Home

Autodome 7000 Series Operation Manual

1. Wiring the Fiber Optic Model If installing a Fiber Optic model follow these steps Notice Refer to the Connection page 71 chapter for fiber optic specifications For instructions on installing a fiber optic module into a power supply box see the VG4 Fiber Optic Media Converter Installation Guide that ships with the module Bring the fiber optic cable item 3 in the figure below into the right side of the power supply box Connect the fiber optic cable to the port for the SFP module item 2 in the figure below Connect the RJ45 plug of the cable to the RJ45 socket item 1 in the figure below on the fiber optic module in the power supply box Route the control wires from the Power Supply to the Pipe Interface Board Then attach the supplied six 6 pin control data connector to the wires in the Power Supply Box Refer to Wire the Pipe Interface Board page 52 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Installing the Roof Parapet and Pipe Mounts en 45 Figure 9 3 Fiber Optic Ethernet Module installed 1 RJ45 Ethernet socket 2 Port for SFP module sold separately 3 Fiber Optic cable user supplied Power Supply Box Connections The following figure is a detailed illustration of the Roof or Pipe Mount Power Supply Box which includes the fuse specifications Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 2
2. VA Watts 14 AWG 16 AWG 18 AWG 2 5 mm 1 5 mm 1 0 mm HD models with IVA Indoor 35 19 99 m 325 ft 62 m 205 ft 39 m 129 ft HD models with IVA Outdoor 60 55 58 m 190 ft 36 m 119 ft 23 m 75 ft 11 3 Ethernet Connections The camera connects to a 10 Base T 100 Base TX network either directly or via a hub Video optional audio input optional audio output and control are transmitted over a standard TCP IP network using the built in Web server In addition power can be supplied over the Ethernet cable using the Bosch High PoE 60W midspan sold separately Power can also be supplied over the Ethernet cable to in ceiling models and indoor outdoor pendant models used in indoor applications where the heater is not powered using PoE PSEs midspan switches compliant with the IEEE 802 3at class 4 standard The camera can be connected simultaneously to a 24 VAC power supply and to a High PoE 60 W midspan The camera uses power from the 24 VAC power supply If this power supply fails the camera seamlessly switches power input to the High PoE 60 W midspan The camera switches back to the 24 VAC power supply once power is restored Refer to Using the IP Interface for instructions on configuring an IP environment Warning BOSCH High PoE or PoE 802 3at Use only approved High PoE or PoE 802 3at devices For outdoor pendant applications that require heater power use only the Bosch High PoE midspan sold separately
3. 14 3 Password The camera is generally protected by a password to prevent unauthorized access to the unit You can use different authorization levels to limit access 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Configuration via IP Advanced Mode en 89 Notice Proper password protection is only guaranteed when all higher authorization levels are also protected with a password If a live password is assigned for example a service and a user password must also be set When assigning passwords you should therefore always start from the highest authorization level service and use different passwords Password The camera operates with three authorization levels service user and live The highest authorization level is service After entering the correct password you can access all the functions of the camera and change all configuration settings With the user authorization level you can operate the unit and also control cameras for example but you cannot change the configuration The lowest authorization level is live It can only be used to view the live video image and switch between the different live image displays You can define and change a password for each authorization level if you are logged in as service or if the unit is not password protected Enter the password for the appropriate authorization level here Confirm password In each case enter the new
4. Connect the incoming relay contact wires to the mating connector Then reattach the mating connector to the Relay Contacts cable Attach an RJ45 plug to the incoming UTP cable Connect the incoming RJ45 video connector installed previously to the UTP Video Ethernet cable cable 5 Connect the outgoing alarm wires to the flying leads coming from the 4 pin Alarm Outputs cable cable 6 Connect the incoming alarms wires to the flying leads coming from the 6 pin Alarm Inputs cable cable 7 Connect the incoming serial communication wires to the 6 pin mating connector supplied with the VGA PEND WPLATE kit Refer to the Power Supply Box Connections table above for details Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 38 en Installing the Pendant Arm Wall Corner and Mast Pole Mounts AUTODOME 7000 14 Attach the 6 pin serial communication mating connector to the Serial Communications cable cable 8 15 Connect the Earth ground wire if available to the crimp ring terminal inside the Mounting Plate Note The Earth ground is not provided with the VGA PEND WPLATE kit it is a ground connection made at the installed location 16 After making the harness connections to the Mounting Plate rotate the Pendant Arm to close and tighten the two 2 captive screws to 10 12 N m 90 105 in Ibs Notice After all wiring is complete close the cover door and tighten the two 2 captive scr
5. to the left of the scene name indicates the scene is part of the preposition tour 6 To delete a scene from the list select the scene and click the Delete scene X button 7 To overwrite an existing scene Click the View Control link to access the PTZ controls Ol ee tS Use the PTZ controls to navigate to the new scene Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 106 en Configuration via IP Advanced Mode AUTODOME 7000 14 19 14 20 14 21 14 22 Click the scene in the Preposition list you want to overwrite Click the Overwrite scene button to apply the new scene to the existing preposition To change the name of the scene double click the scene in the list Then change the name in the Edit Scene dialog box and click OK 8 To view a scene in the preview window select the scene in the list and click the Show scene button 9 To view a scene from the LIVE page Click a scene number below the PTZ controls on the View Control tab OR Use the keypad and the Show Shot button on the Aux Control tab To define a preposition tour 1 Create the individual scenes By default all scenes in the Preposition list are in the preposition tour 2 To remove a scene from the tour select the scene in the list and uncheck the Include in standard tour box 3 Select a dwell time from the Standard preposition tour drop down list 4 To start the preposition tour Return to the LIVE page
6. Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 100 en Configuration via IP Advanced Mode AUTODOME 7000 14 14 Privacy Masks Privacy Masking is used to block out a specific area of a scene from being viewed Masks can be configured as a gray area with four corners You may define a total of 24 privacy masks To add a privacy mask to a scene 1 Navigate to the scene in which you want to apply a privacy mask Click the View Control link Use the PTZ controls to view the scene 2 Select the privacy mask number to apply to the scene 3 The preview window displays a gray rectangle in the scene 4 Click the Enabled check box to activate the privacy mask 5 The privacy mask in the preview window changes to orange to indicate that the mask will appear in the video streams on the LIVE page 6 Place the cursor inside the privacy mask area in the preview window then click and drag to move the privacy mask 7 Place the cursor on a corner or on a vertex of the mask rectangle then click and drag to expand or shrink the privacy mask area 8 Click Set to save the privacy mask size and position An image window displays the privacy mask 9 To hide an individual mask select the mask number and clear the Enabled check box 10 To hide all masks from an image view click the Disable Masks check box Note If you choose to hide all masks you must enable each individual mask to show the mask in th
7. Figure 9 1 VG4 A PSU1 or VG4 A PSU2 Power Supply Box AUTODOME 7000 i 120 VAC 230 VAC Power In 6 Control Wire Used for Audio input and output in AUTODOME 7000 Series 2 P101 Connector 7 24 VAC Power Out 3 Ground Connection 8 P107 Connector 4 Transformer 9 Earth grounded conduit with power input and earth ground connection 5 Ethernet Wire 10 Earth grounded conduit with Ethernet video control audio input and output to head end system 11 Earth grounded conduit to camera Method Two is to bypass the Power Supply Box and route the video control and alarm wires directly to the Interface Board You connect only the power wires inside the Power Supply Box All conduit and junction boxes used must be electrically earth grounded 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Installing the Roof Parapet and Pipe Mounts en 43 Figure 9 2 VG4 A PSU1 or VG4 A PSU2 Power Supply Box Connected to Pipe Interface Board VG4 A PSU1 VG4 A PSU2 Pipe Interface Board 1 120 VAC 230 VAC Power In 7 P101 Connector 2 P101 Connector 8 P107 Connector 3 Ground Connection 9 24 VAC Power In to camera 4 Transformer 10 Earth Ground 5 24 VAC Power Out 11 24 VAC Power In to camera 6 P107 Connector 12 24 VAC Power In to Heater 13 24 VAC Power In to Heater 14 Camera Power 15
8. If the Intelligent Tracking feature is set to Auto or Click the live video image displays an eye icon with a symbol that conveys the state of Intelligent Tracking activity Graphic Description Explanation White eye flashing Intelligent Tracking is actively following a target Gray eye with a red X Intelligent Tracking lost the selected target and will wait for the target to reappear using the last known trajectory During the IDLE state the camera will not seek other objects in motion Gray eye without a symbol Intelligent Tracking is idle waiting to track a target Gray eye with a pause Intelligent Tracking attempts to track a symbol target passively while a user has camera control Tracking triggered by IVA rules 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 15 3 Operation en 141 In this mode the camera continuously analyzes the scene for IVA alarms or IVA rule violations If an IVA rule is violated it triggers the advanced tracking feature of the camera to start following the object person that triggered the alarm This allows the camera to track moving objects of interest without getting distracted by other moving objects in the scene To activate this mode you must enable IVA by selecting either IVA 5 6 or IVA 5 6 Flow in the Analysis type field of the VCA page from the SETTINGS page select Advanced Mode gt A
9. Problem Questions to Ask Actions to Resolve the Problem Picture is dark Check that the Gain Control is set to High via the Settings menu If O K then Check that the Auto Iris Level is set to the appropriate level via the Settings menu If O K then Check that the camera lens cover is removed If O K then Check that the maximum Ethernet cable distance has not been exceeded If O K then Restore all camera settings via the Settings menu Background is too Turn on backlight compensation via the Settings menu or by using 20 Aux bright to see subject ON OFF Video is rolling noisy Check the frequency or distorted From the SETTINGS page click Advanced Mode Click Camera and then click Installer Menu In the Base frame rate field choose either 25 ips or 30 ips Check the integrity of all connectors and splices of the Ethernet cable If O K then Contact Bosch Technical Support Loss of Privacy when Webbrowsers BVC or BVMS using Privacy Mask Press the FindHome key on the Special Functions menu in order to align the mask back to the original position Intuikey when keyboard is connected to BVC or BVMS Issue a SetScene 110 command in order to align the mask back to the original position No Network Check all network connections Connection Ensure that the maximum distance between any two Ethernet connections is 100 m 328 ft or les
10. 2 0 F 01U 283 679 92 en Configuration via IP Advanced Mode AUTODOME 7000 14 6 14 7 Enter the interval in seconds between insertions of the digital signature Advanced Mode Web Interface Appearance On this page you can adapt the appearance of the web interface and change the website language to meet your requirements If necessary you can replace the manufacturer s logo top right and the product name top left in the top part of the window with individual graphics Notice You can use either GIF or JPEG images The file paths must correspond to the access mode for example C Images Logo gif for access to local files or http www mycompany com images logo gif for access via the Internet Intranet When accessing via the Internet Intranet ensure that a connection is always available to display the image The image file is not stored in the camera Website language Select the language for the user interface here Company logo Enter the path to a suitable graphic if you want to replace the manufacturer s logo The image file can be stored on a local computer in the local network or at an Internet address Device logo Enter the path to a suitable graphic if you want to replace the product name The image file can be stored on a local computer in the local network or at an Internet address Notice If you want to use the original graphics again simply delete the entries in the Company logo and Dev
11. Click the Aux Control tab Type 8 in the input box and click the Aux On button 5 To stop the tour type 8 and click the Aux Off button Sectors Sector The camera s pan capability is 360 and is divided into 16 equal sectors This section allows you to apply a title for each sector and to designate any sectors as a Blanked Sector To define a title for sectors 1 Place the cursor in the input box to the right of the sector number 2 Type a title for the sector up to 20 characters long 3 To blank the sector click the check box to the right of the sector title Miscellaneous Fast address This parameter allows the appropriate camera to be operated via the numerical address in the control system Enter a number between 0000 and 9999 inclusive to identify the camera Note This is required for identifying cameras connected through a decoder such as the VIDEOJET decoder 3000 VJD 3000 Logs To save the log file information 1 Click Download to obtain the log information 2 Click Save 3 Navigate to the directory in which you want to store the log information 4 Type a name for the log file and click Save Audio You can set the gain of the audio signals to suit your specific requirements The current video image is shown in the small window next to the slide controls to help you check the audio source and improve assignments Your changes are effective immediately 2014 04 2 0 F 01U 283 679 Operation M
12. Description Pin Description Pin Description 1 Alarm Out 1 1 Alarm in 3 1 Alarm Out 4 Normally Open 2 Alarm Out 2 2 Alarm in 4 2 Alarm Out 4 COM 3 Alarm Out 3 3 Alarm in 5 3 Alarm Out 4 Normally Closed 4 Alarm Ground 4 Alarm in 6 4 Earth Ground 5 Alarm in 7 5 Analog Alarm 1 6 Alarm Ground 6 Analog Alarm 2 7 Ground For in ceiling mount only Low Voltage TTL 3 3V can also be used gt Power Supply Box Connections The following figure is a detailed illustration of the Pendant Arm Power Supply Box which includes the fuse specifications If you are connecting supervised alarms and relays attach the supplied 7 pin Relay Connector to the appropriate incoming wires Refer to Make Connections in the Power Supply Box page 33 for additional information 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Installing the Pendant Arm Wall Corner and Mast Pole Mounts en 27 Figure 8 2 Pendant arm power supply box 1 Ground Screw 7 P101 Connector Power In 120 VAC 220 VAC 2 From Harness Nexus cable bundle 8 P106 Connector Control In Out for external audio input and output 3 In Out 1 2 in 15 mm NPS Fitting 9 P105 Connector Audio to camera 4 Ethernet connector 10 Power In 3 4 in 20 mm NPS Fitting 5 P107 Connector 24 VAC to camera 11 Audio Input Output 3 4 in 20 mm NPS Fitting labeled SERIAL COM
13. MAC address and must be appropriately set up so that once an IP address is assigned it is retained each time the system is rebooted IP address Enter the desired IP address for camera in this field The IP address must be valid for the network Subnet mask Enter the appropriate subnet mask for the selected IP address here Gateway address If you want the unit to establish a connection to a remote location in a different subnet enter the IP address of the gateway here Otherwise leave the box as 0 0 0 0 13 4 Basic Mode Encoder 13 5 Basic Mode Audio You can set the gain of the audio signals to suit your specific requirements The current video image is shown in the small window next to the slide controls to help you check the audio source and improve assignments Your changes are effective immediately If you connect via Web browser you must select the option Transmit Audio on the LIVE Functions page See L VE Functions page 93 For other connections the transmission depends on the audio settings of the respective system Audio The audio signals are sent in a separate data stream parallel to the video data and so increase the network load The audio data are encoded according to G 711 and require an additional bandwidth of approx 80 kbps per connection in each direction If you do not want any audio data to be transmitted received select Off Line In You can set the line input gain using the slider Values range from O
14. Record Allows configuration for the recording options of the IP module You can record video from the LIVE page to a hard drive or to a customer provided SD card Playback Allows playback of stored video from a customer provided SD card Models with the 30x optical zoom have additional features including the following Anti fog feature Significantly improves visibility when viewing foggy or other low contract scenes Intelligent Dynamic Noise Reduction iDNR IVA VCA controls the iDNR feature which reduces noise based on motion activity in the scene When there is no motion in the preset scene noise reduction is increased When the camera detects motion in the preset scene noise reduction is decreased to reduce bandwidth and optimize storage space Image Stabilization This feature allows the camera to detect continuous vibration If it detects vibration the camera dynamically corrects the shaky video in both the vertical and horizontal axis resulting in exceptional image clarity and a stable field of view on the monitor Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 18 en Planning information AUTODOME 7000 Planning information 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 4 Pre installation Checklist en 19 Pre installation Checklist 1 Determine the location and distance fo
15. Standard with JPEG E mail with attached JPEG image file SMS E mail in SMS format to an e mail to SMS gateway for example to send an alarm by cellphone without an image attachment Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 120 en Configuration via IP Advanced Mode AUTODOME 7000 Caution When a cellphone is used as the receiver make sure to activate the e mail or SMS function depending on the format so that these messages can be received You can obtain information on operating your cellphone from your cellphone provider Image size Select the appropriate image size Small Medium Large 720p 1080p Attach JPEG from camera Click the checkbox to specify that JPEG images are sent from the camera An enabled video input is indicated by a check mark Destination address Enter the e mail address for alarm e mails here The maximum address length is 49 characters Sender address Enter a unique name for the e mail sender for example the location of the device This will make it easier to identify the origin of the e mail Note The name must include at least two character groups separated by a blank for example Parking Garage in order for the system to generate an email from that name as in From Parking Garage Text with only one group of characters for example Lobby will not generate an email Test e mail You can test the e mail function by clicking the Send Now
16. The following table summarizes the pin connectors and their function No Connector Pini Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 P103 Alarms In Alarm 3 Alarm 4 Alarm 5 Alarm 6 Alarm 7 AGND P102 Alarms Out Alarm 1 Alarm 2 Alarm 3 GND P104 Analog Relay Relay N O Relay Relay N C Earth Alarm 1 Alarm 2 Ground COM P101 24 VAC Line Earth Neutral P105 SERIAL CODE CODE Earth GND RXD TXD Signal COMMUNI Audio IN Audio IN Ground Audio OUT Audio GND CATIONS Audio in Audio OUT Ground signal Audio out ground signal ground J101 Ethernet Connector Input Table 10 1 Interface Box Wire Terminals Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 64 en Installing the In Ceiling Mount AUTODOME 7000 Notice Pins for P105 1 2 4 and 5 are used for audio input and output for AUJTODOME 7000 Series cameras however their labels are still those of previous versions of analog AUTODOME cameras Warning 24 VAC Class 2 power supply only 9 7 Installing the Ceiling IP54 Housing Gasket In order to conform to the IP54 rating you must install the ceiling gasket illustrated along with the other pieces that protect the camera and provide the IP54 rating in the figure below In addition if you are using the optional black trim ring instead of the factory installed white trim ring the trim ring gasket must also be i
17. Advanced Mode Web Interface 92 Appearance 92 LIVE Functions 93 Logging 94 Advanced Mode Camera 94 Installer Menu 94 Encoder Profile 96 Encoder Streams 98 Privacy Masks 100 Picture Settings 100 Lens Settings 103 PTZ Settings 104 Scenes and Tours 105 Sectors 106 Miscellaneous 106 Logs 106 Audio 106 Pixel Counter 107 Advanced Mode Recording 107 Storage Management 107 Recording Profiles 109 Maximum Retention Time 110 Recording Scheduler 111 Recording Status 112 Advanced Mode Alarm 112 Alarm Connections 112 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 14 32 14 33 14 34 14 35 14 36 14 37 14 38 14 39 14 40 14 41 14 42 14 43 14 44 14 45 14 46 14 47 14 48 14 49 14 50 14 51 14 52 14 53 14 54 14 55 15 15 1 15 2 15 3 16 17 18 19 Table of Contents en 5 VCA 114 Virtual Masks 118 Audio Alarm 118 Alarm E Mail 119 Alarm Task Editor 120 Alarm Rules 120 Advanced Mode Interfaces 121 Alarm Inputs 121 Alarm Outputs 121 Advanced Mode Network 122 Network Access 122 DynDNS 124 Advanced 125 Network Management 125 Multicast 126 Image Posting 127 Accounts 128 IPv4 Filter 128 Encryption 128 Advanced Mode Service 129 Maintenance 129 Licenses 130 Diagnostics 130 System Overview 130 Operation 131 Using the AUTODOME Camera 131 Using Intelligent Tracking 139 Recommended Use of Your Camera 141 Troubleshooting 144 Maintenance 146 Tec
