STS-20A -100A
Contents
1. Red input 1 fault Green output using input 1 Output normal Red Output fault choose working mode Under auto mode input 1 will be named as priority automatically 3 2 2 Rear panel 1 2 34567 8 9 1011 N Description venim Input 2 fault 4 Connector Input 1 N AN 2yzbems TST100 user s manual 5 Connector Earth 6 Connector _ Input2 L Input 2 N 8 Circuit breaker Input 2 circuit breaker 9 Connector jOutpt L 10 Connector Output N I 2 Communication port RS485 3 3 Structure Size 402 5 el wo m a 4 10 346 6 AN 2yzbems TST100 user s manual 4 Installation 4 1 Preparation Only a professional electrician is permitted to install the unit 4 1 1 Inspection Before installation unit should be unpack the package and check the package contents Keep all spare part and accessories for future use 4 1 2 Tool Information Multi meter tool box user manual cable 4 1 3 Ambient Condition Environment requirements Working temperature 0 40 C Storage temperature 40 70 C Relative Humidity 096 9596 non condensing Cooling forced air Vertical angle No vibration and hading angle less than 5 degree Working temperature of 20 25 C and Humidity of 50 are recommended Caution The STS must be installed in a location with good ventilation far away from water inflammable gas and corrosive agent TST100 us2. TST100 Static Transfer Switch USER MANUAL Version 1 0 Date Nov 2009 AN Systems TST100 user s manual 1 Important Safety Instruction WARNING Please read safety guide below before using inverter powersupply 1 1 Safety Instruction As dangerous voltages and high temperature exist within the equipment only qualified and authorized maintenance personnel are permitted to open and repair it This manual contains information concerning the installation and operation of the TST100 All relevant parts of the manual should be read prior to commencing the installation Please follow the local stipulation meantime Any operation against safety requirement or against design manufacture safety standard and are out of the manufacturer warranty 1 2 General Precaution 1 2 1 Do not expose to dust rain snow or liquids of any type it is designed for indoor use DO NOT block off ventilation otherwise it would be overheating 1 2 2 To avoid fire and electric shock make sure all cables selected with right gauge and being connected well Smaller diameter and broken cable are not allowed to use TST100 user s manual 2 Introduction 2 1 Introduction The TST100 Static Transfer Switch is single phase transfer device providing automatic switching between two independent AC power sources It combined the STS and MTS into one unit which greatly increased the system reliability along reducing the transfe
3. er s manual 5 0 Operation 5 1 Power ON Double confirm the input voltage matches the voltage of this equipment do not connect different voltage otherwise it will damage the equipment Check if wiring of input 1 input 2 and output are right After above check and everything is right please switch on the input 1 switch and input 2 switch 5 2 Operation 5 2 1 Switch Test Set the auto manual switch at manual you can choose either input as main e Set the auto manual switch at auto the input 1 will be chose as main Switch off the input 1 and STS will switch to input 2 Then close the input 1 switch the STS will resume to input 1 e At auto position you can not manually choose input 1 or input 2 5 2 2 Mute System offer alarm in case of fault you could press mute button for 3secs in case of alarm Sysioms Unit 3 30 Heathcote Rd Moorebank NSW 2170 Ph 02 9602 8331 www alphapower com au
4. r time to less than 4ms It was suitable for important IT equipment which can not afford power disruption and ATS can not satisfy 2 2 Feature Transfer time less than 4ms when input power are synchronization and transfer time is less than 10ms in case of input non synchronization Intelligent monitor diagnostics and alarming Protection and alarm against High Voltage Low Voltage Power Failure and Overload Overload protection STS shutdown in case of 150 overload and will reconnect after 10s Shortcut protection in case of output shortcut system would cutout output offering protection for input power User can set up either input as main and the other will be standby automatically Support manual select In case of STS fail the system will choose one input source as fix source to ensure uninterruptible power supply e RS232 or RS485 communication otructure 19 2U A 2 3 Specification TST100 user s manual Model TST120 Dimension 19 2U 87x483x259mm HxWxD Input voltage 220 15 Input rated frequency 50Hz 60Hz transfer time Operation Temp 5C 40C Communication RS485 Dry contacts TST100 user s manual 3 Principle and structure 3 1 Principle 3 2 Panel and Indicators 3 2 1 Front panel re no MANUAL SYNC e INPUT II SILENT TST100 user s manual LED indicate input 1 and input 2 are in synchronization 2 our Green input 1 normal
Download Pdf Manuals
Related Search