Home
User Manual SCB-12
Contents
1. o quie In order to achieve the best picture quality you must set the outputs of the SCB 12 to match the native resolution of your display unit e g LCD or DLP projector or monitor Important What matters is the native resolution of the projector or monitor not the maximum resolution that it can display in com pressed mode The native resolution is the actual number of pixels of the built in LCD display or DLP chip of a projector or monitor Most LCD or DLP projectors can also display higher resolutions than their native resolution but only in compressed mode and with inferior picture quality Do NOT set the output of the SCB 12 to a higher standard than the native resolution of your display unit If you output the SCB 12 image on a CRT monitor or CRT projec tor use an output mode with 75 or 85Hz because 60Hz may show a slight image flickering For LCD DLP projectors or monitors and video conferencing units 60Hz is the best choice If you are unsure what the best mode is read the user manual of the connected units Do not set a higher refresh rate than your monitor or projector can display otherwise the monitor or projector can be damaged Follow the instructions in the user manual of the connected units For optimum color reproduction set the display device to sRGB standard With none RGBs display devices may it is necessary to change the gamma setting in the on screen menu see page 29ff For corre
2. Pins 2 RX 3 TX 5 GND Baud rate 9200 19200 38400 57600 or 115200 selectable databits 8 stopbit 1 The baud rate can be changed in the on screen extra menu see page 29ff The complete command protocol can be found on our internet website under www wolfvision com support Version 1 5 24 wore vision Connections 7 5 Cd quie External Infrared IR Sensor In some rooms one IR receiver may not be sufficient In this case connect the external IR receiver to the IR SENSOR plug 9 and position the IR sensor somewhere on the ceiling or in the room where users normally point the remote control towards The external IR receiver is included in the test set and is available as an optional accessory USB The USB device port Z5 can be used for direct connections be tween the SCB 12 and a computer This way SCB 12 can be con trolled and can be used as a scanner for 3 dimensional objects Images in JPG TIF or BMP format can be taken in a fraction of a second much faster than with a desktop scanner WolfVision s USB Software Connectivity Software works under Windows 2000 XP Vista and 7 32 and 64 bit as well as Apple Macintosh It is fully TWAIN WIA compatible This is important when using the SCB 12 in connection with graphic programs such as Photoshop or for connecting them to Interactive Whiteboards Smart Boards The fast USB 2 0 port can also output live
3. Returns to previous menu page Version 1 5 34 wouFVsion OSD Detail Adjust sharpness of image Factory setting is HIGH Possible settings are e HIGH highest contour sharpness of image with most details e MEDIUM average contour sharpness e OFF contour sharpness is de activated for soft contours with fewer details Resolution Change Output wourvsion SCB 12 CHANGE OUTPUT Lad DVI RGB Resolution AUTO Resolution Test Ok eo Cancel DVI RGB Resolution Resolution and refresh rate vertical freguency Factory setting is AUTO Possible settings are e AUTO automatic adjustment of optimal resolution and refresh rate depending on the connected display device according to the VESA standard e Manual setting of resolution and refresh rate VGA 60 to 1080p 60 Before changing the resolution with Ok select the line Resolu tion Test to check capability of connected display device For automatic adjustment of resolution and refresh rate a full con nected cable is needed DDC lines More information regarding resolution and refresh rate can be found on page 54 Edo Resolution Test Selected resolution will be activated for 10 seconds afterwards the units switches back to previous setting This would be helpful to check if the connected display device is capable to show the de sired resolution Activated test procedure cannot be aborted manually it retu
4. 205 Westwood Ave Long Branch NJ 07740 KO Phone 866 834 BOARDS 26273 1 732 222 1511 Fax T32 222 7088 E mail sal sittouchboards com use TRIGGER LJ LAN RGB m A dl o POWER Kei SY USERMANUAL SCB 12 Version 1 5 Table of Contents Table of Contents l Copyright Informaltion 2 00N r sk ia esate PLS IO V ik n pi ap K ryha 4 H About this user manual I U HE HEHE 4 Il Symbols in this manual ll uu U U Q u 5 1 CU LU l U OKO U u U uu uuu uu u 6 1 1 Labels on the remote control optional 7 1 2 Approval marks on the unit uuu Uu unuqa iisas nev pr bl 7 2 Contents of packaging IILI III tnc d kos ek ano sein anan skeans koni ssonn n 8 2 1 SCB 12 standard S8t uu eem i ke sak kayo ERE veye SERRE sak Reece 8 2 2 DOB 2 TEST SOU r I 8 3 Features 9 3 1 deis en 9 4 Pin assignment M nn HE HEHE HE HERNE 12 4 1 mI ide wk and kado svp ke depa danti kadna ap edad ue SE ENEE un Sak SS S 12 4 2 FON ches trik E 13 4 3 soie 14 4 4 Interface Board optional emen nnne 15 4 5 Infrared Remote Control 16 5 FUNCTIONS m 18 5 1 ZOOM rccte LR LM eebe 18 5 2 Auto Iris Manual is 18 5 3 FOCUS AUIOTIOCUS TM 18 5 4 Preset RU
5. AUTO MED adjusts gain level for optimum image quality and depth of focus automatically AUTO HIGH adjusts the highest necessary gain level for high est depth of focus automatically 0dB to 18dB in steps of 1dB Exposure time Factory setting is AUTO Possible settings are OFF full exposure time STEP user defined exposure time in coarse steps STEP FLICKERLESS prevents flickering of image in 50Hz and 60Hz countries caused by fluorescent lamps VARIABLE user defined exposure time in fine steps e g for scanning computer monitors AUTO Best shutter setting is chosen automatically by the SCB 12 flickering can occur with fluorescent lamps Factory setting is AUTO Possible settings are AUTO whenever a zoom key is pressed the SCB 12 switches Auto Iris ON MANUAL Auto Iris stays disabled until the device is switched off on or a preset with enabled Auto Iris is recalled When a zoom key is pressed Auto Iris stays off wovrVsion 31 Version 1 5 OSD Image Brightness Back Light Compensation Extern Trigger Extern Trigger Edge Return d Sets brightness of picture when Auto Iris is used 10 darkest and 10 brightest image Optimum setting also de pends on connected display device Factory setting is 0 Possible settings are e 10 to 10 in integer steps Changes the behavior of the Auto Iris control to change the bright ness reference to darker areas of the image Optimum setting d
6. The LASER indication LED 20 shows the selected code it flashes one time for code A two times for code B three times for code C and four times for code D Version 1 5 56 wouFVsion Transport 10 4 1 10 4 2 10 5 Cleaning Disconnect the unit from the mains Cabinet WARNING Damaging the unit Strong cleaning agents like acetone benzene or similar damages the finish gt Use cleaning agents like display cleaner only Remove dust and dirt by gently wiping with a soft lint free cloth Optic Lens WARNING Damaging the unit Strong cleaning agents like acetone benzene or similar damages the anti reflex coating Paper tissues can scratch the lens gt Use soft lint free cloth with special optical cleaning agent only Clean the lenses by gently wiping with a soft lint free cloth do not use a paper tissue Clean by breathing on the lens to create mois ture then wipe with a lint free cloth If need be use a special optical cleaner only Transportation WARNING Damaging the unit gt Pack the unit always in the original packaging Ask your WolfVision dealer or WolfVision office to answer any questions wourVision 57 Version 1 5 Technical Specification 11 Technical Specifications Camera Technology Pictures per second as picked up by the camera 1 CCD 1 3 Progressive Scan 30 fps full pict
7. Adjust the color saturation to desired value Higher values result in more color full images e 0 to 150 in integer steps 105 standard setting To toggle Black White mode frequently program this function to a preset key in the preset control menu see page 35 Alternative image display Select positive negative conversion for photo negatives negative with blue background for good text readability To toggle this func tion frequently program it to a preset key in the preset control menu Factory setting is POSITIVE Possible settings are e POSITIVE positive normal image display e NEGATIVE negative inverse image display for photo nega tives e BLUE negative with blue background for better readability of texts e g written with pencil Color or black white image reproduction For black white objects like x rays or text use black white mode To toggle this function frequently program it to a preset key in the preset control menu Factory setting is POSITIVE Possible settings are e COLOR colored image reproduction e BLACK WHITE black white image reproduction Returns to previous menu page Output Settings wovrVsion SCB 12 OUTPUT SETTINGS A Detail HIGH Ll DVI RGB Resolution AUTO Return DVI is SXGA 60Hz Sharpness Aperture Contrast of the displayed image Changes resolution settings of DVI and RGB port Shows the current selected resolution and refresh rate of DVI RGB
8. ay lt Recycle used components Ja tot e Additional information wouFVsion 5 Version 1 5 Precaution Information Precaution RISK OF ELECTRIC SHOCK gt Use this unit only with the correct voltage as shown on the type label gt Do not expose the unit to extreme heat or moisture gt Do not expose the unit to water metallic objects or any flamma ble material gt Make sure that sufficient air circulation for cooling the unit is possible gt Do not use a damaged power cord power supply This may cause short circuits or electrical shocks gt To prevent danger do not modify the unit or operate it without a case gt Never use the unit without case gt Never touch the power supply or power cord with wet fingers gt f the unit is not used for a long time disconnect it from mains gt The power source eguipment has to be approved by CSA or UL in accordance to CSA 22 2 60950 or UL 1950 And it shall comply with all applicable local and national codes related to safety gt The Power over Ethernet power eguipment PoE PSE shall be classified as Limited Power Source LPS in accordance with IEC 60950 1 2001 RISK OF HURTING YOUR EYES gt Do not stare into laser beam of the remote control Laser class II Wavelength 650 nm The laser is conform to EN 60825 1 March 1997 The laser beam exits the remote control through the smaller left opening on the front
