INTRODUCTION WELCOME TO THE MONTY FAMILY
Contents
1. Use a wet piece of cloth with water and soap to clean the vehicle later take care to dry all the wet parts avoiding the electric connections not to get wet Do not use strong products which can deteriorate the paint cables or rubbers Verify the kind of product before using it Do not wash your DPIE 4 using a high pressure water system The water could enter into the bearings and other parts deteriorating their effective work N Important to use original pieces It is extremely important to use always parts when replacing DPIE 4 components Not doing so may invalidate the manufacturer s warranty 14 TECHNICAL CHARACTERISTICS CHARACTERISTICS Front Wheel 350 W Brushless 48V 20Kmh 4z SJ Front 13x 5 00 6 Hear 2 80 2 50 4 D PIE 4 29 Kg Seat seat post 2 Kg Seat support 1 Kg Basket 0 9 Kg Tow 6 3 Kg User max weight 100 Kg Luggage max 10 Kg weigth User luggage 100 Kg Lithium 48 V 12 Ah Note The above specifications can be changed without previous notice 21 15 MAINTENANCE CHART This chart reflects maximum values and may vary depending on the use given to the bike and the resulting wear of each riding style It can also vary depending on the terrain weather riding style etc Components Inspection Lubrication replacement Seat post ee Handlebar Wheel 1 month alignment Ps Fork Headset Brakshoes pads 1 month Excess2. nmn Figure 12 The indicator is more reliable while the vehicle is running It is normal if a light goes out on starting this means that the consumption is important e All lights on Battery charged Ready to start e Green light out Battery to 60 70 One can ride with prevision e Two Green lights out Battery to 40 50 Few charge e Three Green lights out Battery to 10 20 The battery should be charged e Only the red light Battery discharged The battery must be charged once 18 The environmental temperature can affect the good work of the battery In general the battery is to work properly in high temperatures When the temperature drops below 0 C however its performance can be reduced to a third For this reason it is probable that the charge can last less time in winter At 20 C the battery shall work normally When the temperature exceeds 35 40 C or if the battery has been exposed to the sun for a long time the electrical components may not work normally Actions which may effect or reduce the battery performance Constantly starting and stopping the DPIE4 as it can be driving in cities Constantly braking and turning the bike on and off Hiding upwind or uphill and carrying extra weight Low pressure tire and braked wheels These actions can influence the battery s performance reducing its life and the distance which can travel to be shorter We recommend to take note of the above indicated points to
3. change any of the DPIE 4 technical characteristics and not to add any devices which may interfere with them e Recommended to use safety equipment 5 VEHICLE ASSEMBLY The vehicle assembling shall be done in a light level and clean place with some basic mechanic knowledge Or you can get in touch with your distributor or with Monty in order to solve any problem e Components o D PIE 4 platform Stem and Handlebar Integrated Charger Ignition key User s manual O G G Q e Assembling instructions 1 Take out all the parts from the box and verify to be all the required items Remove the D PIE 4 protector cartons with care 2 Fit the stem to the handlebar OPTIONAL 3 Assembly the seat post to the platform placing all the fastening nuts as it is shown in the assembling scheme Ke See section MAINTENANCE AND MECHANIM for a right assembling e Charge of the battery 1 The battery must be charged on the whole before the first riding ke see section BATTERY AND CHARGER for a right charge 6 USER S GUIDE DESCRIPTION DPIE 4 is a personal mobility vehicle provided with a platform with three wheels The integral electric engine is set on the front Wheel in order to give traction to the vehicle and the steering through the handlebar as well getting a great handling One can change the direction in a small space thanks to the position of the feet as well TYPE OF USE FOR WHICH THIS BIKE HAS BEEN DESIGNED MONTY DPIE 4 and t
