User Manual
Contents
1. Copyright 2009 2011 GigaLink Page 14 of 29 GL GIGALINK GL VP 62x0 User Manual Do not interrupt the firmware upgrading process NTP Server time gist gov URI or IP address Lock Keypad Update No OYes configuration update via keypad is disabled if setto Yes Disable Voice Prompt No Yes voice promptis disabled if setto Yes Syslog Send Syslog Level NONE v i Download Device Configuration SUPER CONFIGURATION PAGE DEFINITIONS Setting Options Meaning This parameter defines the URI or IP address of the NTP NTP Server server which is used by the GL VP 62x0 to display the current date time If this parameter is set to Yes the configuration update via keypad is disabled Disable Voice Prompt Default is No Syslog Server The IP address or URL of System log server This feature is especially useful for the ITSP Internet Telephone Service Provider Syslog Level Select the GL VP 62x0 to report the log level Default is NONE The level is one of DEBUG INFO WARNING or ERROR Syslog messages are sent based on the following events Lock Keypad Update product model version on boot up INFO level NAT related info INFO level sent or received SIP message DEBUG level SIP message summary INFO level inbound and outbound calls INFO level registration status change INFO level negotiated codec INFO level Ethernet link up INFO level 9 SLIC chip exception2. Refer To Use Target Contact Default is No If set to Yes then for Attended Transfer the Refer To header uses the transferred target s Contact header information DTMF Payload Type Sets the payload type for DTMF using RFC2833 DTMF in Audio Send DTMF as inband in audio DTMF via RFC2833 DTMF via SIP INFO Send Flash Event Proxy Require Use NAT IP Preferred Vocoder in listed order Voice Frames per TX G723 rate iLBC frame size iLBC payload type G726 16 Payload Type G7 26 24 Payload Type G726 40 Payload Type Setting Options ONo ONo choice 1 choice 2 choice 3 choice 4 choice 5 choice 6 E 6 3kbps encoding rate 20ms oF 100 ER 103 Yes Ces Yes Flash will be sent as a DTMF event if set to Yes used in SIP SDP message if specified current setting is PEMU ze current setting is s 6 72632 v current setting is G 723 1 current setting is PCMA v current setting is G 726 Y current setting is G 729A B v up to 10 20 32 64 for G711 G726 G723 other codecs respectively 3kbps encoding rate 30ms between 96 and 127 defaultis 97 es 96 and 127 defaultis 100 between 96 and 127 defaultis 99 between 96 and 127 defaultis 103 PROFILE PAGE DEFINITIONS DTMF via RFC2833 Meaning Default YES DTMF via SIP INFO Send DTMF via SIP INFO message Send Flash Event Default is No If
3. 014 please type in 192 168 1 14 5 2 End User Configuration Once the HTTP request is entered and sent from a Web browser the user will see a log in screen There are two default passwords for the login page User Password Level End User Level 1234 Only Status and Basic Settings Administrator Level admin Browse all pages After login the next configuration page is the Basic Configuration page explained in detail in Table 5 Web Log in Definition TABLE 5 Web Log In Definitions Basic Settings Page Copyright 2009 2011 GigaLink Page 9 of 29 GL GIGALINK GL VP 62x0 User Manual W Web Port 80 default for HTTP is 80 dynamically assigned via DHCP DHCP hostname optional DHCP domain optional DHCP vendor class ID optional O use PPPoE PPPoE account ID PPPoE password IP Address PPPoE Service Name Preferred DNS server 0 J0 10 0 statically configured as IP Address 192 168 Su 115 Subnet Mask 255 1255 11255 DU Default Router 192 1 168 L 0 I 1 DNS Server 1 218 GR 11135 1 DNS Server 2 192 168 0 1 Cloned WAN MAC Addr oo iif cl 11 23 15 In hex format Time Zone GMT 8 00 Beijing Singapore Taipei Kuala Lumpur Irkutsk Perth Ni WEB LOG IN DEFINITIONS BASIC SETTINGS PAGE Setting Options Web Port Meaning By default HTTP uses port 80 This field is for customizable web port IP Address There are two modes to operate the GL VP 62x0 DHCP mode all the field values
4. 180 Min SE 30 GL VP 62x0 User Manual between 96 and 127 defaultis 102 Yes Ces Auto Detect Pass Through O caller Callee Fixed Adaptive O Medium High in seconds defaultis 4 seconds Yes use Yes only if proxy supports 484 response this prefix string is added to each dialed number Yes if setto Yes r will function as the Re Dial key No do not send SUBSCRIBE for Message Waiting Indication send periodical SUBSCRIBE for Message Waiting Indication Ces caller ID will be blocked if setto Yes Ces in seconds default 180 seconds in seconds default and minimum 90 seconds PROFILE PAGE DEFINITIONS Setting Options G729E Payload Meaning Default value is 102 Range is from 96 to 127 Type Default is No VAD allows detecting the absence of audio VAD and conserve bandwidth by preventing the transmission of silent packets over the network Default is No When set to Yes the device will change the e ic RTP destination to send RTP packets to the source IP address HE and port of the inbound RTP packet last received by the device Fax Mode T 38 Auto Detect FolP by default or Pass Through must use codec PCMU PCMA Fax Tone Detection Mode Default is Callee This decides whether Caller or Callee sends out the re INVITE for T 38 or Fax Pass Through Jitter Buffer Type Select either Fixed or Adaptive based on network conditions Jitter Bu
