Optical Fiber Transmission System VF-10x
Contents
1. 20 1 Introduction 1 1 Check List Check your package for the following parts VF 10x T Video over Fiber Media Converter Transmitter x 1 VF 10x R Video over Fiber Media Converter Receiver x 1 5V 2A Power Adapter x 2 User s Manual x 1 If any of these pieces are missing or damaged please contact your dealer immediately if possible retain the carton including the original packing material and use them again to repack the product in case there is a need to return it to us for repair 1 2 Introduction To Video Over Fiber Converter PLANET Video over Fiber Converter kit consists of a Video Transmitter VF 10x T and a Video Receiver VF 10x R It is a digital fiber optic transmission system which provides customers with a cost effective solution for transmission of one channel uncompressed digital video and one reverse RS485 async data over one single fiber optic cable It is an adjustable device for providing high quality real time video The plug and play design makes the installation more convenient and easier The system can be widely used in intelligent transportation systems ITS traffic surveillance security monitoring automation control intelligent residential districts and so on Typical Applications Intelligent Transportation Systems ITS m Toll Collection Traffic Surveillance 86 Rail Signaling Air Traffic Management2. Perimeter Alarms and Area Monitoring Telemedicine and Teleconference Industrial Surveillance Intelligent Building Key Features Video Data over fiber transmission 8 bit Video Signal digital sampling PAL NTSC SECAM compatible Data Type RS485 Standalone or work with PLANET MC 700 1500 1500R Media Converter Chassis Compact in size wall mount design easy installation 1 4 Product Specifications Model VF 10x KIT Series Video Characteristic Video Channel 1 channel bi direction Signal Mode NTSC PAL Video Connector BNC Video Input Output Impedance 75o0hm unbalanced interface Video Input Output Voltage 1 0 Vpp Typical peak peak value 1 Video Bandwidth 6 5MHz Video Digital Bit Width 8 10 bit Differential Gain DG lt 1 3 typical value Differential Phase DP lt 1 39 typical value SNR Weighted 63 typical value Data Interface Data Channel 1 channel Physical Protocol RS485 Operation Mode Simplex Data Connector 3 pin terminal block with screw clamps Data Rate DC 115 2Kbps Data Distance RS485 0 1200m Bit Error Rate BER lt 10ns Optical Interface VF 101 KIT ST VF 102 KIT FC Optical Connector VF 102SC KIT 5 VF 102S15 KIT SC VF 106 KIT SC WDM VF 101 KIT 2km for multi mode VF 102 KIT 20km for single mode
3. Distance 1025 2km for multi mode VF 102S15 KIT 15km for single mode VF 106 KIT 20km for single mode 101 TX amp RX 1310nm VF 101 KIT VF 101 R TX amp RX 1310nm TX 1310nm 1550 VF 102 KIT TX 1550nm 1330nm VF 102SC T amp RX 1310nm Optical Wavelength VF 102SC KIT VF 102SC R amp RX 1310nm VF 102S15 T amp RX 1310nm VF 102S15 KIT VF 102S15 R amp RX 1310nm TX 1310nm velo RX 1550nm VF 106 KIT TX 1550nm 1330nm VF 101 KIT Max 14 Min 19 VF 102 KIT Max 7 Min 14 VF 102SC KIT 14 Min 19 dBm VF 102S15 KIT 7 20 VF 106 KIT Max 8 Min 14 VF 101 KIT 34 5dBm VF 102 KIT 32dBm Receive Sensitivity 5 dBm VF 102SC KIT 34 5dBm VF 102S15 KIT 28dBm VF 106 KIT 31dBm 98 Input Power dBm VF 101 KIT 14 VF 102 KIT 0 VF 102SC KIT 14 102515 8 VF 106 KIT 0 Cable 50 125um 62 5 125 multi mode cable 9 125 single mode cable Hardware Specification One for Power One for Video LED Indicators Green Link One for Fiber Optic Green Link 94 x 70 x 26 Weight 215g Power Requirement 5V 2A Power Consumption 4 8 watts maximum Mechanical Metal Compatible Convert
4. software configuration Users can immediately use any feature of this product simply by attaching the cables and turning the power on However there are some key limitations on the video over fiber converter as shown below The device is used for Point to Point connection only trans mitter to receiver and allows video and data to work on the same optical fiber patch cord The BNC connector supports 75 ohm cable The maximum distance will change with the quality of coaxial cables 3 2 Stand alone Installation To install a VF 10x T VF 10x R stand alone on a desktop or shelf simply complete the following steps Step 1 Turn off the power of the analog camera monitor to which the VF 10x T VF 10x R will be attached Step 2 10 Transmitter Connect coaxial cable from analog camera to video BNC port of the VF 10x T 14 Step 3 Attach FC single mode fiber cable from VF 10x T to VF 10x R in the remote site Step 4 VF 10x R Receiver Connect coaxial cable from monitor DVR to video BNC port of the VF 10x R Step 5 Connect the 5V DC power adapter to the VF 10x T VF 10x R and verify that the power LED lights up Step 6 Turn the power of the analog camera monitor the video LED green should light up when all cables are attached Coax Upto 20km f Speed Dome VF 10X T VF 10X R Transmitter Receiver Fiber optic Videoline Figure 3 1 VF 10x T VF 10x R standalone i