4. extend as much as possible the travelling distance that the DPIE 4 can travel 11 1 BATTERY RECHARGING Ensure the battery to be charged completely before using the vehicle for the first time The battery can be to the 5096 charged when one may receive the vehicle DPIE 4 is provided with an integrated recharging system to the vehicle with an external plug in the front part Figure 13 directly to the system which is retractable On the rear part of the Central covering Figure 14 there is a switch to connect the charger and two informative light led to know the level of the charge This easy to charge the battery to any place without needing any external charger In this way the charger system is always ready without problems Figure 13 Figure 14 UTILIZATION OF THE SYSTEM STEPS TO FOLLOW TO CHARGE THE BATTERY PROPELY Make sure the contact key to be in position OFF Connect the plug to the electric system To initiate the charge push the Red button from the rear side of the covering The light leds indicate the position level of the charge To stop the charging push again the Red button take out the plug from the electric system por IS 19 Figure 15 Figure 16 Figure 17 Figure 18 MEANING OF THE LIGHTS LEDS RED LED MEANS The charger is connected to the electric system YELLOW LED The charge is being charged Figure 16 GREEN LED The battery is already charged Figure 17 OFF LED The charger is disconn
5. of the bike and fall down Ensure that the headset and stem to be correctly fitted before each use 10 4 BRAKES Ensure the correct work of the brakes DPIE4 is only provided with a sole disc brake per cable to the front wheel which allows to stop the vehicle without problems The brakes shall work and allow the vehicle stop at a safety and proper distance On using the brake lever the engine is also disconnected Check the brake shoes not to show any excessive wear The DPIE 4 model is fitted with a mechanical disc brake sytem The brake system of this vehicle allows to get down the speed a very safety critic function The following item explain how to inspect adjust and even lubricate the DPIE 3 brakes AN caution As any braking system an incorrect adjustment poor maintenance or a bad use of the brakes may cause one to lose control of the vehicle with all the consequences that this may imply Never use the bike if the braking system is not working correctly or if you suspect any type of problem either with the brakes or their cables If the brakes are not working correctly one may lose control and fall down If the DPIE 4 is not working properly fix it or take it to an authorized dealer 15 Adjusting the brake system is difficult if one does not have the necessary know how experience and the necessary tools We strongly recommend that any adjustment to the brakes be carried out by an authorized dealer Not all brakes
6. that if one detect any problem which can not solved by oneself please contact with an official dealer Take as usual the following checks before riding the vehicle Verifications before riding WHEELS HANDLEBAR AND STEM HEADSET AND FORK BRAKES BATTERY AND HARGER It is extremely important the brakes to work correctly for one safety and that of others Carefully check the brake system each time before riding and do not use the DPIE 3 if a problem is detected Ke see section MECHANISM AND MAINTENANCE 8 ADVICES Keep your bike clean to ensure proper functioning Protect the DPIE 4 against thieves Use a lock for more security Do not overpass the allowed weight Hide with care 4 See section SAFETY e No additional passenger is allowed on the DPIE 4 one person only e A speedometer can help to control the autonomy and maintenance of the vehicle Plan your route according to the autonomy of the vehicle Avoid water entering into the bearings The battery must be charged in an airing area A programmer by the charger plug is to help in the charger task 9 SAFETY DPIE 3 preventive actions 1 To brake or stop the DPIE 4 the user shall grip the brake lever rightly depending on the circumstances and the engine is to be disconnected automatically Bear in mind that the brake system works as follows One shall grip the left lever to brake the front wheel 2 DPIE 4 must be ridden by one person only 3 On rai
7. web site www monty es e By e mail e bike monty es e By telephone 93 666 71 11 We thank you for having dedicated some time to read this manual in order to improve the use of the new DPIE 4 We thank you as well for any point of view from your side 26