5. 62x0 is a next generation IP voice and video gateway that features full interoperability with leading IP PBXs SoftSwitches and SIP platforms The Gateway series offers superb voice and video quality traditional telephony functionality simple configuration feature rich functionality and an additional video port that enables the gateway to act like a video surveillance gateway 4 1 External power supply VV VV VV VV V WV T 38 compliant 4 and 8 FXO port gateways Software Features Overview Two RJ 45 ports switched or routed TFTP and HTTP firmware upgrade support Multiple SIP accounts multiple SIP profiles choice of 2 profiles per account Supports Audio Codecs G711U A G723 G729A B and GSM G 168 echo cancellation Flexible DTMF transmission In Audio RFC2833 SIP Info or any combination of the 3 Selectable multiple LBR coders per channel TABLE 3 GL VP 62x0 Software Features GL VP 62x0 FXO Analog Gateway Series IP settings GL VP xxxx 6040 4 ports 4 SIP accounts w choice of 3 SIP Server profiles GL VP xxxx 6080 8 ports 8 SIP accounts w choice of 3 SIP Server profiles Round robin port scheduling to ensure available lines to access PSTN networks Telephone Interfaces FXO RJ11 Network Interface Two 2 10M 100 Mbps Ru 45 LED Indicators Power and Line LEDs Voice over Packet Capabilities G 168 compliant Echo Cancellation Dynamic Jitter Buffer Modem detection amp auto sw
6. WARNING and ERROR levels 10 memory exception ERROR level Download Device User can download configuration from the web page and Configuration save to configuration file ON OF gt NS Copyright 2009 2011 GigaLink Page 15 of 29 GL GIGALINK GL VP 62x0 User Manual Syntax fl freqa ivol G heg vol cont offt on2 off2 on3 off3 Note freq 0 4000Hz vol 30 0dBm R Dial Tone f1 350 13 2 440 13 c 04 Ringback Tone f1 440 19 2 490 19 c 20004000 Busy Tone f1 480 24 Q 620 24 c 500 S00 paar oprone Teme Reorder Tone 11 420 24 2 620 24 c 250 250 Confirmation Tone f1 350 11 2 440 11 100 100 100 100 100 100 Call Waiting Tone 1 440 13 c 300 10000 300 10000 0 0 Default Ring 1 440 13 2 490 13 c 2000 4000 Cadence Only the cadence is configurable Syntax c ont oft on2 off2 on3 on3 f D SaveSet Reboot Restore Configuration E __ Restore Configuration Restore License wim d Restore License SUPER CONFIGURATION PAGE DEFINITIONS Setting Options Meaning Using these settings user can configure tone frequencies according to their preference By default they are set to North American frequencies Frequencies should be configured with known values to avoid uncomfortable high pitch sounds ON is the period of ringing On time in ms while OFF is the period of silence In order to set a continuous tone OFF should be zero Otherwise it will rin
7. for the Static IP mode are not used even though they are still saved in the Flash memory The GL VP 62x0 acquires its IP address from the first DHCP server it discovers from thd LAN it is connected Using the PPPoE feature set the PPPoE account settings The GL VP 62x0 will establish a PPPoE session if any of the PPPoE fields is set Static IP mode configure the IP address Subnet Mask Default Router IP address DNS Server 1 primary DNS Server 2 secondary fields Time Zone Controls how the date time is displayed according to the specified time zone Copyright 2009 2011 GigaLink Page 10 of 29 GL GIGALINK Daylight Savings Time Date Display Format Device Mode LAN Subnet Mask LAN DHCP Base IP DHCP IP Lease Time DMZ IP GL VP 62x0 User Manual No O Yes f setto Yes display time will be 1 hour ahead of normal time Year Month Day Month Day Year Day Month Year NAT Router O Bridge 255 255 255 0 Default is 255 255 255 0 192 168 2 1 Base IP for the LAN port default is 192 168 2 1 24 Hours Defaultis 120 hours or 5 days WEB LOG IN DEFINITIONS BASIC SETTINGS PAGE Setting Options Daylight Savings Time be daylight savings time or not If set to Yes then the Meaning This parameter controls whether the displayed time will displayed time will be 1 hour ahead of normal time Date Display Format Year Month Day Allow user to choose among the followin
8. set to yes flash will be sent as DTMF event Proxy Require SIP Extension to notify SIP server that the unit is behind the NAT Firewall Copyright 2009 2011 GigaLink Page 21 of 29 GL GIGALINK GL VP 62x0 User Manual Use NAT IP NAT IP address used in SIP SDP message Default is blank Preferred Vocoder in listed order The GL VP 62x0 supports up to 5 different Vocoder types including G 711 A U law G 726 Supports bit rates 16 24 32 and 40 G 723 1 G 729A B E The user can configure Vocoders in a preference list that will be included with the same preference order in SDP message The first Vocoder is entered by choosing the appropriate option in Choice 1 The last Vocoder is entered by choosing the appropriate option in Choice 8 Voice Frames per TX This field contains the number of voice frames to be transmitted in a single packet When setting this value the user should be aware of the requested packet time used in SDP message as a result of configuring this parameter This parameter is associated with the first vocoder in the above vocoder Preference List or the actual used payload type negotiated between the 2 conversation parties at run time e g if the first vocoder is configured as G723 and the Voice Frames per TX is set to be 2 then the ptime value in the SDP message of an INVITE request will be 60ms because each G723 voice frame contains 30m