9. conds woLFV SION SCB 12 SCB 12 V1 30c Extra Menu Baud Rate 115200 Number of IR codes 4 Mounting Position REGULAR Pixel Calibration Noise Suppression ON Reset Admin Password Exit Speed of RS 232 port Factory setting is 115200 Possible settings e 9600 data transfer with 9600 baud s e 19200 data transfer with 19200 baud s e 38400 data transfer with 38400 baud s e 57600 data transfer with 57600 baud s e 115200 data transfer with 115200 baud s Number of possible IR codes Factory setting is 4 Function for authorized personnel only Do not change this setting Otherwise the supplied IR remote con trol may not support the IR code of the unit To rotate the image by 180 Factory setting is REGULAR Possible settings e REGULAR image will be output in normal orientation e FLIPPED image will be rotated by 180 The setting FLIPPED is useful when the camera is mounted up side down To restore defective pixels automatically To proceed the restoration cover the camera lens Function for authorized personnel only Version 1 5 52 wore Vsion OSD Noise Suppression L Reset Admin Password Exit Master Password Return unDurv ion SCB 12 To activate noise filter Factory setting is ON Possible settings e ON noise filter is switched on for images with little motion e OFF noise filter is switched off The setting improves
10. in a maximum frame rate of 15fps When switching on the Trigger mode in the on screen menu the SCB 12 freezes the current image The next image will be pro cessed when the SCB 12 receives a trigger pulse When the time between the trigger pulses is too short the mes sage Trigger Overrun will appear on the screen Decrease the trigger pulse frequency to rectify this Example with positive trigger edge ready for next trigger 1 30s 1 30s 1 30s lt gt lt t Exposure time a t frame rate L i Trigger in I P Hn 3 3 A Vss Exposure Image readout Version 1 5 28 wore Vision OSD General OSD On Screen Menu OSD Help For experienced users only 8 1 o For regular use of the SCB 12 it is not necessary to go into the units menu and change settings Inexperienced users should not make any adjustments there To enter the on screen menu press the MENU key 19 for one second Settings of the SCB 12 basic functions can be made here using the 4 SELECT keys 18 the numerical keys with red ar rows If more information for a function in the on screen menu is re quired set the cursor in the respective line and press the HELP key 25 on the remote control the numerical key Number 5 A detailed description of this function appears on the screen If you want to reset the selected item to the default setting press the HELP key 225 for 2 seconds By pres
11. Ga Preset Control Y Advanced Settings E Recall Default Settings TI Start Quick Setup Guide Ki Exit Changes Settings which affect brightness of picture e g Gain Shutter and Auto lris settings Changes settings which affect color reproduction of the camera Changes settings which affect output settings of the unit e g RGB and DVI resolution Changes settings which affect behavior of preset buttons Changes settings which need to be done only once e g Power Settings Ethernet Settings changing IR code etc Restore default menu settings and preset settings except items regarding output format resolution and refresh rate and connec tion settings i e network settings baud rate IR code The Quick Setup Guide will guide you through the most important settings like Ethernet Settings Exits the menu Version 1 5 30 wore vision OSD Gain Shutter Iris Priority Exposure Settings woveVsion SCB 12 EXPOSURE SETTINGS Gain AUTO LOW m Shutter AUTO Ky Iris Priority AUTO ES Image Brightness 40 IR Back Light Compensation OFF ta Extern Trigger OFF Return There are three auto settings available Additionally you can set the sensitivity of the camera from 0dB to 18 dB in 1dB steps Settings affect the depth of focus and noise level Factory setting is AUTO LOW Possible settings are AUTO LOW adjusts the lowest necessary gain level for best image quality automatically
12. IEEE802 3afTM 2003 with WolfVision interfacing board only Operating Temperature 0 C to 40 C Warranty 5 years Made in European Union EU wovrVsion 59 Version 1 5 Dimension Imensions D Technical Specification 12 2 1 2 D B ZE 9 4 3 8 110 57 H za Eo PA eos i xi gt de T pwa gt EI O Laud o 9 uOLFV SION 60 Version 1 5 Installation Eclipse 13 Installation 13 1 Eclipse The field of view is dependent on the zoom position of the optic horizontal 4 4 45 7 vertical 3 32 35 1 quie This part should not be covered optical axis wourVision 61 Version 1 5 Installation Cooling 13 2 13 2 1 13 2 2 Cooling WARNING Damaging the unit gt Mount heat sink For proper function some components of the SCB 12 require a heat sink In the drawing the relevant components are solid and hatched The use of a soft silicon gap pad is necessary to compensate the different height of the components Heat Sink Thermal resistance Rth 3 62 C W Gap Pad Technical data of the recommende
13. OSD will be shown as large window for better read ability The size of the OSD windows cannot be changed when one of the following resolutions is selected VGA XGA When the OSD window size is changed to large the position of the OSD window cannot be changed Horizontal position of OSD window on the screen Factory setting is 50 Possible settings e 0 to 100 in steps of 5 0 moves the window to the left side 100 to the right side Vertical position of OSD window on the screen Factory setting is 50 Possible settings e 0 to 100 in steps of 5 0 moves the windows to the top 100 to the bottom Position of status bar in relation to the OSD window Factory setting is BOTTOM Possible settings e BOTTOM the status bar will be displayed on the bottom of the OSD window e TOP the status bar will be displayed on the top of the OSD win dow Changes the color of the bar which indicates the current selected menu line Factory setting is WHITE Changes the color of the selected text in the bar Factory setting is BLACK Changes the color of the OSD text Factory setting is WHITE Changes the color of the text in the headline of the OSD Factory setting is Yellow Changes the color of the text in the status line Factory setting is WHITE Language Changes the language of the on screen menu Return Returns to previous menu page wore vision 41 Version 1 5 OSD Language Ok Canc
14. an image Press one of the MEMORY keys 26 for 2 seconds or more Recalling an image Press one of the MEMORY keys 26 guickly View Mode Splitscreen By pressing the ALL key 17 a split image with all 9 pictures of the memory can be displayed The memory can be erased or filled automatically in the on screen menu of the view mode ALL key 17 When choosing Auto Fill the SCB 12 stores every second a new image until all 9 memory locations are full With Erase All all 9 memory locations will be erased and shown with grey content The SCB 12 is equipped with a static memory to store the images permanently The functional settings of memory erasing can be changed in the on screen menu manually or automatically on every power on see page 29ff Recalled images from the memory can be digitally zoomed 5 7 Freeze To capture the currently displayed image into memory use the FREEZE key 16 The captured image is output wore vision 21 Version 1 5 Special functions Functions 9 8 for higher resolution 9 00 1 W WI Image Turn Mode Picking up a complete vertical portrait document or A4 page has always been a critical issue because the image was always picked up in a horizontal landscape format The camera could only use 50 of its pixels to pick up a vertical portrait page WoliVision s Image turn mode solves this prob lem Just place your document or other vertical obje
15. data of the laser diode A 635 680nm P lt 1mW lt 2mrad Approval marks on the unit As the SCB 12 is a camera module for OEM customers it has no FCC or CE approvals The customer is responsible for FCC CE and other necessary ap provals wovrVsion 7 Version 1 5 Content of packaging Contents of packaging 2 1 2 2 SCB 12 standard set Following components are included in the carton box SCB 12 Guick manual all signals will be provided through JST and Molex connectors SCB 12 Test set Following accessories are included with the SCB 12 Test set Interfacing board for SCB 12 Lockable power connector BNC RCA adapter for trigger input IR remote control with laser pointer External IR receiver with 10m cable and status LED Power supply Power cord User manual CD Rom VGA cable D sub 15pin HD USB cable LAN cable PoE pomer injector Please retain the original packaging for later transports of the SCB 12 and accessories Version 1 5 8 wore vision Camera Features 3 Features The SCB 12 is an ultra compact color camera module with SXGA resolution 1280x960 and 30 frames per second With the integrated scan converter the camera is able to output different resolutions and refresh rates for optimum picture reproduction The SCB 12 has a high quality lens with 12x optical zoom and 4x digital zoom The camera module has an auto focus and manual focu
16. key 16 for 2 seconds recalls preset 1 For storing a preset adjust any function as required and then press any one of the PRESET keys on the remote control for 2 seconds or more An on screen message will inform you when the preset is stored When presets are stored as mentioned above all current settings Such as zoom focus iris etc are stored The user can also assign specific functions such as Negative Negative Blue BlackWhite etc to a PRESET key in the on screen menu of the SCB 12 see page 29ff wovrVsion 19 Version 1 5 Basic functions Functions 5 5 5 5 1 White Too Bright White Too Dark White Out of Range White Balance The correct white balance adjustment is important for exact color reproduction Auto Tracking is the default white balance setting when the SCB 12 is shipped This means that the white balance is continu ously adjusted automatically For an exact white balance 10 of the recorded image should be white measurement area is in the center of the image For a precisely fixed white balance adjustment use the One Push white balance This can be done by completely zooming in on a white surface and pressing the WHITE key 15 When the white balance is stored an on screen message appears Setting a One Push white balance switches off the Auto Tracking mode when the unit is switched off and on again the Auto Tracking mode will be reactivated W
17. motion WolfVision s Connectivity Software can store AVI files and includes a video cap ture driver You can view and save the live image from the SCB 12 on your computer in almost every modern video editing software Please download the latest version of the WolfVision Connectivity Software from www wolfvision com support Pictures which are stored with the WolfVision Connectivity Soft ware includes EXIF data if file format JPG or TIFF is used Includ ed data are Manufacturer WolfVision Model inclusive serial number i e SCB 12 00103701 Firmware version i e V2 00a Date and time of create i e 2011 09 18 11 06 29 yyyy mm dd hh mm ss On Microsoft Windows computers install the driver before connect ing the SCB 12 to the computer Otherwise the driver has to install manually in the system preferences of Microsoft Windows Connectivity Software version 1 7 or higher will be needed to work with camera firmware v1 20b and higher wourVision 25 Version 1 5 Connections 7 7 10BASE T 100Base TX quie 3o Ethernet LAN Port The LAN port 7 makes the SCB 12 a part of the internal com puter network and it can be used for communication over the Inter net if it is assigned an official WAN IP address Administrators of a larger number of Visualizers can use the LAN port to control support and update all of their units from their local desktop PC The list of ap