8. ADSET The headset must turn smoothly in both sides freely and be compact on the whole HEADSET INSPECTION Inspect your vehicle s headset once a month and check to make sure that it is neither too tight nor loose If either of these is the case do not use the bicycle and take it to your authorized dealer 14 HOW TO CHECK THE PLAYS IN THE HEADSET ADJUSTMENT Place oneself by the vehicle with the feet on the ground oqueeze the front brake while moving the vehicle forwards and backwards Check if the headset is loose The headset is formed by guards and bearings which are in contact to the frame below and above The handlebar and stem fitting can have a small play due to the stem holding system HOW TO CHECK THE HEADSET S ADJUSTMENT Place oneself by the vehicle with both feet on the ground With the front wheel resting on the ground turn the fork and handlebar from left to right and vice versa Look listen and feel if the headset is too tight making a noise as turning or snagging at different points ADJUSTMENT Adjusting the headset requires special tools and expertise Please see section Stem adjustment and subjection In case of any doubt please check it with an authorized dealer LUBRICATI N The headset should be lubricated once a year This requires specific know how expertise and special tools for this reason only an authorized dealer should do it ATTENTION An incorrect headset adjusting may cause one to lose control
9. INTRODUCTION WELCOME TO THE MONTY FAMILY Firstly we would like to welcome you and thank you for choosing the Monty brand This User s Manual for your new Monty electric bike DPIE 4 contains important information and necessary to keep your bike in good condition It has been designed so that you can enjoy of your vehicle safely making the most of your time Please read this manual carefully before using your new electric bike hereafter DPIE 4 and save this manual for future reference If you have any doubts or questions please contact your authorized Monty dealer Your DPIE 4 is fitted with a top quality engine and a battery of long lasting which will not require much maintenance Its innovative design and safe construction will provide you with km of satisfaction Parents or guardians should explain the contents of this manual to any minors using the DPIE 4 to ensure that they have understood its contents The drawings and images may not correspond exactly to your model They are used solely to facilitate your understanding We apologize if any part of this manual does not correspond with the precise characteristics of your DPIE 4 At Monty we always strive to improve our products As such we may incorporate other new technical components to the models or change pieces without prior notice Always hand this manual to any future owner of your DPIE 4 The Monty family is constantly innovating to offer its clients a top quali
10. OULD YOU HAVE ANY QUESTIONS OR DOUBTS PLEASE CONTACT YOUR AUTHORIZED DEALER OR VISIT OUR WEBSITE http www monty es CE European Confirming 1 NDEX SECTION PRESENTA HON T IMPORTAN err ICONS dQgo oomsom o C N e TI A OD Q c UO Mm 0 MECHANICS AND MAINTENANCE 10 1 Wheels 2 2 0 0 ccc ccc cc ccccccccccccceccccceccccecceccccecceacecceesueaueceeneanes 10 2 Handlebar and Stem ccccccccccececececececececececececeueceaenens 10 3 Headset and FOrk cccccccccccecececcccececccececeaeecees 10 4 B Fe ee ree oe eee eee eee 11 BATTERY AND CHARGER 11 1 B aE CNAIN RET TID 12 ELECTRIC COMPONENTS crrr ureri gE 13 CLEANING 14 TECHNICAL CHARACTERISTICS 2 UNDERSTANDING ICONS The following icons are in order to easy the manual understanding and to underline of the important items ES SEE SECTION o ee A CAUTION MAINTENANCE 3 DPIE 4 PARTS 14 15 16 THROTTLE IGNITION KEY SADDLE BATTERY LEVEL BRAKE LEVER STEM SEAT POST RELEASE QUICK RELEASE BASKET 10 CHARGER PLUG 11 BATTERY CAGE 12 FORK 13 SEAT SUPPORT 14 DISC BRAKE 15 DPIE PLATFORM Optional TOW 16 LATERAL WHEEL NUT 17 CHARGER SWITCH 1 optional parts 1 2 3 4 5 6 T 8 9 4 GENERAL NORMS e Please read this manual carefully before using your Monty DPIE 4 e Ensure that the bike works correctly before riding e We recommend you not to
11. are compatible with all types of levers For any brake be sure to use only compatible levers such as those that come originally with the DPIE 4 MECHANIC DISC BRAKE The mechanic disc brake press the brake shoes pads on the disc placed on the front hub instead of pressing the pads on the rim The disc is fitted to the axle by bolts to the left side The brake works by a cable coming from the lever to the pincers The brake system is formed by Brake lever Brake cable amp casing Brake pincers Brake shoes pads Disc ATTENTION The disc brake shoes can be very hot after using them please take care not to touch the disc on checking them INSPECTION oqueeze the brake lever 5 times before riding The levers must not touch the handlebar Ensure that there is no oil grease or any other matter on the disc The disc is part of the braking system and should always be kept clean Remove the brake shoes from the pincers for in depth cleaning Do not use any clean products degreasing liquids or solvents to clean the disc Use isopropyl alcohol Check once a month to ensure that the disc brakes are not worn down If the brake pads are less than 1mm thick they will have to be changed Check also to ensure that the pads are correctly positioned a distance between 0 25 and 0 75 mm from the disc when not using the brakes Turn the wheel while not pressing the brake lever The pads should touch the discs as little as possible L4 See secti