18. Heater Power Wiring the Power Supply Box Notice Refer to the Connection page 71 chapter for wire specifications and distances gt Route the high voltage 115 230 VAC lines through the earth grounded conduit fitting on the left side of the box Notice The Power Supply Box with transformer comes with a barrier that separates the high voltage side on the left from the low voltage 24 VAC side on the right Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 44 en Installing the Roof Parapet and Pipe Mounts AUTODOME 7000 1 Cut and trim the high voltage 115 230 VAC power and ground wires with sufficient slack to reach their connector terminal in the box but not so long as to be pinched by or to obstruct closing the Cover Door 2 Attach the supplied 3 pin Power Plug to the incoming high voltage power wires in the box Refer to connector P101 in the Power Supply Box Connections section below 3 Route the Ethernet cable out to where the camera will be mounted 4 Route the low power 24 VAC wires from the right side of the Power Supply Box out to where the camera will be mounted Attach the supplied 5 pin 24 VAC Dome plug to the wire ends inside the box Refer to connector P107 in the Power Supply Box Connections section below Notice All video control and alarm wires either pass through the Power Supply Box or by pass it and connect directly to the Pipe Interface Board
19. The camera name makes the task of administering cameras in larger video monitoring systems easier for example using the BVC or Bosch Video Management Systems Programs Enter a unique unambiguous name for the camera in this field You can use both lines for this Do not use any special characters for example amp in the name Special characters are not supported by the system s internal management You can use the second line for entering additional characters these can be selected from a table 1 Click the icon next to the second line A new window with the character map is opened 2 Click the required character The character is inserted into the Result field 3 Inthe character map click the lt lt and gt gt icons to move between the different pages of the table or select a page from the list field 4 Click the lt icon to the right of the Result field to delete the last character or click the X icon to delete all characters 5 Now click the OK button to apply the selected characters to the second line of the Camera 1 parameters The window will close Camera ID Each device should be assigned a unique identifier that can be entered here as an additional means of identification Initiator extension Add text to an initiator name to make identification easier in large iSCSI systems This text is added to the initiator name separated from it by a full stop You can see the initiator name in the System Overview page
20. amplified speaker with line level input Audio Line Input Specifications The following Line Input specifications should be complied with in all cases Max Input Voltage 1 Vrms Impedance 9 K Q typical Shield Bare copper braid 95 coverage Internal gain level adjustment is available in case the signal level is too low Audio Line Output Specifications The following Line Output specifications should be complied with in all cases Typical Output 1 Vrms Voltage Impedance 1 5 K Q typical Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 78 en Connection AUTODOME 7000 Shield Bare copper braid 95 coverage Internal gain level adjustment is available in case the signal level is too low Wire Specifications Wire Type Shielded Coax recommended Distance Typically 10 m 33 ft but depends on the signal level Gage Typically 22 AWG to connector P105 P106 but depends on the style of connector used Shield Bare copper braid 95 coverage Center Stranded bare copper conductor Note that long distances are more susceptible to introducing noise into the signal Audio Line Level Input Connections 1 Remove the 100 Ohm termination resistor from the C to C terminals 2 Connect the audio line level source to the Audio_In C input terminal 3 Connect the audio signal ground to the Audio_In C input t
21. d rale des communications des tats Unis FCC Ces contraintes sont destin es fournir une protection raisonnable contre les interf rences nuisibles quand l appareil est utilis dans une installation commerciale Cette appareil g n re utilise et met de l energie de fr quence radio et peut en cas d installation ou d utilisation non conforme aux instructions g n rer des interf rences nuisibles aux communications radio L utilisation de ce produit dans une zone r sidentielle peut provoquer des interf rences nuisibles Le cas ch ant l utilisateur devra rem dier ces interf rences ses propres frais Au besoin l utilisateur consultera son revendeur ou un technicien qualifi en radio t l vision qui proc dera une op ration corrective La brochure suivante publi e par la Commission f d rale des communications FCC peut s av rer utile How to Identify and Resolve Radio TV Interference Problems Comment identifier et r soudre les probl mes d interf rences de radio et de t l vision Cette brochure est disponible aupr s du U S Government Printing Office Washington DC 20402 tats Unis sous la r f rence n 004 000 00345 4 Disclaimer Underwriter Laboratories Inc UL has not tested the performance or reliability of the security or signaling aspects of this product UL has only tested fire shock and or casualty hazards as outlined in UL s Standard s for Safety for Information Technology E
22. page 128 page Image size Select the size of the images that you want to save Small Medium Large 720p 1080p File name You can select how file names will be created for the individual images that are transmitted Overwrite The same file name is always used and any existing file will be overwritten with the current file Increment A number from 000 to 255 is added to the file name and automatically incremented by 1 When it reaches 255 it starts again from OOO Date time suffix The date and time are automatically added to the file name When setting this parameter ensure that the unit s date and time are always correctly set Example the file snap011005 114530 jpg was stored on October 1 2005 at 11 45 and 30 seconds Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 128 en Configuration via IP Advanced Mode AUTODOME 7000 Posting interval Enter the interval in seconds at which the images will be sent to an FTP server Enter O zero if you do not want any images to be sent Target Select the target the name of the account on the server to which to save images Enable Click this checkbox to enable face detection File format Select the file format in which to save images Options are JPEG default YUV420 TIFF Target Select the target the name of the account on the server to which to save images Timeouts Select the number of timesouts for image po
23. 4 Bar Clips 1 Use the bracket Base Plate as a template or cut a holesize hole in the center of the ceiling tile with a drywall utility saw or jig saw Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 60 en Installing the In Ceiling Mount AUTODOME 7000 Figure 10 2 Cut Hole in Ceiling Tile 2 Tighten the four 4 securing screws to the Bracket Assembly N Figure 10 3 Tighten Bracket Securing Screw 3 Secure the Bracket Assembly to an overhead securing point with a safety wire Figure 10 4 Secure Bracket Assembly 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Installing the In Ceiling Mount en 61 9 5 Wire the Interface Box The Interface Box can be wired through the top or side Use the supplied rubber plug to seal the hole which will not be used to route wires Figure 10 5 Interface Box Connections After routing all video control power and alarm wires 1 Attach a 3 4 inch NPS 20 mm conduit fitting to the hole in which you bring in the wires Be sure to thread the inside nut to the conduit fitting 2 Route the video control power and alarm wires through the conduit fitting and into the Interface Box 3 Cut and trim the wires allowing for sufficient slack to their respective terminals in the box Notice If installing the camera to a drywall ceiling allow enough wire to make the con
24. 4 Important Safety Instructions Read follow and retain for future reference all of the following safety instructions Heed all warnings on the unit and in the operating instructions before operating the unit 1 Cleaning Unplug the unit from the outlet before cleaning Follow any instructions provided with the unit Generally using a dry cloth for cleaning is sufficient but a moist fluff free cloth or leather shammy may also be used Do not use liquid cleaners or aerosol cleaners 2 Heat Sources Do not install the unit near any heat sources such as radiators heaters stoves or other equipment including amplifiers that produce heat 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 10 Ih 12 Safety EN en 7 Ventilation Any openings in the unit enclosure are provided for ventilation to prevent overheating and ensure reliable operation Do not block or cover these openings Do not place the unit in an enclosure unless proper ventilation is provided or the manufacturer s instructions have been adhered to Object and liquid entry Never push objects of any kind into this unit through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electrical shock Never spill liquid of any kind on the unit Do not place objects filled with liquids such as vases or cups on the unit Lightning For added protection during a lightning
25. 7000 Series AUDIO IN Audio in signal ground 2 Biphase C For AUTODOME 7000 Series AUDIO IN 3 Earth Ground 4 RxD For AUTODOME 7000 Series AUDIO OUT 5 TxD For AUTODOME 7000 Series AUDIO OUT Audio out signal ground 6 Signal Ground 7 Alarms In EOLR P104 AWG 7 Ground Supervised 1 2 26 16 6 Alarm 2 5 Alarm 1 4 Earth Ground 8 Relay Output P104 AWG 3 Normally Closed R 2 Common 1 Normally Open g Dome Power P101 AWG 3 Dome 24 VAC eo 2 Earth Ground 1 Dome 24 VAC 10 Heater Power P107 AWG 2 Heater 24 VAC 18 14 1 Heater 24 VAC 11 RJ45 Ethernet J101 12 To camera 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Installing the Roof Parapet and Pipe Mounts en 55 The Pipe Interface Board contains all of the connectors for control data image and power wires Follow the procedures below to make the proper connections Warning Use a 24 VAC Class 2 power supply only 1 Attach an RJ45 connector plug to the Ethernet cable and connect the plug to its mating connector J101 on the Pipe Interface Board 2 Attach the control data in out wires to their respective terminals on the P105 connector on the Pipe Interface Board 3 Connect the 24 VAC power wires to the P101 connector on the Pipe Interface Board If this model has a heater connect the 24 VAC heater power wire
26. Click one of the entries in the submenu The web browser opens the corresponding page Making Changes Each configuration screen shows the current settings You can change the settings by entering new values or by selecting a predefined value from a list field Not every page has a Set button Changes to pages without a Set button are set immediately If a page does show a Set button you must click the Set button for a change to take effect Caution Save each change with the associated Set button Clicking the Set button saves the settings only in the current field Changes in any other fields are ignored Some changes only take effect after the unit is rebooted In this case the Set button changes to Set and Reboot 1 Make the desired changes Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 84 en Configuration AUTODOME 7000 2 Click the Set and Reboot button The camera reboots and the changed settings are activated 12 3 Configuring Audio Optional Enabling Audio Transmission To transmit audio via the IP connection follow these steps 1 2 3 4 Open the LIVE page and then click the Settings tab In the left pane click Advanced and then click Web Interface The Web Interface menu expands Click LIVE Functions The LIVE Functions page appears Click the Transmit Audio radio button to enable for audio Activating Audio Reception To configure audio via the Web browse
27. Directive 2002 96 EC Environmental statement Bosch has a strong commitment towards the environment This unit has been designed to respect the environment as much as possible Electrostatic sensitive device Use proper CMOS MOS FET handling precautions to avoid electrostatic discharge NOTE Wear required grounded wrist straps and observe proper ESD safety precautions when handling the electrostatic sensitive printed circuit boards and when inserting into or removing the SD card from the SD card slot Fuse rating For security protection of the device the branch circuit protection must be secured with a maximum fuse rating of 16A This must be in accordance with NEC800 CEC Section 60 Grounding and polarization This unit may be equipped with a polarized alternating current line plug a plug with one blade wider than the other blade This safety feature allows the plug to fit into the power outlet in only one way If unable to insert the plug fully into the outlet contact a locally certified electrician to replace the obsolete outlet Do not defeat the safety purpose of the polarized plug Alternately this unit may be equipped with a 3 pole grounding plug a plug with a third pin for earth grounding This safety feature allows the plug to fit into a grounded power outlet only If unable to insert the plug into the outlet contact a locally certified electrician to replace the obsolete outlet Do not defeat the safety purpose of the grounding p
28. Supply Box with a transformer comes with a barrier that separates the high voltage side on the left from the low voltage 24 VAC side on the right 3 Cut and trim all wires with sufficient slack to reach their connector terminals in the box but not so long as to be pinched by or to obstruct closing the Pendant Arm Refer to the image above for the connector locations 4 Attach the supplied 3 pin Power Plug to the incoming power wires Refer to connector P101 for wire connections 5 If audio input and or audio output is required attach the supplied 6 pin SERIAL COMMUNICATIONS to P106 in the Power Supply Box Refer to connector P106 in the Power Supply Box Connections section below 6 Attach an RJ45 plug to the incoming Ethernet cable Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 26 en Installing the Pendant Arm Wall Corner and Mast Pole Mounts Connecting Alarm Inputs and Outputs gt wires Alarm Out 4 is a relay AUTODOME 7000 To connect alarm inputs and outputs attach the supplied 6 pin Alarms In and the 4 pin Alarms Out connector plugs with flying lead wires to the appropriate incoming alarm PIN 1 2 3 4 PIN 1 2 3 ORANGE 4 5 6 NOOO AONB Figure 8 1 Alarm and relay connectors 1 4 pin Alarm 2 6 pin Alarm In 3 7 pin Relay Connector P104 Connector P102 Connector P103 Pin
29. TCP rate control Select On to control the rate of transmission control protocol Select Off if you do not want to control the TCP rate HTTP browser port Select a different HTTP browser port from the list if required The default HTTP port is 80 If you want to allow only secure connections via HTTPS you must deactivate the HTTP port In this case select Off HTTPS browser port If you wish to allow browser access on the network via a secure connection select an HTTPS browser port from the list if necessary The default HTTPS port is 443 Select the Off option to deactivate HTTPS ports only unsecured connections will now be possible The camera uses the TLS 1 0 encryption protocol You may have to activate this protocol via your browser configuration You must also activate the protocol for the Java applications via the Java control panel in the Windows control panel Notice If you want to allow only secure connections with SSL encryption you must select the Off option for each of the parameters HTTP browser port RCP port 1756 and Telnet support This deactivates all unsecured connections Connections will then only be possible via the HTTPS port You can activate and configure encryption of the media data video and metadata on the Encryption page see Encryption page 128 RCP port 1756 To exchange connection data you can activate the unsecured RCP port 1756 If you want connection data to be transmitted only when enc
30. Type 4X environment the connected equipment must have a Type 4X environmental rating In order to maintain the integrity of a Type 4 environment the connected equipment must have a Type 4 Type 4X Type 6 or Type 6P environmental rating Route Wires and Attach Connectors Power wires must be routed to the left front side of the Power Supply Box through a separate electrically earth grounded conduit All video control and alarm wires must be routed through a second electrically earth grounded conduit to the right side of the box Warning External interconnecting cables are to be installed in accordance to NEC ANSI NFPA70 for US application and Canadian Electrical Code Part CSA C22 1 for CAN application and in accordance to local country codes for all other countries Branch circuit protection incorporating a 20 A 2 pole Listed Circuit Breaker or Branch Rated Fuses are required as part of the building installation A readily accessible 2 pole disconnect device with a contact separation of at least 3 mm 0 12 in must be incorporated There are two possible methods to route the video control and alarm wires Method One is to route the video control and alarm wires through the conduit fitting on the right front side of the Power Supply Box and out to the AUTODOME Interface Board Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 42 en Installing the Roof Parapet and Pipe Mounts
31. Video black 8 Serial Communications green Not applicable for AUTODOME Used for Audio Input Output in 7000 Series cameras AUTODOME 7000 Series Notice Refer to the Connection page 71 chapter for wire specifications and distances 1 Route all incoming wires through one of the earth grounded conduits at the bottom of the Mounting Plate For a mast mount route all wires through the right angle conduit 2 Attach the water tight plug to the other conduit 3 Attach the grounding spade terminal item 1 below to one of the spade terminals inside the Mounting Plate 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Installing the Pendant Arm Wall Corner and Mast Pole Mounts en 37 Figure 8 11 Mounting Plate Inside Detail Ref Description 1 Grounding lug with two spade terminals 2 Earth ground lug with crimp ring terminal 3 Wire input conduit holes 4 Connect the incoming 24 VAC power wires to the 5 pin 24 VAC Power In mating connector supplied with the Mounting Plate kit for the camera and for the Heater 10 11 12 13 Attach the grounding spade from the 5 pin mating connector to the other spade terminal inside the mounting plate Attach the 5 pin Power In mating connector to the 24 VAC Power cable cable 2 connected to the pendant Remove the mating connector from the Relay Contacts cable cable 3
32. a tree or a flag swaying in the wind in a confined area after the specified number of seconds Settings range from 5 to 120 The default is 30 Auto pan left limit Sets the left Auto Pan limit of the camera Use the preview window to move the camera to the left pan limit and click the button The camera will not move past this limit when in Auto Pan Between Limits mode AUX 2 ON 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 14 18 Configuration via IP Advanced Mode en 105 Auto pan right limit Sets the right Auto Pan limit of the camera Use the preview window to move the camera to the right pan limit and click the button The camera will not move past this limit when in Auto Pan Between Limits mode AUX 2 ON Tilt up limit Sets the upper tilt limit of the camera Use the preview window to move the camera to the tilt limit and click the button Tilt limits Click the Reset button to clear the upper tilt limit Tour A Tour B Starts and stops the recording of a recorded guard tour The camera can make up to two 2 recorded tours A recorded tour saves all manual camera movements made during the recording including its rate of pan tilt and zoom speeds and other lens setting changes The tour does not capture camera video during the recording of the tour Note 1 You can save a total of 15 minutes of recorded actions between the two tours To record a tour 1 Cli
33. able to withstand this pull out force For example 19 mm 3 4 inch minimum for plywood For a Corner installation Secure the Corner Plate to the wall corner using four 4 studs not included Secure the Mounting Plate to the Corner Plate using the four 4 3 8 x 1 3 4 inch bolts and split lock washers supplied For a Mast or pole installation The metal straps included with the Mast mount accommodate a pole with a diameter of 100 380 mm 4 15 in You must use a banding tool sold separately for a mast or pole installation In addition you must obtain a 3 4 in 20 mm right angle conduit connector through which you route the wires that connect to the pendent arm Follow the instructions provided with the banding tool to securely mount the Mast Plate to the pole Contact your Bosch Sales Representative to order Banding Tool P N TC9311PM3T Secure the Mounting Plate to the Mast Plate using the four 4 3 8 x 1 3 4 inch bolts and split lock washers supplied Remove one of the rubber gaskets from the Mounting Plate Once the Mounting Plate item 1 below is attached to the Mast Plate item 2 connect the right angle conduit item 3 to the Mounting Plate through the empty conduit hole as shown below 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Installing the Pendant Arm Wall Corner and Mast Pole Mounts en 35 3 Ensure that the mounting plate is secure Attach th
