SMARTDBConfig Manual - Geotech Instruments, LLC
Contents
1. 3 3 4 How to Delete Rename or Modify Structure essen 3 3 5 UCS SU E etsi Ratte dame R MEM O po O Lu to tto ee 3 6 4 APPENDIX A SMARTGEOHUB CENTRAL STATION DATA FLOW DIAGRAM 4 1 SMARTDBConfig User s Manual Page Intentionally Left Blank SMARTDBConfig User s Manual List of Figures Figure 1 1 SMAHTDBOGontig 1 1 Figures ic 3 1 Figure 3 2 Top Node Right Click 3 2 Figure 3 3 Station Configuration Window 2 3 3 Figure 3 4 Site Configuration Window 3 4 Figure 3 5 Channel Configuration Window 3 5 Figure 3 6 Typical Delete Confirmation Message 3 6 SMARTDBConfig User s Manual Page Intentionally Left Blank SMARTDBConfig User s Manual About This Document This manual is designed for technical personnel installing and operating Geotech Instruments SMARTDBConfig Client application The following chapters included in this manual e Chapter 1 General Information about SMARTDBOConfig Client e Chapter 2 Installation and Setup Chapter 3 SMARTDBConfig Client Features and Operation SMARTDBConfig User s Manual Page Intentionally Left Blank vi SMARTDBConfig User s Manual 1 General Information 1 1 SMARTDBConfig Client Overview SMARTGeoHub is a multi threaded data acquisition syste2. 180 Data Part 11003 Latitude 0 0 D Longitude 0 0 fat INDI G INDIA Elevation 0 0 amp RUSS3 l RUSS Active RUSSA WEE Figure 3 4 Site Configuration Window 3 3 3 How to Add a New Channel To add a channel to a site right click with your mouse on on the parent site node and select the Insert option Figure 3 4 The Channel Configuration Window Figure 3 5 appears Enter the name of the new channel in the right panel the following information and click the Apply button to save Name The channel name up to three characters without blank spaces Location Name An optional two character field used to differentiate between two like channels at the same site For example two vertical component channels could exist at the same site Channel Type sensor Type Single character designation of sensor type Choose from acceleration sensor a hydroacoustic sensor h infrasound sensor i velocity sensor v or weather sensor w S can also be used to designate other types of seismic sensors Sensor Sensitivity The sensor sensitivity given in Volts m s or Volts m s for velocity and acceleration sensors respectively Natural Period Sensor natural period in seconds Damping Sensor damping in fractions of critical damping Calibration Period The sensor calibration period in seconds Bit Weight Digiti
3. Figure 3 6 appears and the user can either continue or reconsider the delete action SMARTDBConfig User s Manual Do you want to delete Site 7 Yes No Figure 3 6 Typical Delete Confirmation Message To rename a structure element right click it with your mouse select the Rename option Type the new name either in the structure window or in the right panel If you type it in the right panel it appears in the structure when you click Apply To modify a structure element simply left click it with your mouse and change the information in the right panel Click the Apply button at the bottom of the right panel when changes are complete Clicking the Discard button deletes the user s entries 3 3 5 Error Messages The application tells you if any of the names are too long or the IP address is invalid if you forgot to enter the address its in the wrong form or there are too few or too many numbers For example Error x Station Hame can he langer than 8 characters Site must na langer than 5 characters Channel Mame must langer than 3 characters SMARTDBConfig User s Manual Invalid IP Address Please Correct You must acknowledge errors by clicking OK with your mouse before entering the correct information and attempting to apply it to the configuration SMARTDBConfig User s Manual 4 Appendix A SMARTGeoHub Central St
4. SMARTDBConfig User s Manual Version 1 4 Copyright 2003 2006 Geotech Instruments LLC Dallas Texas Revision History ww ome NN NC 0 SMARTDBConfig User s Manual Table of Contents ABOUT THIS DOCUMDBEN V LAGENERAT INFOR MA TION Suet esee dorso e cot oaa kosch 1 1 LS MART DECONFIG OVERVIEW d eerte te eee dO RA 1 1 12 S REMEI REME NS bo Se aa UE LEM bo 1 1 2 SMARTDBCONFIG CLIENT INSTALLATION cccscccccccccccccccccccccccccccccccccccccccccccccccccccccsccees 2 1 3 SMARTDBCONFIG CLIENT 3 1 gt OOLBAR o A ost e tus Ut ed nci re Sat 3 1 3 2 STARTING AND CLOSING SMARTDBCONFIG 2 100000000000 eee neo neon 3 1 5 9 TOCREATE A DATABASE STRUCTURE o o ony 3 1 IA ATOW103AGd AN CW OUO ase ra o ees 3 2 3 9 TOV LO Ad GN GW i SILC sat au one o 3 3 23 9 9 HOW do Add a New Chanel zem 3 4