9. the GL VP 62x0 NAT traversal mechanism is activated or not If activated by choosing Yes and a STUN server is also specified then the GL VP 62x0 performs according to the STUN client NAT Traversal Copyright 2009 2011 GigaLink Page 19 of 29 GL GIGALINK GL VP 62x0 User Manual specification Under this mode the embedded STUN client will detect if and what type of firewall NAT is being used If the detected NAT is a Full Cone Restricted Cone ora Port Restricted Cone the GL VP 62x0 will use its mapped public IP address and port in all of its SIP and SDP messages If the NAT Traversal field is set to Yes with no specified STUN server the GL VP 62x0 will periodically every 20 seconds or so send a blank UDP packet with no payload data to the SIP server to keep the hole on the NAT open Connect to Asterisk If you want to register to Asterisk please choose YES If not please choose NO Default is No Use DNS SRV If set to Yes the client will use DNS SRV to look up server If the GL VP 62x0 has an assigned PSTN telephone number this field should be set to Yes Otherwise set User ID is Phone it to No Number If Yes is set a user phone parameter will be attached to the From header in SIP request SIP Registration This parameter controls whether the GL VP 62x0 needs to send REGISTER messages to the proxy server The defa
10. will be disabled Send anonymous All calls forwarded to VOIP end will be sent as anonymous PIN for PSTN Calls Enter digits to authorize calling PSTN numbers from VOIP no default PIN for VOIP Calls Enter digits to authorize calling VOIP terminals from PSTN no default Unconditional Call Forward to PSTN VOIP calls will be forwarded to the specified PSTN number Unconditional Call Forward to VOIP This is an extremely important setting to make sure incoming PSTN calls are picked up and forwarded to the correct VOIP destination User ID This parameter allows users to configure a User ID or extension number to be automatically dialed upon FXO line off hook SIP Server You also need to specify the Profile ofthe user id configured above p1 stands for Profile 1 p2 stands for Profile 2 and so on SIP Destination Port Along with the user id and Profile you also have the option to choose the destination port where you would like to send the call By default it should be set to ch1 x 5060 x can be 4 or 8 depending on number of ports 5 6 Saving The Configuration Changes Once a change is made press the Update button in the Configuration Menu The GL VP 62x0 will display the following screen to confirm that the changes have been saved To activate changes reboot or power cycle the GL VP 62x0 after all changes are made FIGURE 5 Screen Shot Of Save Configuration Copyright 200
11. 011 GigaLink Page 27 of 29 GL GIGALINK GL VP 62x0 User Manual Once the TFTP server is configured please power cycle the GL VP 62x0 TFTP process may take as long as 1 to 2 minutes over the Internet or just 20 seconds if it is performed on a LAN Users are recommended to conduct TFTP upgrade ina controlled LAN environment if possible For those who do not have a local TFTP server GigaLink technology provides a NAT friendly TFTP server on the public Internet for firmware upgrade Please check the Service section of GigaLink s Web site to obtain this TFTP server s IP address NOTES When GigaLink ATA boot up it will send TFTP or HTTP request to download configuration files there are two configuration files one is cfg txt and the other is cfg001fc1xxxxxx where 001fc1xxxxxx is the MAC address of the GL VP 62x0 These two files are for initial automatically provisioning purpose only for normal TFTP or HTTP firmware upgrade the following error messages in a TFTP or HTTP server log can be ignored 7 RESTORE FACTORY DEFAULT SETTINGS There are two 2 methods for resetting your unit Reset Button Reset default factory settings following these four 4 steps 1 Unplug the Ethernet cable 2 Locate a needle sized hole on the back panel of the gateway unit next to the power connection 3 Insert a pin in this hole and press for about 8 seconds 4 Take out the pin All unit settings are restored to factory set
12. 9 2011 GigaLink Page 26 of 29 GL GIGALINK GL VP 62x0 User Manual Your changes have been saved Please wait 5 second and then reboot the device E 5 7 Rebooting From Remote The administrator can remotely reboot the unit by pressing the Reboot button at the bottom of the configuration menu The following screen will indicate that rebooting is underway The user can re login to the unit after waiting for about 30 seconds 6 FIRMWARE UPGRADE To upgrade software GL VP 62x0 can be configured with a TFTP server where the new code image is located The TFTP upgrade can work in either static IP or DHCP mode using private or public IP address It is recommended to set the TFTP server address in either a public IP address or on the same LAN with the GL VP 62x0 There are two ways to set up the TFTP server to upgrade the firmware namely through voice menu prompt or via the GL VP 62x0 s Web configuration interface To configure the TFTP server via voice prompt follow section 5 1 with option 06 once set up the TFTP IP address power cycle the ATA the firmware will be fetched once the ATA boots up To configure the TFTP server via the Web configuration interface open up your browser to point at the IP address of the GL VP 62x0 Input the admin password to enter the configuration screen From there enter the TFTP server address in the designated field towards the bottom of the configuration screen Copyright 2009 2
