STRINGPROFI 69 STRINGING MACHINE USER`S MANUAL
Contents
1. ICE STRINGPROFI 69 STRINGING MACHINE USER S MANUAL ANATOMY O WON OO tan BW NY PKP WHO PO WN IO HN HN DD N m a Ra pa BF pa pi pa pa SIDAKRHDBNASSCHNADARWNHE S Machine Body along Tension Head Assembly Floor Stand Tennis Swivel Clamp Swivel Clamp Base V Shaped Side Support Center Support Adjustment Knob Side Support Arm Adjustment Knob Mounting Stock Turntable Mounting Stock Locking Knob Rubber Cover Side Support Arm Center Support Turntable Track Tension Head Rail Height Adjustment Knob Brake Tool Tray Reel Holder Column Base Feet String Gripper Tension Locking Lever Tension Display Tension Setting Knob Tension Head Handle Crank Tension Head Housing Stopper ASSEMBLY Step 1 Secure column to foot using 4 long bolts washers and nuts by a 6 mm and a 12 mm wrenches Mount the tool tray on the column with 4 small bolts by a 10 mm wrench Screw the string reel holder into the column Screw the height adjustment knob onto the column but not too deep Step 2 Insert the machine body into the i J xdi BAL y column top and allow to set Adjust the machine body to the desired height and lock in place with the height adjustment knob gt illustration A A height adjustment knob E l Step 3 Unlock the turntable by loosening the brake illustration B B brake2. To turn the machine on press the black POWER KG LB button for 1 second untill a tension appears on the display NOTE the power save function has been set for 2 minutes at factory before shipping so the display will shut down automatically after 2 minutes To motivate the display repeat the procedure step 2 again To turn power off press the black POWER KG LB button for 2 seconds until OFF appears on the display Or wait for 2 minutes till the power save function is motivated and display will shut down automatically as well Step 3 KG LB Button Press the black POWER KG LB button for 0 5 second to change tension display from KG to LB To set tension unit from LB to KG press the black POWER KG LB button for 0 5 second again TENSIONING Step 1 Setting Tension Set the tension by rotating the tension setting knob counter clockwise to increase the tension or clockwise to decrease the tension until the desired tension appears on the display Step 2 Pulling the Strings To pull the string continue rotating the tension head crank handle backward until the tension locking lever clicks out This locks the tension head to the tension rail Step 3 Releasing the Strings To release the string after clamping hold on to tension head and push tension locking lever back up into the catch on the tension head Lift the string out of the string gripper for the next hole TENSION CALIBRATION Step 1 Set t
3. Step 4 Step 5 Insert two string clamps into the string Unlock the tension head by pushing clamp bases and four side supports the tension head by pushing the in the holes of the side support arms tension head locking lever back into catch Rotate the crank handle counter clockwise to slide the tension head to get closed to the racquet mount MOUNTING THE RACQUET FRAME Inserting the Side Supports Insert the side supports into the proper hole on each side support arm and set the side supports at the right angle for mounting the racquet frame Adjusting the Mounting Stocks Loosen both mounting stocks by turning the mounting stock knobs counterclockwise Place the racquet frame properly on both mounting stocks and adjust the distance between the mounting stocks to accommodate the size of the racquet frame Turn both mounting stock knobs clockwise to lock both mounting stocks in position Side Support Adjustment Center Support Adjustment Turn the knobs at Turn the knobs at the upper of each mounting the bottom of each stock clockwise until snug against the racquet mounting stock A M frame and slight resistance is felt clockwise to bring the side supports in the contact with the racquet frame at all four points KEYPAD OPERATING INSTRUCTIONS Step 1 Battery Setting Set one dry battery 9 volts beneath the tension head Caution position and correctly Fi ELS Step 2 Power Button
4. he tension scale on 60 Ibs Place a string attached to a tension calibrator in string gripper Tension calibrator will indicate the pounds of tension on tension head under actual stringing conditions Pull string until the locking lever releases If it releases before 60 Ibs or after 60 Ibs the following adjustment is needed CAUTIION Be sure to release string holding tension calibrator You are now ready for adjustment Step 2 Loosen the safety screw A If the locking lever release before 60 Ibs turn the adjustment screw B counterclockwise until the scale reading matches the calibrator s if the locking lever release after 60 Ibs turn the adjustment screw B clockwise WARNING Be sure to tighten the safety screw A after the adjustment has been made SWIVEL CLAMP OPERATION Different strings and different gauges require different adjustments Adjustment can usually be done by finger tips Note that the handle of the swivel clamp should be lifted before adjustment SWIVEL CLAMP BASE OPERATION The lever on the swivel clamp base is turned clockwise to lock the base To unlock the lever s turned counterclockwise If the swivel clamp base doesn t lock well to the turntable or the locking angle of the lever of the clamp base is too big you may adjust the nut beneath the clamp base by a 17 mm wrench clockwise or counterclockwise Closed Position Open Position HOLE FINDER OPERATION Use a hole finder to create a pathway be
5. tween or around strings and through tight grommets Insert the awl through the grommet hole and pull the handle of the awl outward leaving the outer sheath in the grommet hole Insert the end of the string into the sheath FLAT NOSE PLIERS OPERATION TENNIS AWL OPERATION DIAGONAL CUTTER PLIERS OPERATION 11
Download Pdf Manuals
Related Search