34. all remote stations to which a connection is to be possible Notice If you enter the destination IP address 0 0 0 0 for destination 10 this address will no longer be used for the tenth attempt at automatic connection in the event of an alarm The parameter is then used only to save the general password Video transmission If the unit is operated behind a firewall TCP HTTP port should be selected as the transfer protocol For use in a local network select UDP Caution Please note that in some circumstances a larger bandwidth must be available on the network for additional video images in the event of an alarm in case Multicast operation is not possible To enable Multicast operation select the UDP option for the Video transmission parameter here and on the Network page see Network Access page 122 Stream Select the number of the stream from the drop down list Remote port Depending on the network configuration select a browser port here The ports for HTTPS connections will be available only if the On option is selected in the SSL encryption parameter Video output If you know which unit is being used as the receiver you can select the analog video output to which the signal should be switched If the destination unit is unknown it is advisable to select the First available option In this case the image is placed on the first free video output This is an output on which there is no signal The connected m
35. and the connection You can save these messages automatically in a file see the online help System Log Ssu US Z2UUS UD service 30 03 2009 09 T Aarm Input Ss jz Alarm input 4 4 Video loss alarm 7 Events such as the triggering or end of alarms are shown in the Event Log field You can save these messages automatically in a file see the online help 1 Ifyou want to delete the entries click the delete icon in the top right hand corner of the relevant field 2 Ifyou want to view a detailed log click the icon in the top right hand corner of the relevant field A new window will open Audio function All users who are connected to the camera via Web browser can receive audio signals from the camera Audio signals can only be sent to the camera by the user who connects to the unit first 1 On the LIVE page click anywhere next to the video image to remove the focus from the ActiveX 2 Hold down the F12 key to establish a voice connection to the camera The browser s status bar displays the message Send Audio ON 3 Release the F12 key when you want to stop sending audio signals to the camera The status bar displays the message Send Audio OFF Notice When the voice contact connection to the camera is broken the next user to make a connection to the camera can send audio data to the camera Aux Control Tab The AUX Control tab is used to enter pre programmed keyboard control commands These
36. be particularly advantageous for networks with low bandwidths The image rate in images per second ips appears next to the text field or slider Video resolution Select the desired resolution for the video image For standard definition only options are 240p 480p 144p 288p 432p default Expert Settings If necessary use the expert settings to adapt the l frame quality and the P frame quality to specific requirements The setting is based on the H 264 quantization parameter QP GOP structure Select the structure that you require for the group of pictures depending on whether you place greater priority on having the lowest possible delay IP frames only or using as little bandwidth as possible Options are IP IBP and IBBP GOP is not available for megapixel cameras Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 98 en Configuration via IP Advanced Mode AUTODOME 7000 I frame distance This parameter allows you to set the intervals in which the I frames will be coded Auto means auto mode whereby the video server inserts I frames as necessary Values range from 3 to 60 An entry of 3 indicates that I frames are continuously generated An entry of 4 indicates that only every fourth image is an I frame and so on the frames in between are coded as P frames Note that the values supported depend on the GOP structure setting For example only even values are supported
37. commands are composed of a command number plus the appropriate function key Show scene Set scene AUX on AUX off A valid combination either issues a command to the camera or displays an on screen menu To access the AUX Control tab go to the LIVE page and click the AUX Control tab 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Operation en 135 vi a 7 9 3 3 3 cic 1 Command number field 2 Keypad numbers 0 9 3 Show a preset scene 4 Set a preset scene 5 Initiates a command 6 Deletes a number in the Command Number field 7 Used to select a menu item 8 Stops a command Notice Some commands such as Set 110 Set 899 that were SET commands in previous AUTODOME models are no longer SET commands See the Appendix for the complete list of commands and how to activate them To Enter a Keyboard Control Command 1 2 3 4 Place the cursor in the Command Number field Click the desired command number via the on screen keypad Click either the Aux on button or the Aux off button to initiate or stop the command If the command initiates a menu use the Up Down arrows on the View Control to navigate the menu Click the Focus button or Iris button to select a menu item To Set a Preset Shot Preset shots or scenes are camera positions that are saved in memory for future use f 2 3 Move
38. connected to a grounded outlet or its ground terminal is properly connected to a ground source 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Safety EN en 9 Disconnect the unit s input connectors from outdoor equipment before disconnecting the grounding plug or grounding terminal Follow proper safety precautions such as grounding for any outdoor device connected to this unit U S A models only Section 810 of the National Electrical Code ANSI NFPA No 70 provides information regarding proper grounding of the mount and supporting structure grounding of the coax to a discharge unit size of grounding conductors location of discharge unit connection to grounding electrodes and requirements for the grounding electrode Notice This device is intended for use in public areas only U S federal law strictly prohibits surreptitious recording of oral communications aaa Your Bosch product was developed and manufactured with high quality material and components that can be recycled and reused This symbol means that electronic and electrical appliances which have reached the end of their working life must be collected and disposed of separately from household waste material Separate collecting systems are usually in place for disused electronic and electrical products Please dispose of these units at an environmentally compatible recycling facility per European
39. en 125 Mail address Enter the email address for notification Advanced The settings on this page are used to implement advanced settings for the network User Mode Select the appropriate mode for cloud based services Off O Auto default option RTSP port If necessary select a different port for the exchange of the RTSP data from the list The standard RTSP port is 554 Select Off to deactivate the RTSP function Authentication If a RADIUS server is employed in the network for managing access rights authentication must be activated here to allow communication with the unit The RADIUS server must also contain the corresponding data To configure the unit you must connect the camera directly to a computer using a network cable This is because communication via the network is not enabled until the Identity and Password parameters have been set and successfully authenticated Identity Enter the name that the RADIUS server is to use for identifying the camera Password Enter the password that is stored in the RADIUS server NTCIP Specifies a set of rules and protocols for organizing describing and exchanging transportation management information between transportation management applications and transportation equipment such that they interoperate with each other Select a port for NTCIP and the Address from the appropriate drop down lists TCP port The device can receive data from an external TCP sender for
40. example an ATM or POS device and store it as metadata Select the port for TCP communication Select Off to deactivate the TCP metadata function Sender IP address Enter the IP address of the TCP metadata sender here Network Management SNMP The camera supports the SNMP V1 Simple Network Management Protocol for managing and monitoring network components and can send SNMP messages traps to IP addresses The unit supports SNMP MIB II in the unified code If you wish to send SNMP traps enter the IP addresses of one or two required target devices here If you select On for the SNMP parameter and do not enter an SNMP host address the camera does not send them automatically but only replies to SNMP requests If you enter one or two SNMP host addresses SNMP traps are sent automatically Select Off to deactivate the SNMP function 1 SNMP host address 2 SNMP host address If you wish to send SNMP traps automatically enter the IP addresses of one or two required target units here Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 126 en Configuration via IP Advanced Mode AUTODOME 7000 SNMP traps You can select which traps are to be sent 1 Click Select A list is opened 2 Click the checkboxes to select the required traps All the checked traps will be sent 3 Click Set to accept the selection UPnP You can activate the Universal Plug and Play UPnP function If the function is turned
41. feature is not available on 20x models High dynamic range Select On to activate wide dynamic range which improves image reproduction in extreme high contract scenes Select Off to deactivate the feature Select Enhanced to activate high dynamic range when the camera detects an extreme high contract scene The camera makes multiple simultaneous exposures of the same scene to capture details in both bright and dark parts of the scene Night mode Selects night mode B W to enhance lighting in low light scenes Select from the following options Monochrome Forces the camera to stay in Nigh Mode and transmit monochrome images Color The camera does not switch to Night Mode regardless of ambient light conditions 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 14 16 Configuration via IP Advanced Mode en 103 Auto default The camera switches out of Night Mode after the ambient light level reaches a pre defined threshold Night mode threshold Adjusts the level of light at which the camera automatically switches out of night mode B W operation Select a value between 10 and 55 in increments of 5 where 10 is earlier and 55 is later Noise Reduction Turns on the 2D and 3D noise reduction feature Noise Reduction Level Adjusts the noise level to the appropriate level for shooting conditions Select a value between 1 and 5 Anti fog Select Auto to configure t
42. individual images snapshots should be displayed below the live image Individual images can only be saved if this icon is visible Allow local recording Here you can specify whether the icon for saving recording video sequences on the local memory should be displayed below the live image Video sequences can only be saved if this icon is visible I frames only stream Here you can specify whether the LIVE page displays a viewing tab for an I frame only stream Show scene list Here you can specify whether the View Controls section of the LIVE page displays a drop down box with the list of scenes set in Advanced Mode gt Camera gt Scenes and Tours of the SETTINGS page Show Intelligent Tracking Here you can specify whether the LIVE page displays the controls for the Intelligent Tracking feature Show Special Functions Here you can specify whether the LIVE page displays the Special Functions section Path for JPEG and video files 1 Enter the path for the storage location of individual images and video sequences that you can save from the LIVE page Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 94 en Configuration via IP Advanced Mode AUTODOME 7000 14 9 14 10 14 11 2 If necessary click Browse to find a suitable directory Logging Save event log Check this option to save event messages in a text file on your local computer You can then view edit and print th
43. options for controlling peripherals are displayed with the mouse cursor 3 To manually pan throughout the image area move your cursor over any part of the live video The image area displays a directional arrow R AK Y then click and hold the right mouse key to pan the camera Preset List The View Control Tab displays a list of all presets with their titles if any are defined below Presets 1 6 To move the camera to a preset scene select the appropriate preset from the drop down list Refer to Scenes and Tours page 105 to define a preset scene and to specify a title for the preset View Control Aux Control Set 110 Scene 110 Figure 16 1 View control tab preset scene list Digital 1 0 The alarm icon is for information purposes and indicates the status of an alarm input When an alarm is triggered the icon lights up blue The device s configuration determines whether the alarm is displayed as well as additional details see the AUTODOME 7000 Series online help Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 134 en Operation AUTODOME 7000 Triggering Relay You can switch connected units using the relays in the camera for example lights or door openers gt To activate this click the icon for the relay next to the video image The icon will be red when the relay is activated System Log The System Log field contains information about the operating status of the camera
44. password a second time to eliminate typing mistakes Notice A new password is only saved when you click the Set button You should therefore click the Set button immediately after entering and confirming a password 14 4 Date Time Date format Select your required date format Device date Device time Notice Ensure that recording is stopped before synching to the PC If there are multiple devices operating in your system or network it is important to synchronize their internal clocks For example it is only possible to identify and correctly evaluate simultaneous recordings when all units are operating on the same time 1 Enter the current date Since the unit time is controlled by the internal clock there is no need to enter the day of the week it is added automatically 2 Enter the current time or click the Sync to PC button to copy your computer s system time to the camera Note It is important that the date time is correct for recording An incorrect date time setting could prevent correct recording Device time zone Select the time zone in which your system is located Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 90 en Configuration via IP Advanced Mode AUTODOME 7000 Daylight saving time The internal clock can switch automatically between normal and daylight saving time DST The unit already contains the data for DST switch overs up to the year 2018
45. target Use the pendant arm mount if possible This mount option provides the most stability for the camera Use guy wires to protect against strong winds if using the parapet mount Field of View Select a location and viewing angle that allows the flow of people to move across the camera s field of view Avoid motion that moves directly towards the camera Avoid locations that attract large numbers of people such as retail stores or intersections Intelligent Tracking is optimized for scenes with very few moving objects Unwanted Motion Avoid neon lights flashing lights night time lights and reflected light from a window or mirror for example The flickering of these lights can affect the Intelligent Tracking operation Avoid motion from moving leaves branches that present a persistent fixed motion Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 140 en Operation AUTODOME 7000 Operation of Intelligent Tracking The Intelligent Tracking feature behaves in one of the following ways Camera detects an object in motion and automatically tracks the object User actions always take precedence over Intelligent Tracking If the camera is actively tracking an object and a user takes control the camera will attempt to track the object after a period of inactivity An IVA alarm can trigger Intelligent Tracking to track a detected object A rule that triggers an IVA e
46. that the PC and the camera are on the same Subnet 2 Launch your web browser such as Microsoft Internet Explorer and navigate to the following URL http 192 168 0 1 The web browser opens the LIVE page for the device a security warning message is displayed 3 Check the Always Trust Box and then click YES Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 82 en Configuration 4 Click the Settings link located at the top of the LIVE page AUTODOME 7000 5 Inthe left pane of the window click Advanced Mode and then click Network The Network menu expands 6 Click Network Access to open the Network Access page Network Access Figure 13 1 Network Access page 160 10 132 71 160 10 39 10 fd00 7 5f7a e652 1 160 10 39 10 255 255 0 0 160 10 39 10 5 g 3 K K 5 K 7 Configure the settings on this page based on the addresses provided by your local network administrator Note that the text on the Set button changes to Set and Reboot 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Configuration en 83 8 Click Set and Reboot The camera will reset go through the homing sequence which usually takes 30 seconds to complete and then the LIVE page appears with updated video and the new IP address Notice Click the Help on this page link if you need more information About the SETTINGS Page
47. the wall location on the roof for the camera and use the Parapet wall mount bracket as a template to mark the hole locations Notice Allow enough room below the Parapet Mount Bracket to route the video control and alarm wires up through the Parapet arm In certain installations you may have to lift the Parapet arm for the camera to clear the top of the wall when it is swung into position Provide enough slack in the wires to rotate the pipe arm over the roof and back when camera maintenance is required 2 Prepare the mounting surface for the type of fastener by drilling holes for the mounting anchors as required Figure 9 7 Parapet Wall Mount Bracket and Roof Mount Plate 1 Pipearm 4 Apply sealant around each fastener hole 2 Parapet Wall Bracket 5 Roof Mount Plate 3 3 8 16 SS Hex Head Bolt 6 Usea minimum of six 6 fasteners not supplied supplied Eight 8 fastener holes shown 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Installing the Roof Parapet and Pipe Mounts en 49 Notice Fasteners are not supplied with the Roof Parapet Mount Kit since it depends on the material to which it is attached The material must accommodate a minimum pull out strength of 275 kg 600 Ibs For example 19 mm 3 4 inch minimum for plywood Fasteners can include bolts studs or lag bolts All fasteners must be made of corrosion resistant stainless steel wi
48. to 31 The default value is 0 Line Out You can set the line output gain using the slider Values range from O to 79 The default value is 0 13 6 Basic Mode Recording You can record the images from the camera on various local storage media or on an appropriately configured iSCSI system Storage medium 1 Select the required storage medium from the list 2 Click the Start button to start the recording immediately 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Configuration via IP Basic Mode en 87 13 7 Basic Mode System Overview The data on this page are for information purposes only and cannot be changed Keep a record of this information in case technical assistance is required Notice You can select all required text on this page with the mouse and copy it to the clipboard with the Ctrl C key combination for example if you want to send it via e mail Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 88 en Configuration via IP Advanced Mode AUTODOME 7000 14 Configuration via IP Advanced Mode 14 1 Advanced Mode General v Advanced Mode v General Identification Password Date Time Display Stamping 14 2 Identification Camera name The camera name makes it easier to identify the remote camera location in the event of an alarm for example It will be displayed in the video screen if configured to do so
49. where the data stream is simultaneously distributed to multiple receivers in a defined group Multicast You can enter a dedicated multicast address and port for each stream You can switch between the streams by clicking the appropriate tabs Notice Multicast operation requires a multicast enabled network that uses the UDP and the Internet Group Management IGMP protocols Other group management protocols are not supported The TCP protocol does not support multicast connections A special IP address class D address must be configured for multicast operation in a multicast enabled network The network must support group IP addresses and the Internet Group Management Protocol IGMP V2 The address range is from 225 0 0 0 to 239 255 255 255 The multicast address can be the same for multiple streams However it will be necessary to use a different port in each case so that multiple data streams are not sent simultaneously using the same port and multicast address Notice The settings must be made individually for each stream 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Configuration via IP Advanced Mode en 127 Enable To enable simultaneous data reception on several receivers you need to activate the multicast function To do this check the box You can then enter the multicast address Multicast Address Enter a valid multicast address for each stream to be operat
50. with IBP if you have selected IBBP only 3 or multiples of 3 are supported Min P frame QP This parameter allows you to adjust the image quality of the P frame and to define the lower limit for the quantization of the P frames and thus the maximum achievable quality of the P frames In the H 264 protocol the Quantization Parameter QP specifies the degree of compression and thus the image quality for every frame The lower the quantization of the P frame QP value the higher the encoding quality and thus the best image quality and the lower the frame refresh rate depending on the settings for the maximum data rate under network settings A higher quantization value results in low image quality and lower network load Typical QP values are between 18 and 30 The basic setting Auto automatically adjusts the quality to the settings for the P frame video quality 1 P frame delta QP This parameter sets the ratio of the I frame quantization QP to the P frame quantization QP For example you can set a lower value for I frames by moving the slide control to a negative value Thus the quality of the I frames relative to the P frames is improved The total data load will increase but only by the portion of I frames The basic setting Auto automatically adjusts to the optimum combination of movement and image definition focus To obtain the highest quality at the lowest bandwidth even in the case of increased movement in the pi
