20151016 ~ FORBO-EUROCOL-NL ~ 716-eurodur-hp
Contents
1. eurocol the strong connection eurocol 716 716 EURODUR HP T Very strong cement based grouting cement with high abrasion and a high chemical resistance Product Typification Basis Cement based powder with special additives and a high synthetic binder content to be mixed with water Colour Grey Consistency After mixing asmooth and homogeneous mixture Self compacting grouting system A very high chemical resistance in comparison with the standard cement based grouts Very wear proof High bending and compression strength Frost and moisture resistant Suitable for high pressure cleaning For in and outdoor use For wall and floor tiles Suitable for almost all subfloors Joint width from 2 to 10 mm Performances Classification Complies with CG2W Ar according to NEN EN 13888 Cleaning 716 Eurodur HP is resistant against domestic cleaners with a pH value of 7 or higher resistance Resistance Compare with the collection of other cement based grouts 716 Eurodur HP has a high chemical resistance The product is test and resistant against bases lt 10 conc weak acids lt 2 solvents limited ethyl acetate and oils Aging 16 Eurodur HP does not deteriorate with age Consumption gt 600 2 500 g m depending on the size of the tile joint width and depth The following formula will enable you to calculate the required quantity of grouting cement per m joint width mm x joint depth mm x joint le2. few minutes stir once again and apply the mixture into the joints Drying time Depending on the temperature and subfloor the hardening to a low tension and somewhat flexible joint takes place within 1 2 hours Shelf Life 12 Months in unopened packaging After use close the open packaging well Application From 5 to 25 C temperature of the surrounding as well as the subfloor temperature The mentioned values have been established in our laboratory and must be considered as guidelines in view of possible variations in climatic circumstances subfloor compositions and layer thickness User manual e Foran optimal final result the joints must be free from adhesive and or mortar residues When grouting the subfloor adhesive or mortar should be sufficiently dry e Tiles fixed with adhesive can be grouted after 24 hours Wall tiles fixed in the mortar can be grouted after minimum 4 days Floor tiles fixed in the mortar can be grouted immediately Following these regulations drying of the joints will take place equally e Fora good quality of the joint the water powder mixing ratio is very important Add 25 kg of 716 Eurodur HP to approx 5 litres wall and 5 5 litres floor of cool and clean tap water and stir the mortar for approx 2 minutes by using an electric stirrer approx 600 rpm to a smooth and homogeneous mixture After stirring wait for a few minutes and stir once again This gains an optimal application and an extended p
3. he grouting Wet the tiles and the grouting thoroughly before applying the cleaning product The cleaning product will then not penetrate so deeply into the grouting e Rub the tiles clean preferably using a non acidic cleaning product Work according the guidelines of the manufacturer e After cleaning the tiles rinse them thoroughly with tap water and dry them with a cloth Quality and guarantee Environment and health Safety and environment Safety data sheets of Forbo Eurocol products according to EEG guideline 91 155 Articles Article Definition Packaging EAN code 716 Eurodur HP Grey 25 kg 8 710345 716253 The 716 Eurodur HP is available in the colour grey Eurocol is part of the Forbo Group RADO
4. ngth per m m1 x specific weight 1 7 x extra expenditure factor 1 5 g m Discoloration The colour on the packaging and colour key is an indication The prepared mortar can have an other colour In doubt always make a test Since at the same time a number of factors may affect adversely the colour Forbo Eurocol Nederland B V takes no responsibility for colour deviations When using several packaging always use the same charge number Application Cement based grouting cement for jointing ceramic wall and floor tiles natural stone and mosaic where high demands towards the wear and chemical resistance are required Joint width of 2 to 10 mm Suitable on almost all stony and gypsum based subfloors as well as sheet material Applicable in wet areas professional kitchens swimming pools various industrial applications balconies and terraces Resistant against high pressure purification up to 100 bar Suitable for underfloor heating systems Working Process Eurocol is part of the Forbo Group RADO eurocol the strong connection Storage Store cool and dry in unopened packaging Mixing ratio Add 25 kg 716 Eurodur HP to approx 5 0 wall and 5 5 floor litres of water Processing time Bij een temperatuur van ca 20 C de aangemaakte voegmortel binnen 30 minuten na het aanmaken verwerken Hogere temperaturen verkorten de verwerkingstijd lagere temperaturen verlengen deze Latency After mixing with water wait a
5. otlife e Apply the mortar within 30 minutes fully into the joints with a grouting trowel Remove excess material immediately Do not add extra water to the bonding mortar Remixing without adding water is permitted e After grouting wait until the grout will turn somewhat dull Depending on the circumstances temperature relative humidity type of tile and subfloor this will take place after 5 to 45 minutes Clean tiles with a clean and moist sponge The joint should be sufficiently dry otherwise the joint will be washed out Tip When no mortar is left on your finger after touching the material with a fingertip the joint is ready for sponging e Ifin doubt about cleaning the tiles and adhesion of the grouting material on e g strong profiled or non skid tiles make a test Moisten the entire tile work with a rotating movement with a light moist sponge or sponge float and wait for approx 1 minute Through this the residual cement haze can easily be removed from the tile work When using a sponge bucket and sponge float roll these thoroughly dry e Thereafter finish tight with sponge Make sure all joints are touched Thereafter clean the tile work in a diagonal direction with a clean and light moist sponge When dry use a clean and dry cloth for the finishing polish For an optimal strength prevent accelerated drying of the mortar through warmth draught high absorption etc by wetting the joints once or several times within 24 hours e Afte
6. r grouting wait 3 4 hours before walking on the floor After 24 hours the tile work is fully accessible Maintenance Taking care of the grouting For cleaning grouts and to remove any mould use a mould removal product These products have a chlorine bleach base and are especially suitable for the use concerned Cleaning products with a chlorine bleach base have a pH value of 7 neutral or more These products will not harm the grouting Some cleaning products such as green soap always leave a greasy film to which dirt can easily adhere These products are also not suitable Removing limescale Limescale can form on tiles and on the surface of sanitary fittings in regions where the tap water is hard Almost all limescale removal products are acidic products and have a pH value which is too low These products will harm cement bound grouting every time it is cleaned Even when diluted the pH value of these products is still too low The level of a liquid s acidity is indicated by a pH value of between 0 14 Liquids with a neutral level of acidity such as tap water have a pH value of 7 Contact the manufacturer if the pH value of the cleaning product is not stated on the packaging Forbo Eurocol Nederland B V recommends the following when cleaning tiles Eurocol is part of the Forbo Group RADO eurocol the strong connection Only use a cleaning product in the places where limescale and other dirt is visible on the tiles and t
Download Pdf Manuals
Related Search