CFO100 user manual
Contents
1. Note For correct optical operation ensure that all optical connectors are cleaned immediately before mating Connectors should always be cleaned using high purity alcohol e g methyl or isopropyl alcohol Dry the surfaces using clean compressed air or other equivalent pressurised gas The female ST optical connectors on the equipment should always be protected with dustcaps when there is no fibre inserted Optical connection meets class 1M laser safety requirements of IEC 60825 1 2001 and US department of health services 21 CFR 1040 10 and 1040 11 1990 when operated within the specified temperature power supply and duty cycle ranges CFO100 user manual CPT101 stand alone installation The CPT101 units are designed for stand alone installation The unit should be mounted with a help of wall bracket to a installation place The supply voltage can be either 12V DC or 24V AC The supply voltage is provided by either a surveillance camera unit or by an external mains adapter The permitted supply voltage range are 10 5 14 VDC and 16 24 VAC In DC use the 12V DC supply voltage is supplied by the means of a separate mains adapter with a regulated output e g CPS251 The permitted operational temperature range is 34 74 C Wall bracket dimensions CFO100 user manual 3 CRT103 triple channel video transmitter CAUTION THESE OPTICAL UNITS USES CLASS 1M LASER DIODE DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICA2. the module adapter push the unit along the guide rails into module until the unit is firmly attached Secure the plug in unit with the upper and lower locking screws The stand alone unit should be mounted to a vertical surface The permitted supply voltage range is 10 5 14 VDC The current consumption is 300 mA The permitted operational temperature range is 34 74 C Note Alternatively the units can be installed for stand alone use by using a CMA025 installation for two 5HP wide units or CMA035 installation for three 5HP wide units module adapters The 12V DC supply voltage is supplied by the means of a separate mains adapter with a regulated output e g CPS251 Please refer to separate documention for module adapters and mains adapters For limited space installation the CMA015 025 035 module adapters can be rear mounted by means of an optional installation kit CIKO02 CPS251 12VDC mains adapter CMA CPS DC connection polarity CMA025 module adapter with CIK002 rear mounting kit 1 CMA025 module adapter 2 CIKOO2 rear mounting kit CFO100 user manual 5 top view a E Fibre connection The optical connector is of the type ST The optical output level is typically 4 dBm For testing purposes the CFO100 series transmitter and receicer can be connected with a short fibre patch cable The operating wavelenght is 1310 nm Lo i When ins
3. 130 mA and for CRR103 300 mA The permitted operational temperature range is 34 74 C Note Alternatively the units can be installed for stand alone use by using a CMA025 installation for two 5HP wide units or CMA035 installation for three 5HP wide units module adapters The 12V DC supply voltage is supplied by the means of a separate mains adapter with a regulated output e g CPS251 Please refer to separate documention for module adapters and mains adapters For limited space installation the CMA015 025 035 module adapters can be rear mounted by means of an optional installation kit CIKO02 CPS251 12VDC mains adapter CMA CPS DC connection polarity CMA025 module adapter with CIK002 rear mounting kit 1 CMA025 module adapter 2 CIKOO2 rear mounting kit 8 CFO100 user manual top view E A Fibre connection The optical connector is of the type ST Minimum optical intput level is typically 25 dBm No adjustments for input are needed The operating wavelenght is 1310 nm When installing the fibre optic cable do not exceed the minimum bending radius when connecting cable to the system iy il Note For correct optical operation ensure that all optical connectors are cleaned immediately before mating Connectors should always be cleaned using high purity alcohol e g methyl or isopropyl alcohol Dry the surfaces using clean compressed a
4. L INSTRUMENTS APPLICABLE STANDARD 1EC60825 1 2001 The CRT103 is a three channel optical transmitter for uni directional video transmission in a multimode fibre The current consumption is 300 mA 12 VDC Frame installation The CRT103 module is to be pushed along the guide rails into the installation frame e g CSR216 or 316 series and secured with the two locking screws The unit can be freely positioned in any slot in the frame The empty positions in the frame should be blanked off with cover plates The supply voltage is to be provided by a CPS384 or CPS390 power supply unit which are installed back of frame Video connections The impedance of the video inputs BNC female is 75 O The nominal input level is 1 Vpp Link status indicator LEDs In the uni directional CRT103 units the LINK STATUS led is only monitored by the optical receiver CRR101 103 Therefore the LINK STATUS led in CRT103 units has no real value and is always green CRT103 5 OPTICAL TRANSMITTER omm CRT103 Optical Transmitter 1 Locking screw 2 pcs 2 Video input BNC female 3 Optical output ST 4 Link status indicator led 5 Handle with unit information See further information on dedicated sections 4 CFO100 user manual CRT103 stand alone installation The units can be installed for stand alone use by using a CMA015 installation for one SHP wide units module adapters To insert a CRT103 card unit into