13. ASIC SETTINGS PAGE Setting Options Meaning Port Map Forwards a matching TCP UDP port to a specific LAN IP address with a specific TCP UDP port End User Password This contains the password to access the Web Configuration Menu This field is case sensitive If set to Yes the GL VP 62x0 will respond to the Reply to ICMP on WAN PING command from other computers but it also is port vulnerable to the DOS attack Default is No If this parameter is set to No the HTML configuration WAN Side nip access update via WAN port is disabled You may also access the Device Status page which provides details of the GL VP xxxx product The Device Status page terms are defined in Table 6 Status Page Definitions TABLE 6 Status Page Definitions Copyright 2009 2011 GigaLink Page 12 of 29 GL GIGALINK GL VP 62x0 User Manual MAC Address 00 1tc1 11 23 15 WAN IP Address 192 168 0 15 Product Model Unicom6080 Software Version BOOT 1 1 0 10 2008 06 19 15 19 00 IMG 1 1 0 10 2008 06 19 15 20 00 System Up Time 0 day s 0 hour s 21 minute s 8 second s PPPoE Link Up Disabled NAT Primary indepndent Mapping Port Dependent Fitter Port Hook Registration FXO1 Not Connected Not Registered FXO 2 Not Connected Registered FXO 3 Not Connected Registered Port Status FXO 4 Not Connected Not Registered FXO 5 Not Connected Not Registered FXO 6 Not Connected Not Registered FOI Not Co
14. User Manual GL VP 62x0 Analog IP Gateway 4 or 8 FXO Ports http www giga link com GL GIGALINK GL VP 62x0 User Manual N Table of Content aE eo 3 1 1 Gateway GL VP 62x0 EE eege 3 1 2 Safety ComplianGe Snin annin nhanh n AAA Aa A aaa 3 1 3 Warnanya e ea dee dee 4 PACKAGING acest detedaceretscssecetecsdisetscctucetecsdusedacsiessiessderedscsdeceiecstseaisceisceieseiesedussisastecsiens 4 2 1 Connect The GL VP 62X0 ca aaa ee 4 APPLICATION DESCRIPTION vsscissncssesitecnicsoscasecadsnnsenndsneesniianitasntancdisciusiiesiindsnnienaers 6 3 1 Functional Diagram of IP PBX A GL VP 62X0 s es 6 3 2 GL VP 62x0 Scenario Toll Free Calling Between Locations Own6ka 3aknagka He onpefenena FEATURES vesisccicacisiccsssesicesatecisacisuastesdluccvnadsuniseticusaduaseneisenisnmecucalecsieatiacsousdiedcuaadsescense 7 4 1 Software Features Seege 7 4 2 Hardware Specification ieee irr rr reer mre em mr ar ee ere 8 CONFIGURATION GUIDE oicscteiticatinctnccnccnturatanecnniatrnunmnucwienremnnneunnnnivaunnmcincmunnnnasens 8 5 1 Configuration With Web Browser wissen 8 5 1 1 Accessing The Web Configuration Mem 9 5 2 End User Configuration E 9 5 3 S per User SetliNg E 13 5 3 1 Super User Rn e LE 13 5 4 Configuring The FXO Channels lected dtscuisacldendeencdeecceasteucueucdencati ae 16 5 5 EIDEN 18 5 6 Saving The Configuration Cem ere 26 5 7 Rebooting From Remote savant aide ita ides 27 FIRMWARE UPGRADE seiscsiesssatsssacsassacacantacacesacnai
15. antaiasseaasancdanaeaacaiannaateeateneasecanantnanten 27 RESTORE FACTORY DEFAULT SETTINGG ccccecssesseeeseeeseeeseeesseeeseeeseeeesensees 28 TECHNICAL SUPPORT CONTACT wssssnitetaiisnncsssensiausntadsessndniisansenndaiuswsasedtesnunivnniesnen 29 Copyright 2009 2011 GigaLink Page 2 of 29 GL GIGALINK GL VP 62x0 User Manual 1 WELCOME Thank you for purchasing the GigaLink GL VP 62x0 IP Analog FXO Gateway The GL VP 62x0 is a cost effective easy to use and easy to configure IP communications solution for any business The GL VP 62x0 supports popular voice Codecs and is designed for full SIP compatibility and interoperability with 3rd party SIP providers thus enabling you to fully leverage the benefits of VoIP technology integrate a traditional phone system into a VoIP network and efficiently manages communication costs This manual will help you learn how to operate and manage your GL VP 62x0 Analog IP Gateway and make the best use of its many upgraded features including simple and quick installation multi party conferencing etc This IP Analog Gateway is very easy to manage and scalable specifically designed to be an easy to use and affordable VoIP solution for the small medium business or enterprise 1 1 Gateway GL VP 62x0 Overview The GL VP 62x0 offers an easy to manage feature rich IP communications solution for any small business or businesses with virtual and or branch locations who want to leverage their broadband ne
16. dication will be sent periodically Send Anonymous If this parameter is set to Yes the From header along with Privacy and P_Asserted_Identity headers in outgoing INVITE message will be set to anonymous blocking Caller ID Anonymous Call Rejection Default is No If set to Yes incoming calls with anonymous Caller ID will be rejected with 60x0 Busy message session Default is 180 seconds Expiration Min SE Default is 90 seconds Copyright 2009 2011 GigaLink Page 24 of 29 GL GIGALINK GL VP 62x0 User Manual Caller Request Timer ONo Ces Request for timer when making outbound calls Callae Request Timer No Ces When caller supports timer but did not request one Force Timer ONo OvYes Use timer even when remote party does not support UAC Specify Refresher OQuac Ouas Omit Recommended UAS Specify Refresher UAC OUAS When UAC did not specify refresher tag Force INVITE ONo O Yes Always refresh with INVITE instead of UPDATE Special Feature Standard Volume Amplification Tx Od8 default Rx OdB default PSTN AC Termination 600 Ohm North America v impedance Caller ID Scheme Bellcore Telcordia v Caller IO Minimum RX Level 08 30 50 OdB Default 30d8 Caller ID Transport Type Relay via SIP P Asserted ldentity PIN for PSTN Calls Enter digits to authorize calling PSTN numbers from VOIP no default PIN for VOIP Calis Enter digits to authorize calling VOIP termi