51. 0 F 01U 283 679 68 en Preparing the Bubble AUTODOME 7000 10 Preparing the Bubble The inside of the housing may contain packing material to safeguard the camera during shipping If so you must remove the packing material before attaching the in ceiling housing to the interface box Notice To avoid excessive moisture saturation inside the housing limit the amount of time that the bubble is disconnected from the housing Bosch recommends that the bubble be removed from the housing for no more than five 5 minutes Remove the bubble from an in ceiling housing 1 Loosen the lockscrew item 1 in the illustration below in the trim ring using a P1 or smaller Phillips screwdriver until the bubble can rotate freely 2 Then rotate the bubble counterclockwise approximately 1 4 turn until it releases from the In Ceiling Housing See the figure below for an illustration Figure 11 1 Bubble Release Screw 3 Remove the foam inserts surrounding the camera module Remove the bubble from a pendant housing 1 Using both hands apply a firm counterclockwise looking up at the dome rotational force on the Pendant Bubble Assembly to set the bubble latch 2 Insert a small 2 mm straight blade screw driver into the release opening in the bubble trim ring to release the lock and then remove the screwdriver 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Preparing the Bubble en 6
52. 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 14 51 14 52 Configuration via IP Advanced Mode en 129 Advanced Mode Service Maintenance page 129 Licenses page 130 Diagnostics page 130 System Overview page 130 Maintenance Upgrading your camera The camera allows an operator to update the camera firmware via the TCP IP network The Maintenance page allows updates of the firmware For the latest firmware go to www boschsecurity com navigate to the product page for your camera and then download the software from the Software tab The preferred method to update your camera is through a direct connection between the camera and a PC This method entails connecting the Ethernet cable from the camera directly to the Ethernet port of a PC If the direct connect method is not practical you can also update the camera through a Local Area Network LAN You cannot however update the camera through a Wide Area Network WAN or via the Internet Update server Enter the path of the server on which to perform the update Click Check to verify the path Firmware The camera is designed in such a way that its functions and parameters can be updated with firmware To do this transfer the current firmware package to the unit via the selected network It will then be automatically installed there In this way a camera can be serviced and updated remotely without a technician having to change the installatio
53. 14 54 Diagnostics Accesses the Built in Self Test BIST The BIST displays a Pass or Fail status on the most recent homing event not a counter For the other items a counter is maintained Click the Start BIST button to display the number of times the camera performed a homing event failed to home properly restarted lost video 14 55 System Overview The data on this page are for information purposes only and cannot be changed Keep a record of this information in case technical assistance is required Notice You can select all required text on this page with the mouse and copy it to the clipboard with the Ctrl C key combination for example if you want to send it via e mail 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 15 15 1 Operation en 131 Operation Using the AUTODOME Camera The AUTODOME 7000 transmits PTZ control commands and images over a TCP IP network It also allows users to configure the camera display settings camera operating settings and to configure the network parameters The camera incorporates a network video server in the IP module The primary function of the server is to encode video and control data for transmission over a TCP IP network With its H 264 encoding it is ideally suited for IP communication and for remote access to digital video recorders and multiplexers The use of existing networks means that integ
54. 3 Power Supply Box and cover with 120 VAC transformer VG4 A PSU1 or with 230 VAC transformer VG4 A PSU2 The following table lists the optional parts sold separately that you may need for attaching a Pendant to the Roof Parapet and Pipe mount packages Mounting Options Part Numbers Optional Flat Roof Mount Adapter for VGA ROOF MOUNT Tools Required LTC 9230 01 Wall Mount Corner Mount Quantity Item For Mount Type Supplied by Bosch 1 Allen wrench 5 mm Pendant Arm to Yes Mast pole Mount Roof parapet Mount Pipe Mount 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Unpacking en 15 Screwdriver straight Pendant Arm to No blade 2 5 mm 0 1 in Wall Mount Corner Mount Mast pole Mount Roof parapet Mount Pipe Mount In ceiling Mount Screwdriver straight Pendant Arm to No blade 3 1 mm 1 8 in Wall Mount Corner Mount Mast pole Mount Roof parapet Mount Pipe Mount In ceiling Mount Screwdriver No 2 Pendant Arm to No Phillips Wall Mount Corner Mount Mast pole Mount Roof parapet Mount Pipe Mount In ceiling Mount Socket wrench Pendant Arm to No Wall Mount Corner Mount Mast pole Mount Roof parapet Mount Pipe Mount Socket 9 16 in Pendant Arm to No
55. 7 operating system network access and reception software such as the Bosch Video Management System or the Video Client or A compatible hardware decoder from Bosch Security Systems as a receiver and a connected video monitor Notice The Web browser must be configured to enable Cookies to be set from the IP address of the unit In Windows 7 deactivate protected mode on the Security tab under Internet Options You can find notes on using Microsoft Internet Explorer in the online Help in Internet Explorer In Windows Vista deactivate protected mode on the Security tab under Internet Options You can find notes on using Microsoft Internet Explorer in the online Help in Internet Explorer If you choose to use a computer running Microsoft Internet Explorer or any of the Bosch software the computer must conform to the following minimum requirements Operating System Windows XP Service Pack 3 or Windows 7 32 or 64 bits Processor Intel Pentium Quad Core 3 0 GHz or comparable RAM 2048 MB Free Hard Disk Space 10 GB Video system NVIDIA GeForce 8600 or higher display with a minimum of 16 bit color Network interface 100 1000 BaseT Software Microsoft Internet Explorer version 8 0 or higher Video Client DirectX 9 0c Oracle Java Virtual Machine 1 6 0 26 or newer The camera includes the means to decode the video via a web browser however for more advanced features such as local recordi
56. 83 679 46 en Installing the Roof Parapet and Pipe Mounts AUTODOME 7000 Figure 9 4 Power Supply Box Connections 1 Ground Screw 5 Power In 2 Transformer 115 230 VAC Modes 6 In Out 1 2 in 15 mm NPS Fitting 3 In Out to camera 7 Power In 3 4 in 20 mm NPS Fitting 4 24 VAC to Dome Interface Board 8 Control Data and Video In Out 3 4 in 20 mm NPS Fitting Warning Fuse replacement by qualified service personnel only Replace with same type fuse Fuse Specifications Volts XF101 Mains XF102 Camera XF103 Heater 24 V T5 0A T2 0A T3 15A 115V T16A T2 0A T3 15A 230V T0 8A T2 0A T3 15A The following table lists the Power Supply Box connectors 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Installing the Roof Parapet and Pipe Mounts en 47 No Connector Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Ground Grounding Screw P101 115 230 VAC or Line NC Neutral 24 VAC Power In P107 24 VAC Power to Dome Dome Earth Ground Heater Heater Dome Plug 24 VAC 24 VAC 24 VAC 24 VAC Table 9 1 Power Box Connections 8 3 Attach Cover Door to Power Supply Box Figure 9 5 Align Cover Door Hinge to Power Box Compress the bottom hinge pin by pushing the pin lever down and then rotate it behind the Hinge Pi
57. 9 Figure 11 2 Pendant Bubble Release Opening 3 Firmly rotate the bubble counterclockwise approximately 20 degrees until the bubble assembly releases from the Pendant Housing Replace the trim ring optional In ceiling models The dome bubble for in ceiling models of AUTODOME 7000 comes assembled with a white trim ring An optional black trim ring is supplied in the shipping box To replace the white trim ring follow these steps 1 Remove the four 4 Phillips head screws from the inner ring 2 Remove the white trim ring 3 For In ceiling models verify that the trim ring gasket is in place Refer to the graphic in Installing the Ceiling IP54 Housing Gasket page 64 for an illustration of the correct placement of the gasket 4 Place the black trim ring over the inner ring 5 Replace and tighten the four 4 screws Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 70 en Preparing the Bubble AUTODOME 7000 Replace the bubble in an in ceiling housing Figure 11 3 In Ceiling Bubble 1 Use a non permanent marking instrument such as chalk or a carpenter pencil to mark on the ceiling the screw slot in the in ceiling housing 2 Place the bubble over the Camera Module and align it until it settles 3 Rotate the trim ring not the bubble itself clockwise until it locks in position in the housing The ring becomes tight and may be difficult to turn Aligning the screw slots by usi
58. AUTODOME 7000 VG5 7130 VG5 7230 BOSCH en Operation Manual AUTODOME 7000 Table of contents Table of Contents en 3 1 Safety EN 6 1 1 About this Manual 6 1 2 Legal Information 6 1 3 Safety Precautions 6 1 4 Important Safety Instructions 6 1 5 Important Notices 8 1 6 Connection in Applications 11 1 7 Customer Support and Service 11 2 Unpacking 13 2 1 Parts List Installation 13 2 2 Tools Required 14 2 3 Additional Products Required 16 3 System overview 17 4 Pre installation Checklist 19 4 1 Stabilization 20 5 Installing the Optional SD Card 21 6 Mount Power Supply Box Wall Mast Pole and Corner Mounts 23 7 Installing the Pendant Arm Wall Corner and Mast Pole Mounts 25 7 1 Description 25 7 2 Route Wires and Attach Connectors 25 7 3 Route Power through Intermediate Power Supply Box 29 7 4 Attach Pendant Arm to Power Supply Box 32 7 5 Make Connections in the Power Supply Box 33 7 6 Installing the VGA PEND WPLATE 34 7 7 Attach Pendant to Arm and Tighten 38 8 Installing the Roof Parapet and Pipe Mounts 41 8 1 Description 41 8 2 Route Wires and Attach Connectors 41 8 3 Attach Cover Door to Power Supply Box 47 8 4 Installing the VGA ROOF MOUNT 48 8 5 Installing the VG4 A 9543 Pipe Mount 50 8 6 Wire the Pipe Interface Board 52 8 7 Attach Pendant to Pipe and Tighten 56 8 8 Make Connections in the Power Supply Box 58 9 Installing the In Ceiling Mount 59 9 1 Description 59 9 2 Dimensi
59. E 7000 System overview en 17 3 System overview The AUTODOME 7000 Series camera includes the following functionality Function Video Encoding Description The camera uses the H 264 compression standards and ensures that the data rate remains low even with high image quality and can also be adapted to local conditions within wide limits Streaming Multicast Encodes multiple data streams simultaneously according to individually customized profiles This feature creates data streams that can serve different purposes For example one 1 data stream for recording and one 1 data stream optimized for transmission over the Local Area Network LAN Enables simultaneous real time transmission to multiple receivers The network must implement the UDP and IGMP V2 protocols as a prerequisite for Multicasting Configuration Allows configuration for all camera settings from a Web browser on the local network Intranet or on the Internet You can also update the firmware load device configurations store configuration settings and copy these settings from one camera to another Intelligent Tracking Snapshots Continuously follows an individual Intelligent Tracking operates by recognizing an individual in motion and zooms in to approximately 50 of the field of view for an average target height of six feet Allows you to take and store individual video frames as JPEG images from the Web browser interface
60. Insert the Pipe Interface Board into the down pipe and fasten the three 3 retaining screws to secure the board to the Dome Cap Caution Be careful not to strip the threads when tightening the Pipe Interface Board retaining screws Figure 9 13 Pipe Interface Board to Dome Cap Assembly 1 Interface Board 2 Retaining Screws 3 3 Pendant Mounting Screws 2 8 7 Attach Pendant to Pipe and Tighten 1 Before attaching the Pendant visually inspect the Pendant dome and the Interface Board connectors for any blocked pin holes and bent pins 2 Tilt the Pendant enough to place its mounting hook on top of the its housing over the recessed hinge pin of the Dome Cap 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Installing the Roof Parapet and Pipe Mounts en 57 Figure 9 14 Pendant to Roof Pipe Mount Attachment 1 Tilt Dome 2 Hook and drop 2a Dome Cap 2b Recessed Hinge Pin 2c Dome Connector 3 Rotate down to engage dome connector 4 Tighten the two 2 mounting screws to a minimum torque of 10 12 N m 90 105 in lbs 3 Drop the Pendant down slightly to engage the dome hook and hinge pin of the Dome Cap allowing the dome to rotate around the hinge pin 4 Rotate the dome housing down to a vertical position and gently push upward to engage the connector on top of the dome housing Caution If you fe
61. Interface Box to the housing Figure 10 10 In Ceiling Housing and Interface Box 1 Interface Box 4 Thumb Screw 2 Ball Stud 5 Tether Point 3 In ceiling Housing 6 Ceiling Clamp 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Installing the In Ceiling Mount en 67 Caution The In ceiling dome is provided with tether points on each side of the housing To prevent injury attach a safety wire from a secure anchor point above the ceiling to a tether point on the dome housing See below for an illustration 9 9 Secure Housing to Ceiling The In ceiling Housing is secured to the ceiling by two 2 screw clamps 1 Insert the In ceiling Mount Assembly through the hole in the ceiling 2 Tighten both clamps using a 2 Phillips screwdriver to secure the housing to the ceiling Da A T 0 26 in MINIMUM CEILING 40 mm 1 57 in MAXIMUM CEILING od mm inches gt s Figure 10 11 Secure camera to ceiling 1 Tether Point 4 Ceiling Clamp 2 Ceiling Clamp 5 Rotate Clockwise to Engage Clamp 3 Tether Point Caution Over torquing the Ceiling Clamps can damage the clamp or ceiling Only tighten the clamp until it contacts the ceiling and you start to feel some resistance If using a power screwdriver set the torque level to the lowest setting Bosch Security Systems Inc Operation Manual 2014 04 2
62. MUNICATIONS 6 In Out 1 2 in 15 mm NPS Fitting Warning In earlier Bosch AUTODOME cameras cable 8 in the ARM mount is labeled Control In Out and was used for external RxD TxD and Biphase communications In the AUTODOME 7000 Series cameras If you are mounting an AUTODOME 7000 Series camera to an ARM mount that was wired for an earlier model of Bosch AUTODOME you must either re wire cable 8 to be audio input and output or disconnected it from the power supply Cables wires that are routed through number 2 in the illustration above come from the Nexus cable bundle that is in the pendant Arm Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 28 en Installing the Pendant Arm Wall Corner and Mast Pole Mounts AUTODOME 7000 Fuse Specifications Volts XF101 Mains XF102 Camera XF103 Heater 24V T5 0A T2 0A T3 15A 115V T1 6A T2 0A T3 15A 230 V T 0 8A T2 0A T3 15A Warning Fuse replacement by qualified service personnel only Replace with same type fuse Fuse Specifications Volts XF101 Mains XF102 Camera XF103 Heater 24V T5 0A T2 0A T3 15A 115 V T1 6A T2 0A T3 15A 230 V T 0 8A T2 0A T3 15A The following table lists the Power Supply Box connectors No Connector Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Ground Grounding Screw P101 115 230 VAC or Line NC Neutral 24 VAC Pow
63. Pendant to the Arm Wall Corner or Mast mount packages Mounting Options Part Numbers Pendant Arm Only VGA PEND ARM Pendant Arm with Mounting Plate VGA PEND WPLATE 24 V VG5 models only no power supply box Pendant Arm with one of the following Power Supply Boxes Power Box without transformer 24 VAC VG4 A PAO Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 14 2 2 en Unpacking Mounting Options AUTODOME 7000 Part Numbers Power Box with 120 VAC transformer VG4 A PA1 or with 230 VAC transformer VG4 A PA2 Power Supply Box and cover with 120 VAC transformer VG4 A PSU1 or with 230 VAC transformer VG4 A PSU2 Trim Skirt for Power Supply Box optional VG4 A TSKIRT Bosch High PoE 60W midspan NPD 6001A Corner Mount Kit Corner Mount Plate VG4 A 9542 Mast Pole Mount Kit Mast Mount Plate VG4 A 9541 Fiber Optic Ethernet Media Converter Kit VG4 SFPSCKT The following table lists the mandatory parts sold separately that you will need for attaching a Pendant to the Roof Parapet and Pipe mount packages Mounting Options Part Numbers Parapet Roof Mount with one of the following Power Supply Boxes VGA ROOF MOUNT Power Supply Box and cover with 120 VAC transformer VG4 A PSU1 or with 230 VAC transformer VG4 A PSU2 Pipe Mount with one of the following Power Supply Boxes VG4 A 954
64. SU2 Power Supply Box The main power supply connected to the P101 connector and to the grounding screw The 24 VAC power out wire connected to the P107 heater power connectors VG4 PSU1 VG4 PSU2 Figure 8 3 VG4 PSU1 VG4 PSU2 1 120 230 VAC Power In 5 Transformer 2 Ground Wire 6 In Out Conduit 1 2 in 15 mm NPS Fitting 3 P101 Connector 7 24 VAC Power Out to VG4 PAO 4 P107 Connector Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 30 en Installing the Pendant Arm Wall Corner and Mast Pole Mounts AUTODOME 7000 To properly wire the incoming high voltage and the outgoing low voltage lines refer to this table No Connector Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Ground Grounding Screw P101 120 230 VAC Power In Line NC Neutral P107 24 VAC Power Out Earth Ground Heater Heater 24 VAC 24 VAC Table 8 2 VG4 PSU1 VG4 PSU2 Power Supply Box Connections 1 Route the high voltage 120 230 VAC lines through the earth grounded conduit fitting on the left side of the box The Power Supply Box with a transformer comes with a barrier that separates the high voltage side on the left from the low voltage 24 VAC side on the right Cut and trim the high voltage 120 230 VAC power and ground wires with sufficient slack to reach their connector terminal in the box but not so long as to be pinched by or to obstruct clos
65. The SETTINGS page provides access to the configuration menu which contains all the unit s parameters arranged in groups You can view the current settings by opening one of the configuration screens You can change the settings by entering new values or by selecting a predefined value from a list field There are two options for configuring the unit or checking the current settings Basic mode Advanced mode In Basic Mode the most important parameters are arranged in seven groups This allows you to change the basic settings with just a few entries and then put the device into operation Advanced Mode is recommended for expert users or system support personnel You can access all unit parameters in this mode Settings that affect the fundamental functionality of the unit such as firmware updates can only be altered in the advanced mode Caution The settings in the Advanced Mode should only be processed or modified by expert users or system support personnel All settings are backed up in camera memory so they are not lost even if the power fails The exception is the time settings which are lost after 1 hour without power if no central time server is selected Starting Configuration gt Click the SETTINGS link in the upper section of the window The Web browser opens a new page with the configuration menu Navigation 1 Click one of the menu items in the left window margin The corresponding submenu is displayed 2
66. Wall Mount Corner Mount Mast pole Mount Roof parapet Mount Pipe Mount Banding tool Mast pole mount Yes but sold Bosch P N separately TC9311PM83T from mount Right angle NPS conduit Mast pole mount with No connector 3 4 in 20 VGA PEND WPLATE mm Screwdriver medium Roof parapet Mount No straight blade Pipe Mount Screwdriver No 1 Roof parapet Mount No Phillips Pipe Mount Pipe wrench Roof parapet Mount No Pipe Mount Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 16 en Unpacking AUTODOME 7000 1 Barrel connector Roof parapet Mount No Pipe Mount Only if installing a fiber optic model 1 Appropriate tool for In ceiling Mount No cutting a hole in drywall or ceiling tile 1 Pliers In ceiling Mount No 2 3 Additional Products Required The following table lists additional products sold separately by Bosch or other manufacturers necessary to install AUTODOME cameras Quantity Product Part Number Size 1 SD card user supplied Water tight metal conduit user supplied 20 mm 0 75 in UL listed liquid tight strain reliefs user supplied Weatherproof sealant user supplied 4 Studs stainless steel corrosion user supplied 6 4 mm 0 25 in resistant to 8 mm 5 16 in 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOM
67. You can use these data or create alternative time saving data if required Notice If you do not create a table there will be no automatic switching When changing and clearing individual entries remember that two entries are usually related to each other and dependent on one another switching to summer time and back to normal time 14 5 1 First check whether the correct time zone is selected If it is not correct select the appropriate time zone for the system and click the Set button 2 Click the Details button A new window will open and you will see the empty table 3 Select the region or the city that is closest to the system s location from the list field below the table 4 Click the Generate button to generate data from the database in the unit and enter it into the table 5 Make changes by clicking an entry in the table The entry is selected 6 Clicking the Delete button will remove the entry from the table 7 Select other values from the list fields below the table to change the entry Changes are made immediately 8 If there are empty lines at the bottom of the table for example after deletions you can add new data by marking the row and selecting required values from the list fields 9 Now click the OK button to save and activate the table Time server IP address The camera can receive the time signal from a time server using various time server protocols and then use it to set the internal clock Th