5. TELESTE User manual Single and triple channel video only link CFO First Mile series consist of fibre optic modems which provide a high quality and lossless video transmission for variety of CCTV applications CRR103 OPTICAL RECEIVER Video Security and Information CFO100 user manual 59300292 rev003 Contents CFO100 Single and triple channel video only link oooccccocccnccoccnccoccnnononononononononcncnnarnnononcnnnancnnnnnns 1 Ente po EPR OPC III o en A 1 A AI 1 CPT101 mini sized stand alone video transmitter 0 cece cc eec eee eceeceeeeceeneeeeneeeeceeaeseeaeseaeseeeseeeneeeeeaeeeees 2 SA A e ee A 2 VGSO nn PP o A E A E 2 Fire connection eee eee er ne ea ne alain tia een a 2 CP TA01 Stan alO ie WAS all AU OMA iaa ota il naaa 3 CRT103 triple channel video transmitter ooccoocccocncoonccncncocnconcconnncncnnonnconnnonnnnornnonnnonnnnnnnnonnconrnnnnncnnncnnnos 4 SA A quen e E E II caeeesaraies endecs 4 ca 6 L116 9 ee ee a ne een ne ee en eee 4 vdeo CO Mie COINS AAPP o A 4 Link status indicator LEDS usina di dla 4 CRI103siand alone Instala sica sirio debate coa EAA AREENA AE ATANAN TENAAAN 5 Fibre CONNECUON escurrir er ee E 6 CRR101 103 single and triple channel video receiver ooocccccocccccccccnconccncononononncnnonnnnnononcnonnnrnnonancnnnnncnnnnas 7 A SSA 7 Fe Slits O e PET EE A A 7 Video connections and indicator LEDS o occoco
6. cococcncnconcncncnnnnoncncnnc cnn nono non nono nr n rn nena n rn rre ARPAD rn nn nr nen nnenenannnnnnanes 7 MIS Stats INICIO LEDS aos cane 7 CRR101 103 stand alone installation cece eceeceeceeeeceeeeceeeeeeeneeeeneeneceeaeeaeaeeeeneeaeseeaeeeeaeseaeeneneneeaeeeeneeenaess 8 FUNG COMME CU OM onae M E E O E o II Ei 9 PSS AUC CAN AION secera ennen eein anea Ea a EEEa EAE EE ude EEEIEE EEE EEA TEENE AURREK 10 WEEE o E E E PP O a ee E 10 Video Video gt Video gt Video gt Video gt CPT101 CPT101 Video CRR101 CRR103 multimode fibres up to 6 5 km Video Video Video multimode fibres up to 6 5 km Video Video CRT103 CRR103 gt video Video gt Video multimode fibres up to 6 5 km CFO100 user manual CF0O100 Single and triple channel video only link CFO100 First Miles series offers a 10 bit video transmission over one mutimode fibe video channel for fixed camera applications V V V V Welcome and thank you for purchasing Teleste s CFO products gt S gt EXI gt gt gt CFO100 First Mile series offers a highly cost effective single channel composite video transmission over one multimode fibre High quality video image can be transmitted over distances up to 6 5 km depending on the type of multimode fibre in use A typical application is a point to point transmission from a fixed CCTV camera to a monitoring cent
7. ir or other equivalent pressurised gas The female ST optical connectors on the equipment should always be protected with dustcaps when there is no fibre inserted Optical connection meets class 1M laser safety requirements of IEC 60825 1 2001 and US department of health services 21 CFR 1040 10 and 1040 11 1990 when operated within the specified temperature power supply and duty cycle ranges ST Connectors Make sure the key is aligned in the slot properly before tightening CFO100 user manual 9 10 Legal declarations Copyright 2015 Teleste Corporation All rights reserved TELESTE is a registered trademark of Teleste Corporation Other product and service marks are property of their respective owners This document is protected by copyright laws Unauthorized distribution or reproduction of this document is strictly prohibited Teleste reserves the right to make changes to any of the products described in this document without notice and all specifications are subject to change without notice Current product specifications are stated in the latest versions of detailed product specifications To the maximum extent permitted by applicable law under no circumstances shall Teleste be responsible for any loss of data or income or any special incidental consequential or indirect damages howsoever caused The contents of this document are provided as is Except as required by applicable law no warranties of any ki
8. n the frame The empty positions in the frame should be blanked off with cover plates The supply voltage is to be provided by a CPS384 or CPS390 power supply unit which are installed back of frame Video connections and indicator LEDs The impedance of the video outputs BNC female is 75 O The nominal output level is 1 Vpp Link status indicator LEDs When the optical input signal level is adequate and syncronization on link level is achieved the LINK STATUS led on the front panel is green If optical input signal is missing or it s level is too low the LINK STATUS led is yellow CRR103 5 OPTICAL RECEIVER OE CRR103 Optical Receiver 1 Locking screw 2 pcs 2 Video output BNC female 3 Optical input ST 4 Link status indicator led 5 Handle with unit information See further information on dedicated sections Note CRR101 is a single channel version of CRR103 CFO100 user manual T CRR101 103 stand alone installation The units can be installed for stand alone use by using a CMA015 installation for one SHP wide units module adapters To insert a CRR101 103 card unit into the module adapter push the unit along the guide rails into module until the unit is firmly attached Secure the plug in unit with the upper and lower locking screws The stand alone unit should be mounted to a vertical surface The permitted supply voltage range is 10 5 14 VDC The current consumption for CRR101 is