18. quie quie Resolution Picture refresh rate Pixel format vertical frequency 1080p HD HDTV 16 9 50Hz 1920x1080 60Hz 720p HD HDTV 16 9 50 Hz 1280 x 720 60 Hz WSXGA 1680x1050 16 10 60Hz WXGA 1440 x 900 16 10 60 Hz WXGA 1360 x 768 16 9 60 Hz WXGA i 1280 x 800 16 10 60 Hz SXGA 1400 x 1050 43 60 Hz SXGA 5 4 60 Hz 1280 x 1024 75 Hz SXGA 4 3 60 Hz 1280 x 960 85 Hz XGA 4 3 60 Hz 1024 x 768 75 Hz SVGA 800 x 600 4 3 60 Hz VGA 640x480 id 60Hz The Auto resolution function is activated by default In this mode the SCB 12 continuously checks which devices are connected to the RGB 8 and DVI output 10 and automatically sets the op timal output mode for each connected device separately Please note that the SCB 12 cannot check the possible resolution if the connected units or the cables are not Plug and Play compatible If the SCB 12 cannot detect the resolution of the connected device the output is set to the default of SXGA 1280x960 60Hz Cables with plug and play compatibility must have a 15 pin plug on both ends with all pins connected pin 9 is not used If you cannot use the Auto resolution function you can select the output mode manually in the on screen menu of the SCB12 see page 29ff WoLFV SION 54 Version 1 5 Resolution and refresh rate quie quie quie
19. the IP address of the SCB 12 Returns to previous menu page If the stream applet needs a long time to start please check Java network settings and select direct connection wourVision 45 Version 1 5 OSD Admin Password Guest Password Ethernet Mode Security Settings woLFV SioN SCB 12 SECURITY SETTINGS 3 Admin Password rss a Guest Password Password Pi Ethernet Mode FW CTRL IMG si Return To prevent un authorized access Admin password has to be entered before any changes are possi ble Factory setting is Password e Possible characters are 0 9 a z and A Z e 10 digits Write down the passwords and keep it securely If you forgot the password or lost it the access through the Ethernet LAN port may be denied Contact your WolfVision dealer in such case www wolfvision com To prevent un authorized access Admin password has to be entered before any changes are possi ble Factory setting is Password e Possible characters are 0 9 a z and A Z e 10 digits Write down the passwords and keep it securely If you forgot the password or lost it the access through the Ethernet LAN port may be denied Contact your WolfVision dealer in such case www wolfvision com To change the behavior of accessibility to the unit via the network Factory setting is FW CTRL IMG Possible settings are e FW CTRL IMG Ethernet connection can be used un restricted e AUTH Eth
20. the SCB 12 e OFF the unit will start without showing the logo Defines the behavior of the unit when connecting the power supply Factory setting is POWER ON Possible settings e POWER ON the unit will be switched on when connecting the power supply e STAND BY the unit will stay in stand by Energy saving function when the unit is not in use for the specified time it will switch automatically to stand by mode Factory setting is OFF Possible settings e OFF the unit stays on e 30min stand by mode after 30min of non use e 1h stand by mode after 1h of non use e 2h stand by mode after 2h of non use e 3h stand by mode after 3h of non use e 4h stand by mode after 4h of non use Returns to previous menu page Version 1 5 38 wore vision OSD IR Code i Erase Memory L Image Turn Rotation Miscellaneous Settings woveVsion SCB 12 MISCELLANEOUS SETTINGS IR Code A x Erase Memory MANUALLY a Image Turn Rotation CYCLE Qui Digital Zoom 2X n Dig Zoom Warning STOP Ki Return IR remote code Helpful when there are IR interferences in the same room as the SCB 12 Factory setting is A Possible settings e A IR code A e B IR code B e C IR code C e D IR code D The IR remote control has to be set to the same IR code as the unit to function correctly see page 56 For activating the new code select the line Activate new IR code here Changes
21. will decide whether the faulty product will be replaced or repaired Not covered by warranty e Damages inflicted locally e g installation errors fire lightning strikes etc e Units where the serial number is missing or was manipulated e Damages due to disregard of the user manual e g connecting the unit with the incorrect mains voltage or for damages caused by careless handling or improper use e Defects resulting from repairs adaptations or adjustments which have been made to the unit without WolfVision s prior consent e Old or worn out parts e g bulbs broken parts made of glass or scratched mirrors e Damages incurred by the system into which the unit has been integrated e Damages during transport due to improper packaging the origi nal packaging should be kept or can be ordered from WolfVision on loan Version 1 5 70 wore vision Warranty 16 4 Transit damage or loss All shipments are insured by WolfVision up to the first consignee in most cases the Dealer Distributor Reimbursement can only be claimed if the receiver indicated on the packing list complies with the following instructions e All shipments should be inspected upon arrival Any apparent damage to the packaging and or product or loss noticeable upon delivery must be noted and marked appropriately on all copies of the carriers waybill It is of utmost importance that the driver signs all copies in acknowledgement e The car
22. you can activate the on screen help by pressing the HELP key Pressing this key for 2 seconds resets the selected menu item see page 29ff MEMORY keys 1 9 For saving and recalling pictures see page 21 POWER key Switches the unit on and off When switching the unit on the SCB 12 automatically runs the power on preset wourVision 17 Version 1 5 Basic functions Functions FUNCTIONS 9 1 9 1 1 9 2 3o quie 5 3 Cd quie The SCB 12 can be controlled through a key matrix IR remote control IR receiver will be required via Ethernet LAN USB or RS 232 Zoom The SCB 12 uses a 12x zoom lens f 5 8 to 69 6 mm F 2 8 to 3 0 Digital Zoom The digital zoom is automatically switched on at the tele end of 12x optical zoom range with progressive effect from 1 to 4 giving a to tal maximum of 48x zoom ratio Digital zoom increases the picture element size and reduces the resolution The default setting displays a message on screen when you are in the digital zoom mode Still pictures in the memory can also be digitally zoomed You can change the behavior of the SCB 12 in the digital zoom mode in the on screen menu see page 29ff Auto lris Manual lris The SCB 12 is equipped with an auto iris function This means that the brightness of the camera image adjusts automatically When using the IRIS keys 24 the auto iris function is switche
23. M46 x 0 75 Weight 94g Details at www wolfvision com Working surface The optional inclined working surface for the SCB 12 has a special crystalline white surface for transparencies 435 x 325 x 40 10 mm 17 13 x 12 8 x 1 57 0 39 Details at www wolfvision com Version 1 5 66 wouFVsion Troubleshooting 15 Troubleshooting 15 1 Check Description Power check connect the unit to is the power LED red illumi mains check main nated switch depending on power set tings in the on screen menu depends on customer instal lation switch on the unit is power LED green illumi with the power key nated may unit starts up automati cally depends on power set tings in the on screen menu depends on customer installation Image check connect display does the unit outputs an im ALL OUT device age PUTS place color test color test chart is showed chart correctly is brightness ok with auto iris place test chart is the image focused letters lines switch on auto focus Key check press all keys on all keys are working well the unit depends on customer instal Lu Afation press all keys on all keys are working well the remote control depends on customer instal lation 15 2 Power depends on customer installation POSSIBLE CAUSE SOLUTION power indica no mains power check mains and power cord tion LED is cord missing or not illuminated dam
24. N COM MEER 19 5 5 White Balano EE 20 5 6 Image Memory for 9 images oooooon ono HERE 21 5 7 dy r rp 21 9 8 Image TUM MOUS EE 22 6 Working with ERC E 23 7 GONNSCU IE tin kat n O A ren 24 7 1 pu BEE EE E 24 7 2 PGB uu S SS a po n kika aS E ko S AM N 24 7 3 Power PIWO ia 24 7 4 RS 292 5 Mu oe x L ao ce eee kle S ca ag pk occas a a NG kep e Cu 24 7 5 External Infrared IR Sensor oooonoon oo o 25 7 6 BE E E E EE EN aha 25 7 7 Ethernet LAN Pont 26 7 8 ee OL ky 28 8 OSD On Screen Menu OSD Help U u u u u uu uu u uu u u u 29 8 1 Reset On Screen Menu Settings o nennen 29 8 2 Str cture and functions Of OSD EE 30 9 Resolution and refresh rate oorornnnnnn HEHE uuu HRE 54 10 MAINTENANCE 56 10 1 dun Eua e E 56 10 2 IR Infrared Remote Control 56 10 3 Different ID Code 56 10 4 I a kw in kaye aghast 57 10 5 TRANS 916 arz ui o MER 57 11 Technical SpecifICations 45 45 u u A Hala 58 12 DIL Dn 60 13 Installation pm as ssa zas 61 13 1 ele 61 13 2 Cooling n Se oa ao no ME 62 13 3 Matix for cae u an deye u s
25. RISK OF DAMAGING THE UNIT gt Protect the unit from excessive shocks gt Do not expose the unit to extreme heat or moisture gt Do not expose the unit to water metallic objects or any flamma ble material gt Make sure that sufficient air circulation for cooling the unit is possible gt If there is any abnormality abnormal noise smell smoke etc disconnect the unit from mains immediately and contact your WolfVision dealer gt Avoid installing the unit in environments where there is radiation gt Avoid installing the unit in locations exposed to strong magnetic fields or electrical currents This could cause monitor image distortion or damage to the CCD camera gt Never use strong cleaning agents Version 1 5 6 wore vision Information Labels and Approvals IEC 60825 1 2007 635 680nm P lt imW CLASS 2 LASER PRODUCT PRODUIT LASER DE CLASSE 2 LASERPRODUKT DER KLASSE 2 Daags CAUTION LASER LIGHT DO NOT STARE INTO BEAM LUMIERE LASER NE PAS REGARDER LE RAYON FIXEMENT LASERSTRAHLEN NICHT IN DEN LASERSTRAHL BLICKEN L Y AS ETLE DE ASILTE 123456 1 2 Labels on the remote control optional Laser Information FDA accession number 9912688 00 This laser device complies with the restriction 21 CFR 1040 10 und 1040 11 The remote control is included in the SCB 12 Test set This label will be found on the underneath of the remote control Technical