5. Optical Fiber Transmission System VF 10x KIT User s Manual Trademarks Copyright PLANET Technology Corp 2015 Contents are subject to revision without prior notice PLANET is a registered trademark of PLANET Technology Corp The information in this manual is subject to change without notice All other trademarks belong to their respective owners Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications and makes no warranty and representation either implied or expressed with respect to the quality performance merchantability or fitness for a particular purpose PLANET has made every effort to ensure that this User s Manual is accurate PLANET disclaims liability for any inaccuracies or omissions that may have occurred Information in this User s Manual is subject to change without notice and does not represent a commitment on the part of PLANET PLANET assumes no responsibility for any inaccuracies that may be contained in this User s Manual PLANET makes no commitment to update or keep current the information in this User s Manual and reserves the right to make improvements to this User s Manual and or to the products described in this User s Manual at any time without notice If you find information in this manual that is incorrect misleading or incomplete we would appreciate your comments and suggestions FCC Warning This equipment h
6. as been tested and found to comply with the regulations for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with this user s guide may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense CE Mark Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Energy Saving Note of the Device This power required device does not support Stand by mode operation For energy saving please remove the DC plug or push the hardware Power Switch to OFF position to disconnect the device from the power circuit Without removing the DC plug or switch off the device the device will still consume power from the power source In the view of Saving the Energy and reduce the unnecessary power consuming it is strongly suggested to power off or to remove the DC plug for the device if this device is not intended to be active WEEE Warning To avoid the potential effects on the environment and huma
7. e left side of the VF 10x T VF 10x R that allows the converter to be easily installed with DIN rail mounting PLANET optional DIN rail mounting kit RKE DIN can be ordered separately When the wall mount application needs to be replaced with the DIN rail application for the VF 10x T VF 10x R please refer to the following figures to attach the DIN rail to the converter To hang the VF 10x T VF 10x R on the DIN rail follow the steps below Step 1 Screw the DIN rail on the VF 10x T VF 10x R Step 2 Lightly press and push the DIN rail into the track Step 3 Check whether the DIN rail is tightly on the track You must use the screws supplied with the mounting brackets Damage caused to the parts by using incorrect screws would invalidate your warranty 19 6 4 Power Information The central post of the power jack of the VF 10x T VF 10x R measures 2 5mm and 5VDC power input is required It conforms to the bundled AC DC adapter and Planet s Media Converter Chassis If you have a power connection issue please contact your local sales representative Please keep the AC DC adapter as a spare item when your VF 10x is installed to a Media Converter Chassis 2 5mm gt DC Receptacle 2 5mm 5V for each slot 6 9 DC receptacle is 2 5mm wide that conforms to 2 5mm DC 5 central post of the Video over Fiber Converter Do not install any improper unit on any model of the Video over Fiber C