9. nd either express or implied including but not limited to the implied warranties of merchantability and fitness for a particular purpose are made in relation to the accuracy reliability or contents of this document Teleste reserves the right to revise this document or withdraw it at any time without notice WEEE directive Directive 2002 96 EC of the European Parliament and of the Council on waste electrical and electronic equipment WEEE obliges that producers appropriately mark electrical and electronic equipment with the symbol indicating separate collection This obligation applies to the equipment put on the market in EU after 13 August 2005 Teleste devices which belong to the scope of the directive have been marked with the separate collection symbol shown below The marking is according to the standard EN 50419 The symbol indicates that the device has to be collected and treated separately from unsorted municipal waste User manual revision history note The latest version is always available in pdf format on our web site www teleste com CFO100 user manual
10. nsmitter and receiver gt gt Transmitter unit available in a special compact size stand alone design gt gt Feasible for field hardened operation gt gt Mechanically compact and ruggedised gt gt EMC and environmental conformance CFO100 user manual 1 CPT101 mini sized stand alone video transmitter CAUTION THESE OPTICAL UNITS USES CLASS 1M LASER DIODE DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS APPLICABLE STANDARD 1EC60825 1 2001 side view CPT101 Digi Pixi CPT101 Optical Transmitter 1 Video input BNC female 2 Optical output ST 3 Power led 4 Power supply connector 2 pin screw terminal 5 Grounding top view EF ji ST Connectors Make sure the key is aligned in the slot properly before tightening The CPT101 is a one channel optical transmitter for uni directional video transmission in a multimode fibre The current consumption is max 130 mA 12V DC Video input The video input impedance BNC female is 75 Q The nominal input level is 1 Vpp Fibre connection The optical connector is of the type ST The optical output level is typically 4 dBm For testing purposes the CFO100 series transmitter and receicer can be connected with a short fibre patch cable The operating wavelenght is 1310 nm When installing the fibre optic cable do not exceed the minimum bending radius when connecting cable to the system
11. re CFO100 series consist of mini sized stand alone video transmitter followed by standard 5HP size CFO cards for triple channel video transmitter as well as for single and triple channel receiver operation The CPT101 stand alone transmitter is temperature hardened and is capable of using both 12 VDC or 24 VAC supply voltage CPT101 unit is a compact size housing for special stand alone installations requiring minimal installation space Also as an optional DIN rail mounting is possible item code CIK001 CRT103 and CRR101 103 cards are compatible with all CFO rack systems Stand alone options are available with the CMA015 module adapter and separared CPS25x series mains adapter As with all CFO platform products these specific models do meet all typical EMC as well as other environmental and manufacturing related requirements The permitted operational temperature range is 34 74 C Note New generation CFO100 products are based on digital transmission and are not therefore compatible with previous analog CFO100 series gt gt Low cost video transmission gt gt High performance uncompressed Zero delay digital video transmission SNR 65 dB typical 10 bit video sampling gt gt One CVBS PAL NTSC video channel gt gt Transmission over on one or three multimode fibre up to 6 5 km gt gt Card format applicable both for rack mount and stand alone installations gt gt One and triple channel units available for both tra
12. talling the fibre optic cable do not exceed the minimum bending radius when connecting cable to the system Note For correct optical operation ensure that all optical connectors are cleaned immediately before mating Connectors should always be cleaned using high purity alcohol e g methyl or isopropyl alcohol Dry the surfaces using clean compressed air or other equivalent pressurised gas The female ST optical connectors on the equipment should always be protected with dustcaps when there is no fibre inserted Optical connection meets class 1M laser safety requirements of IEC 60825 1 2001 and US department of health services 21 CFR 1040 10 and 1040 11 1990 when operated within the specified temperature power supply and duty cycle ranges ST Connectors Make sure the key is aligned in the slot properly before tightening CFO100 user manual CRR101 103 single and triple channel video receiver The CRR101 is a one channel optical receiver for uni directional video transmission in a multimode fibre The current consumption is 130 mA 12 VDC The CRR103 is a three channel optical receiver for uni directional video transmission in a multimode fibre The current consumption is 300 mA 12 VDC Frame installation The CRR101 103 module is to be pushed along the guide rails into the installation frame e g CSR216 or 316 series and secured with the two locking screws The unit can be freely positioned in any slot i
Download Pdf Manuals
Related Search