68. ages caused by improper installation are not covered by warranty as they do not affect the functionality of the camera 6 Outdoor installation Use proper surge suppression on your network video power audio and alarm cables 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Operation en 143 7 SD card This information is provided to assist the customer in the selection of an appropriate SD device as a means for recording video It is not an endorsement of a specific technology or supplier AUTODOME 7000 Series cameras can record video and audio to user supplied local memory cards SD SDHC or SDXC hereafter referred to as SD cards Bosch has identified best practices with respect to the selection and use of SD cards in the products 1 Select an SD card with a read write speed of at least 1OMB second and class 6 2 Ensure that write protection is off Check the slider if applicable 3 Switch off power to the unit before inserting the SD card 4 Stop recording and switch off power to the unit before removing the SD card Bosch recommends that you frequently check the recording status of your equipment Periodic replacement of the SD card may be required It is recommended that redundant recording systems are considered and that information is always backed up As with all storage media the lifetime of an SD card varies by supplier and use conditions The lifetime of a SD ca
69. ake the desired changes 2 Click the Set and Reboot button The camera reboots and the changed settings are activated Caution If you change the IP address subnet mask or gateway address the camera is only available under the new addresses after the reboot Automatic IP assignment If a DHCP server is employed in the network for the dynamic assignment of IP addresses you can activate acceptance of IP addresses automatically assigned to the camera Certain applications Bosch Video Management System Archive Player Configuration Manager use the IP address for the unique assignment of the unit If you use these applications the DHCP server must support the fixed assignment between IP address and MAC address and must be appropriately set up so that once an IP address is assigned it is retained each time the system is rebooted IPv4 Fill in the 3 fields in this section of the screen IP address Enter the desired IP address for the camera in this field The IP address must be valid for the network Subnet mask Enter the appropriate subnet mask for the selected IP address here Gateway address If you want the unit to establish a connection to a remote location in a different subnet enter the IP address of the gateway here Otherwise leave the box blank 0 0 0 0 IPv6 Consult with the network administrator before making changes to this section IP address Enter the desired IP address for the camera in this field The IP a
70. alarm to be triggered This setting is independent of the sensor fields selected under Select Area Set a high value if fewer sensor fields need to change to trigger an alarm With a low value it is necessary for changes to occur simultaneously in a large number of sensor fields to trigger an alarm This option allows you to detect independently of motion alarms manipulation of the orientation or location of a camera resulting from turning the camera mount bracket for instance Global change Activate this function if the global change as set with the Global change slide control should trigger an alarm Scene too bright Activate this function if tampering associated with exposure to extreme light for instance shining a flashlight directly on the lens should trigger an alarm The average brightness of the scene provides a basis for recognition Scene too dark Activate this function if tampering associated with covering the lens for instance by spraying paint on it should trigger an alarm The average brightness of the scene provides a basis for recognition Scene too noisy Activate this function if tampering associated with EMC interference noisy scene as the result of a strong interference signal in the vicinity of the video lines as an example should trigger an alarm Reference Check You can save a reference image that is continuously compared with the current video image If the current video image in the mark
71. an tilt and zoom speeds and other lens setting changes To program a recorded tour refer to PTZ Settings To stop a tour click a directional control in the View Control tab Warning Save presets using One Push Spot Focus Refer to Lens Settings page 103 Find home Click the Find home button to recalibrate the home position for the camera Show home Click the Show home button to display the current home position Refocus Click the Refocus button to issue the One Push focus command One Push activates the Auto Focus feature after the camera stops moving Saving Snapshots You can save individual images from the video sequence currently shown on the LIVE page in JPEG format on your computer s hard drive The icon for recording single images is only visible if the unit is configured to enable this process gt Click the icon The storage location depends on the configuration of the camera 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Operation en 137 Recording Video Sequences You can save sections of the video sequence currently shown on the LIVE page on your computer s hard drive The icon for recording video sequences is only visible if the unit is configured to enable this process gt Click the icon to start recording The storage location depends on the configuration of the camera A red dot in the icon indicates that recording is in progress 1 Click the ico
72. anual Bosch Security Systems Inc AUTODOME 7000 14 23 14 24 14 25 Configuration via IP Advanced Mode en 107 If you connect via Web browser you must activate the audio transmission on the LIVE Functions page See L VE Functions page 93 For other connections the transmission depends on the audio settings of the respective system Audio The audio signals are sent in a separate data stream parallel to the video data and so increase the network load The audio data are encoded according to G 711 and require an additional bandwidth of approximately 80 kbps for each connection If you do not want any audio data to be transmitted select Off Input volume You can set the input volume with the slider from O to 31 with O as the default Line In You can set the line input gain with the slider from O zero to 79 with O as the default Make sure that the display does not go beyond the green zone during modulation Line Out You can set the line output gain with the slider from O zero to 79 with O as the default Make sure that the display does not go beyond the green zone during modulation Recording format Select a format for audio recording Select L16 or AAC Advanced Audio Coding if you want better audio quality with higher sampling rates Note that the L16 standard requires approximately eight times the bandwidth of the format G 711 Pixel Counter Counts the number of pixels in a defined image area The pixe
73. below For a Mast or a pole installation The metal straps included with the Mast mount accommodate a pole with a diameter of 100 380 mm 4 15 in You must use a banding tool sold separately for a mast or pole installation Follow the instructions provided with the banding tool to securely mount the Mast Plate to the pole Contact your Bosch Sales Representative to order Banding Tool P N TC9311PM3T 5 Secure the Power Supply Box to the Corner Plate or Mast Plate using the four 4 3 8 x 1 3 4 inch bolts and split lock washers supplied 6 Attach 3 4 inch 20 mm NPS watertight earth grounded conduit pipe fittings not supplied to the bottom or back holes of the Power Supply Box through which you will run the power video and control data wires Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 24 en Mount Power Supply Box Wall Mast Pole and Corner Mounts AUTODOME 7000 Warning For units intended to be installed outdoors All wiring power and I O cabling connecting to the unit must be routed separately inside different permanently earthed metal conduits not supplied 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 7 1 7 2 Installing the Pendant Arm Wall Corner and Mast Pole Mounts en 25 Installing the Pendant Arm Wall Corner and Mast Pole Mounts Description This chapter details how to install an AUTODOME to a Wall C
74. button An alarm e mail is immediately created and sent 14 36 Alarm Task Editor Caution Editing scripts on this page overwrites all settings and entries on the other alarm pages This procedure cannot be reversed In order to edit this page you must have programming knowledge and be familiar with the information in the Alarm Task Script Language document As an alternative to the alarm settings on the various alarm pages you can enter your desired alarm functions in script form here This will overwrite all settings and entries on the other alarm pages 1 Click the Examples link under the Alarm Task Editor field to see some script examples A new window will open 2 Enter new scripts in the Alarm Task Editor field or change existing scripts in line with your requirements 3 When you are finished click the Set button to transmit the scripts to the unit If the transfer was successful the message Script successfully parsed is displayed over the text field If it was not successful an error message will be displayed with further information 14 37 Alarm Rules The camera features an alarm rule engine In its simplest form an alarm rule can define which input s activate which output s Basically an alarm rule allows you to customize the camera to respond automatically to different alarm inputs To configure an alarm rule specify one input from a physical connection a motion detection trigger or from a connection to the
75. camera s LIVE page The physical input connection can be activated by dry contact devices such as pressure pads door contacts and similar devices 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 14 38 14 39 14 40 Configuration via IP Advanced Mode en 121 Next specify up to two 2 rule outputs or the camera s response to the input Outputs include a physical alarm relay an AUX command or a preposition scene 1 Click the Enabled check box to activate the alarm 2 Choose one of the following alarm Inputs Local Input 1 a physical alarm connection Local Input 2 a physical alarm connection IVA MOTION an alarm when IVA or motion detection is activated Connection an alarm when an attempt is made to access the camera s IP address 3 Choose one of the following output commands for both Output 1 and Output 2 settings None no defined command Alarm Relay defines a physical connection from the open collector alarm output Aux On defines a standard or custom keyboard ON command Refer to User Command Table page 149 for a list of valid commands Note Only commands 1 8 18 20 43 60 80 86 are supported Support for the remaining commands is scheduled for a future release Aux Off defines a standard or custom keyboard OFF command Refer to to User Command Table page 149 for a list of valid commands Note Only commands 1 8 18 20 43 60 80 86 are supported Suppor
76. can also enable additional information overlays for the LIVE page see LIVE Functions page 93 Motion detector MOTION only For the detector to function the following conditions must be met Analysis must be activated Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 116 en Configuration via IP Advanced Mode AUTODOME 7000 At least one sensor field must be activated The individual parameters must be configured to suit the operating environment and the desired responses The sensitivity must be set to a value greater than zero Caution Reflections of light off glass surfaces etc switching lights on or off or changes in the light level caused by cloud movement on a sunny day can trigger unintended responses from the motion detector and generate false alarms Run a series of tests at different times of the day and night to ensure that the video sensor is operating as intended For indoor surveillance ensure constant lighting of the areas during the day and at night Sensitivity MOTION only The basic sensitivity of the motion detector can be adjusted for the environmental conditions to which the camera is subject The sensor reacts to variations in the brightness of the video image The darker the observation area the higher the value that must be selected Minimum object size MOTION only You can specify the number of sensor fields that a moving object must c
77. ck the Start Recording button The system prompts you to overwrite the existing tour 2 Click Yes to overwrite the existing tour movements 3 Click the View Control link under the image cameo to access the directional and zoom controls 4 Use the View Control dialog box to make the necessary camera movements 5 Click the Stop Recording button to save all actions North point Click the Set button to overwrite the existing North point Click the Defaults button to reset the North point to factory defaults Scenes and Tours The camera can store up to 256 preset scenes You can define the individual scenes that comprise a preposition tour You define individual preposition scenes then use these scenes to define the preposition tour The tour starts from the lowest scene number in the tour and progresses sequentially to the highest scene number in the tour The tour displays each scene for a specified dwell time before advancing to the next scene By default all scenes are part of the preposition tour unless removed To define and edit an individual scene 1 Click the View Control link Use the PTZ controls to move the camera into position Navigate to the scene that you want to define as a preposition Click the Add scene button to define the preposition Select a number for the scene from 1 to 256 Type an optional name for the scene up to 20 characters long Click OK to save the scene to the Preposition list The asterisk
78. class 4 standard required Terminal Connector RJ45 Female 11 4 Notice Consult the National Electrical Code NEC for cable bundling requirements and limitations Fiber Optic Ethernet Media Converter Optional The fiber optic media converter is designed to transmit 10 100 Mbps Ethernet signals over fiber optic cable using 10 100 Mbps Small Form factor Pluggable SFP modules The SFP modules are available as multi mode fiber MMF or single mode fiber SMF models with a single SC connector or dual fiber with an LC connector Refer to the VG4 SFPSCKT Fiber Optic Media Converter Installation Guide Ethernet Media Converter Data Interface Ethernet Data Rate 10 100 Mbps IEEE 802 3 Compliant Full Duplex or Half Duplex Electrical Port Full Duplex Optical Port Fiber Type MMF 50 125 um MMF For 50 125 um fiber subtract 4 dB from the specified optical budget value Must meet or exceed fiber standard ITU T G 651 Fiber Type SMF 8 10 125 um SMF Must meet or exceed fiber standard ITU T G 652 Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 74 en Connection Ethernet Media Converter AUTODOME 7000 Maximum Distance 20 km 12 4 miles Requirement Media converter receiver CNFE2MC IN at controller end of system Terminal Connection Duplex LC or Single SC 11 5 Alarms and Relay Connections Alar
79. connectors P103 and P102 in the Interface Box 1 To connect supervised alarms and relays attach the appropriate wires to their terminals on the P104 connector on the Pipe Interface Board Refer to the Connection page 71 chapter for more details on wiring alarms 2 Attach the lid to the Interface box Align the slots on the lid with the two posts at the rear of the Interface box Rotate the lid down Squeeze the ground clips located at the front of the box against the Interface box with your fingers before closing the lid to ensure that the lid does not catch on the ground clips Secure the lid to the Interface box by pushing the lid down until the clip on the lid catches against the box 9 6 Interface Box Connections The following figure is a detailed illustration of the In ceiling Interface box 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Figure 10 7 In ceiling Interface Box Installing the In Ceiling Mount en 63 1 Fiber Optics 5 Coax Video Not applicable for AUTODOME 7000 Series cameras 2 Ethernet Video 6 Alarm In 3 Dome Power 7 Analog In 4 Data In Out 8 Relay
80. ct a specific profile you must also select MOTION in the Analysis Type field VCA Profiles You can configure two profiles with different VCA configurations You can save profiles on your computer s hard drive and load saved profiles from there This can be useful if you want to test a number of different configurations Save a functioning configuration and test new settings You can use the saved configuration to restore the original settings at any time 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Configuration via IP Advanced Mode en 115 Notice If computing power becomes short the highest priority is always the live images and recordings This can lead to impairment of the video content analysis You should therefore observe the processor load and optimize the encoder settings or the video content analysis settings as necessary 1 Select a VCA profile and enter the required settings If necessary click the Default button to return all settings to their default values 3 Click the Save button to save the profile settings to another file A new window is opened in which you can specify where you want to save the file and what name you want to save it under 4 Click the Load button to load a saved profile A new window opens in which you can select the profile file and specify where to save the file VCA configuration Select one of the profiles here to activate it or
81. cture configure the quality settings as follows 1 Observe the coverage area during normal movement in the preview images 2 Set the value for Min P frame QP to the highest value at which the image quality still meets your needs 3 Set the value for I P frame delta QP to the lowest possible value This is how to save bandwidth and memory in normal scenes The image quality is retained even in the case of increased movement since the bandwidth is then filled up to the value that is entered under Maximum bit rate Default Click Default to return the profile to the factory default values 14 13 Encoder Streams Property Select one of the H 264 standards for each stream Stream 1 recording Options are H 264 MP SD H 264 MP 720p25 30 Fixed H 264 MP 1080p25 30 Fixed H 264 MP 720p50 60 Fixed Note In order to select the option H 264 MP 720p50 60 Fixed here you must set the Max frame rate field in the Advanced Mode Camera gt Installer Menu to H 264 MP 720p50 60 Fixed first 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Configuration via IP Advanced Mode en 99 Note for dynamic models only In order to select the option H 264 MP 1080p25 30 Fixed here you must set the Max frame rate field in the Advanced Mode Camera gt Installer Menu to H 264 MP 1080p25 30 Fixed first Stream 2 Options vary depending on Stream 1 selectio
82. d Corner Mounts en 23 Mount Power Supply Box Wall Mast Pole and Corner Mounts Before mounting the Power Supply Box decide if you should wire the box through the holes in the bottom or back of the box If wiring the box through the back move the two 2 seal plugs to the bottom through the holes before mounting Notice Use 3 4 inch 20 mm NPS fittings for the holes on the bottom and back of the box Use 1 2 inch 15 mm NPS fittings for the side holes SAX Figure 7 1 Power Supply Wall Mast Pole and Corner Mounts 1 Use the wall mount template supplied in the packaging box to locate the four 4 mounting holes for the Power Supply Box 2 Drill four 4 holes for the mounting anchors If installing outdoors apply a weatherproof sealant around each hole at the mounting surface Warning A stud diameter of 6 4 mm 1 4 inch to 8 mm 5 16 inch able to withstand a 120 kg 265 Ib pull out force is recommended The mounting material must be able to withstand this pull out force For example 19 mm 3 4 inch minimum for plywood 3 Place the Power Supply Box into the optional Trim Skirt 4 Secure the Power Supply Box to the mounting surface For a Wall installation Use four 4 corrosion resistant stainless steel studs not supplied Then proceed to Step 5 below For a Corner installation Secure the Corner Plate to the wall corner using four 4 studs not included Then proceed to Step 5
83. ddress must be valid for the network A typical IPv6 address may resemble the following example 2001 db8 52 1 1 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Configuration via IP Advanced Mode en 123 Consult the network administrator for valid IPv6 address construction Prefix length A typical IPv6 node address consists of a prefix and an interface identifier total 128 bits The prefix is the part of the address where the bits have fixed values or are the bits that define a subnet Gateway address If you want the unit to establish a connection to a remote location in a different subnet enter the IP address of the gateway here Otherwise leave the box blank 0 0 0 0 DNS server address 1 DNS server address 2 The camera is easier to access if the unit is listed on a DNS server If you wish for example to establish an Internet connection to the camera it is sufficient to enter the name given to the unit on the DNS server as a URL in the browser Enter the IP address of the DNS server here Servers are supported for secure and dynamic DNS Video transmission If the unit is operated behind a firewall TCP HTTP port should be selected as the transfer protocol For use in a local network select UDP Caution Multicast operation is only possible with the UDP protocol The TCP protocol does not support multicast connections The MTU value in UDP mode is 1 514 bytes