8. er Chassis MC 700 MC 1500 MC 1500R Standards Conformance Regulatory Compliance FCC Part 15 Class A CE Environment Operating Storage Temperature 0 50 degrees C Relative Humidity 5 95 non condensing Temperature 10 70 degrees C Relative Humidity 5 95 non condensing 10 2 Hardware Description 2 1 Front Panel The units front panels provide a simple interface monitoring the converter There are fiber optic interface and video socket on the front panel For the VF 10x T VF 10x R with reverse data connector the RS485 data port may be connected to the user s interface end VF 102SC T VF 102SC R VF 106 T VF 106 R VF 102S15 T VF 102S15 R 11 1 2 1 1 Ports connection Connect the video signal to or from the Video Connection product through a 75Q coax cable with BNC plug Connect the output data port e g TX and TX of the other controlled device to the RX and RX of the RX Async data Connect the input data port e g RX Connection and RX of the other controlled device to the TX and TX of the TX m GND in both and RX should be connected directly to user s equipment Connect the fiber optic cable pigtail with Fiber Connection FC PC SC PC WDM PC or ST PC optical connector to the product s fiber port 2 1 2 LED Indicators The rich diagnostic LEDs on the front panel can provide the o
9. n health as a result of the presence of hazardous substances in electrical and electronic equipment end users of electrical and electronic equipment should understand the meaning of the crossed out wheeled bin symbol Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately Revision Video over Optical Fiber Media Converter User s Manual For Models VF 10x T VF 10x R Rev 1 2 July 2015 Part No 2350 AA3700 002 Table of Contents 1 6 DST Check 6 1 2 Introduction Video Over Fiber 6 LS Key Features respiron a a 7 1 4 Product 7 2 Hardware Description sicccicisnassccscnsnas cxnvacsansaseanegdacadvensdecaaa 11 2 14 Front Panele 11 2 1 1 556 12 2 4 2 CED 12 2 27 REAP PANE 13 3 Installing THe CONV lt 14 tains 14 3 2 Stand alone Imstallation 14 3 3 Chassis Installation and Rack 16 3 4 Optional DIN rail 18 4 Power INfOMMABON sine
10. nstallation 15 H 3 3 Chassis Installation and Rack Mounting To install the Video over fiber Converter in a 10 inch or 19 inch Converter Chassis with standard rack follow the instructions described below Step 1 Step 2 Place your Converter Chassis on a hard flat surface with the front panel positioned toward your front side Carefully slide in the module until it is fully and firmly fitted into the slot of the Converter Chassis Figure 3 2 Insert a video over fiber converter into an available slot Step 3 Step 4 Step 5 8 16 Attach a rack mount bracket to each side of the Converter Chassis with supplied screws attached to the package After the brackets are attached to the Converter Chassis use suitable screws to securely attach the brackets to the rack Proceed with steps 4 and 5 of Section 3 2 Stand alone Installation to connect the video and fiber cabling and supply power to your Converter Chassis 7122 VF 10X T Media Converter Chassis VF 10X T Coax f Speed Dome VF 10X T Control Keyboard Coax eg es ee Gk x Fiber optic i gt Videoline 00 Serial Line 85485 t Ree art aes Speed Dome VF 10X T Figure 3 3 VF 10x T VF 10x R media converter chassis installation 17 amp 3 4 Optional DIN rail Mounting There are two DIN rail holes on th
11. onverter 8 20
12. perating status of individual port and whole system There are 3 LEDs for POWER VIDEO and LINK on the front panel of TX RX LED Color Function It indicates that the Converter has power POWER Green shear iE VIDEO Green It indicates there is video signal when lit LNK Green It indicates there is laser when lit _4 12 2 2 rear panel of the converter has one DC jack which accepts an input power of 5V DC at 2A 1 The device is a power required device meaning it will not work till it is powered If your gA network should be active all the time please 2 consider using UPS Uninterrupted Power poten Supply for your device to prevent you from Notice network data loss or network downtime 2 In some areas installing a surge suppression device may also help to protect your converter from being damaged by unregulated surge or current to the converter or the power adapter 13 3 Installing The Converter This section describes how to install your VF 10x Media Converter and make connections to the converter Please read the following sections and perform the procedures in the order being presented The hardware installation of PLANET VF 10x Media Converter does not need software configuration To install your VF 10x on a desktop or shelf simply complete the following steps 3 1 Limitation The converter does not require any
Download Pdf Manuals
Related Search