17. f there is no PR service from provider on the FXO line and this setting is configured to Yes calls will not be successful Enable Terminate Call After PSTN Silence Timeout Default is No PSTN Silence Timeout terminate call after long silence detected default is 60 sec max 65536 Min Delay before Dial PSTN Default is 800ms This needs to be equal to or greater than the Current Disconnect threshold setting Once the threshold is reached the gateway can dial out This parameter should only be used if there are PSTN line detection issues DTMF Digit Default value is 110B Volume dB efault value is 11d DTMF Digit Default value is 100ms Length X10ms efault value is 100ms DTMF Dial Default value is 100ms Pause X10ms efault value is 100ms Stage Method 1 2 Syntax ch1 8 1 all channels 1 to 8 are set to value 1 or 2 Stage method can be set to either 1 or 2 Set this parameter to 1if you need to make a direct PSTN call from a VOIP endpoint When you set it to 2 you will first dial one of the VOIP channel accounts from the VOIP endpoint this will result in getting a PSTN line dial tone to then dial out the destination PSTN number Most implementations require this setting to be configured to 1 5 5 Profiles Profiles are basically IP PBX SIP Server configuration templates If you have more than Copyright 2009 2011 GigaLink Page 18 of 29 GL GIGALINK GL VP 62
18. ffer Length Select Low Medium or High based on network conditions No Key Entry Timeout Default is 4 seconds Early Dial Default is No Use only if proxy supports 484 response This parameter controls whether the phone will send an early INVITE each time a key is pressed when a user dials a number Copyright 2009 2011 GigaLink Page 23 of 29 GL GIGALINK GL VP 62x0 User Manual If set to Yes an INVITE is sent using the dial number collected thus far Otherwise no INVITE is sent until the Re Dial button is pressed or after about 5 seconds have elapsed if the user forgets to press the Re Dial button The Yes option should be used ONLY if there is a SIP proxy configured and the proxy server supports 484 Incomplete Address response Otherwise the call will likely be rejected by the proxy with a 404 Not Found error This feature is NOT designed to work with and should NOT be enabled for direct IP to IP calling Dial Plan Prefix Sets the prefix added to each dialed number Use as Send Key Allows users to configure the key as the Send or Dial key If set to Yes will send the number In this case this key is essentially equivalent to the Dial key If setto No this key can be included as part of number Subscribe for MWI Default is No When set to Yes a SUBSCRIBE for Message Waiting In
19. for 7 seconds to reset RESET i factory default settings POWER IN Power adapter connection FXO ports to be connected to physical PSTN lines from PAGI FAJE a traditional PSTN PBX or PSTN Central Office Figure 2 Diagram Of GL VP 62x0 Display Panel Display LEDs FXO port status TABLE 2 Definitions Of The GL VP xxxx Display Panel Indicates Power FONGE LER Remains ON when Power is connected and turned ON Ready LED Remains ON after boot up LAN LED Indicates LAN or WAN port activity WAN LED Indicates PC or LAN port activity LEDs 1 8 degg status of the respective FXO Ports on the back Copyright 2009 2011 GigaLink Page 5 of 29 GL GIGALINK GL VP 62x0 User Manual Busy ON Available OFF NOTE All LEDs display green when ON During a firmware upgrade or configuration download the following LED pattern will be observed Power WAN LEDs will be ON The RUN LED will keep flashing during download and while the new files are written The entire process may take between 5 to 15 minutes The firmware upgrade is complete when you can login into the web configuration pages 3 APPLICATION DESCRIPTION 3 1 Functional Diagram of IP PBX amp GL VP 62x0 Anywhere in the world 4 or 8 Ports r e ZZ QB PSTN Analog endpoints Hantong IP Phones Copyright 2009 2011 GigaLink Page 6 of 29 GL GIGALINK 4 FEATURES GL VP 62x0 User Manual GL VP
20. g ON ms and a pause of OFF ms and then repeat the pattern Restore User can restore the before configuration from the Configuration configuration file saved at local pc Call Progress Tones 5 4 Configuring The FXO Channels Configuring the FXO channels on the GL VP 62x0 is an easy process Follow the GUI interfaces The Device Status page terms are defined in Table 8 FXO Lines Configuration Definitions An example of the Channel Dialing Configuration is shown in Figure 6 Please note the default is always configured The user has the option to change the default settings as described in the Table 8 Copyright 2009 2011 GigaLink Page 16 of 29 GL GIGALINK GL VP 62x0 User Manual FXO PORT Profile ID Ge SIP UserID Authenticate ID Password Name 1 100 100 Profile 1 e 101 101 Profile 1 102 102 Profile 1 103 103 Profile 1 104 104 Profile 1 105 105 Profile 1 106 106 Profile Le Profile liv Enable PSTN Disconnect Tone etection ONo O Yes Default No Disconnect Tone TE f set to yes the following tone is used as the disconnect signal 1 480 32 2 6208 32 c 500 500 Syntax f1 freq vol f2 freq vol c ont loff1 on2 off2 on3 off3 Allowed Range freq 0 to 4000Hz vol 40