84. dia You can delete all recordings on a storage medium at any time 14 26 Caution Check the recordings before deleting and back up important sequences on the computer s hard drive 1 Click a storage medium in the Managed storage media list to select it 2 Click the Edit button below the list A new window will open 3 Click the Formatting button to delete all recordings in the storage medium 4 Click OK to close the window Deactivating Storage Media You can deactivate any storage medium from the Managed storage media list It is then no longer used for recordings 1 Click a storage medium in the Managed storage media list to select it 2 Click the Remove button below the list The storage medium is deactivated and removed from the list Recording Profiles You can define up to ten different recording profiles You will then use these recording profiles in the recording scheduler where they are linked with the individual days and times see Recording Scheduler page 111 Notice You can change or add to the recording profile description on the tabs on the Recording Scheduler page see Recording Scheduler page 111 1 Click one of the tabs to edit the corresponding profile If necessary click the Default button to return all settings to their default values 3 Click the Copy Settings button if you want to copy the currently visible settings to other profiles A new window will open and you can select the pr
85. dopts the selection at the top of the page Alarm input Analysis alarm Video loss alarm Here you can select the alarm sensor that is to trigger a recording Virtual alarm Here you can select the virtual alarm sensors that are to trigger a recording via RCP commands or alarm scripts for example Notice For more information please see the Alarm Task Script Language document and the RCP documentation These documents can be found on the product CD supplied Recording includes You can specify whether in addition to video data and metadata for example alarms VCA data and serial data should also be recorded Including metadata could make subsequent searches of recordings easier but it requires additional memory capacity Caution Without metadata it is not possible to include video content analysis in recordings 14 27 Maximum Retention Time You can specify the retention times for recordings If the available memory capacity of a medium has been used older recordings are only overwritten if the retention time entered here has expired Notice Make sure that the retention time corresponds with the available memory capacity A rule of thumb for the memory requirement is as follows 1 GB per hour retention time with 4CIF for complete frame rate and high image quality Maximum Retention Time Enter the required retention time in hours or days for each recording Recording 1 corresponds to Stream 1 Recording 2 c
86. e Pendant Arm to the Mounting Plate The bottom hinge pin of the Pendant Arm is provided with a Hinge Pin Stop to hold the hinge open while attaching the arm to the Mounting Plate 1 Compress the bottom hinge pin by pushing the pin lever downward and rotating it behind the Hinge Pin Stop Figure 8 9 Connect Pendant Arm to Mounting Plate 2 Open the top hinge by pushing its pin lever up and holding it Note Both Hinge Pins must be fully compressed to open unlock the hinges of the Pendant Arm and before proceeding to the next step 3 While continuing to hold the top hinge pin open align the top and bottom hinges of the Pendant Arm to their mating points on the Mounting Plate Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 36 en Installing the Pendant Arm Wall Corner and Mast Pole Mounts AUTODOME 7000 4 Once you have the hinges aligned release the top hinge pin to engage its mating hinge on the Mounting Plate Then release the bottom hinge pin from the Hinge Pin Stop to lock the Pendant Arm to the Mounting Plate Route and Connect Wires to a Power Supply Box The illustration below depicts the power and control cables connected to the Pendant Arm Figure 8 10 Pendant Arm Cables Cable Cable 1 Grounding Strap black 5 UTP Video Ethernet blue 2 24 VAC Power red 6 Alarm Outputs white 3 Relay Contacts yellow 7 Alarm Inputs gray 4 Coax
87. e directly into the sun or fluorescent lighting If so reposition camera The image on the screen is distorted Is the power frequency set properly in sync If the power frequency is not set correctly the line lock synchronization mode cannot be used Set the synchronization mode to INT NTSC Model power frequency in LL mode 60 Hz No video Check that the mains power to the power supply is on Check to see if you have a web page If you do not then you may have the wrong IP address Use Configuration Manager to identify the correct IP address If O K then Check that there is 24 V output from the transformer If O K then Check the integrity of all wires and mating connectors to the camera No camera control Ensure that the LAN cable has good connection and is secured Refresh the browser and ensure that video is updated For analog cameras Cycle the camera s power off and on For IP cameras Ping the camera s IP address and try again to control the camera Camera moves when moving other cameras Check that the camera s IP address is properly set If camera s IP address is not set then Use Configuration Manager to confirm that two cameras do not have the same IP address If they do change the address of one of the cameras 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Troubleshooting en 145
88. e product Warning Only in ceiling models of the AUTODOME can be connected to a PoE switch Outdoor models should be used only with the Bosch High PoE 60W Midspan 4 Installation in an area with high humidity Ideally the bubble of your dome camera should remain in place The dome contains a desiccant pack to control the level of moisture inside the camera Removing the bubble from the dome exposes the desiccant to moisture that could negatively affect the performance of the camera If you must remove the bubble for example to install or remove an SD card do not leave the bubble off of the dome for longer than five minutes Bosch also recommends that you keep the dome camera in its packaging until you are ready to install the camera 5 Installation in a corrosive environment for example near a coastline The fasteners and fixtures shipped with the camera help to keep the camera secure Always use Bosch supplied screws and other fasteners when installing or performing maintenance on the camera Before installation inspect the metal parts of the camera for paint that is chipped or otherwise damaged If you notice any paint damage touch up the damage with locally available paint or sealants Avoid installation practices that may bring the camera s metal mountings in contact with materials such as stainless steel Such contacts can result in galvanic corrosion and degrade the cosmetic appearance of the camera These cosmetic dam
89. e scene 11 To display IVA behind privacy masks click the IVA behind masks check box Notice Draw the mask 10 larger than the object to ensure that the mask completely covers the object as the camera zooms in and out Click the Zoom threshold box Draw the mask at 50 optical zoom or less for improved masking performance Notice The camera disables the Privacy Mask feature if the orientation of the camera is set to Inverted Refer to nstaller Menu page 94 for orientation settings See also Installer Menu page 94 14 15 Picture Settings Current mode Select one of the pre programmed user modes optimized with the best settings for a variety of typical applications that best defines the environment in which the camera is installed Outdoor General day to night changes with sun highlights and street lighting Indoor Ideal mode for indoor applications where lighting is constant and not changing Low light Optimized for sufficient details at low light Motion Monitoring traffic or fast moving objects motion artifacts are minimized Vibrant Enhanced contrast color reproduction and sharpness The default setting depends on whether the camera is an in ceiling camera or a pendant camera 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Configuration via IP Advanced Mode en 101 Customize the mode if necessary for the specific requirements of the site by se
90. e the recording parameters iSCSI Media If you want to use an iSCSI system as a recording medium you must set up a connection to the required iSCSI system and set the configuration parameters Notice The iSCSI storage system selected must be available on the network and completely set up Amongst other things it must have an IP address and be divided into logical drives LUN 1 Enter the IP address of the required iSCSI destination in the iSCSI IP address field Ifthe iSCSI destination is password protected enter this into the Password field 3 Click the Read button The connection to the IP address will be established In the Storage overview field you can see the corresponding logical drives Local Media The supported local recording media are displayed in the Storage overview field Activating and Configuring Storage Media The storage overview displays the available storage media You can select individual media or iSCSI drives and transfer these to the Managed storage media list You can activate the storage media in this list and configure them for storage Caution Each storage medium can only be associated with one user If a storage medium is already being used by another user you can decouple the user and connect the drive with the camera Before decoupling make absolutely sure that the previous user no longer needs the storage medium 1 Inthe Recording media section click the iSCSI Media and Local Media tab
91. e unit polls the time signal automatically once every minute Enter the IP address of a time server here Time server type Select the protocol that is supported by the selected time server Preferably you should select the SNTP server as the protocol This supports a high level of accuracy and is required for special applications and subsequent function extensions Select Time server for a time server that works with the protocol RFC 868 Display Stamping Various overlays or stamps in the video image provide important supplementary information These overlays can be enabled individually and are arranged on the image in a clear manner After you set all necessary parameters click the View Control link to see how the stamping appears on the LIVE page Camera name stamping This field sets the position of the camera name overlay It can be displayed at the Top at the Bottom or at a position of your choice that you can then specify using the Custom option Or it can be set to Off for no overlay information 1 Select the desired option from the list 2 Ifyou select the Custom option additional fields are displayed where you can specify the exact position Position XY 3 Inthe Position XY fields enter the values for the desired position 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Configuration via IP Advanced Mode en 91 Time stamping This field sets the p
92. eads to thoroughly fill all voids 7 Thread the Pipe Cap onto the down pipe and tighten securely to prevent leaks Warning You must thread the Dome Cap onto the pipe until it is tight Failure to do so can result in damage or serious injury or death Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 52 en Installing the Roof Parapet and Pipe Mounts AUTODOME 7000 8 6 Wire the Pipe Interface Board This section provides instructions for connecting wires and cables to the Pipe Interface Board as illustrated below Refer to the Connection page 71 chapter for cable and wiring recommendations and specifications 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Installing the Roof Parapet and Pipe Mounts en DOOOOO eA hed Pea ete at he 2 2 2 2 2 0O e N ea l ay e l Figure 9 11 Pipe Interface Board Connections 1 Pipe Interface Module 2 Video Coax In J102 Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 54 en Installing the Roof Parapet and Pipe Mounts AUTODOME 7000 3 6 pin Connector P103 Alarms In 3 7 4 4 pin Connector P102 Alarms Out 1 3 5 100 Q Resistor P105 Note When using the audio input in an AUTODOME 7000 Series camera remove this resistor 6 Data In Out P105 AWG i Biphase C 26 16 For AUTODOME
93. ectors see option B below 2 4 Figure 12 1 AUTODOME 7000 Series System Configuration 1 AUTODOME 7000 Series 2 IP Connection 3 Network Switch 4 Computer Notice You can also use the Bosch Video Client software application to configure the network settings for an AUTODOME 7000 Series camera Go to www boschsecurity com to download the Configuration Manager software and Operating Manual 11 2 Power Cable and Wire Distances Guides Power 115 230 VAC Copper Wire To comply with local codes Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 72 en Connection AUTODOME 7000 Caution Compliance with EN50130 4 Alarm Standard CCTV for Security Applications To meet the requirements of the EN50130 4 Alarm Standard an ancillary uninterruptable power UPS supply is necessary The UPS must have a Transfer Time between 2 6 ms anda Backup Runtime of greater than 5 seconds for the power level as specified on the product datasheet Maximum Wire Distances from Power Supply to AUTODOME 24 V to AUTODOME VA Watts 14 AWG 16 AWG 18 AWG 2 5 mm 1 5 mm 1 0 mm HD models with IVA Outdoor 60 55 58 m 190 ft 36 m 119 ft 23 m 75 ft Maximum Wire Distances from Power Supply to AUTODOME 7000 HD 24 V to AUTODOME 7000
94. ed areas differs from the reference image an alarm is triggered This allows you to detect tampering that would otherwise not be detected for example if the camera is turned 1 Click Reference to save the currently visible video image as a reference 2 Click Select Area and select the areas in the reference image that are to be monitored 3 Check the box Reference check to activate on going matching The stored reference image is displayed in black and white below the current video image and the selected areas are marked in yellow Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 118 en Configuration via IP Advanced Mode AUTODOME 7000 4 Select the Disappearing edges or Appearing edges option to specify the reference check once again Disappearing edges The area selected in the reference image should contain a prominent structure If this structure is concealed or moved the reference check triggers an alarm If the selected area is too homogenous so that concealing and moving the structure would not trigger an alarm then an alarm is triggered immediately to indicate the inadequate reference image Appearing edges Select this option if the selected area of the reference image includes a largely homogenous surface If structures appear in this area then an alarm is triggered Select Area You can select the image areas in the reference image that are to be monitored The video image is subd
95. ed in multicast mode duplication of the data streams in the network With the setting 0 0 0 0 the encoder for the relevant stream operates in multi unicast mode copying of data streams in the unit The camera supports multi unicast connections for up to five simultaneously connected receivers Notice Duplication of data places a heavy demand on the unit and can lead to impairment of the image quality under certain circumstances 14 47 Port Assign a different port to each data stream if there are simultaneous data streams at the same multicast address Enter the port address of the required stream here Streaming Click the checkbox to activate multicast streaming mode for the relevant stream An enabled stream is indicated by a check mark Multicast packet TTL You can enter a value to specify how long the multicast data packets are active on the network This value must be greater than one if multicast is to be run via a router Image Posting You can save individual JPEG images on an FTP server at specific intervals You can then retrieve these images at a later date to reconstruct alarm events if required In order to configure image posting and to save and retrieve JPEG images you must create an Account in which to save and access them If you have not configured an account the following error message appears at the top of this page No configured account Configure accounts Click the link to access the Accounts
96. edit it You can rename the profile 1 To rename the file click the icon to the right of the list field and enter the new profile name in the field 2 Click the icon again The new profile name is saved Preset Select Off or Test Alarm status The alarm status is displayed here for information purposes This means you can check the effects of your settings immediately Aggregation times Use the slider from O zero to 20 0 is the default to select the aggregation times Analysis type Select the required analysis algorithm By default only MOTIONS is available this offers a motion detector and essential recognition of tampering Notice Additional analysis algorithms with comprehensive functions such as IVMD and IVA are available from Bosch Security Systems Inc If you select one of these algorithms you can set the corresponding parameters here directly You can find information on this in the relevant documents on the product CD supplied Metadata is always created for a video content analysis unless this was explicitly excluded Depending on the analysis type selected and the relevant configuration additional information overlays the video image in the preview window next to the parameter settings Options are MOTIONG IVA 5 6 IVA 5 6 Flow With the MOTION analysis type for example the sensor fields in which motion is recorded will be marked with rectangles Notice On the LIVE Functions page you
97. el any resistance when rotating the dome housing or when engaging the connector stop immediately and start over 5 Hold the housing firmly in position and alternately tighten the two 2 5 mm Allen head mounting screws from above to a torque value of 10 12 N m 90 105 in Ibs Caution You must tighten the two mounting screws to a minimum torque of 10 12 N m 90 105 in lbs to ensure a proper seal between the arm and the housing 6 Rotate the arm to swing the camera out from the roof and into position if installing a Parapet Roof Mount 7 Tighten the three 3 10 mm 3 8 inch stainless steel hex bolts on the bracket to lock the Parapet Arm in position Caution Do not over tighten the bolts The maximum torque is 34 N m 25 ft lb Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 58 en Installing the Roof Parapet and Pipe Mounts AUTODOME 7000 8 8 Make Connections in the Power Supply Box 1 Attach the earth ground wire to the grounding screw on the left side of the box Connect the 24 VAC to Dome plug installed previously to its mating connector P107 on the right side of the box 3 Connect the 115 230 VAC 3 pin Power in plug installed previously to its mating connector P101 on the left side of the box 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 9 2 9 3 9 4 Installing the In Ceiling Mount en 59 In
98. emove the bubble from a pendant housing page 68 2 Press down the end of the SD card until it ejects partially from the connector Pull out the SD card and put it in a safe location 4 Follow the steps in one of these sections depending on the type of camera mount Replace the bubble in an in ceiling housing page 70 or Replace the bubble in a pendant housing page 70 G Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 148 en Technical data AUTODOME 7000 18 Technical data For product specifications see the datasheets for AUTODOME IP 7000 Series and for AUTODOME HD 7000 Series available on the appropriate product pages of the Online Product Catalog at www boschsecurity com 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 19 User Command Table User Command Table en 149 Notice Some of the following commands may not apply to your camera Locked Alarm Rule Function Comm Command Description Output Key No Y On Off 1 Scan 360 Auto Pan without limits Y On Off 2 Auto Pan Auto Pan between limits Y On Off 8 Play Pre position Tour Activate Deactivate V Y On Off 18 AutoPivot Enable Enables disables AutoPivot Y On Off 20 Backlight Comp Backlight Compensation Y On Off 24 Stabilization Electronic Stabilization Available only with the AUTODOME 7000 IP Y On Off 40 Res
99. er In P106 SERIAL CODE CODE Earth GND RXD TXD Signal COMMUNICATIONS Audio IN Audio IN Ground Audio OUT Audio OUT GND Audio in Audio Audio out Ground signal signal ground ground P107 24 VAC Power Camera Camera Earth Heater Heater Arm Harness 24 VAC 24 VAC Ground 24 VAC 24 VAC Table 8 1 Power Supply Box Connections Notice Pins for P106 1 2 4 and 5 are used for audio input and output for AUJTODOME 7000 Series cameras however their labels are still those of previous versions of analog AUTODOME cameras 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Warning Installing the Pendant Arm Wall Corner and Mast Pole Mounts en 29 For units intended to be installed outdoors All wiring power and I O cabling connecting to the unit must be routed separately inside different permanently earthed metal conduits not supplied 7 3 Route Power through Intermediate Power Supply Box You may route the main power supply through a VG4 PSU1 120 V transformer or through a VG4 PSU2 230 V transformer Power Supply Box before connecting the power to a VG4 PAO 24 V no transformer Power Supply Box The main issue with this configuration is that the 5 pin power out connector from the VG4 PSU1 or VG4 PSU2 does not match to the 3 pin power input of the VG4 PAO power supply The illustration below depicts AVG4 PSU1 VG4 P
100. eries of tests at different times of the day and night to ensure that the video sensor is operating as intended Notice The options for tamper detection can only be set for fixed cameras Dome cameras or other motorized cameras cannot be protected in this manner as the movement of the camera itself causes changes in the video image that are too great 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Configuration via IP Advanced Mode en 117 Sensitivity Notice This and the following parameter are only accessible if the reference check is activated The basic sensitivity of the tamper detection can be adjusted for the environmental conditions to which the camera is subject The algorithm reacts to the differences between the reference image and the current video image The darker the observation area the higher the value that must be selected Trigger delay s You can set delayed alarm triggering The alarm is only triggered after a set time interval in seconds has elapsed and then only if the triggering condition still exists If the original condition has been restored before this time interval elapses the alarm is not triggered This allows you to avoid false alarms triggered by short term changes for example cleaning activities in the direct field of vision of the camera Global change You can set how large the global change in the video image must be for an