26. UP GUIDE Adjust language used in the OSD menu P Setup Language Cc Next Select Setup Language to select the desired language limited different languages are available see page 42 Select Next to skip this point wouFVsion SCB 12 QUICK SETUP GUIDE Adjust Ethernet settings to access your local area network LAN or your wide area network WAN st Setup Ethernet Settings Next Select Setup Ethernet Settings to perform Ethernet adjustment see page 43 Select Next to skip this point wnLevision SCB 12 QUICK SETUP GUIDE Adjust date time timezone dateformat and optional timeserver v Setup Time Settings E a Next Select Setup Time Settings to adjust time and date see page 48 Select Next to skip this point Version 1 5 50 wore vision OSD wouFVsion SCB 12 QUICK SETUP GUIDE You have successfully finished the Quick Setup Guide Go to the OSD menu if you want to start over Finish and Exit Select Finish and Exit to complete the Quick Setup Guide To abort press the MENU key and the Quick Setup Guide will ap pear on next hard power on again woLFV SiOn 51 Version 1 5 OSD 8 2 2 Baud Rate Number of IR Codes L Mounting Position Pixel Calibration Extra Menu Enter the extra menu by keeping pressed the MENU key for 4 se
27. aged faulty power supply change power supply power indica unit is in stand by switch on the unit by pressing tion LED is mode the POWER key Power indi red illuminat cation LED has to be green ed 15 3 IR remote control optional no function at all laser pointer POSSIBLE CAUSE batteries SOLUTION check batteries change it check polarity no response of the unit laser pointer is working IR receiver check IR code change it if necessary check IR receiver may be it is covered Version 1 5 67 wourVsion Troubleshooting 15 4 Image SYMPTOM POSSIBLE CAUSE SOLUTION no image unit is in stand by switch on the unit by press mode ing the POWER key Power indication LED has to be green depends on customer instal lation bad wiring to the check connected cable display device display device check display device settings and connections wrong resolution check settings may connect and or refresh rate another display or check settings via Ethernet LAN or RS 232 see page 54 Iris completely press IRIS OPEN key or closed press a ZOOM key to acti vate the AUTO IRIS function Bad image wrong menu ad check settings like resolution quality justments gain shutter detail reset complete on screen menu wrong display ad check adjustments may use justments color bar chart Bright spots front lens dirty clean the len
28. cht Favoriten Extras a Ouma x 2 Ch suchen yere xd m JM ay Adresse E http www wolfvision com wolf Eye_020 html v E wechseln zu Links Move the lamp with your mouse and see the problems of each light position YH Ceiling VINI x JB X Problems of the lis sition Reflections in the picture This problem can be solved ifyou tilt the working surface slightly Internet wWoLFV SiON 65 Version 1 5 Accessories Optional 14 OPTIONAL WolfVision Accessories 14 1 14 3 External WolfVision Lightbox A optional lightbox bottom light is recommended for dark trans parent material such as x rays or for very small transparent materi al such as slides When a lightbox is used the room light should be dimmed or switched off When light conditions change a white balance adjustment should be performed to compensate the varying color temperatures of different light sources see page 20 WolfVision offers lightboxes for x rays slides and transparencies in two sizes LB 38 430 x 359 mm 16 9 x 14 1 LB 9 300 x 210 mm 11 8 x 8 3 Details at www wolfvision com Close Up Lens The optional Close Up Lens can be used to focus on objects at a close distance to the SCB 12 Technical data High resolution achromatic lens Focus range 310 460mm Focal distance fz477mm Lens diameter 50mm Attachment thread
29. ct on the working surface horizontally Zoom in on it completely so that approx 90 of the pixels of the built in camera are used to pick up the docu ment Press the IMAGE TURN key 22 The SCB 12 turns the picture electronically at an angle at 90 and outputs it correctly with a much higher resolution than in normal mode The left and right margins are blackened out Normal mode The graphic on the left illustrates the picked up text The graphic on the left illustrates the reproduced text on the display device Only 50 of the pixels are used to pick up the document Image Turn mode The graphic on the left illustrates the picked up text The graphic on the left illustrates the reproduced text on the display device 90 of the pixels are used to pick up the document The output image will be electronically turned By using more pixels for picking up the image sharpness will be increased Version 1 5 22 wouFVsion Work with tne SCB 12 Working with the SCB 12 Power on Preset e Connect all necessary cables to the SCB 12 e Set the output resolution and refresh rate to the right setting depends on the connected display device see page 29ff IMPORTANT Note the hints in the manual of the connected display device regarding resolution and refresh rate e Switch on tne SCB 12 by pressing the power key or sending a power on command e By default the SCB 12 performs the power on preset automatic setting t
30. ctly streamed images the RGB DVI output has to be set to the same image format 4 3 or widescreen as the multicast streaming format see page 45 In case the connected display is not capable to show an image with the selected resolution or refresh rate change the setting with following shortcuts Change resolution refresh rate upwards press simultaneously both FOCUS keys on the unit Z23 and the Number 2 key up arrow 18 on the remote control Set resolution refresh rate to AUTO press simultaneously both FOCUS keys on the unit Z23 and the Number 5 key help 25 on the remote control Change resolution refresh rate downwards press simultaneously both FOCUS keys on the unit Z23 and the Number 8 key down arrow 18 on the remote control If no remote control is available connect another display or change the resolution refresh rate by sending command codes via RS 232 or USB Ethernet LAN wa rev sion 55 Version 1 5 Maintenance 10 MAINTENANCE 10 1 symbolic view Sy e 10 3 Firmware Upgrades The software firmware of the SCB 12 including the on screen HELP can easily be upgraded to the latest version The firmware update can be done via USB Ethernet LAN or RS232 Firmware update files can be downloaded for free at www wolfvision com support Updates via USB and Ethernet LAN can be made with the WolfVision Connectivity Software version 1 5 and h
31. d gap pad i e GAP Pad Ultra Soft from Bergquistcompany www bergquistcompany com GPVOUS 0 08 00 00 NA Property Value Test method Hardness 5Shore ASTMD2240 Dielectric breakdown gt 6000 VAC ASTMD149 Dielectric constant 1000Hz 5 5 ASTM D150 Volume resistively Ohm 10 ASTM D257 meter Thermal conductivity 1 0 W m K ASTM D5470 yellow foil 57 2 3 8 51 2 I I l 2 6 8 1 8 Version 1 5 62 uOLFV SION Matrix for Key panel Installation 13 3 Matrix for key panel The drawing shows the matrix of the key panel for connector 1 see page 12 pin11 pin10 pin9 pin8 pin1 C4 C3 C2 C1 GND O O O O O AF LED EN B pin2 Iris Close Memory 7 Memory 4 Memory 1 AF LED x x x x pin3 Focus Near Memory 8 Memory 5 Memory 2 R1 NA lt gt x x X ani Focus Far Memory 9 Memory 6 Memory 3 R2 Zx L XS x x x pin5 Zoom Wide White Balance AF Zoom Tele R3 Ku Ne se s x x x x pin6 Iris Open Power Menu Freeze R4 n LO J ed ees R5 Cx Columns Rx Rows wourvision 63 Version 1 5 Position of Light Installation 13 4 13 4 1 Recommended Positioning of Light General Please consider light positioning for the SCB 12 carefully Mount ing the light too close to the unit will cause re
32. d off In this mode the iris can be adjusted manually When using the ZOOM keys 12 the auto iris is switched on again The auto iris also controls the Auto Gain and Auto Shutter to ex tend the iris range The auto iris priority can be switched off in the on screen menu Auto iris priority means when pressing the ZOOM keys the auto iris switches on The overall brightness level can be set lower or higher in the on screen menu with Image Brightness see page 29ff The optimal setting depends on the connected display device Focus Autofocus The minimum focus distance MOD is below 50mm at optical wide end and below 500mm at optical tele end and is independent of digital zoom If shorter distances are necessary a high quality close up lens is available see optional accessories Please note that objects with very low contrast e g a blank sheet of paper are difficult to focus If the autofocus does not work just move the object slightly For special applications the autofocus can also be switched off using the on off switch 14 The autofocus is also switched off when the manual FOCUS keys 23 are used Version 1 5 18 wouFVsion Functions Basic functions 9 4 quie o Preset Function The SCB 12 offers the possibility to store the current settings as a preset and recall them by just pressing the respective PRESET key 416 on the remote control Pressing the FREEZE
33. date setting will be lost after removing of mains no RTC Shows current time The time can be changed by selecting each digit Manual time setting will be lost after removing of mains no RTC Version 1 5 48 wore vision OSD Return quie Returns to previous menu page Recall Default Settings waLev sion SCB 12 AUTO PRESET Are you sure Ok Bi Cancel Select YES to reset all Settings to factory default Settings regard ing output and communication are not affected like resolution IR code baudrate IP address For resetting just the selected item in the OSD keep the MEMORY 5 key pressed for 4 seconds In case the connected display does not show an image set the unit back to the factory default by keeping pressed simultaneously both FOCUS keys on the unit 23 and the Number 4 key back arrow 18 on the remote control To change the resolution without entering the on screen menu just keeping pressed simultaneously both FOCUS keys on the unit 23 and select the desired setting e MEMORY 5 on the remote control Resolution AUTO e MEMORY 2 on the remote control Resolution UP when select ed AUTO before the next setting is VGA 60Hz e MEMORY 8 on the remote control Resolution DOWN woLFV SiOn 49 Version 1 5 OSD Start Guick Setup Guide After first power on the Quick Setup Guide will be started automat ically wote Vsion SCB 12 QUICK SET
34. e vision applications For example a light barrier can simultaneously send out a trigger pulse to the SCB 12 and to a harddisc recorder when somebody enters a room Most normal recording devices can not start record ing within a fraction of a second If such a camera outputs a live image either a later image which does not show the exact situation is recorded or the recorder saves a stream of images and there fore reguires a large amount of data space NORMAL MODE Free Running In normal mode Trigger is de activated by default the camera generates live images with a frame rate of 30 fps The duration of exposure can be changed in the on screen menu with the shutter setting The sampling time is controlled by the camera electronics and can not be changed TRIGGER MODE The SCB 12 offers a trigger input to determine the moment of im age readout When the TRIGGER function is activated the sampling time is controlled by receiving trigger pulses pulse with 3 3 to 40Vss pos itive or negative edge selectable in the on screen menu see page 29ff The image is processed 1 30s after the camera receives the trigger pulse The exposure time is variable and determined by the shutter time However the end of exposure is always 1 30s after the trigger pulse The start of exposure is also determined by the shutter time Shutter is adjustable in the on screen menu The maximum trigger frequency is 15Hz 2x 1 30s This will result