5. abase needed by SMARTGeoHubO This installation procedure assumes that you have no current SMART GeoHub installation on the computer Another procedure should be used to update or re install SMART GeoHube by double clicking on the Update program from the CD root directory The update procedure is similar to the install procedure but it excludes the installation of the relational database When the software installation is completed it is recommended to create or update existing shortcuts on the Desktop to point to the SMARTGeoHubO programs The SMARTDBConfig shortcut should point to the following program file given here as an example NSMARTGeoHubNSMARTDB ConfigNMbinNSmartDB Config bat Also it is recommended to set the program icon by editing the shortcut Properties to point to SMARTGeoHub icons SmartDBConfig ico Double click on the SMARTDBConfig icon to start the SMARTDBConfig Client 2 1 SMARTDBConfig User s Manual Page Intentionally Left Blank 2 2 SMARTDBConfig User s Manual 3 SMARTDBConfig Client Operation This chapter describes how to use the SMARTDBConfig Client The Client desktop consists of three areas a small tool bar an area for creation and display of the database structure and an area for structure settings Users should be prepared to create a structure for their station s sites and channels and identify specific information for each element of the structure This includes informatio
6. ation Data Flow Diagram SMARTGeoHub Central Station DR2SMART SMART24Config SMARTGeoViewer SMART 24D 9 Remote Setup amp Data Remote Setup Client Display Client SMARTDBConfig 7 Data Base Setup Client SMARTServer Data Server and Forwarder Data Base gt Monitor Client SMARTGeoSOH SMARTSUDSGen SeedLinkToSMART Data Client Data Server NDC I DC EarthWorm SeisComp USGS LISS SMARTQuake SMARTShake Typical Configuration 4 1 SMARTDBConfig User s Manual Page Intentionally Left Blank 4 2
7. m for real time operation Data sources are SMART 24 Series instruments DR 24 D Series Remote Digitizers or other digitizers communicating through supported protocols SeedLink Earthworm A data server SMARTServer stores seismic array data on a backend relational database as shown in the figure in Appendix SMARTGeoHub can also send data to other data acquisition systems using the SeedLink Earthworm or CD1 1 protocol SMARTDBConfig Client Figure 1 1 creates the structure used by this database The database structure consists of stations sites and channels Channels are defined as the sensor outputs for a specific site A station may include several sites Remote sites connect to the SMARTGeoHub over a TCP IP network They communicate through a well defined protocol that authenticates pre defined clients In order for the SMARTGeoHub to accept remote connections from remote sites the seismic array network must be configured in the database ini xi Configure Help SMART Config e E India y RUSSI ch1 01 ch2 01 ch3 01 ch4 01 ch5 01 bz m Welcome A INDIZ to the E amp INDI Smart Series y INDIB INDIS y RUSSA y INDIS common sense amp S INDI UNCOMMON innovation RUSS www geoinstr com Ge A RUSS RUSS Figure 1 1 SMARTDBConfig Client 1 2 System Reguirements The minimal hardware requi
8. ma innovation www geoinstr com Figure 3 2 Top Node Right Click Menu 3 2 SMARTDBConfig User s Manual lt DB Config Configure Help ART DB Canfig 7 5 Insert e 3 Delete 3 Rename ee Figure 3 3 Station Configuration Window 3 3 2 How to Add a New Site To add a site to a station right click with your mouse on on the parent network station node and select the Insert option Figure 3 3 The Site Configuration Window Figure 3 4 appears Enter the name of the new site in the right panel and the following information and click the Apply button to save Name The site name up to 5 characters without blank spaces IP The site IP address Data Port The port number at which the digitizer and SmartServer will communicate usually between 10000 and 32767 Longitude The site location longitude in degrees north being positive Latitude site location latitude in degrees east being positive Elevation The site elevation in meters Active Identifies a site as enabled active or disabled inactive Only active sites are allowed to connect to the SMARTGeoHubO server Configuration information for inactive sites may be stored for historical purposes 3 3 SMARTDBConfig User s Manual SMART DB Config 1 nml Configure Help SMART DB Config 182 158 100
