POW-AD22GY, POW
Contents
1. LED Indicator 2 piece power input connector detachable A dedicated plug as a standard item DC Output Screw in type cable connection 2 piece power output connector detachable A dedicated plug as a standard item Screw in type cable connection LED Indicator AC Input ON DC output on Power LED Power green OFF DC output off CONTEC POW AD22GY POW AD13GY 4 POW AD22GY POW AD13GY User s Manual System Reference Specifications2 Item POW AD22GY POW AD13GY Current ACIN 100V 0 3A Typ Io 100 ACIN 100V 0 4A Typ Io 100 ACIN 200V 0 2A Typ Io 100 Rush current ACIN 100V 15A Typ Io 100 ACIN 100V 25A Typ Io 100 a T ACIN 200V 30A Typ Io 100 Leakage current 0 5mA Max 60Hz IEC60950 0 18mA Max ogee 60Hz IEC60950 75 Typ 8 0A Max 20mV Max 40mV Max 120mVp p Max Ambient temperature 50mV Max 0 55 C fluctuations Time dependent 20mV Max It is change of the 30 0mV Max It is change of the 30 drift minute 8 hours after input voltage minute 8 hours after input voltage impression in the circumference impression in the circumference temperature of 25 C and rated input temperature of 25 C and rated input and output and output 700ms Max ACIN 85V Ilo 100 holding time 8ms Typ ACIN 100V Io 100 10ms Typ ios a 16ms Typ ACIN 200V Io 100 Auxiliary Overcurrent protection Operates at 125 Min of rated Operates at 1052. of rated functions Seer current auto reverting current auto reverting Overvoltage protection Operates at 115 Min of rated Other oe Cooling method Natural air cooling It is seven years Io 75 at the circumference temperature of 25 C Weight of the system 110g 150g unit Installation method One touch attachment to a 35mm DIN rail The mounting mechanism is provided on the system unit as a standard item CONTEC POW AD22GY POW AD13GY POW AD22GY POW AD13GY User s Manual Installation Environment Requirements 10 90 RH No condensation None Noise AC line 2kV Signal line 1kV IEC1000 4 4Level 3 EN61000 4 4Level 3 immunity Contact discharge 4kV IEC1000 4 2Level 2 EN61000 4 2Level 2 resistance Atmospheric discharge 8kV IEC1000 4 2Level 3 EN61000 4 2Level 3 Vibration Sweep resistance resistance 80minutes each in X Y and Z directions JIS C0040 compliant IEC68 2 6 compliant Impact resistance 15G half sine shock for 11ms in X Y and Z directions JIS C004 compliant IEC68 2 27 compliant Class D grounding previous class 3 grounding Installation location Installing to the DIN rail the control boards etc as the power supply dedicated to the F amp elT I O Connectors Deseription Input 5 08mm pitch 12 0A rated current Compatible plug Laterally operable screw in type freien amarei aaiem Pomme costacrom Output Laterally operable screw in type MC1 5 3 ST 3 5 made by PHOENIX CO
3. F amp eIT Series AC DC Power Supply Unit POW AD22GY or POW AD13GY User s Manual CONTEC CO LTD Congratulations on your recent purchase of a AC DC Power Supply Unit Copyright Copyright 2001 CONTEC CO LTD ALL RIGHTS RESERVED No part of this document may be copied or reproduced in any form or by any means without prior written consent of CONTEC CO LTD CONTEC CO LTD makes no commitment to update or keep current the information contained in this document The information in this document is subject to change without notice All relevant issues have been considered in the preparation of this document Should you notice an omission or any questionable item in this document please feel free to notify CONTEC CO LTD Regardless of the foregoing statement CONTEC assumes no responsibility for any errors that may appear in this document or for any results of using the product F amp elT is a registered trademark of CONTEC CO LTD Other company and product names mentioned herein are generally trademarks or registered trademarks of their respective owners Trademarks All company and product names that are referred to in this manual are generally trademarks or registered trade Handling Precautions N CAUTION This power supply is dedicated to the F amp eIT Do not use for the other devices Do not use or store the equipment in a hot or cold place or in a place that is subject to severe temperature changes Operating temper
4. NTACT Corp External Dimensions CONTEC POW AD22GY POW AD13GY POW AD22GY POW AD13GY User s Manual Installation Method Mounting the AC DC Power Supply Unit on the DIN Rail Mounting procedure 1 Pushing the fixing hook with a flat blade screwdriver renders it into a lock enabled condition Press here to lift the fixing hook 2 Hook the AC DC power supply unit from the upper part of the DIN rail and press the lower part of the unit against the DIN rail Side view 3 The fixing hook is automatically locked and the module can be mounted in one touch Side view Removal procedure 1 Lower the fixing hook for the unit to unlock it 2 With the fixing hook unlocked pull the lower part of the unit toward you Side view 3 By lifting the unit you can easily remove it from the DIN rail Side view CONTEC POW AD22GY POW AD13GY POW AD22GY POW AD13GY User s Manual Connection Method Connecting the I O cables to the AC DC power supply unit Cables are connected to the AC DC power supply unit by means of detachable connectors that are provided as standard items Input unit compatible cables AWG 24 12 Tightening torque 0 5 0 6Nm Output unit compatible cables AWG 28 16 Tightening torque 0 22 0 25Nm The AC DC power supply unit and F amp eIT Series product can be cable connected using the detachable