35. eans without prior written permission from WolfVision Except documentation kept by the purchaser for backup purposes In the interest of continuing product improvement WolfVision re serves the right to change product specifications without notice Information in this document may change without notice Disclaimer WolfVision shall not be liable for technical or editorial errors or omissions The units are MADE IN EU AUSTRIA Printed in Austria October 2011 About this user manual This user manual explains the SCB 12 and all of its contents Please keep this user manual for later reading When selling the SCB 12 please give this user manual to the next owner Version 1 5 4 wore vision Information Marks in this manual Symbols in this manual Position numbers are written in bold italic characters and marked with the symbol i e 1 for connections Safety information is marked with corresponding pictographs and the instruction seguences are marked with the symbol gt The word Danger indicates possible serious personal injury The word Warning indicates possible personal injury and or seri ous equipment damage The word Attention indicates possible personal injury and or equipment damage High voltage Risk of electric shock Hot surface Risk of get burnt Laser beam Risk of injury Risk of possible material damages P P P P Advise for disconnecting the unit from mains
36. eck on screen menu set tings Color Settings flickering image room lights are fluorescent lamps check shutter settings in the on screen menu Exposure Settings low refresh rate with CRT display device increase refresh rate wrong display de check display settings vice settings bad wiring to the check wiring display device 15 5 Connections POSSIBLE CAUSE connect computer to the unit and start USB software SOLUTION check wiring to the computer check driver installation check USB port of the com puter LAN Ether net port connect computer to the unit start Internet browser and input the IP address of the unit check wiring to the computer check kind of wiring crossed or straight check Ethernet Settings of the unit check Ethernet port of the computer check security settings connect computer to the unit and start Hyper Terminal or similar and press v to check com munication check wiring Null modem check serial port settings in the on screen extra menu check serial port of the com puter wourVision 69 Version 1 5 Warranty 16 Warranty 16 1 16 2 16 3 General WolfVision guarantees their products to be free from defective ma terials and faulty workmanship for a period of 36 monihs from the date of dispatch date of invoice for units shipped after the 1st of January 2005 or late
37. ed Settings woveVsion SCB 12 ADVANCED SETTINGS Power Settings Miscellaneous Settings OSD Settings ss Ethernet Settings 8 Device Info EC Date Time Settings Ki Return Changes settings which affect behavior of the unit when switched on Changes settings which affect OSD IR code digital zoom etc Changes settings which affect the display of OSD like color and position Adjusts settings of LAN interface like IP address shows MAC ad dress etc Shows details of the SCB 12 like serial number and version num ber of the installed firmware Adjusts date and time Returns to previous menu page wovrVsion 37 Version 1 5 OSD Power On Preset Store Power On Preset Display Logo Mains On Auto Power Off Return Power Settings jP a 6 SCB 12 POWER SETTINGS Power On Preset ON Store Power On Preset Display Logo ON Mains On POWER ON Zz Auto Power Off OFF kl Return Factory setting is ON Possible settings e ON Power On preset will be recalled when switching the unit on e OFF unit will stay in last zoom position Perform all desired adjustments like zoom image turn etc and select this line to store the Power On preset To get factory Power On Preset recall default preset settings in the Preset Control menu Factory setting is ON Possible settings e ON WolfVision Logo WolfVision SCB 12 will be displayed shortly when switching on
38. ek hn 63 13 4 Recommended Positioning of Light enne 64 14 OPTIONAL WolfVision Accessories oretroron on RE RE uu u uu u 66 Version 1 5 2 wouFVsion Table of Contents 14 1 14 2 14 3 15 15 1 15 2 15 3 15 4 15 5 16 16 1 16 2 16 3 16 4 17 17 1 17 2 External WolfVision Lightbox eene enne nnne nnne 66 Glose Up Lens s iit a Ugo NUR UDINE FM AMA E i eI M MEE 66 WOFKING SUMACG Sito ke e ve look 66 Troubleshooting EE 67 Check nu e E k HU RR E re agate 67 Power depends on customer installation u 67 IR remote control ele re II 67 wt Le zu sum EE 68 GoninectionS 1s1 5 E M 69 Warranty 70 Cc EP 70 pe d onatrival DOA rH 70 Noticovered by Warranty iini Ert EHE ER q aba ER RYE 70 Transit damage Tel TEE 71 Disposal of old WolfVision units J nn U U u u uu uu uu uu uu 72 In the European BT P 72 Outside of the European Union o on 72 wore vision 3 Version 1 5 Copyright Information Copyright Information Date of printing Copyright by WolfVision All rights reserved WolfVision Wofu Vision and iX fi XH iK are registered trade marks of WolfVision Holding AG Austria No part of this document may be copied reproduced or transmit ted by any m
39. el Language woveVsion SCB 12 CHANGE LANGUAGE Language ENGLISH o eo Cancel Changes language of the on screen menu Factory setting is ENGLISH Possible settings e ENGLISH e DEUTSCH e T RKCE Change of the language will restart the on screen menu Confirms the selected language and returns to previous page Returns to previous menu page without any change Version 1 5 42 wourVision OSD DHCP Ethernet Settings wouFVSion SCB 12 ETHERNET SETTINGS DHCP ON amp IP Address FROM DHCP SERVER Subnet Mask FROM DHCP SERVER a Gateway IP FROM DHCP SERVER B Streaming Settings a Security Settings Ki Return IP Address 192 168 0 Subnet Mask 255 255 255 A Gateway IP 192 168 0 1 If DHCP server is available set it to ON Factory setting is ON Possible settings are e ON IP Address Subnet Mask and Gateway IP will be set auto matically e OFF IP Address Subnet Mask and Gateway IP have to be set manually Ask your network administrator for more details regarding the in stalled network When no DHCP server is available the respective addresses are marked with 7 99 IP Address De activate DHCP and set the IP Address manually Factory setting is 10 0 0 160 Ask your network administrator for more details regarding the in t stalled network Subnet Mask De activate DHCP and set
40. epends on the recorded image and back light Factory setting is OFF Possible settings are e OFF no back light compensation e MED compensation of back light up to 50 of the image area e HIGH compensation of back light up to 80 of the image area Trigger function of the SCB 12 see page 28 Factory setting is OFF Possible settings are e ON Trigger function is activated e OFF Trigger function is de activated Available with activated Trigger function only Factory setting is POS Possible settings are e POS triggering to the positive edge of trigger pulse e NEG triggering to the negative edge of trigger pulse Returns to previous menu page 205 Westwood Ave Long Branch NJ 07740 Phone 866 94 BOARDS 26273 732 222 1511 Fax 732 222 7088 E mail sales touchboards com Version 1 5 32 wore vision OSD White Balance quie Color Mode Jo Color Settings wouFVsion SCB 12 COLOR SETTINGS eo White Balance AUTO TRACKING a Color Mode PRESENTATION Mode Gamma 1 Saturation 105 Pos Neg Blue POSITIVE Ki Return Factory setting is AUTO TRACKING Possible settings are e AUTO TRACKING the white balance will be tracked permanent ly to the picked up object document This can lead to wrong col ors on some critical objects e ONE PUSH press the white key to perform a one push white balance e MANUAL manual adjustment of red and blue values there
41. ernet connection depending on authentication admin has full access FW CTRL IMG guest has restricted access IMG e OFF firmware updates controls and image transfers are prohib ited e IMG ONLY firmware updates and controls are prohibited Ethernet connection can be used for image transfers only e CTRL ONLY firmware updates and image transfers are prohib ited Ethernet connection can be used for control purposes only e CTRL IMG firmware updates are prohibited Ethernet connec tion can be used for controls and image transfers only e FW ONLY controls and image transfers are prohibited Ethernet connection can be used for firmware updates only Version 1 5 46 wore vision OSD Return Serial Number Version Build Number Return e FW IMG controls are prohibited Ethernet connection can be used for firmware updates and image transfers only e FW CTRL image transfers are prohibited Ethernet connection can be used for firmware updates and control purposes only Ask your network administrator for more details regarding the in stalled network Firmware updates requires WolfVision connectivity software Returns to previous menu page Device Info This fields are not changeable wourvision SCB 12 DEVICE INFO Serial Number 1031707 Version V2 00d Build Number 20111012083940 kl Return Shows the serial number of this SCB 12 Shows the version number of the installed
42. f separately in accordance with the Eu ropean Union s directive on waste electrical and electronic eguip ment and local regulations This also applies to SCB 12 electrical accessories e g remote control power supply and signal cables Dispose of the SCB 12 in accordance with local government regu lations contact your local WolfVision dealer or if applicable in accordance with a WolfVision agreement Outside of the European Union Contact your responsible local authorities for information about the correct disposal of electrical and electronic devices wouFVsion 72 Version 1 5 WDLFV SION 205 Westwood Ave Long Branch NJ 07740 Phone 866 954 BOARDS 26273 732 222 1511 Fax 732 222 7088 E mail sales touchboards com
43. firmware Shows date time stamp of the installed firmware built number Returns to previous menu page wa rev sion 47 Version 1 5 OSD Time Source L Timezone L Date Format Date Date Time Settings wouFVsion SCB 12 DATE TIME SETTINGS oP Time Source INTERNAL op Timezone UTC au Date Format DDMMYYYY 24H Fa Date FROM DHCP SERVER v Time Return Select if time is in free running mode or synchronized with a time server Daylight saving time standard time will be changed auto matically by selected timezone Factory setting is INTERNAL Possible settings are e INTERNAL internal clock are used time and date will be lost by power interruption e EXTERNAL enter valid IP address of a time server Ask your network administrator for a valid time server IP address Select local timezone for correct time calculation Daylight saving time standard time will be changed automatically by selected time zone Factory setting is UTC Possible settings are from EUROPE LONDON to Afri ca Casablanca Ask your network administrator for more details regarding the in stalled network Select the preferred time format Factory setting is DDMMYYYY 24H Possible settings are e DDMMYYYY 24H i e 22 05 2011 19 53 e MMDDYYYY 12H i e 05 22 2011 07 53 PM Shows the current date The date can be changed by selecting each digit Manual