101. erminal Audio Line Level Output Connections 1 Connect the audio line level input of the audio output device for example an amplified speaker or a PC line level input to the Audio _Out RXD output terminal 2 Connect the audio line level output signal ground to the Audio _Out TXD output terminal ji D D 2D DDD Figure 12 6 Connections for audio over an Ethernet network 1 Audio_In C 7 AUTODOME Data In Out 2 Audio_In C 8 P105 P106 Connector 3 Earth Ground 9 Audio Out 4 Audio_Out RXD 5 Audio_Out TXD 6 Signal Ground 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Connection en 79 Notice Separate the audio cables from the AC power lines to avoid noise To configure audio on the camera refer to Basic Mode Audio page 86 or Audio page 106 Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 80 en Configuration AUTODOME 7000 12 12 1 Configuration System Requirements The camera requires specific software and hardware to allow a user to view live images and to configure camera settings over a TCP IP network These requirements are A computer with the Microsoft Windows XP Vista or Windows 7 operating system network access and the Microsoft Internet Explorer Web browser version 8 0 or later or A computer with Microsoft Windows XP Vista or Windows
102. ews on the cover door to 10 12 N m 90 105 in lbs 7 7 Attach Pendant to Arm and Tighten Notice Before attaching the AUTODOME Pendant visually inspect the dome and arm connectors for any blocked pin holes or bent pins 1 Tilt the bottom of the dome toward the pendant arm base and place the mounting hook located on top of the dome housing over the recessed hinge pin of the arm 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Installing the Pendant Arm Wall Corner and Mast Pole Mounts en 39 Figure 8 12 Attach Pendant to Arm 1 Tilt up 2 Hook and drop 2a Recessed Hinge Pin 2b Dome Connector 3 Rotate down to engage dome connector 4 Tighten the two 2 mounting screws to a minimum torque of 10 12 N m 90 105 in Ibs 2 Drop the dome housing down slightly to engage the dome housing hook on the Pendant Arm hinge pin allowing the dome to rotate around the pin 3 Rotate the dome housing down to a vertical position and gently push upward to engage the connector on top of the dome housing Caution If you feel any resistance when rotating the dome housing or when engaging the connector stop immediately and start over Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 40 en Installing the Pendant Arm Wall Corner and Mast Pole Mounts AUTODOME 7000 4 Hold t
103. f stop recording On Off 149 Turbo mode On activates turbo mode Off deactivates turbo mode Set Shot 901 999 Adds or removes Set adds preset to tour presets from tour Shot removes preset from tour 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc Bosch Security Systems Inc 850 Greenfield Road Lancaster PA 17601 USA www boschsecurity com Bosch Security Systems Inc 2014
104. fault setting Stream 2 is transmitted for alarm connections Bear this fact in mind when assigning the profile see Encoder Profile page 96 Number of destination IP address Specify the numbers of the IP addresses to be contacted in the event of an alarm The unit contacts the remote stations one after the other in the numbered sequence until a connection is made Destination IP address For each number enter the corresponding IP address for the desired remote station Destination password If the remote station is password protected enter the password here In this page you can save a maximum of ten destination IP addresses and hence up to ten passwords for connecting to remote stations If connections to more than ten remote stations are to be possible for example when initiating connections via higher ranking systems such as 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Configuration via IP Advanced Mode en 113 VIDOS or Bosch Video Management System you can store a general password here The camera can use this general password to connect to all remote stations protected with the same password In this case proceed as follows 1 Select 10 from the Number of destination IP address list field 2 Enter the address 0 0 0 0 in the Destination IP address field 3 Enter your chosen password in the Destination password field 4 Define this password as the user password for
105. he Pendant housing in position while tightening the two 2 5 mm Allen head mounting screws on top of the housing to 10 12 N m 90 105 in Ibs Caution You must tighten the two mounting screws to a minimum torque of 10 12 N m 90 105 in lbs to ensure a proper seal between the arm and the housing 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 8 2 Installing the Roof Parapet and Pipe Mounts en 41 Installing the Roof Parapet and Pipe Mounts Description This chapter details how to install an AUTODOME camera to a Roof Parapet or to a Pipe mount Any differences to the installation between these two mounting systems are noted The VGA ROOF MOUNT is a stationary mount intended for rooftop parapet vertical walls It is made of light weight aluminum with a corrosion resistant finish and is used for all Bosch AUTODOME cameras up to a rated load of 29 kg 64 Ib This mount can be fitted to the inside or outside of parapet walls and can swivel for ease of positioning and for servicing the camera Note that customers must purchase separately the VG4 A 9543 Pipe Mount to use on the end of the VGA ROOF MOUNT The end of the Pipe Mount that is meant to terminate into an enclosure is intended to be field installed and shall be marked or provided with instructions that identify the equipment necessary to maintain the environmental integrity of the enclosure In order to maintain the integrity of a
106. he camera for automatic Anti fog mode which activates when the video analytics in the camera detect fog and add light to the video image and then deactivates when the fog clears or the scene changes Select On to activate Anti fog mode on a continuous basis The camera operates in this mode until a user deactivates the mode The video image on the LIVE page may become lighter Select Off to deactivate the mode The video image on the LIVE page may become darker Lens Settings Autofocus Continuously adjusts the lens automatically to the correct focus for the sharpest picture One Push default commonly called Spot Focus activates the Auto Focus feature after the camera stops moving Once focused Auto Focus is inactive until the camera is moved again Auto Focus Auto Focus is always active Manual Auto Focus is inactive Focus polarity Normal default focus controls operate normally Reverse focus controls are reversed Focus speed Use the slider from 1 to 8 to control how fast the Auto focus will readjust when the focus becomes blurred Auto iris Automatically adjusts the lens to allow the correct illumination of the camera sensor This type of lens is recommended for use where there are low light or changing light conditions Constant default camera constantly adjusts to varying light conditions default If you select this option the camera makes the following changes automatically Gai
107. he unit You can enable this service here To do this you must have an account with DynDNS org and you must have registered the required host name for the unit on that site Notice Information about the service registration process and available host names can be found at DynDNS org Provider The value in this field defaults to dyndns org Select another option as necessary Host name Enter the host name registered on DynDNS org for the camera here User name Enter the user name you registered at DynDNS org here Password Enter the password you registered at DynDNS org here Force registration now You can force the registration by transferring the IP address to the DynDNS server Entries that change frequently are not provided in the Domain Name System It is a good idea to force the registration when you are setting up the device for the first time Only use this function when necessary and no more than once a day to avoid the possibility of being blocked by the service provider To transfer the IP address of the camera click the Register button Status The status of the DynDNS function is displayed here for information purposes You cannot change any of these settings Notification mail Select On to set the system to provide email notification of domain registration 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 14 44 14 45 Configuration via IP Advanced Mode
108. hnical data 148 User Command Table 149 Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 6 en Safety EN AUTODOME 7000 1 Safety EN 1 1 About this Manual This manual has been compiled with great care and the information it contains has been thoroughly verified The text was complete and correct at the time of printing Because of the ongoing development of products the content of the manual may change without notice Bosch Security Systems accepts no liability for damage resulting directly or indirectly from faults incompleteness or discrepancies between the manual and the product described 1 2 Legal Information Copyright This manual is the intellectual property of Bosch Security Systems Inc and is protected by copyright All rights reserved Trademarks All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly 1 3 Safety Precautions Danger Indicates a hazardous situation which if not avoided will result in death or serious injury Warning Indicates a hazardous situation which if not avoided could result in death or serious injury Caution Indicates a hazardous situation which if not avoided could result in minor or moderate injury Notice Indicates a situation which if not avoided could result in damage to the equipment or gt D D environment or data loss 1
109. ice logo fields Show VCA metadata When video content analysis VCA is activated additional information is displayed in the live video stream For example in Motion mode the sensor areas for motion detection are marked Show VCA trajectories When video content analysis VCA is activated check this item to show additional information that traces the path of objects Show overlay icons Select this checkbox to show overlay icons on the live video image Video player Select the desired video player from the list in the drop down box Options are Auto detect default Bosch Video SDK Bosch Autoload Decoder JPEG JPEG size You can specify the size of the JPEG image on the LIVE page Options are Small Medium Large 720p 1080p and Best possible default JPEG interval You can specify the interval at which the individual images should be generated for the M JPEG image on the LIVE page JPEG quality You can specify the quality at which the JPEG images appear on the LIVE page 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 14 8 Configuration via IP Advanced Mode en 93 LIVE Functions On this page you can adapt the functions on the LIVE page to your requirements You can choose from a variety of different options for displaying information and controls 1 Check the box for the items that are to be made available on the LIVE page The selected items a
110. ified IP addresses after each reboot after a connection breakdown or after a network failure Notice In the default setting Stream 2 is transmitted for automatic connections Bear this fact in mind when assigning the profile see Encoder Profile page 96 Audio Select On to activate audio alarms 14 32 VCA The camera has integrated video content analysis VCA which can detect and analyze changes in the signal on the basis of image processing Such changes can be due to movements in the camera s field of view You can select various VCA configurations and adapt these to your application as required The Silent MOTION Configuration is active by default In this configuration metadata is created to facilitate searches of recordings however no alarm is triggered 1 Select a VCA configuration and make the required settings 2 If necessary click the Default button to return all settings to their default values Intelligent DNR Digital Noise Reduction IVA VCA controls the iDNR feature which reduces noise based on motion activity in the scene When there is no motion in the preset scene noise reduction is increased When there is motion detected in the preset scene noise reduction is decreased to reduce bandwidth and optimize storage space To disable the iDNR feature select the OFF option in the VCA configuration field To enable iDNR select a Profile 1 16 or Silent VCA in the VCA configuration field If you sele
111. ilt or both or moving between selected preset positions Continuous Guard Tours Guard Tours are a very effective way of monitoring the entire scene however if not configured properly continuous Guard Tours can reduce the service life of your camera considerably Continuous Guard Tours should be used in applications where the tours are required to run for a fixed duration during the day not more than twelve hours day Additionally for best results the continuous guard tour should be used in scenes with sufficient illumination levels 50 lux or better should be at least 60 seconds in duration and should have a smooth pan tilt path without erratic stops and starts with the lens set at a wide angle infinity focus The tour should also include at least 10 of tilt movement Preset Tours For scenarios that require the camera to be in continuous motion for most of the day Bosch recommends that you set the camera in Preset Tour mode moving between a desired set of presets For best results always ensure that each preset has a dwell time of at least 5 seconds Notice Presets should be saved with One Push Spot Focus only Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 142 en Operation AUTODOME 7000 2 Scene Illumination and Focus Settings Your camera uses a high sensitivity image sensor and a high quality lens with a precise drive train control to maintain the best focus of the
112. image The Autofocus mechanism tries continuously to make the image details appear sharp Under low light and low contrast scenarios the Autofocus algorithm may not be able to find the correct focus points because of the lack of detail in the scene In this case it will keep driving the focus motor to find the best focus If this state continues for long the focus mechanism of your camera could be damaged beyond repair For best results maintain the scene illumination visible light and or IR illumination to a level that allows the camera to easily resolve the details in the scene The illumination requirements are site specific and should be verified during camera installation and configuration For best camera performance the scene should have at least 50 lux of illumination For scenes where sufficient lux level cannot be maintained the camera should be used with One Push Spot Focus and you should avoid using continuous Guard Tours 3 Power over Ethernet PoE Use the recommended Bosch High PoE 60W Midspan sold separately from the camera between the camera and your PoE network Improper network connection can result in intermittent camera reboots If the camera reboots frequently test your camera with another power supply If you choose to use a PoE switch ensure that the switch can support PoE IEEE 802 3at class 4 standard devices to optimize its power management and that the switch meets requirements for power draw for th
113. in which case the user will be required to correct the interference at his expense Intentional or unintentional modifications not expressly approved by the party responsible for compliance shall not be made Any such modifications could void the user s authority to operate the equipment If necessary the user should consult the dealer or an experienced radio television technician for corrective action The user may find the following booklet prepared by the Federal Communications Commission helpful How to Identify and Resolve Radio TV Interference Problems This booklet is available from the U S Government Printing Office Washington DC 20402 Stock No 004 000 00345 4 Informations FCC et ICES mod les utilis s aux Etats Unis et au Canada uniquement Ce produit est conforme aux normes FCC partie 15 la mise en service est soumises aux deux conditions suivantes cet appareil ne peut pas provoquer d interf rence nuisible et cet appareil doit pouvoir tol rer toutes les interf rences auxquelles il est soumit y compris les interf rences qui pourraient influer sur son bon fonctionnement 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 1 6 1 7 Safety EN en 11 AVERTISSEMENT Suite diff rents tests cet appareil s est r v l conforme aux exigences impos es aux appareils num riques de Classe A en vertu de la section 15 du r glement de la Commission f
114. ing the camera To install the SD card follow these steps Caution Risk of electrostatic discharge Use proper CMOS MOS FET handling precautions and observe proper ESD safety precautions such as wearing grounded wrist straps to avoid electrostatic discharge Warning Bosch recommends disconnecting power to the camera while adding or removing an SD card 1 Follow the steps in one of these sections depending on the type of camera mount Remove the bubble from an in ceiling housing page 68 or Remove the bubble from a pendant housing page 68 2 Locate the SD card slot item one in the figure below Figure 6 1 Camera cross section with SD card slot 3 Orient the card so that the side with the golden contacts faces away from the dome and towards the housing The contacts should be at the top as you hold the SD card 4 Slide the SD card into the slot Press down the end of the SD cards until you hear a click and the card locks into place Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 22 en Installing the Optional SD Card AUTODOME 7000 5 Follow the steps in one of these sections depending on the type of camera mount Replace the bubble in an in ceiling housing page 70 or Replace the bubble in a pendant housing page 70 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 6 Mount Power Supply Box Wall Mast Pole an
115. ing the cover door Attach the supplied 3 pin power plug to the incoming high voltage power wires in the box Refer to connector P101 in the table above and to the image below for an illustration of these connections Figure 8 4 Incoming 115 230 VAC power supply 4 5 Attach the ground wire to the grounding screw Connect three wires to the P107 Power Out connector to route the 24 VAC power supply to the VG4 PAO Power Supply Box Connect the first wire to pin 5 HN Heater Neutral connector Connect the second wire to pin 4 HL Heater Line connector Connect the third wire to pin 3 Earth Ground connector Refer to connector P107 in the table above and to the image below for an illustration of these connections Figure 8 5 Outgoing 24 VAC power supply 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Installing the Pendant Arm Wall Corner and Mast Pole Mounts en 31 Warning Ensure that you connect the outgoing power supply wires to the P107 heater connectors HN and HL The heater power XF103 fuse can handle a higher amperage 3 15 A than the camera power XF102 fuse 2 0 A 6 Route the 24 VAC outgoing power supply wires into the VG4 PAO power supply box through the conduit fitting on the left side of the box 7 Cut and trim the 24 VAC power and ground wires with sufficient slack to reach their connector terminal in the box but not so long as to be pi
116. inges release the top hinge pin to engage its mating hinge on the power box Then release the bottom hinge pin from the Hinge Pin Stop to lock the Pendant Arm to the Power Supply Box Warning Serious injury or death can occur if the hinge pins of the Pendant Arm are not fully engaged locked to the Power Supply Box Exercise caution before releasing the Pendant Arm 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Installing the Pendant Arm Wall Corner and Mast Pole Mounts en 33 7 5 Make Connections in the Power Supply Box Figure 8 8 Pendant Arm connections to Power Supply Box 1 Attach the earth ground wire item 1 in the illustration above to the grounding screw on the left side of the power box 2 Connect the 6 pin Control In Out Plug installed previously to its mating connector P106 in the power box 3 Connect the 6 pin Control to Dome Plug from the Pendant Connector Harness to its mating connector P105 in the power box 4 Connect the 5 pin 24 VAC to Dome Plug from the Pendant Connector Harness to its corresponding color mating connector P107 on the right side of the box 5 To connect alarm inputs and relay outputs connect the 4 pin Alarms Out the 6 pin Alarms In and the 7 pin Relay connectors from the Pendant Connector Harness to their mating connectors installed previously to the incoming alarm wires 6 Connect the 3 pin Power In Plug installed prev
117. iously to its mating connector P101 on the left side of the box 7 Connect the incoming RJ45 video connector installed previously to its mating connector from the Pendant Connector Harness 8 Attach the grounding strap of the Pendant Arm to the Power Supply Box 9 After making the harness connections to the Power Supply Box rotate the Pendant Arm to close and seal the Power Supply Box and tighten the two 2 captive screws to 10 12 N m 90 105 in lbs 10 Refer to Attach Pendant to Arm and Tighten page 38 to continue the installation procedure Notice After all wiring is complete close the cover door and tighten the two 2 captive screws on the cover door to 10 12 N m 90 105 in lbs to ensure the Power Supply Box is watertight Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 34 en Installing the Pendant Arm Wall Corner and Mast Pole Mounts AUTODOME 7000 7 6 Installing the VGA PEND WPLATE This section provides instructions to install a wall corner or mast mount with the VGA PEND WPLATE Mounting Plate instead of a Power Supply Box Caution You must route the main power supply through a 120 230 VAC transformer VG4 PSU1 or VG4 PSU2 power supply box before connecting the power to a 24 VAC AUTODOME camera Warning A stud diameter of 6 4 mm 1 4 inch to 8 mm 5 16 inch able to withstand a 120 kg 265 Ib pull out force is recommended The mounting material must be