21. g three formats Month Day Year Day Month Year Device Mode This parameter controls whether the device is working in NAT router mode or Bridge mode Save the setting and reboot prior to configuring the GL VP xxxx LAN Subnet Mask Sets the LAN subnet mask Default value is 255 255 255 0 LAN DHCP Base IP Base IP for the LAN port which functions as a Gateway for the subnet Default value is 192 168 22 1 DHCP IP Lease Time Value is set in units of hours Default value is 120 hrs 5 Days The time IP address is assigned to the LAN clients DMZ IP Forward all WAN IP traffic to a specific IP address if no matching port is used by GL VP 62x0 or defined in port forwarding Copyright 2009 2011 GigaLink Page 11 of 29 GL GIGALINK GL VP 62x0 User Manual WAN Pong LAN IP LAN Port Protocol UDP v WAN Pen LAN IP LAN Port Protocol UDP x L WAN Port LAN IP LAN Port 3 Protocol UDP Port dep WAN Port LAN IP LAN Port0 Protocol UDP v WAN Pong LAN IP LAN Pong Protocol UDP v WAN Pong LAN IP LAN Port Protocol UDP v WAN Port LAN IP LAN Port Protocol UDP k WAN Port LAN IP LAN Port9 Protocol UDP v End User Password Basic user password to configure this device Reply to ICMP on WAN pon C No Yes Unit will notrespond to PING from WAN side if set to No WAN side http access O No Yes WAN side access to http server will be rejected if set to No SaveSet Reboot WEB LOG IN DEFINITIONS B
22. itch to G 711 Voice Compression G 711U G711A G 723 G 729A B GSM DHCP Server Client Switch Mode and PPPoE Fax over IP T 38 compliant Group 3 Fax Relay up to 14 4kpbs and auto switch to G 711 for Fax Pass through QoS Diffserve TOS 802 1 P Q VLAN tagging Copyright 2009 2011 GigaLink Page 7 of 29 GL GIGALINK GL VP 62x0 User Manual IP Transport RTP RTCP and RTSP PSTN Signaling FXO Loop start Current Disconnect Flexible DTMF transmission method DTMF Method User interface of In audio RFC2833 and SIP Info IP Signaling SIP RFC 3261 Provisioning TFTP and HTTP Control TLS and SIPS pending Management Syslog support remote management using Web browser Short and long haul RENS Up to150 ft on 24 AWG line Caller ID o Type 1 amp 2 ETSI BT NTT and DTMF based Yes Detection only The PSTN lines will need to be subscribed to PR service from the Service Provider GL VP 62x0 EN55022 Class B CFR Part 15 Class B EMC EN55024 GL VP xxxx 6040 FCC CE in addition GL VP 62x0 EN60950 1 GL VP xxxx 6080 UL60950 1 in addition Polarity Reversal Wink Safety 4 2 Hardware Specification TABLE 4 Hardware Specification of GL VP 62x0 LAN interface 2xRJ45 10 100Mbps LED 4or8LEDs GREEN Universal Switching Input 100 240V AC 50 60Hz 0 5A Max Power Adaptor Output 9V DC 2A UL certified Di
23. mension 225mm L x 172mm W x 42mm H Weight 0 29 Ibs 3 5 oz Temperature 32 104 F 0 40 C Humidity 10 90 non condensing Compliance FCC CE 5 CONFIGURATION GUIDE 5 1 Configuration with Web Browser The GL VP 62x0 has an embedded Web server that will respond to HTTP GET POST Copyright 2009 2011 GigaLink Page 8 of 29 GL GIGALINK GL VP 62x0 User Manual requests It also has embedded HTML pages that allow a user to configure the IP phone through any common web browser 5 1 1 Accessing the Web Configuration Menu 1 Connect the Power to the GL VP 62x0 unit 2 Connect an Ethernet cable between the WAN port on GL VP 62x0 to your PC 3 You will have to assign a dummy IP with the same subnet as the GL VP xxxx IP Address which is 192 168 0 160 by default So set an IP address like 192 168 0 x for your PC 4 Launch web browser and type http 192 168 0 160 at address of web browser This connects you to the GL VP 62x0 web server You may choose to use DHCP or PPPoE connection or another static IP address according to your local network environment The Gateway Web Configuration Menu can be then accessed by the following URI http Gateway IP Address where the Gateway IP Address is the IP address of the Gateway NOTE To access the configuration page type the GL VP xxxx IP address into the browser stripping out the leading 0 because the browser will parse in octet e g if the IP address is 192 168 001
24. nals from PSTN no default wt lr Sa at VOIP calis will be forwarded to the specified PSTN number Unconditional Call Forward to Usario Sp cane Et vc 105 a SEU SaveSet El Reboot E PROFILE PAGE DEFINITIONS Setting Options Meaning Caller Reguesi Default is NO Timer Callec Reguesi Default is NO Timer Force Timer Default is NO UAG Speciiy Default is Omit Refresher UAS SPeely Default is UAC Refresher Force INVITE Default is NO Default is Standard Choose the selection to meet some Special Feature special requirements from Soft Switch vendors like Nortel Broadsoft etc Handset volume adjustment RX is for receiving volume TX is for transmission volume Default values are OdB for both parameters 6dB generates the highest volume and 6dB generates the lowest volume Volume Amplification PSTN AC Default is 600 Ohm North America Termination Copyright 2009 2011 GigaLink Page 25 of 29 GL GIGALINK GL VP 62x0 User Manual Caller ID Scheme Select the Caller ID Scheme to suit the standard of different area e Bellcore North America e ETSI FSK France Germany Norway Taiwan UK CCA e ETSI DTMF Finland Sweden e DTMF Denmark Caller ID Minimum RX Level dB Default is 30dB Caller ID Transport Type Default is relay via From header You may also select relay via P_Asserted_lIdentity header Disable Caller ID feature