44. flections mounting it too far away will cause shadows The illustration below shows the recommended position of lighting for the SCB 12 The distance from the center of the unit to the cen ter of the light should be identical to the MAXIMUM image size e g vertical image size Example If the camera is mounted 1400mm above the working surface then the maximum vertical image size is 893mm see length value in table on page 9 or use the calculation program at www wolfvision com wolf indexdistance html This means that 893mm is also the recommended distance from the center of the unit to the center of the light We recommend mounting the light like the position shown below because here shadows are not too disturbing when pointing at cer tain details on a document Due to the automatic white balance of the unit it is possible to use any type of light WolfVision recommends a diffused light with more than 300 Lux and a homogeneity of less than 15 on the working surface Ceiling where the light should be Sa mounted Version 1 5 64 wouFVsion Installation Position of Light 13 4 2 Flash Animation A very easy method to find the ideal light position for the SCB 12 is the dedicated flash animation program on WolfVision s homepage www wolfvision com wolf Eye 020 html A WolfVision Visualizer Microsoft Internet Explorer bereitgestellt von WolfVision Austria EIS Datei Bearbeiten Ansi
45. ge 29ff 19 MENU key Pressing this key for 1 second activates the on screen menu see page 29ff Version 1 5 16 wovrvision Test set IR Remote Control 20 21 22 23 24 25 26 27 LASER indication LED IR Code indication LED For indicating the LASER status of the unit red on dark off When changing the IR code on the IR remote control the LED flashes in accordance with the selected IR code see page 56 LASER POINTER key Important Do not stare directly into the beam This is hazardous for your eyes IMAGE TURN key For picking up vertical portrait pages with higher resolution see page 22 Manual FOCUS keys For focusing the picture When the Manual FOCUS keys are pressed the SCB 12 switches off the autofocus function Using the AF key switch es the autofocus function on again Manual IRIS keys brightness adjustment When the IRIS keys are pressed the SCB 12 switches off the auto iris function The next time the ZOOM keys are used the auto iris is switched on again For specialists The auto iris priority can be switched off in the on screen menu Auto iris priority means when pressing the ZOOM keys the auto iris switches on The overall brightness level can be set lower or higher in the on screen menu with Image Brightness see page 29ff The optimal setting depends on the connected display device HELP RESET key for on screen menu While you are in the on screen menu
46. hen the lighting conditions change e g light box sunlight or different room light the white balance should be re adjusted For specialists The SCB 12 can be switched between Auto Track ing One Push and Manual white balance mode in the on screen menu see page 29ff If you work with negative transparencies and a light box use a blank black in the image piece of the negative film for white bal ance adjustment White balance adjustment errors If the white balance adjustment is not successful an error message appears on the screen If this happens take the necessary measures The video signal level is too high Take one or more of the follow ing measures and then perform the OWB again e Remove any brightly illuminated objects e Decrease the illumination e Close the iris opening e Decrease the video gain The video signal level is too low Take one or more of the following measures and then perform the OWB again e Increase the illumination e Widen the iris opening e Increase the video gain Place a white sheet of paper and perform the OWB again Version 1 5 20 wore vision Functions Special functions 9 6 Edo Example of a splitscreen L quie quie Ge Image Memory for 9 images The SCB 12 has an image memory from which a stored image can be output as a still image You can store up to 9 images in the memory Code Storing
47. icast Ask your network administrator for more details regarding the al lowed network traffic Some Streaming players cannot listen on demand and needs the settings CONTINUOUS for proper work Multicast one stream with multiple listening devices Unicast one stream each listening device Version 1 5 44 wore vision OSD Streaming Format Frame Rate Ge quie quie Return L Distributed resolution Factory setting is VGA Possible settings are e VGA 288p VGA e XGA 576p XGA e SXGA 720p WXGA Ask your network administrator for more details regarding the al lowed network traffic The streaming ratio will be changed automatically to the same image ratio as the selected resolution in the Output Settings 4 3 16 9 or 16 10 see page 54 Distributed frame rate Factory setting is MEDIUM Possible settings are e LOW 1fps at VGA resolution e MEDIUM 5fps at VGA resolution e HIGH 20fps at VGA resolution A higher frame rate increases the traffic on the network Ask your network administrator for more details regarding the al lowed network traffic Images can be streamed with the built in web browser see page 26 If DHCP is de activated IP address and Subnet Mask have to match the settings on the computer Gateway IP of the SCB 12 has to be the IP address of the computer and the computers Gateway has to be
48. igher and updates via RS232 can be made with WolfVision s Firmware Up date Utility Both programs can also be found under the same link For a RS232 connection use a crossed serial RS232 cable Null modem cable IR Infrared Remote Control Please note that an infrared remote control can only be used up to a certain distance from the unit Objects situated between the SCB 12 and the infrared remote control and weak batteries interfere with reception If the SCB 12 can only be controlled from a close distance or if it cannot be controlled at all with the infrared remote control you may have to change the batteries Open the cover on the back of the remote control and replace the two 1 5 V AA batteries with new ones Check the polarity of the batteries Recycle batteries in accordance with local regulations Different IR Codes If you want to work with more than one SCB 12 in the same room the units should be set to different infrared codes in order to con trol them all individually To change the IR code enter the on screen menu go to Misc Settings and set the IR Code to A B C or D code A is default To change the IR code on the remote control simultaneously press PRESET 1 PRESET 2 13 and ZOOM TELE 12 Each time this key combination is used the code switches from A to B C D A in order given For resetting the remote control to code A simultaneously press PRESET 1 PRESET 2 and ZOOM WIDE
49. irmware yes via USB serial RS232 or Ethernet LAN USB software for image capture and controlling included for Windows and Macintosh Twain compatible with video capture driver Time for still image capturing 1 2 second approximate capturing time with fast PC and USB 2 0 User programmable presets 3 plus 8 fixed presets trough RS232 Image memory 9 pictures 1 image freeze Show all function displays all 9 pictures of current memory as one split image ves Alternative Image display negative image negative blue image black and white image RGB data RGB output 1X DVI output HDMI output DVI I analog and digital when using a DVI HDMI cable or adapter Trigger input positive or negative pulses switchable USB port standard USB 2 0 also compatible with USB 1 1 with less speed RS232 port and serial protocol with position setting and status report 1x Version 1 5 58 wore vision Technische Daten Ethernet LAN port yes IP addressable DHCP supported 10 100 Mbps Power Status LED External IR Sensor Test set or optional Dimensions W x H x L without interfacing board 62 47mm x 63 8mm x 110 57mm 2 x 2 x 4 3 Weight 0 8kg 1 8lbs Power Reguirements with power supply 12V DC 10 10W Power Reguirements with Power over Ethernet PoE class 0 36 57V Auto MDI MDI X
50. is also the opportunity to set the manual setting by performing a one push white balance By pressing the one push white balance key the White Balance will be set to ONE PUSH in the on screen menu ONE PUSH is a temporary setting and will be set back to AUTO TRACKING after switching the unit off on A correct white balance is necessary for a correct color reproduc tion see page 20 Adjust the right Color Mode for your application Additionally the gamma value and color saturation can be changed manually Factory setting is PRESENTATION Possible settings are e BLACK WHITE optimal setting for working with black white ob jects like x rays Saturation 0 and Gamma Mode 2 e PRESENTATION optimal setting for standard use with mini mum AE color difference Saturation 105 and Gamma Mode 1 e NATURAL optimal setting for natural color reproduction Satu ration 100 and Gamma Mode 3 e VIDEO CONF optimal setting for use with video conferencing systems Saturation 84 and Gamma Mode 1 e MANUAL gamma and saturation can be changed manually Adjust the gamma to match the gamma characteristics of the con nected display device for natural color reproduction Higher values result in brighter images and lower contrast e Oto 3 in integer steps wovrVsion 33 Version 1 5 OSD Qe quie Pos Neg Blue Color B W Return Detail DVI RGB Resolution Status Bar DVI is Return
51. l zoom extension e STOP the zoom stops when reaching the digital zoom exten sion For further zooming in press the ZOOM TELE key again e NONE no action when reaching digital zoom extension Returns to previous menu page OSD Settings wouvision SCB 12 OSD SETTINGS d Transparency ON X Size SMALL Menu Hor Position 5096 Menu Ver Position 5096 Status Position BOTTOM a Selection Bar Color m E Selected Text Color d M Menu Text Color LI m Menu Headline Color u Status Text Color LI Language ENGLISH Ki Return Freguency of displaying on screen messages Factory setting is TALK Possible settings e VERBOSE all on screen messages will be displayed e TALK only helpful messages will be displayed like Preset stored e QUIET only important messages will be displayed k Version 1 5 40 wore vision OSD Transparency Size L Menu Hor Position Menu Ver Position Status Position Selection Bar Color Selected Text Color Menu Text Color Menu Headline Color Status Text Color Transparency of OSD window background Factory setting is ON Possible settings e ON background of OSD window will be displayed transparent and the image is still visible e OFF background of OSD window will be displayed in solid color Changes the size of the OSD window Factory setting is SMALL Possible settings e SMALL the OSD will be shown as small window e LARGE the