12. ected Figure 18 ATTENTI N The charger is equipped with a safety fuse of 25A in case that the charger did not work check the state of the fuse and change it if it were necessary 12 ELECTRIC COMPONENTS CONTROLLER DPIE 4 controller is the nerve centre of the system It consists of a small box placed under the battery compartment and where all the components are connected The controller receives all the necessary information from the brakes engine battery etc The controller is responsible of the engine to work correctly and the DPIE 4 safety as well The controller checking handling requires specific tools and know how Only an authorized dealer or the Monty plant should manipulate it ENGINE DPIE 4 is provided with a top quality resistant engine The engine is part of the front wheel designed to provide a maximum service with barely any maintenance The engine as part of the front wheel must be firmly placed as it is explained in the section on the wheels section Otherwise there is a risk of a serious problem Be especially careful with the engine cable which comes from the front wheel axle Do not bend cut or damage it in any way Important Avoid heavy hits to the front wheel and the rim as well since the engine could be damaged 20 13 CLEANING Clean the vehicle each time after having used the vehicle Do not delay the clean since such process can be more difficult once the mud and dirt get dried
13. eels removing To remove the wheel in case of a tyre getting flat or any other reason one shall follow the following steps Front wheel Make sure that the contact is out and remove the key Disconnect the cable connector in case that the vehicle was provided with it Loose the wheel axle nuts counter clockwise with a fixed key Remind the situation of the safety washers towards the assembling Remove the wheel in a vertical down position To assemble the wheel place the wheel at its correct position Fit the safety washers and tie the nuts clockwise Connect the engine cable and check the brakes to work properly Rear wheels To remove the rear wheel use a tube key suitable to the nut sizes Loose the nut and take out the wheel Remind the situation of the washers and the wheels To fit the wheels place the washers and the wheels to their original place and order and tie the nuts ke See section Torque value 10 2 HANDLEBAR AND STEM The handlebar must be centred to the stem and perpendicular to the frame The handlebar is fitted to the stem by a plate with 4 screws Loose the screws to regulate the handlebar position To fix the handlebar position in a right subjection tight the screws in alternate cross form The handlebar height can not be changed HANDLEBAR FOLDING AND ADJUSTMENT The folding of the DPIE4 handlebar is easy and practical Please check the explication in order to get an easy and safety folding Make sure t
14. hat no cables are over stretched or pinched when moving the different parts 12 To fold the DPIE 4 handlebar A to block the handlebar Figura 3 stem closing system Figure 3 STEM CLOSING Figure 4 FOLDING FOLDING First pull out the closing lever 1 Figure 5 Open the closing move the lever down and lateral to open the safety blockade Arrow 2 in Figure 6 unblockade closing Move the stem in the rear direction Figure 4 Folding Figure 5 OPEN CLOSING Figure 6 UNBLOCKADE CLOSING UNBLOCKADE To ensure the stem place it in a vertical position again Turn the stem forwards the safety blockade is to close automatically later close the closing lever to the final position Figure 8 Blockade closing The adjustment of the closing press can be regulated with the nut of the closing lever 13 Figure 7 UNFOLDING Figure 8 BLOCKADE CLOSING The handlebar and stem must be fitted correctly positioned and tightened in a suitable and safety position to the user Stem adjustment and subjection The stem is fitted directly to the fork tube to make the adjustment the lateral screws shall be loose lightly Figure 9 Lateral screws check the headset as it is explained on the following item and tight the system again First tight the central screw Figure 10 Central screw and later the lateral screws and check the Headset Figure 9 LATERAL SCREWS Figure 10 CENTRAL SCREW 10 3 FORK AND HE