5. ature range 0 50 C Do not use or store the equipment in a place subject to direct sunlight or near a heating device such as a stove Do not use or store the equipment in a dusty or humid place Operating humidity range 10 90 RH No condensation As this product contains precision electronic components do not use or store in environments subject to shock or vibration Do not use or store the product near equipment generating a strong magnetic field or radio waves If you notice any strange odor or overheating please unplug the power cord immediately In the event of an abnormal condition or malfunction please consult the dealer from whom the equipment was purchased CONTEC POW AD22GY POW AD13GY POW AD22GY POW AD13GY User s Manual To avoid electric shock please do not touch the system with a wet hand Do not modify the unit CONTEC will bear no responsibility for any problems etc resulting from modifying this unit Do not open the unit casing CONTEC will disclaim any responsibility for equipment whose casing has been opened When disposing of the product follow the disposal procedures stipulated under the relevant laws and municipal ordinances Product Configuration System unit 1 AC Power Supply input connector plug 1 User s Manual 1 DC Power Supply output connector plug 2 About the POW AD22GY or POW AD13GY The POW AD22GY or POW AD13GY is a compact power supply unit de
6. connector that is provided on either the unit face or the modulet face compatible cables AWG 28 16 Please use the clothing of a cable turning to it about about 7mm CAUTION Because the AC DC power supply unit generates heat a minimum spacing of 2 0 cm should be provided between the POW AD22GY or POW AD13GY and any adjoining units and care should be taken so that the ventilation holes are not covered Cable connection List of Options FAN Unit FAN FIT FAN Unit For 52 4mm width unit or module Copyright 2001 CONTEC CO LTD ALL RIGHTS RESERVED CONTEC CO LTD March 2009 Edition 3 9 31 Himesato Nishiyodogawa ku Osaka 555 0025 Japan Japanese http www contec co jp English http www contec com A 40 623 LZN6032 Chinese _ http www contec com cn 03192009_rev6 11272001 No part of this document may be copied or reproduced in any form by any means without prior written consent of CONTEC CO LTD
7. he risk of insulation failure The insulation on the POW AD22GY is designed to deal with pollution degree 2 and therefore the unit should only be used in environments with pollution degree 2 or better Pollution degree 1 Dry environment with no conductive dust or other contamination Pollution degree 2 Environment in which conductive dust or other contamination does not normally occur but where conductive contamination may occur from time to time due to accumulation of dust or similar Typically the environment in an IP54 equivalent control panel in a factory control room or factory floor Pollution degree 3 Environment in which conductive dust or other contamination does occur and where conduction may occur due to accumulation of dust or similar Typically a factory floor environment Pollution degree 4 Environment in which conductive contamination such as rain or snow is always present An outdoor environment As described above if a POW AD22GY is housed in an IP54 equivalent control panel contamination level 2 can be achieved 3 Installation Requirements a Build in this power supply according to standard EN60950 which is a built in power supply b Installation category 2 Pollution Degree 2 c The protection earth point is FG pin of 100 240VAC connector in front of the case Ground this pin to the earth with the cable CONTEC POW AD22GY POW AD13GY POW AD22GY POW AD13GY User s Manual Nomenclature Connector
8. rve necessary safety precautions The following describes the main points to note so that installations using the POW AD22GY can comply with the low voltage directives Although this information has been prepared to the best of our ability based on the requirements standards and other stipulations contained in the regulations obtained by CONTEC we provide no guarantee that equipment manufactured based on this information will comply with the above directive Ultimate responsibility for determining how to comply with the low voltage directive and how to confirm compliance is the responsibility of the equipment manufacturer POW AD22GyY is an open type device a device designed to be housed inside other equipment and must always be mounted inside a control panel according to standard EN60950 To provide electrical shock protection for people such as operators who do not have the necessary level of electrical knowledge the control panel must include the following precautionary measures Installation category 2 1 Electric shock protection a Lock the control panel to ensure that it can only be opened by persons with sufficient knowledge and training on electrical equipment b Incorporate a mechanism so that opening the control panel automatically isolates the power supply 2 Water and dust proofing The control panel is dust and water proof If dust proofing or water proofing is made inadequate insulation may deteriorate increasing t
9. signed to supply DC power to the F amp elT series of products This AC DC power supply unit is carrying out the standard equipment of the DIN rail attachment mechanism to the main part like other products of this series and can install it simply and smartly AC input can prepare 85 132V POW AD13GY and wide range 85 264V POW AD22GY and can unite and choose them as a system In addition a system can be easily built combining F amp elIT series product FCC PART 15 Class A Notice NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference at his own expense WARNING TO USER Change or modifications not expressly approved the manufacturer can void the user s authority to operate this equipment CONTEC POW AD22GY POW AD13GY POW AD22GY POW AD13GY User s Manual Compliance Requirements The low voltage directives require that devices operating from power supplies in the range 50 1000 VAC or 75 1500 VAC obse
Download Pdf Manuals
Related Search