GSD USB Fingerprint Enrolment Reader
Contents
1. conditions and placing a finger on the sensor window will not operate the Door Control To re activate the Scan Sensor press any key before placing the finger Default Door Exit Door Interlock Interlock Alarm Page 5 on the Sensor window Button Contact I P O P Buzzer W iring Diagrams Sy Operation Instructions Enrolling and Removing Users SAA ron Finger Print Switch is mounted to pattress box using secutity Enrol a User Fingerprint screws provided Both Security Caps are Remove a User Fingerprint then clipped onto Finger Print Flush Mounting Switch Example To Enrol a Users Fingerprint in User Location 22 Code 1 User Loc 22 Amber LED flashes Red LED flashes Red LED flashes oe ge Present Finger Present Finger to Enroll to Enroll Note Refer to pages 6 amp 7 for correct incorrect finger placement To enrol a users fingerprint the users finger must be presented twice to the Scansensor window The scan sensor must get 2 good quality readings to have a successful enrolment As per the steps above present the finger to the sensor window until confirmation beep is heard and Red Led turns off momentarily Remove and re present the finger for the second time to complete the enrolment A successful enrolment will be followed by an Access Granted Tone Amber LED flashes Red LED flashes Amber LED flashes To re attach Security Caps simply align tabs into holes as shown above a2. Other products from GSD global security devices GSD Wi Enterprise Wi Plus System is the next generation in access control solutions It provides a Wireless Network throughout the premises giving the convenience and security of a fully networked system for a fraction of the cost Features 2 Best Practices ED Wiring Diagrams PD Installation Diagrams ED Finger Placement WD For more information on the Wireless Network System visit our website Operation Instructions ED www globalsecurity ie Administration Notes D global security devices Finger Print Switch Finger Reference Note Users are enrolled to the User Locations defined in the table above only Other products from GSD global security devices GSD Wi Enterprise Wi Plus System is the next generation in access control solutions It provides a Wireless Network throughout the premises giving the convenience and security of a fully networked system for a fraction of the cost Features 2 Best Practices ED Wiring Diagrams PD Installation Diagrams EED Finger Placement WD For more information on the Wireless Network System visit our website Operation Instructions ED www globalsecurity ie Administration Notes FX global security devices Finger Print Switch Technical Specs Current consumption with load max 5 Amps 240V ac 20 C to 60 C Features Controls 1 Door 35 Users Door Monitoring via Door C
3. default Engineer code 6666 immediately This will restore the factory settings Wiring Diagrams Operation Instructions Be Changing Engineer Code Important ae Description Always fit the varistor supplied Sounder 4 Changing the Engineer Code with the unit between the lock terminals as shown Door Example To Change the Engineer Code to 1234 Exit Button Enter Engineer t Amber LED flashes Red LED flashes Amber LED flashes Varistor s 4 LI amp Door MagLock Always connect a a ar varistor between a ra Code Description ee i 6 Changing Backlight Silent or Scan Mode the NC for a maglock w M Changing Settings Example To Toggle the Backlight to Always On or Only On after a Key 12V Linear Press Power supply Ly ae Enter Engineer Code 6 G Amber LED flashes Red LED flashes Amber LED flashes Example To Toggle the Silent Operation On Off r Enter E Interlock IP on 2nd Door Amber LED flashes Red LED flashes Amber LED flashes Interlock IP from _ 2nd Door am S ae Example To Toggle the Sensor Scanning Mode to Always On Off Enter Note All OV shown in the diagram are connected a f Engineer Code 6 to OV at the back of the keypad terminal block N N OP SEE OER ONIY SIN 2A SEAC SUDEN ar T Amber LED flashes Red LED flashes Amber LED flashes Note If Sensor Scanning M ode is set to Off the Red Sensor light will be off in normal standby
4. nd ease the Caps back into place using a flat bladed screwdriver Description Changing the Relay Time To release Security Caps pusha Example To Change the Relay Time to 15 seconds EE 4 flat bladed screwdriver into slots on the side and pull forward gently Code 3 Seconds 15 EnS Present Finger Amber LED flashes Red LED flashes Red LED flashes to Confirm Finger Placement Correct Finger Placement Incorrect Finger Placement Correct Incorrect Note Ensure that the finger is centered and Note Incorrect placement finger does not placed flat to the surface and fully covers the fully cover the sensor window sensor window The door control will not respond and the red light will not turn off if the sensor window Note Finger must remain on the sensor is not fully covered by the finger window until the door control acknowledges that the finger has been scanned by sounding a beep and turning off the red light This will take approximately 1 second
5. ontact Tamper Resistant Easy Programming Programmable Settings Programming Code Relay Active Time Silent or Audible Operation Keypad Backlight Scan Mode Inputs Outputs Options Indoor Outdoor Use IP 65 Robust Polycarbonate Housing Mounts onto Standard Electrical Patress Box Note Engineering mode status Led indicators Amber Led flashing indicates that the unit is in Engineering mode Red Led flashing indicates user needs to enter data or present finger Present a finger at any stage to exit engineering mode Otherwise it will time out automatically 2 a SF ee Ee ee a ee User Location Finger Reference Note Users are enrolled to the User Locations defined in the table above only Best Installation Practice 1 Always Default the Door Control to Factory Settings before ae a 2 It is important to ensure that the varistor supplied with the Door cote aces tetasteriatana ins Finger Reference Factory Default PIN codes The following PIN codes are the Factory Default Settings The Default Engineer code is 6666 User PIN 1111 Note The User PIN 1111 is deactivated when the first User is added to the keypad Restoring Factory Settings Restoring Factory Default Settings Example To Restore Factory Default Settinas Present Finger to Confirm Note If programming code is lost Remove the Security Caps see page 4 and hold down the 5 key during power up and enter the
Download Pdf Manuals
Related Search