15. he tires are to be in good state and properly inflated and the tread to be neither cracked nor worn down The drawing pattern must keep as the minimum 2 mm in order to provide good traction The sizes are indicated on the sides of the tires Make sure to get the tires suitable to the rim and the type of the vehicle o ADVISE The front tyre wears down quicker than the others by the traction avoid to slip on the starts The feet should be placed forwards on the platform in order to get more grip CAUTION When replacing a tire make sure to be suitable to the rim and the type of the vehicle The DPIE 4 tires are different from the standard ones Tire pressure Tires must be inflated to the right pressure to ensure the bike works properly The valve is the Schrader type like the ones used by the cars To inflate the tyre the valve shall be removed then and place the nozzle on the valve ensuring that no air escapes check the pressure and place the cap back on the valve to keep it from getting dirty If the inner tube gets flat it is recommended to be changed not to repair it Remember The maximum air pressure is indicated on the lateral tires side 11 The air pressure must be checked regularly PRESSURE TABLE Wheel Recommended Bar Kpa _ fo PSI Bar Kpa PSI Front 10 100 15 14 140 20 _ Rear 2 0 200 30 20 200 30 Equivalences approx 1 Bar 100 Kpa 14 5 PSI Wh
16. heir components have been designed for standard or industrial uses Its handling is to surprise you One shall get familiar to this vehicle in an area free of obstacles and safe and later in enclosures or areas always provided with an even ground Incorrect usage other than the above or riding cross county may lead to premature wear and tear loose joints and or component breakage thereby causing the cyclist to possibly fall and or injure himself herself This vehicle is not recommended to children under the age of 12 This vehicle is not recommended to persons weighing more than 100 kg This vehicle is not allowed to be run in the public means Please check the local rules HOW THE DPIE 4 WORKS MONTY DPIE 4 is simple and intuitive to be used Steps to follow before using 1 Connect the electric system Make sure the charger to be off Turn the contact key of the right lever to the position ON 5 The led lights on the information panel found in the contact lever will light up Indicating the battery charge level 4 The DPIE 4 is ready to be run The vehicle does not produce any noise while is still e To verify the battery charge while the vehicle is running is more exact than to be stopped 2 How to move the vehicle through the throttle DPIE 4 is provided with a throttle 6 set to the right grip in order to initiate the move of the vehicle If one turns opposite to the clock hands the engine is to speed if one turn
17. in any conditions which might threaten your personal safety The wall sock must meet the pertinent safety norms GOOD USE OF THE BATTERY The first charge of the battery is extremely important and can determine the battery s useful life Charge the battery complete 4 6 hours aprox The charger lights are to indicate the state of the charge Before using the DPIE4 the battery shall be charged before to be discharged on the whole and will last the battery The battery never should be run out on the whole It does not matter the km run Charge always the battery after having used the vehicle In case of not using the vehicle remember that the battery shall be charged at three or four weeks A Very important Always use the charger corresponding to your model 17 Any manipulation of the battery by the client will invalidate the warranty and free the manufacture of any possible liability Charge the battery in a well ventilated area The batteries have discharge It is normal the battery can have run out after a period of time without using it BATTERY AND CHARGER CHARACTERISTICS CHARACTERISTICS Type Voltage Capacit Lifetime years Number of the chargers Charge time Charger Charger input Charger output Charger fuse BATTERY CHARGE INDICATORS El DPIE 4 provides a battery charge indicator on the right grip Figure 12 This indicator has 5 light 3 Green 1 Orange 1 Red It is similar to a traffic lights