52. n the SCB 12 Test set or optional available 4 5 6 7 8 N E 9 10 11 4 RS 232 for controlling purposes see page 24 5 USB for image transfers to the computer and for controlling see page 25 6 Trigger for triggering the unit see page 28 7 Etherne LAN for image transfers to the computer and for controlling see page 26 8 RGB RGB HV signal output see page 24 9 IR EXTERN for connecting an external IR receiver see page 25 10 DVI DVI I signal output see page 24 11 POWER power plug see page 24 wore vision 15 Version 1 5 IR Remote Control Test set 4 5 Infrared Remote Control 20 12 12 21 13 PRESETS IMAGE TURN 22 L1 02 L3 a 14 NHITE AF FOCUS 15 L JU UN ZN FREEZE ALL IRIS 23 16 I 17 MEMORY 24 Oe e q 4 5 6 Ip 26 18 pc v 19 MENU POWER 27 lazil wotrvision 12 ZOOM keys Using the ZOOM keys also switches auto iris on again 13 PRESET keys user programmable presets For storing a preset press one of the PRESET keys for more than 2 seconds For recalling a preset press the PRESET key quickly see page 19 14 AUTO FOCUS AF key Switches the auto focus on and off 15 WHITE key Activates one push WHITE BALANCE adjustment see page 20 16 FREEZE key Captures the current image see page 21 17 ALL key For displaying all 9 pictures of the memory as split image see page 21 18 MENU NAVIGATION keys For navigating through the on screen menu see pa
53. o a middle zoom position autofocus and auto iris are activated WoLFV SION 23 Version 1 5 Connections 7 Connections 7 1 DVI I NHENNNENE The DVI I port 10 provides digital and analog signals with ad Lt ois justable resolution and refresh rate enan n For using HDMI a DVI HDMI cable or adapter will be required DVI I When using digital display devices with LCD DLP or Plasma socket on the unit front view D Sub HD 15pin socket on the unit front view 7 3 GND DC plug pin diameter 2 1mm front view 7 4 00000 0000 D Sub 9pin connector on the unit front view technology use the DVI port for getting the best result of image reproduction Because the signal will be not converted from digital to analog to prevent signal loss RGB The RGB port 8 of the SCB 12 provides an analog RGBHV signal with adjustable resolution and refresh rate Use the RGB port for long cable runs and when using analog dis play devices Power Plug When a locked power connector and or other power supply are necessary the supplied power connector can be used The power supply is optional if Power over Ethernet PoE is used see page 27 The power source eguipment shall comply with all applicable local and national codes related to safety RS 232 The serial port 4 can be used to control the SCB 12 through an external device such as a room control system
54. optical zoom picture 600 22 x 30 44 x 59 392 x 522 800 28x37 55 x 73 517 x 589 1 000 33 x 44 66 x 88 642 x 856 1 200 38 x 51 77 x 102 768 x 1 023 1 400 44 x 58 87 x 116 893 x 1 191 1 600 49 x 65 98 x 131 1 143 x 1 525 1 800 54 x 73 109 x 145 1 269 x 1 692 2 000 60 x 80 120 x 159 1 394 x 1 859 2 200 65 x 87 130 x 174 1 394 x 1 859 2 400 71x94 141 x 188 1 519 x 2 026 Measurements in inch Length x Wide smallest I Bienes Pieturewith DIE largest pic feet m tical zoom 20 1 677 0 77 x 1 03 1 55 x 2 06 13 15 x 17 53 30 2 507 1 04 x 1 39 2 09 x 2 78 19 42 x 25 89 40 3 337 1 31 x 1 75 2 62 x 3 50 25 68 x 34 24 50 4 17 1 58 x 2 11 3 16 x 4 21 31 95 x 42 60 60 5 007 1 85 x 2 47 3 70 x 4 93 38 21 x 50 95 70 5 837 2 12 x 2 82 4 24 x 5 65 44 48 x 59 30 80 6 677 2 39 x 3 18 4 77 x 6 36 50 74 x 67 66 90 7 507 2 66 x 3 54 5 31 x 7 08 57 01 x 76 01 100 8 33 2 92 x 3 90 5 85 x 7 80 63 27 x 84 36 110 9 177 3 19 x 4 26 6 39 x 8 51 69 54 x 92 72 Version 1 5 10 woLgv sion Camera Pin assignment 3 1 3 Online Calculation Program Java A very easy method to calculate the exact positioning and the pos sible image sizes of the SCB 12 is the dedicated calculation pro gram on WolfVision s homepage a http Avww wolfvision com EYE 10 PSM 10 Calculation of zoom area in inch Micro E 3 EYE 10 EYE 12 PSM 10 SCB 1 and SCB 12 Calculation of
55. pin4 LED pin5 RS232 RX pin6 RS 232 TX pin7 GND pin8 DVI HP DETECT pin9 DVI 12C D pin10 DVI DC C pint GND pin12 VGA 12C D pin13 VGA I2C C pin14 GND pin15 VGA R pin16 DVI R pin17 GND pin18 VGA G pin19 DVI G pin20 GND pin21 VGA B pin22 DVI B pin23 GND pin24 DVI VSY pin25 VGA VSY pin26 DVI HSY pin27 VGA HSY pin28 GND pin29 TRIGGER IN pin30 GND pin31 12VDC pin32 12VDC pin33 5VDC pin34 3 3VDC pin35 GND pin36 USB DMINUS pin37 USB DPLUS pin38 USB VBUS pin39 ENET SPEED pin40 ENET ACT pin41 GND pin42 ENET TX pin43 ENET TX pin44 GND pin45 ENET 2V5 pin46 GND pin47 ENET RX pin48 ENET RX pin49 GND pin50 DVI TX2 pin51 DVI TX2 pin52 GND pin53 DVI TX1 pin54 DVI TX1 pin55 GND pin56 DVI_TX0 pin57 DVI TXO pin58 GND pin59 DVI TXC pin60 DVI TXC e For Ethernet LAN connection all ENET lines are necessary t use Tyco socket Tyco part no 1 6605834 1 wore vision 13 Version 1 5 Pin assignment Camera 4 3 quie quie Bottom Z3 Infrared receiver connector type S5B ZR pint 45VDC pin3 GND pin4 LED C pin2 IRX pin5 LED A Keep cable connections as short as possible IR receiver Vishay TSOP 38xx will be preferred Version 1 5 14 wore vision Test set Pin assignment Interfacing board 4 4 Interface Board optional The interface board is included i
56. plications for the Visualizers LAN port is constantly increasing It can be used for controlling capturing still images viewing live video streams firmware updates adjust ments menu settings and maintenance purposes The following protocols are supported TCP IP ICMP and ARP Supported internet browsers are Internet Explorer Netscape Nav igator and Mozilla Firefox By default DHCP is activated to receive all network settings auto matically Possible image transfer resolution up to SXGA 1280x960 In order to prevent unauthorized users from logging into the Visual izer over the network it is possible to set administrator and user passwords The transmission of the passwords over LAN is en crypted with Md5 The Visualizer offer streaming of live images in Singlecast Unicast and Multicast mode Technical Background In Singlecast mode each computer opens a separate connection to the Visualizer which requires a lot of bandwidth if many clients are connected Multicast is like a broad cast many clients are watching the same video stream In Mul ticast mode the bandwidth is always the same no matter how many computers are connected However as many routers do not support Multicast it cannot be used everywhere This is why both streaming modes are important Please check the separate description of Built In WebServer on our internet homepage at www wolfvision com support or on the supplied CD Rom For full f
57. r 24 months for Visualizers shipped before 2005 and used units From July 1st 2010 WolfVision also offers their end customers the possibility to extend their standard warranty of 36 months for an other 24 months by registering their new product within three months from the effective purchase date sale dealer to end cus tomer under www wolfvision com registration If during this period of standard or extended guarantee the prod uct should fails due to defective materials or faulty workmanship all defective parts components will either be replaced or repaired WolfVision will account for all spare parts and labour In such a case all products have to be labelled with a WolfVision Return Merchandise Authorisation Number and sent to a WolfVision Ser vice Centre Shipments without RMA number will not be accepted Therefore prior to any return shipment a WolfVision Service Cen tre has to be contacted to obtain a RMA number and to clarify the shipping method and shipping address Replaced parts are WolfVision s property This guarantee does not include claims for nullification of the sale depreciation reduction of the value or claim damages Dead on arrival DOA If the product fails immediately after arrival due to defective materi als or faulty workmanship it will be exchanged for a new model by WolfVision as soon as possible This is not valid for damages caused by disregard of the user manual In all other cases WolfVision
58. rier should perform a detailed inspection of all respective damages e Aclaim should be filed with the carrier e All documents paperwork etc should be faxed to WolfVision If the receiver detects damage loss upon opening the package and or the eguipment the receiver must file a claim with the carri er within 48 hours after delivery and then notify WolfVision in writ ing accordingly In the event that the receiver detects damage loss and does not file a claim with the carrier within 48 hours WolfVision will not be obliged to replace the product reimburse any damage costs or any other relevant costs incurred However WolfVision will co operate with the purchaser and if possible try to recover any incurred costs from their insurer In the case of not having received a shipment within one week of receiving the shipping details WolfVision must be informed imme diately Insurance cannot be guaranteed if a claim reaches WolfVision later than 10 days after shipment A guarantee repair does not extend the warranty period or start a new warranty period of the unit In case of any complaint please refer to our website www wolfvision com and contact your closest WolfVision office or send an e mail to support wolfvision com wa rev sion 71 Version 1 5 Disposal Disposal of old WolfVision units In the European Union Electrical and electronic eguipment marked with the symbol on the left have to be disposed o
59. rns L automatically back after 10 seconds Ok Confirms the selected resolution and returns to previous page Cancel Returns to previous menu page without any change wore vision 35 Version 1 5 OSD Recall Default Presets PRESET 1 2 3 Return Preset Control wote vision SCB 12 PRESET CONTROL Recall Default Presets a PRESET 1 PRESET 1 EI PRESET 2 PRESET 2 EN PRESET 3 PRESET 3 kl Return To set back all presets to factory default User definable adjustments 1 2 and 3 Factory setting is PRESET 1 2 3 Possible settings PRESET x for storing and recalling user selected adjustments POS NEG changes the behavior of key to toggle between posi tive or negative image display POS NEG BLUE changes the behavior of key to toggle be tween positive or negative blue image display BLACK WHITE changes the behavior of key to toggle between colored or black white image display WHITE BALANCE changes the behavior of key to perform an One Push Whitebalance like the White key FREEZE changes the behavior of key to capture the current picked up image IMAGE ON OFF changes the behavior of key to switch the im age output on or off IMAGE TURN rotates the image electronically page 22 Returns to previous menu page Version 1 5 36 wore vision OSD Power Settings Miscellaneous Settings OSD Settings Ethernet Settings Device Info Date Time Settings Return Advanc