25. nd Service Representative for a RMA Return Materials Authorization number GigaLink reserves the right to remedy warranty policy without prior notification 2 PACKAGING Unpack and check all accessories The GL VP 62x0 package contains gt One GL VP 62x0 VoIP adapter gt One universal power supply gt One Ethernet cable 2 1 Connect the GL VP 62x0 Managing the GL VP 62x0 gateway and connecting the unit to the VoIP network is very simple Follow these four 4 steps to connect your GL VP 62x0 gateway to the Internet and access the unit s configuration pages 1 Connect PSTN Line to the FXO1 FXO8 ports 2 Insert the Ethernet cable into the WAN port of GL VP 62x0 and connect the other end of the Ethernet cable to an uplink port a router or a modem etc 3 Connect a PC to the LAN port of GL VP 62x0 for initial configuration or if it is being used as a router 4 Plug the power adapter into the GL VP 62x0 and into a power outlet Figure 1 Diagram of GL VP 62x0 Back Panel Copyright 2009 2011 GigaLink Page 4 of 29 GL GIGALINK GL VP 62x0 User Manual Wen Aaii 4604 I Td AE LAN WAN Power Reset Supply Ports TABLE 1 Definitions Of The GL VP xxxx Connectors Connect your PC to this port It will then be assigned an LAN or PC IP address from your Router DHCP Server The GL VP 62x0 acts as a switch only WAN or LAN Connect to the internal LAN network or Public Internet Factory Reset button Press
26. nnected Not Registered FXO 8 Not Connected Not Registered STATUS PAGE DEFINITIONS Setting Options Meaning MAC Address The device ID in HEX format This is needed for ISP troubleshooting Note there are separate MAC addresses for the WAN side and the LAN side WAN IP Address Shows WAN IP address of GL VP 62x0 Product Model Contains the product model info Software Version Program This is the main software release Boot and Loader are not changed often System Up Time Shows system up time since the last reboot PPPoE Link Up Shows whether the PPPoE connection is running if connected to DSL modem NAT Shows type of NAT the GL VP 62x0 is connected to via its WAN port It is based on STUN protocol Port Status Shows several information regarding the individual FXO ports 5 3 Super User Settings 5 3 1 Super User Configuration The end user needs to login to the Super user configuration page the same way as for the basic configuration page Copyright 2009 2011 GigaLink Page 13 of 29 GL GIGALINK GL VP 62x0 User Manual Super User configuration includes the end user configuration and Super configurations including SIP configuration Codec selection NAT Traversal Setting and other miscellaneous configuration k Admin Password Home NPA ayer 3 QoS Layer 2 QoS STUN server is keep alive interval Firmware Upgrade and Provisioning purposely not displayed for security
27. protection 48 Diff Serv or Precedence value 802 1 VLAN Tan 802 1p priority value 0 0 7 URI or IP port 20 in seconds default 20 seconds Upgrade Via TFTP HTTP Firmware Server Path 192 165 0 169 Config Server Path 192 168 0 169 Firmware File Prefix Firmware File Postfix Config File Prefix Config File Postfix Automatic Upgrade O No Yes check for upgrade every 7 minutes default 7 days Ate Always Check for New Firmware Check New Firmware only when FAN pre suffix changes TABLE 7 Super Configuration Page Definitions SUPER CONFIGURATION PAGE DEFINITIONS Setting Options Admin Password Meaning This contains the password to access the Super Web Configuration page This field is case sensitive Home NPA Local area code for North American Dial Plan This field defines the layer 3 QoS parameter which can be the Layer 3 QoS value used for IP Precedence or Diff Serv or MPLS Default value is 48 This contains the value used for layer 2 VLAN tag Layer 2 QoS A Default setting is blank STUN server is IP address or domain name of stun server keep alive interval This parameter specifies how often the GL VP 62x0 sends a blank UDP packet to the SIP server to keep the hole on the NAT open Default is 20 seconds Firmware Upgrade and Provisioning Default method is HTTP Firmware upgrade may take up to 10 minutes depending on network environment
28. s of audio Similarly if this field is set to be 2 and if the first vocoder chosen is G729 or G711 or G726 then the ptime value in the SDP message of an INVITE request will be 20ms If the configured voice frames per TX exceeds the maximum allowed value the GL VP 62x0 will use and save the maximum allowed value for the corresponding first vocoder choice The maximum value for PCM is 10 x10ms frames for G726 it is 20 x10ms frames for G723 it is 32 x30ms frames for G729 G728 64 x10ms and 64 x2 5ms frames respectively G723 Rate Defines the encoding rate for G 723 vocoder By default 6 3kbps rate is chosen iLBC frame size Sets the iLBC frame size in 20ms or 30ms iLBC payload type Defines payload type for iLBC Default value is 97 The valid range is between 96 and 127 G726 16 Payload Type Default value is 97 Range is from 96 to 127 G726 24 Payload Type Default value is 99 Range is from 96 to 127 G726 40 Payload Type Default value is 103 Range is from 96 to 127 Copyright 2009 2011 GigaLink Page 22 of 29 GL GIGALINK G729E Payload Type 1102 VAD No Symmetric RTP O No Fax Mode T 38 Fax Tone Detection Mode Jitter Buffer Type Jitter Buffer Length Low No Key Entry Timeout 4 Early Dial No Dial Plan Prefix Use as Dial Key O No SUBSCRIBE for MWI E LA Yes Send Anonymous No Anonymous Call Rejection No Session Expiration
29. tings IVR Command Reset default factory settings using the IVR Prompt Table 5 1 Dial for voice prompt 2 Enter 99 and wait for reset voice prompt 3 Enter 862584658050 NOTE 1 Factory Reset will be disabled if the Lock keypad update is set to Yes Copyright 2009 2011 GigaLink Page 28 of 29 GL GIGALINK GL VP 62x0 User Manual 2 Please be aware by default the GL VP 62x0 WAN side HTTP access is disabled After a factory reset the device s web configuration page can be accessed only from its LAN port 8 TECHNICAL SUPPORT CONTACT Email support giqa link ru Copyright 2009 2011 GigaLink Page 29 of 29