18. information to E bike monty es Name Address Zip code Town Country Telephone number e mail address Model purchased Parchase date Place of purchase Shop or authorized dealer or this information can be send by post to BICICLETAS MONTY S A DPTO E BIKE C INDUSTRIA 30 32 08980 SANT FELIU DE LLOBREGAT BARCELONA SPAIN 25 20 Guanratee A warranty is established through the vendor in accordance with the law 232003 dated 10 July from the consumer sale warranties and in accordance with the Directive 1999 44CE Additional conditions The warranty does not cover the DPIE4 parts subjected to normal wear such as tires chain brakes cables etc The battery and charger are covered by a guarantee Li ion Lithium battery 1 year Never use any other manufacturer s components Never repair the DPIE 4 by oneself Take it to the store where the vehicle was purchased or to an authorized Monty dealer In case this stipulation was not respected and in case of any problem or accident Monty shall not assume any responsibility nor be held liable and this warranty shall be rescinded Modifying the frame fork or any other component implies that the DPIE4 no longer conforms to our specifications thereby annulling this warranty 21 INFORMATION CONTACT AND DEALERS We recommend to get in touch with the dealer where the vehicle was purchased in case of any doubt or problem For more information e Monty
19. ive wear lt 2mm Brake levers 1monh 3monhs discbrake 3month wear 0 Folding pivots 1 month S months 16 ADJUSMENT CHART ee es e e Seat height Quick release 100N SEAT post Quickrelease OON Stem ahead Subjecionscrew 12 15Nm Brakeleverclump Fixscew 68Nm 15 Nm oo BEEN fe Cable clump bolts Strength 9 8N 1kgf Pincer bolts Assembling adapter bolts 22 17 SOLUTION CHART INCIDENCES POSSIBLE CAUSA SOLUTION Alter setting the battery to charge it looks like it dID not charge When turning the battery key the charge indicator does not light up The engine suddenly stops after moving just a few meters or when climbing a not very steep hill The engine stops or works irregularly after having use the vehicle continuously or on uphill climbs The battery has not enough autonomy The charger is not connected properly The charger does not work well The fuse is out The battery is discharged on the whole The fuse is shorted out or not connected properly The key switch does not work The cable has been detached from the battery The fuse is fused Engine overheated The fuse is fused The battery is discharged There is an electric malfunction The battery has not been charged properly The battery is not rechargi
20. ng correctly Adjust the connections to ensure good contact Ensure that the battery is in the right position ON OFF Verify the plug Check the charger light to be on Contact to the technical service in case it did not blink The fuse must be changed Check the battery indicator and recharge if it were necessary Check the fuse and replace if faulty see the technical service section Verify the connections and contact technical service if faulty Check to ensure that the battery is connected properly Check the fuse and change it if it were necessary see technical section Intensive and continuous use of the bike at maximum power may overheat the engine and its controller In this case wait a few minutes to let them cool down Check the fuse See the relevant section Check the battery charge The amount consumed may be different depending on the external riding conditions Check the electric connections See the relevant section The battery has to be in top conditions to achieve the full charge autonomy established in this manual You also have to consider that the distance you ride will vary depending on the rider s weight the trajectory or DPIE3 conditions contact to a technical service A strange noise can be hear for the front wheel engine The brakes make noise or they do not brake very well The wheel is not aligned properly The spokes can be loose The engine gears are wo
21. ny or snowy days reduce the speed to avoid incidents 4 Avoid riding on rainy days days with heavy snowfall or through flooded areas Efficient riding The range and performance of the DPIE 4 depend on some factors These can be classified in two types e External related to the environment conditions surface weather etc e Internal related to the vehicle state and the running style as well The external factors can not be changed but yes to select a route adapted to the characteristics of the vehicle The internal factors more related to the user can be adapted in order to improve the lasting of the battery and the life of the vehicle Advises Use the short gear to move the vehicle Keep the tire pressure rightly Verify the wheel to turn easily and the brake not to touch to the disc Keep a constant speed if it is possible Do not brake the vehicle suddenly let the vehicle to loose speed smoothly Do not overload the allowed weight on the DPIE 4 DPIE 4 safety riding A As with any other activity the use of this vehicle implies certain risks To get the Monty DPIE 4 such risks must be assumed by the user In no case the dealer or manufacturer are to be liable The riding of the DPIE 4 is different from the other vehicles by having three wheels One front central wheels and two rear ones This vehicle stays even on turning to the contrary from the bicycle performance The right position in order to drive the DPIE 4 is
