Reset Procedure Short Pin no 2 and Pin no 3 at COM2 in HMI Then Power ON the HMI 2 Press Yes Remove short link across Pin2 and Pin3 at COM2 and then press Now complete the calibration of touch screen at HMI This reset procedure will clear all the contents in Resident flash and load default factory settings into Flash memory 28
14. n lise ieee 109 OPERATING ONDIMION Tof SPECIFICATIONS su oeste basata alo 8 1 89 PACKAGE CHECK dicrum 8 2 PRODUCTS OVERVIEW 9 2 1 1 Technical Specili c allolS conum mists Qnid c xu de ai Pract Chatten ce Ut 9 o ORDERING CODE 59d dust dusk coax pales eh oci Pria 11 SUL AM ORDERING hdl cd iud ends toties bees cas dd tun but entes dat 11 D AMI SPARES PART LIS E ED IL UE 12 3 2 1 wl ENS e geet 12 9 2 2 AME LOW COSI 12 3 2 3 HMI 7 High Performance cccccscccseseecseseecseseeceueceneueceseseeeeaeeesesesenseeesnees 12 3 2 4 PIU uU EU ui Ene i 13 3 2 5 mul ce a 13 0 97 RESERVED run nM bau ioo Ania 14 9 4 ACCESSORIES PART NUMBERS 2 55 Meike 14 Ae INSTALLA HON mc 15 qd INSTALLATION ec t b Fees LI RII 15 4 2 DIMENSIONAL DRAWINGS 17 4 2 1 Dimensional drawings of the HMI 4 3 17 4 2 2 Dimensional drawings of th
15. osed to avoid water entry inside panels causing damages to the equipment and injury to operating personal 18 Improper installation voids warranty 4 2 Dimensional drawings 4 2 1 Dimensional drawings of the HMI 4 3 122 0 00 9 6 0 1450 Note All dimensions are in mm Tolerance 1 mm Panel cutout 123 X 99 uli 1 9 Male Network option LAN Ethernet RJ45 IH SD slot DB25 Female USB port Power supply 4 2 2 Dimensional drawings of the HMI 7 HMI 750 Note All dimensions are in mm Tolerance 1 mm Panel cutout 197 X 1417 DB9 Male LAN Ethernet RJ45 SD slot DB25 Female USB port Om Power supply Network option 4 2 3 Dimensional drawings of the HMI 10 247 0 145 5 HMI 1050 Note All dimensions are in mm Tolerance 1 Panel cutout 310 X 248 E DB9 Male Network option LAN1 Ethernet RJ45 SD slot 4 2 4 Dimensional drawings of the HMI 15 SD LAN2 LANI USB HMI 1550 Note All dimensions are in mm Tolerance 1 mm Panel cutout 367 X 289 DB9 Male LAN1 Ethernet RJ45 SD slot ii COM 25 Female LAN2 Ethernet Ru45 12 8 Power supply Network option USB port 20 4 3 Mounting It is possible to insert HMI in either vertical or horizontal direction in enclosures panels cabinets housings Panel cut out is as follows If HMI to be in
16. stalled vertically while creating new project in HMI editor software select resolution carefully at the beginning and then select the angle correctly during HMI start up at the panel Please refer section Instrument at HMI startup about how to select angle for vertical installation Horizontal Installation HMI 7 HMI 7 HIGH LOW PERFORMANCE COST Width mm Height mm Depth mm Vertical Installation HMI 7 HMI 7 HIGH LOW PERFORMANCE COST HMI 4 3 4 nos mounting clips HMI 7 LOW COST HMI 7 HIGH PERFORMANCE 6 nos mounting clips HMI 10 10 nos Mounting clips HMI 15 12 nos Mounting clips 21 Mounting clips for HMI with Metal enclosures Top view Bottom View Use Proper Tools to open HMI enclosure Mounting clips for HMI with Plastic enclosures Top view Bottom View 7 Tighten all mounting clips otherwise it may effect the touch panel operation and ingress protection will be compromised 4 4 Power Supply The following options are available 1 AC Power 90 250 V AC 47 63 Hz Universal AC power supply Except HMI 4 3 2 DC Power 11 36 V DC 22 AC Power 90 250 V AC 47 63Hz tm m DC Power 11 36 V DC Description 11 36VDC Different power boards are available for above options and they will be fitted into HMI as per ordering code 5 The protective earth terminal should be connected first
Download Pdf Manuals
Related Search