30. to 24dBm Default Busy Tone f1 480 32 f2 620 32 c 500 500 Enable Polarity Reversal Disconnect Omno Yes Default No Check with your PSTN carrier before set to Yes a Cat AS ESTN No Yes Default No rem Silence Timeout co __ sec terminate call after long silence detected default is 60 sec max 65536 stage Method 1 2 chl 8 1 default 1 1 stage dialing TABLE 8 FXO Lines Configuration Definitions FXO PORT SETTING Setting Options Meaning FXO Port FXO Port Number SIP User ID User account information provided by VolP service provider ITSP Usually in the form of digit similar to phone number or actually a phone number SIP service subscriber s Authenticate ID used for authentication Can be identical to or different from Authenticate ID SIP User ID Password SIP service subscriber s account password for GL VP 62x0 to register to SIP servers of ITSP Name Name Copyright 2009 2011 GigaLink Page 17 of 29 GL GIGALINK GL VP 62x0 User Manual Profile ID Select the corresponding Profile ID 1 2 Enable PSTN Disconnect Tone Default is No Detection PSTN Disconnect Tone Default Busy Tone f1 480 32 f2 620 32 c 500 500 Enable Polarity Reversal Disconnect Default is No This should be set to Yes only if the FXO lines are subscribed to PR service from PSTN Service provider It is merely a PR detect feature Note I
31. twork and or add new IP Technology to their current phone system The GigaLink Enterprise Analog VolP Gateway GL VP 62x0 series converts SIP RTP IP calls to traditional PSTN calls and vice versa There are two models the GL VP 6240 and GL VP 6280 which have either 4 or 8 FXO ports respectively The installation is the same for either model Caution Changes or modifications to this product not expressly approved by GigaLink Technology or operation of this product in any way other than as detailed by this User Manual could void your manufacturer warranty Information in this document is subject to change without notice No part of this document may be reproduced or transmitted in any form or by any means electronic or mechanical for any purpose without the express written permission of GigaLink Technology 1 2 Safety Compliances The GL VP 62x0 is compliant with various safety standards including FCC CE Its power adaptor is compliant with UL standard Warning use only the power adapter included in the GL VP 62x0 packages Using an alternative power adapter may permanently damage the unit Copyright 2009 2011 GigaLink Page 3 of 29 GL GIGALINK GL VP 62x0 User Manual 1 3 Warranty GigaLink has a reseller agreement with our reseller customer End users should contact the company from whom you purchased the product for replacement repair or refund If you purchased the product directly from GigaLink contact your GigaLink Sales a
32. ult setting is Yes Unregister on Reboot Default is No If set to Yes the SIP user s registration information is cleared on reboot Register Expiration Allows the user to specify the time frequency in minutes for the GL VP 62x0 to refresh its registration with the specified registrar The default interval is 60 minutes or 1 hour The maximum interval is 65535 minutes about 45 days Outgoing Call without Registration Default is No If set to Yes user can place outgoing calls even when not registered if allowed by ITSP but is unable to receive incoming calls Local SIP port Defines the local SIP port the GL VP 62x0 will listen and transmit The default value for Profile 1 is 5060 and 6060 for Profile 2 Local RTP port Defines the local RTP RTCP port pair the PROFILE will listen and transmit It is the base RTP port for channel 0 When configured channel 0 will use this port _ value for Copyright 2009 2011 GigaLink Page 20 of 29 GL GIGALINK GL VP 62x0 User Manual RTP and the port_value 1 for its RTCP channel 1 will use port_value 2 for RTP port_value 3 for its RTCP and so on The default value for Profile 1 is 5004 and 6004 for Profile 2 Use Random Port This parameter when set to YES will force random generation of both the local SIP and RTP ports This is usually necessary when multiple GL VP 62x0 are behind the same NAT
33. x0 User Manual one IP PBX system or SIP Server that you would like to use with the GL VP 62x0 then you can configure Profile 2 or 3 Note Make sure you select the correct profile for each channel under Channels WEBPAGE TABLE 9 Profile Page Definitions Account Active ONo Yes SIP Server e g sip rmycompany com or IP address Outbound Proxy 192 168 0 101 e g proxy myprovider com or IP address if ary NAT Traversal ONo No butsendkeep alve COSTUN OUPNP Connect to Asterisk ONo Yes Use DNS SRV No Ces User ID is phone number ONo Ces SIP Registration ONo Yes Unregister On Reboot No Oves Register Expiration 2 in minutes default 1 hour max 45 days Reyaketon Ono Oves local SIP port 5060 default 5060 local RTP port 5004 1024 65535 default 5004 Use random port No Ces Refer To Use Target Contact No Yes DTMF Payload Type 101 DTMF in Audio ONo Yes PROFILE PAGE DEFINITIONS Setting Options Meaning Account Active When set to Yes the SIP Profile is activated SIP Server s IP address or Domain name provided by SIP Server VoIP service provider IP address or Domain name of Outbound Proxy or Media Gateway or Session Border Controller Used by GL VP 62x0 for firewall or NAT penetration in different network environments If symmetric NAT is detected STUN will not work and ONLY outbound proxy can correct the problem Outbound Proxy This parameter defines whether
Download Pdf Manuals
Related Search