22. on Torque Value Check your brake cables once a month to ensure that they are not twisted or rusted that there are no broken threads or ends and check their casings for cuts or wear Substitute any defective piece AJUSTMENT e How to regulate the cable tension use the tensor T and fix it with the locknut e How to adjust the separation between pad with respect to the disc Turn the pad s adjustment screw A To increase the separation turn it counter clockwise To reduce the distance turn it clockwise How to align the brake with the disc Loosen the brake mount bolts P Squeeze the lever completely and gradually tighten the bolts 16 e How to remove the brake shoes the pincer shall be taken out and with the fingers or thin nosed pliers grip the tab of the brake shoes and pull it A Adjuster nut set in the inside face P Assembling bolts of the pincer T Tensor F Fitting screw cable S Assembling bolts to the fork Figure 11 A Important The brake lever corresponds to the front Wheel 11 BATTERY AND CHARGE The battery is one of the most important part of the DPIE 4 Please make a correct use DPie 4 provides a LITHIUM ION battery with 48V 12Ah The battery can provide 300 chargers approximately L very important Do not allow children to charge the battery The electric charge 220V may cause serious personal injury or even death Do not charge the battery barefoot on a damp or wet floor or
23. phones as they reduce your ability to hear other vehicles e Never carry any additional passenger No matter to be a kid The handling Capacity and safety could be affected e Never load anything on the vehicle which might obstruct the vision or ability to control the DPIE 4 Never shall the user hold himself on another vehicle while riding Not to tow or be towed by other vehicles Not to ride the DPIE 4 under the influence of alcohol or drugs If it is possible do not ride in adverse meteorological conditions such as when the visibility is low in the dark areas or to be extremely tired e Never allow minors under the age of 10 years to ride the DPIE 4 10 N ATTENTION Caution regarding to the intensive use As any mechanical device DPIE 4 is to wear down with different efforts The different materials and components used may react differently to this daily decline If the lasting life of a given component has been exceeded it may suddenly break injuring the user The cracks scratches or discoloration in the areas subject to intense use indicate that the component has exceeded its useful life and must therefore be replaced 10 MECHANISM AND MAINTENANCE 10 1 WHEELS The rims and tires are an extremely important part of the DPIE4 and they should be kept in right condition Check the right pressure and control the wear out of the tires and the rim conditions Make sure that the wheels are well placed and fitted TIRES T
24. placing the feet each side of the central covering and in front of the rear axle The control system and the handlebar turns are effectuated by the hands To improve the traction of the vehicle on starting one shall bent forwards On turning the user shall bend the body towards the inside of the turning To brake the action shall be made in a smooth and progressive way Avoid suddenly and quick turns otherwise the vehicle can lost the balance and overturn Extreme the precautions on the turns while the seat is used Not to get the body too much to the rear part of the platform the vehicle could lost the balance and the front wheel could get up Not to brake abruptly the vehicle could unbalance Not to ride stoop kneeling or any other form except the right one DPIE 4 is not made to get up get down from the kerbs or to pass obstacles In case that one should face it one should get down from the vehicle e A mechanical revision must always be done before getting on the DPIE 4 Ensure that the brakes work properly One must get familiarized with all the components of the DPIE 4 It is recommended to wear a helmet to ensure greater personal safety Wear always appropriate shoes to use the vehicle correctly Wear reflecting or very visible clothing whenever possible Do not use the DPIE 4 to jump Attention with the irregular surfaces Keep the speed under control and safe to avoid losing control of the DPIE 4 e Never ride with ear