9. n such as the sensor type and sensitivity site location latitude longitude and elevation and IP Internet Protocol address and network IP address The bar between the structure area and settings is movable to facilitate viewing of the information If the structure exceeds the available area scrollbars appear at the bottom and right edges The structure is expandable and collapsable by clicking the symbol to the left of any structure element When Select All Channels is clicked under Configure in the toolbar all structure elements are expanded and all channels are selected This facilitates channel settings when all channels are similar 3 1 Toolbar The toolbar Figure 3 1 includes three functions Configure allows the user to Select All Channels in a network facilitating information entry when all of the settings are the same or similar he Exit selection closes the SMARTDBOConfig client e Help tab will provide information about the SMARTDBConfig Client TBD Configure Help SelectAll Channels Repair Tables Figure 3 1 Toolbar 3 2 Starting and Closing SMARTDBConfig Client Start SMARTDBConfig Client by double clicking on its shortcut icon To close SMARTDBOConfig Client either click Configure followed by Exit or click the X button in the application s upper right corner 3 3 How to Create a Database Structure SMART database structure consists of a network of station s monitori
10. ng one or more sites and the sensor channels that send data to sites In typical seismological applications a station is defined as a seismic network consisting of seismic stations here referred to as sites with sensors having components here referred to as channels The configuration window the left area below the toolbar is where you ll create the network structure You ll enter the details for each structure element in the 3 1 SMARTDBConfig User s Manual right area of the Client The following procedures tell you how to add stations sites and channels to a network 3 3 1 How to Add a New Station To add a new station to the existing configuration right click with your mouse on the top node SMART DB Config v 1 0 and select the Insert option Figure 3 3 on the menu that appears The Station Configuration Window Figure 3 3 appears Enter the name of the new station up to 8 characters and its Internet Protocol IP address in the right panel and click the Apply button to save Do not include blank spaces in the station name The station IP address is the IP address of the workstation where the SMARTServer Data Server is running The Collapse and Expand selections on the menu allow the user to hide or view the configuration structure DB Config In x Configure Help SMART o E i Colapse 3 Insert 3 Delete 3 Rename Welcome to Smart Series COMMON sense hti
11. rements are a computer with Intel Pentium IV 2 26GHz processor 512 MB RAM with Microsoft Windows operating system Additional resources may be required to support large seismic networks Support for Linux and Unix operating systems is also available The computer must support 1 1 SMARTDBConfig User s Manual Suns Java Virtual Machine and include a relational database such as Oracle MySQL Postgress SyBase Cloudscape etc that has a Java Data Base Connectivity JDBC driver 1 2 SMARTDBConfig User s Manual 2 SMARTDBConfig Client Installation The SMARTDBConfig Client is installed as part of the SMARTGeoHub data acquisition system The install procedure is very simple and automated as described below To install SMARTGeoHub onto your computer Insert the Geotech s SMARTGeoHub CD in the system CD drive and double click on the Install program from the CD root directory This procedure will create all folders and will copy all files necessary to run SMARTGeoHub On a Windows platform the installation folder defaults to c SmartGeoHub where the SMARTGeoHub programs will be installed in different subfolders one for each software component Next the Java Runtime Environment will be installed or updated to the newest version if already present on the computer The Typical setup should be selected during the Java Runtime Environment Install Wizard The install procedure will also install the relational dat
12. zer bit weight in uVolts digital counts SMARTDBConfig User s Manual System Sensitivity Instrument Name Instrument name e g 5 2000 Broad Band Active Identifies a channel as currently active or inactive disabled Data for inactive channels is not stored in the database but configuration information may be stored for historical purposes Note the following he menu that appears when you right click on the site node allows you to Expand the configuration display and view the channel names attached to the site e f you right click with your mouse on a channel the channel can be deleted or renamed The insert option is not available since sub components do not exist for channels ipi xd Configure Help SMART Config Channel Mame cH Location Name m 5 First Primary F n Rename Sensor Type velocity Sensor Sensitivity 629 0 m Hatural fs Damping 07 Calibration Period 10 sj Bit Weight oo fp Vieeunt System Sensitivity nmicocunt Manual Instrument Hame BroadBand y RUSS Figure 3 5 Channel Configuration Window 3 3 4 How to Delete Rename or Modify Structure Elements To delete a structure element right click it with your mouse and select the Delete option Note that this will delete all children nodes of the selected node A delete confirmation message
Download Pdf Manuals
Related Search