60. s auto iris and manual iris and motorized zoom There are special features like trigger function 9 Presets remain stored when disconnected from power Positive Negative 9 image memories Freeze function and Image Turn The SCB 12 can be controlled by RS 232 USB or Ethernet LAN It is possible to transfer images via USB or Ethernet LAN Supply voltage is 12VDC 10 The PoE function can be used with the WoliVision interfacing board only 3 1 Picture Size 3 1 1 Chart The following chart shows the connection between distance from the SCB 12 to the object and image size in optical zoom range 0m mm im 3 28 2m 6 56 mi 3m 9 84 4m 13 12 5m 16 407 6m 19 69 7m 22 97 Object distance 8m 26 25 5 29 53 14 Zoom range H s I 10m 32 81 horizontal size 4 vertical image size e Regular Distance From 0 5 to 10 Meters 1 64 to 32 817 wore vision 9 Version 1 5 Pin assignment Camera 3 1 2 Picture Size Distance Camera to Object examples Measurements in mm Length x Wide smallest Distance dE Mid i cure uh sn ao UD
61. s with a soft tissue light reflec caused by room check room light conditions tions light sun light caused by glossy document switch off the light and work with room light image too dark Iris closed press IRIS OPEN key to open the IRIS or press a ZOOM key to activate AUTO IRIS wrong settings on display device check settings bad wiring to the display device Auto Iris Level check wiring Termination check Auto Iris Level in the on screen menu image too bright wrong colors Iris open wrong settings on display device press IRIS close key to open the IRIS or press a ZOOM key to activate AUTO IRIS check settings bad wiring to the display device check wiring Termination Auto Iris Level check white bal ance check Auto Iris Level in the on screen menu perform an One Push White Balance or change the White Balance settings in the on screen menu RGB check wiring to the display device Version 1 5 68 wourVision Troubleshooting SYMPTOM no color black white POSSIBLE CAUSE SOLUTION wrong gamma check gamma setting in the setting on screen menu Color set tings bad wiring to the check wiring display device wrong display set check display settings tings Unit is set to black white ch
62. sing the MENU key for 4 seconds the Extra Menu appears In the Extra Menu settings like baud rate can be changed The functions of the on screen menu are not described in detail in this user manual since the HELP menu is an integrated part of the unit s software firmware The information you see on your screen always belongs to the current firmware Reset On Screen Menu Settings The settings in the on screen menu can be set to default Recall Default Settings is a separate item in the on screen menu set tings regarding output and communication are not affected In case you are not able to read the menu on the screen you can also set the unit back to the factory defaults by simultaneously pressing both FOCUS keys on the unit 23 and the Number 4 key back arrow 18 on the remote control if available If you only want to reset the item that is currently selected to the default setting press the HELP key 25 for 2 seconds wa rev sion 29 Version 1 5 OSD 8 2 8 2 1 Exposure Settings Color Settings Output Settings Preset Control Advanced Settings Recall Default Settings Start Guick Setup Guide Exit Structure and functions of OSD The structure of the menu depends on the installed firmware ver sion The shown structure conforms to the firmware version v1 20b Standard Menu wour gion SCB 12 MAIN MENU Exposure Settings Color Settings Output Settings
63. the Subnet Mask manually Factory setting is 255 0 0 0 Ask your network administrator for more details regarding the in t stalled network Gateway IP De activate DHCP and set the Gateway IP Address manually Factory setting is 0 0 0 0 Ask your network administrator for more details regarding the in t stalled network Returns to previo Return p us menu page wore vision 43 Version 1 5 OSD Multicast IP L Multicast Port L Streaming Mode Streaming Settings wa ev sion SCB 12 MULTICAST SETTINGS Multicast IP 232 1 1 1 T Multicast Port 8800 Pi Streaming Mode AUTO GJ Streaming Format VGA Frame Rate LOW kl Return Changes Multicast IP address of camera Factory setting is 232 1 1 1 Possible settings are e 225 1 1 1 to 238 255 255 255 Ask your network administrator for more details regarding the in stalled network Changes Multicast destination port Factory setting is 8800 Possible settings are e 8800 to 9000 Ask your network administrator for more details regarding the in stalled network The corresponding source port is one port higher as the multicast port Streaming Mode Factory setting is AUTO Possible settings are e OFF Streaming disabled e UNICAST Camera streams permanently using unicast e AUTO Camera streams on demand only when clients are lis tening e CONTINUOUS Camera streams permanently using mult
64. the behavior of erasing image memories Factory setting is MANUALLY Possible settings e MANUALLY image memories can be erased only by keeping pressed the ALL key for 4 seconds and pressing MEMORY 3 key e STAND BY image memories will be erased when switching the unit on Images will be stored in a permanent memory without battery Changes the behavior of turning images by pressing the IMAGE TURN key Factory setting is CYCLE e CYCLE every time the IMAGE TURN key is pressed the image will be turned clockwise by 90 0 90 180 90 and 0 e 90 the image will be turned by 90 when pressing the IMAGE TURN key again the image will be displayed in standard format e 180 the image will be turned by 180 when pressing the IMAGE TURN key again the image will be displayed in standard format e 90 the image will be turned by 90 when pressing the IM AGE TURN key again the image will be displayed in standard format wore vision 39 Version 1 5 OSD Digital Zoom Dig Zoom Warning Return OSD Level Changes the behavior of digital zoom Factory setting is 2X Possible settings e 4X digital zoom extension is 4x e 2X digital Zoom extension is 4x e DISABLED digital zoom is disabled Changes the behavior of the unit when reaching the digital zoom extension Factory setting is MESSAGE Possible settings e MESSAGE a message will be displayed on screen when reach ing the digita
65. the noise reduction of images with little mo tion Reset password to default Password Exits the menu PASSWORD RESET GUICK SETUP GUIDE kkk kk kkk kk Master Password Ki Return Select Setup Language to select the desired language limited different languages are available see page 42 Select Next to skip this point If the Admin password is lost or forgotten contact your WolfVision dealer www wolfvision com to reset it to factory default Pass word The Master Password is depending on the serial number e Possible characters are 0 9 a z and A Z e 10 digits Write down the passwords and keep it securely If you forgot the password or lost it the access through the Ethernet LAN port may be denied Contact your WolfVision dealer in such case www wolfvision com Returns to previous menu page wourVision 53 Version 1 5 Resolution and refresh rate 9 Resolution and refresh rate WARNING Damaging the display device Not specified resolutions and refresh rates can dam age the display device Note the information in the manual of the con nected display devices e The SCB 12 has a native resolution of SXGA 1280x960 pixels L 720p 1280x720 pixels and WXGA 1280 x 800 Other resolu tions will be converted The DVI output 10 and RGB output 8 can be set to the follow ing resolutions and refresh rates
66. unctionality JAVA version 1 5 0 or higher is necessary For full functionality following ports are necessary 50915 50913 8800 and 8801 by default Version 1 5 26 wouFVsion Connections 7 7 1 Edo Power over Ethernet PoE The Ethernet LAN port 7 of the SCB 12 includes Power over Ethernet PoE functionality Power over Ethernet is a popular way of saving cables and installa tion costs The SCB 12 is compatible with PoE power injectors or PoE switch es according to the IEEE 802 3af 2003 industry standard The supplied Voltage in the range between 36 and 57V will be added to a CAT 5 or higher Ethernet cable and the camera can receive power via the Ethernet LAN cable A switch mode power supply in the camera converts the power to 12V When selecting a PoE adapter for the SCB 12 it is very important that the adapter complies with the IEEE 802 3af 2003 industry standard Before this standard was introduced many incompatible PoE systems were available on the market Some of these units with different PoE standards are not compatible with the SCB 12 and may have damaging effects The power classification of the SCB 12 is Class 0 0 44 to 12 95W More information on PoE adapters at www wolfvision com wolf thirdparty html wovrVsion 27 Version 1 5 Connections 7 8 7 8 1 7 8 2 7 8 3 Trigger The trigger mode is very useful for surveillance and machin
67. ures Effective Pixel 1280 H x 960 V 2048 x 1536 Total pixels of CCD 1 315 648 Pixels processed per second zeffective pixels x frames per 36 864 000 second Color reproduction very good colors SRGB color precision Native signal output SXGA 1280 x 960 720p 1280 x 720 and WXGA 1280 x 800 Output signals 1080p 720p WSXGA WXGA WXGA WXGA SXGA SXGA SXGA XGA SVGA VGA switchable LAN USB 2 0 Resolution measured 820 lines Resolution in Image Turn mode 1050 lines measured Image Turn mode for increased resolution yes 90 180 and 270 degrees Vertical image frequency Progressive Scan 85 75 60 or 50Hz switchable depending on resolution Horizontal image frequency Signal format Min Illumination Progressive Scan 31 5 91 1 kHz non interlaced 5 Lux typ Lens Integrated 12 x Optical Zoom Lens f 5 8 69 6 mm F 2 8 3 0 Lens Structure 10 Groups 13 Pieces 2 Aspheric Lens Adaptor M46 x 0 75mm Mount for Additional Lenses or Filters MOD Minimum Optical Dis tance Tele 0 5m Wide 50mm until Infinite for shorter distances standard close up lenses can be used Digital Zoom 4 x digital Iris automatic and manual White balance adjustment automatic manual and One Push White Balance Focus automatic and manual On screen menu and on screen help yes Upgradeable f
68. zoom area in in Click here to calculate in mm ceiling size of ceiling mount C sucalzer depending on model Maximum pickup area Length 50 inch width 67 66 inch picture Minimum pickup area Length 2 77 digi zoom 2 39 width digi zoom dimension tolerance 15 7 Enter a value between 20 and 390 inch or 1 67 and 32 5 ft and press Calculate Print this page B Internet www wolfvision com wolf indexdistance htm wore vision 11 Version 1 5 Pin assignment Camera 4 Pin assignment 4 1 quie quie For more details regarding the connectors please contact WolfVision Headquarter at support wolfvision com Keep cable connections as short as possible to prevent interfer ences Left side 1 Key panel connector type ZIF 12 RM1 0 pint KYP_AF LED pin2 KYP ROW1 pin3 KYP ROW2 pin4 KYP ROW3 pin5 KYP ROW4 pin6 KYP ROW5 pin7 KYP COLI pin8 KYP COL2 pin9 KYP COL3 pin10 KYP COL4 pin11 KYP COL5 pin12 KYP COL6 Keep cable connections as short as possible maximum 10cm The complete key matrix will be found on page 63 Version 1 5 12 wore vision Camera Pin assignment 4 2 Rear 2 Signal connector type 60PS JMDSS G 1 TF d Dim GND pin2 IR Data pin3 LED
Download Pdf Manuals
Related Search
Related Contents
Samsung GALAXY S GBC 4400310 binding machine RITCHEY User Manual Introduction Before Your First Ride GE X2600 Digital Camera User Manual Manual de l`opérateur Copyright © All rights reserved.
Failed to retrieve file