25. rn the bike is still brand new It needs a little running The brakes are not aligned The brake levers can not be tightened properly The brake shoes are worn Check the alignment of the wheel Tight the spokes The bearings in models without brushless engine may wear out In this case contact an authorised dealer to replace them It is normal in a new bike for brakes to make some noise If after a few days of use the noise persists check the brakes to be aligned Place the brakes in the right position see the relevant section Check the lever tension by means of a regulator Check the brake pads and replace them it were necessary 18 FREQUENT ASKED QUESTIONS Can the DPIE 4 be washed with water Yes but we especial care mainly in the areas with electric connections Do not wash using a high water pressure system Is it possible to run in the rain Yes if it is not raining hard Avoid to pass through puddles or wet areas Can the DPIE 4 be let out We recommend to protect the vehicle and store it in a covered area mainly in the coastal areas What happens if the DPIE 4 has not been used for a long time The maintenance of the battery shall be made even if the vehicle is not used 24 19 CLIENT CONTAC FORM Dear Client If you want to be kept up to date on the latest Monty electrical products including everything related to the World of the E bikes send an e mail with the following
26. s to the clock hands the engine is to brake It is provided of two shifters one short and one long 2 to be used according to ones requirements 3 How to stop or decrease the speed If one uses the brake lever 1 the engine assistance and the transmission are to be interrupted so one shall grip the brake lever to stop the vehicle Remember that the DPIE is only provided with a front wheel brake Figura 1 Figura 2 1 BRAKELEVER 4 BATTERY NIVEL INDICATOR 2 SPEED INTERRUPTOR 5 IGNITION KEY 3 HORN PUSH BUTTON 6 THROTTLE Remember that the brake for safety works on the electric system cutting the engine current Important Before using the vehicle please see the section VERIFICATIONS Y SAFETY 7 VERIFICATIONS Check before riding for the first time The vehicle has been verified at the Monty factory before to be on sale Nevertheless one should check the following components to be securely fastened before riding the DPIE 4 for the first time Correct position of the front brake lever cable and disc Correct tight of the wheel nuts Correct pressure of the tires Correct wheels align Correct folding security system Correct tight of the quick fastening clamps DPIE 4 does not require any initial kind of lubrication it is prepared to travel the first km without any type of maintenance afterwards the standard maintenance DPIE 4 and its components shall be checked before riding Remember
27. ty product made from the best materials A clear example are our new electric vehicles They provide a new means of light and fun transport which is also ecological silent and does not pollute Suitable to any age by their handy and economical use For this reason we want to thank you for choosing us a decision which will benefit the environment and definitely all of us e Thank you for dedicating few minutes to read this manual We hope to have got a product of your requirement For further information about our products visit our webpage http www monty es A IMPORTANT WARNINGS NON FULFILLMENT OF THE INSTRUCTIONS DETAILED IN THIS MANUAL MAY LEAD TO MECHANICAL FAILURES A LOSS OF CONTROL AND POSSIBLE FALLS WITH SERIOUS PHYSICAL INJURIES TO THE USER OR OTHERS INCLUDING EVEN DEATH INCORRECT USAGE MAY ALSO RISK YOUR PHYSICAL INTEGRITY AND THAT OF OTHERS SAFETY WARNING DO NOT OPEN OR MANIPULATE THE BATTERY DOING SO WILL FORFEIT THE WARRANTY ESTABLISHED IN THIS MANUAL IF YOU OPEN OR MANIPULATE THE BATTERY CHARGER OR ELECTRIC CIRCUIT YOU MAY PROVOKE A SHORT CIRCUIT AND POSSIBLE INJURIES SHOCK OR BURNS WE RECOMMEND YOU TO USE ALWAYS THE HELMET WARRANTY ADVISES MODIFYING THE FRAME FORK OR ANY OTHER COMPONENT IMPLIES THAT THIS VEHICLE NO LONGER CONFORMS TO OUR SPECIFICATIONS AND THEREFORE ANNULS THE WARRANTY MANIPULATING THE ELECTRIC COMPONENTS OF THE VEHICLE WILL ALSO FREE MONTY OF ANY POSSIBLE LIABILITY SH
Download Pdf Manuals
Related Search