118. is file with any text editor or the standard Office software File for event log 1 Enter the path for saving the event log here 2 If necessary click Browse to find a suitable directory Save system log Check this option to save system messages in a text file on your local computer You can then view edit and print this file with any text editor or the standard Office software File for system log 1 Enter the path for saving the system log here 2 If necessary click Browse to find a suitable directory Advanced Mode Camera Installer Menu The following options are available only for HD cameras Base frame rate This option allows you to set the frame rate that the camera uses to transmit video Select either 25 ips or 30 ips If you select 25 ips the camera will stream video at 25 or 50 ips If you select 30 ips the camera will stream video at 30 or 60 ips depending on the option selected in the Encoder Stream Max frame rate This option determines the maximum frame rate that the camera streams video Select one of the following options Max Frame Rate Option Available Streaming Options 25 30 ips up to 1920 x 1080 H 264 MP 720p25 30 Fixed H 264 MP 1080p25 30 Fixed 50 60 ips up to 1280 x 720 H 264 MP 720p50 60 Fixed Notice Changing the Base frame rate or Max frame rate A change to the Base frame rate or to the Max frame rate parameter requires a reboot of the HD camera The reboot proces
119. ivate the recording scheduler Running recordings are interrupted and the configuration can be changed Recording status The graphic indicates the recording activity of the camera You will see an animated graphic while recording is taking place Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 112 en Configuration via IP Advanced Mode AUTODOME 7000 14 29 Recording Status Certain details on the recording status are displayed here for information purposes You cannot change any of these settings If an error occurs during recording the Status line for the recording may display informational icons that provide additional information when you point to them with your mouse 14 30 Advanced Mode Alarm Alarm Alarm Connections VCA Virtual Masks Audio Alarm Alarm E Mail Alarm Task Editor Alarm Rules 14 31 Alarm Connections You can select how the camera responds to an alarm In the event of an alarm the unit can automatically connect to a pre defined IP address You can enter up to ten IP addresses to which the camera will connect in sequence in the event of an alarm until a connection is made Connect on alarm Select On so that the camera automatically connects to a predefined IP address in the event of an alarm By setting Follows input 1 the unit maintains the connection that has been automatically established for as long as an alarm exists on alarm input 1 Notice In the de
120. ivided into 858 square fields Each of these fields can be activated or deactivated individually Notice Select only those areas for reference monitoring in which no movement takes place and that are always evenly lit as false alarms could otherwise be triggered 1 Click Select Area to configure the sensor fields A new window will open 2 If necessary click Clear All first to clear the current selection fields marked yellow 3 Left click the fields to be activated Activated fields are marked yellow 4 If necessary click Select All to select the entire video frame for monitoring 5 Right click any fields you wish to deactivate 6 Click OK to save the configuration 7 Click the close button X in the window title bar to close the window without saving the changes 14 33 Virtual Masks Virtual masks allow users to mask parts of the scene which should not be considered for flow analysis to trigger Intelligent Tracking This allows users to mask background motion in the scene such as moving trees pulsating lights busy roads etc To create a virtual mask 1 Select the number of the Virtual mask In the video preview window a dark grey rectangle appears with the text Mask x where x is the number of the mask 2 Select the mask with your mouse Move the mouse to position the mask over the area of the view that you want to mask and then click Set The text VM Configuration active appears in the View Con
121. l counter allows the installer to easily verify that the camera installation fulfills any regulatory or specific customer requirements for example calculating the pixel resolution of the face of a person passing a doorway monitored by the camera Advanced Mode Recording Y Recording Storage Management Recording Profiles Maximum Retention Time Recording Scheduler Recording Status Storage Management You can record the images from the camera on various local storage media user supplied SD SDHC or SDXC memory card or on an appropriately configured iSCSI system It is also possible to let the VRM Video Recording Manager control all recording with accessing an iSCSI system This is an external program for configuring recording tasks for video servers For further information please contact your local customer service at Bosch Security Systems Inc Device manager If you activate the Managed by VRM option in this screen the VRM Video Recording Manager will manage all recording and you will not be able to configure any further settings here Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 108 en Configuration via IP Advanced Mode AUTODOME 7000 Caution Activating or deactivating VRM causes the current settings to be lost they can only be restored through reconfiguration Recording media Select the required recording media here so that you can then activate them and configur
122. larm gt VCA Refer to the VA 5 60 Operation Manual for specific information If the Show VCA metadata option is selected in LIVE Functions from the SETTINGS page select Advanced Mode gt Web Interface gt LIVE Functions the live view will show the following metadata objects in the LIVE page view Objects in motion are initially identified in the video Actively tracked object in motion are identified in the video When an object in motion is lost a diamond appears designating the area where the target was lost Several reasons may cause the Intelligent Tracking to stop tracking a target The target has stopped moving while being followed by Intelligent Tracking The target has moved behind a static object in the scene In these instances Intelligent Tracking switches to the IDLE mode pink eye icon and waits for the target to reappear in the scene The camera will restart tracking if a target starts moving in the same area where the initial target stopped moving or if the camera detects an object moving along the last known trajectory Recommended Use of Your Camera Bosch recommends that you consider the following in order to optimize the life of your Bosch camera 1 Guard Tours and Preset Tours With the AUTODOME 7000 Series you can cover a full 360 view using continuous Guard Tours or Preset Tours Depending on the type of camera tour selected your camera might be either in continuous motion pan t
123. lecting different values for the fields below In this case the name of the user mode changes to Custom White Balance Adjusts the color settings to maintain the quality of the white areas of the image ATW allows the camera to continuously adjust color reproduction AWB Hold places the ATW on hold and saves the color settings Extended ATW default allows the camera to constantly adjust for optimal color reproduction Manual Red and Blue gain can be manually set to a desired position Sodium Lamp Auto Automatically adjusts for sodium vapor light to restore objects to their original color Sodium Lamp Optimizes the sodium vapor light to restore objects to their original color Red Gain The red gain adjustment offsets the factory white point alignment reducing red introduces more cyan Blue Gain The blue gain adjustment offsets the factory white point alignment reducing blue introduces more yellow It is only necessary to change the white point offset for special scene conditions Saturation The percentage of light or color in the video image HD only Values range from 60 to 200 the default is 110 Color hue The degree of color in the video image HD only Values range from 14 to 14 the default is 8 Gain control Adjusts the automatic gain control AGC Automatically sets the gain to the lowest possible value needed to maintain a good picture AGC default electronically brightens dark sce
124. length of 5 inches 12 7 cm You must use Teflon tape for thread sealing compound All screws shall be tightened securely 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Installing the Roof Parapet and Pipe Mounts en 51 min Figure 9 10 Pipe Mount 1 Gasket 2 Flange 3 Cap 1 Before installing the Top Mounting Flange ensure there is an adequate opening in the ceiling or mounting structure for the wires to pass through 2 Secure the pipe Flange with supplied gasket to the ceiling or other supporting structure using four 4 10 mm 3 8 inch diameter fasteners Notice Each fastener must have a minimum pullout strength of 275 kg 600 Ibs The mounting material must be able to withstand this pull out force For example 19 mm 3 4 inch minimum for plywood 3 Attach pipe not supplied to the Top mounting Flange Warning You must thread the pipe onto the Top mounting Flange until it is tight Failure to do so can result in damage serious injury or death 4 Route the power video control and alarm wires through the Top Mounting Flange and down the pipe 5 Wrap at least five layers of Teflon tape around the threads 6 Apply the supplied thread sealant to the threads on the Pipe Make sure all surfaces are clean and dry Apply a bead of sealant completely around the leading threads of the male fitting Force the adhesive into the thr
125. lt setting is 1 60 second for NTSC and 1 50 for PAL cameras The range of settings is from 1 1 to 1 10000 Auto SensUP limit This is the maximum shutter speed when Auto SensUP Frame Integration is active The default is 1 4 The range of settings is from 1 4 to 1 30 Shutter limit The camera tries to hold this shutter value as long as sufficient ambient light is available in the scene Settings range from 1 1 to 1 10000 The default value is 1 2000 for all modes except Motion default 1 500 Backlight compensation Optimizes the video level for the selected area of the image Parts outside this area may be underexposed or overexposed Select On to optimize the video level for the central area of the image The default setting is Off High Sensitivity Adjusts the level of intensity or lux within the image HD only Select from Off or On Note In Black and White Night mode low light situations High Sensitivity turns on automatically Stabilization This feature is ideal for cameras mounted on a pole or mast or on another location that shakes frequently Select On to activate the video stabilization feature if available on your camera that reduces camera shake in both the vertical and horizontal axis The camera compensates for the movement of the image by up to 2 of the image size Select Auto to activate the feature automatically when the camera detects vibration Select Off to deactivate the feature Note This
126. lug Moving Disconnect the power before moving the unit Move the unit with care Excessive force or shock may damage the unit and the hard disk drives Outdoor signals The installation for outdoor signals especially regarding clearance from power and lightning conductors and transient protection must be in accordance with NEC725 and NEC800 CEC Rule 16 224 and CEC Section 60 Permanently connected equipment Incorporate a readily accessible disconnect device in the building installation wiring Pluggable equipment Install the socket outlet near the equipment so it is easily accessible Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 10 en Safety EN AUTODOME 7000 High PoE or PoE 802 3at Never supply power via the Ethernet connection High PoE or PoE when power is already supplied via the power connector unless implementing an Auxiliary Power application described in the section Connection in Applications page 11 Power lines Do not locate the camera near overhead power lines power circuits or electrical lights nor where it may contact such power lines circuits or lights SELV All the input output ports are Safety Extra Low Voltage SELV circuits SELV circuits should only be connected to other SELV circuits Because the ISDN circuits are treated like telephone network voltage avoid connecting the SELV circuit to the Telephone Network Voltage TNV circuits Video loss Video lo
127. m Inputs The camera provides seven alarm inputs Each input can be activated by dry contact devices such as pressure pads passive infra red detectors door contacts and similar devices The table below summarizes the size and distance wires Wire Size Maximum Distance AWG mm feet meters 22 0 644 500 152 4 18 1 024 800 243 8 Table 12 1 Alarm wire guide You wire alarms either Normally Open N O or Normally Closed N C and must program the alarm inputs N O the default or N C through the SETTINGS page The camera incorporates two types of alarms Non supervised and Supervised In addition to transmitting an alarm condition a supervised alarm also transmits a tamper condition Depending on how the alarm is configured a short or a break in the alarm s circuit can trigger the tamper signal Configuring Supervised Alarms inputs 1 and 2 To configure Alarm 1 or 2 pin 5 or 6 for supervision you must install a 2 2 K end of line resistor in the circuit Then you program the alarms through the Settings menu to either Normally Open N O or Normally Closed N C Notice Only Alarms 1 and 2 pins 5 or 6 can be configured for supervision Once a supervised alarm is programmed it does not need to be enabled to indicate a tamper condition Configuring a Normally Open Supervised Alarm 1 Install a 2 2 K end of line resistor in the alarm circuit 2 Connect the alarm wires to input 1 or 2 pin 5
128. n Options with H 264 MP 1080p25 30 Fixed selected for Stream 1 Copy Stream 1 H 264 MP SD H 264 MP 720p8 10 Fixed H 264 MP 1080p4 5 Fixed H 264 MP upright cropped H 264 MP D1 4 3 cropped Options with H 264 MP 720p50 60 Fixed selected for Stream 1 Copy Stream 1 H 264 MP SD H 264 MP 720p6 7 Fixed H 264 MP upright cropped H 264 MP D1 4 3 cropped Options with H 264 MP 720p25 30 Fixed selected for Stream 1 H 264 MP SD H 264 MP 720p25 30 Fixed H 264 MP upright cropped H 264 MP D1 4 3 cropped H 264 MP 1280x960 cropped Option with H 264 MP SD selected for Stream 1 H 264 MP SD Non recording profile Select one of the following profiles for each stream Preview Click the Preview button to open a small static preview window for each stream To enlarge the preview and view live video click the 1 1 Live View button JPEG stream Select the resolution frame rate and image quality parameters for the M JPEG stream Resolution Select the appropriate resolution Max frame rate Select one of the following frame rates to be the maximum 5 10 15 20 25 or 30 ips Picture quality This setting allows you to adjust the image quality Use the slide bar to choose a quality between Low and High Note The M JPEG frame rate can vary depending on system loading See also Encoder Profile page 96
129. n Control switches to AGC Shutter Speed switches to default Manual camera must be manually adjusted to compensate for varying light conditions Iris polarity Capability to reverse the operation of the iris button on the controller Normal default iris controls operate normally Reverse iris controls are reversed Auto iris level Increases or decreases brightness according to the amount of light Type a value between 1 and 15 Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 104 en Configuration via IP Advanced Mode AUTODOME 7000 Maximum zoom speed Controls the zoom speed Zoom polarity Capability to reverse the operation of the zoom button on the controller Normal default zoom controls operate normally Reverse zoom controls are reversed Digital zoom Digital zoom is a method of decreasing narrowing the apparent angle of view of a digital video image It is accomplished electronically without any adjustment of the camera s optics and no optical resolution is gained in the process Select Off to disable or On to enable this feature The default setting is On 14 17 PTZ Settings Auto pan speed Continuously pans the camera at a speed between right and left limit settings Type a value between 1 and 60 expressed in degrees inclusive The default setting is 30 Inactivity Selects the time period the dome must be not controlled until the inactivity e
130. n Stop The power box Cover Door provides a Hinge Pin Stop to hold the bottom hinge open while attaching the door Power Supply Box 5 Hold Hinge Pin Open Cover Door 6 Open Position Align Top Hinge 7 Hinge Pin Stop Align Bottom Hinge Open the top hinge by pushing its pin lever outward and holding it open Note Both Hinge Pins must be fully compressed to open unlock the female hinges of the Cover Door before proceeding to the next step While holding the top hinge pin open position the Cover Door to the Power Supply Box and align its hinges Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 48 en Installing the Roof Parapet and Pipe Mounts AUTODOME 7000 4 When the hinges are aligned release the top hinge pin to engage its mating hinge on the power box Then release the bottom hinge pin from the Hinge Pin Stop to complete attaching the Cover Door to the Power Supply Box Notice After all wiring is complete close the cover door and tighten the two 2 captive screws on the cover door to 10 12 N m 90 105 in lbs to ensure the Power Supply Box is watertight 8 4 Installing the VGA ROOF MOUNT This section details the installation steps for the Roof Parapet Mount If you are installing a pipe mount refer to nstalling the VG4 A 9543 Pipe Mount page 50 for instructions Figure 9 6 VGA ROOF MOUNT 1 Determine
131. n again to stop recording 2 To change the storage location for the recorded video select Advanced Mode gt Recording gt Storage Management from the SETTINGS page Image Resolution Sequences are saved at the resolution that has been preset in the configuration for the encoder see Basic Mode Network page 85 Processor Load If the camera is accessed via the Web browser you will see the processor load indicator in the top left of the window next to the manufacturer s logo e 1 Other 9 You can obtain additional information to help when you troubleshoot or fine tune the unit The values indicate the proportions of the individual functions on the encoder load shown as percentages gt Move the cursor over the graphic indicator Some additional numerical values are also displayed Accessing Recorded Video from the Recordings Page PLAYBACK Click Recordings to access the Recordings page from the LIVE page or SETTINGS page the Recordings link is only visible if a storage medium has been selected AUTODOME 7000 HD LIVEPAGE gt PLAYBACK SETTINGS e AETA e catas Figure 16 2 Playback page Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 138 en Operation AUTODOME 7000 Selecting Recordings All saved sequences are displayed in a list A track number is assigned to each sequence Start time and stop time recording duration number of alarms and recording t
132. n on site Caution Before launching the firmware upload make sure that you have selected the correct upload file Uploading the wrong files can result in the unit no longer being addressable in which case you must replace the unit You should never interrupt the installation of firmware An interruption can lead to the flash EPROM being incorrectly programmed This in turn can result in the unit no longer being addressable in which case it will have to be replaced Even changing to another page or closing the browser window leads to an interruption Upload 1 Enter the full path of the file to upload or click Browse to navigate to the required firmware file fw 2 Make certain that the file to be loaded comes from the same unit type as the unit you want to configure 3 Next click Upload to begin transferring the file to the unit The progress bar allows you to monitor the transfer 4 Click OK to the warning message to continue the firmware upload or Cancel to stop the upload The page displays a progress bar as the firmware is uploaded Note Once the progress bar reaches 100 the system opens the reset page Allow the reset page to complete its action Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 130 en Configuration via IP Advanced Mode AUTODOME 7000 Once the upload is complete the new configuration is activated The time remaining is shown by the message going to reset Recon
133. n place to provide the IP54 protection Refer to Replace the trim ring optional In ceiling models page 69 for step by step installation instructions 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Installing the In Ceiling Mount en 65 Figure 10 8 In ceiling IP54 Rating Installation Diagram Sz 1 White Trim Ring factory installed on dome bubble Inner Ring 2 Black Trim Ring supplied in the 6 Ceiling IP54 housing Gasket shipping box of the camera 3 Bubble 7 In ceiling housing 4 Trim Ring Gasket 1 Place the gasket provided in the shipping box of the camera over the top of the in ceiling housing 2 Carefully slide the gasket down over the housing until it rests on the flange of the housing 9 8 Attach Housing to the Interface Box The In Ceiling Housing is attached to the Interface Box and secured by two 2 thumbscrews Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 66 en Installing the In Ceiling Mount AUTODOME 7000 Figure 10 9 Attach Housing to Interface Box 1 Insert the In ceiling housing through the hole in the ceiling to verify that the edge of the hole support the unit Then remove the housing from the hole 2 Align the ball studs of the In Ceiling Housing to the Stud Retainers on Interface Box and attach 3 Tighten the two 2 Thumbscrews to secure the
134. nched by or to obstruct closing the cover door 8 Attach the supplied 3 pin power plug to the incoming 24 VAC power wires in the box as illustrated below Figure 8 6 VG4 PAO Power Supply Box 1 Incoming 24 VAC Power Supply Wires from VG4 PSU1 VG4 PSU2 power supply box 2 Ground Wire 3 P101 Connector 4 Control Data and Video In Out Wires analog models only 9 Follow the instructions in Attach Pendant Arm to Power Supply Box page 32 to continue the installation Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 32 en Installing the Pendant Arm Wall Corner and Mast Pole Mounts AUTODOME 7000 7 4 Attach Pendant Arm to Power Supply Box The bottom hinge pin of the Pendant Arm is provided with a Hinge Pin Stop to hold the hinge open while attaching the arm to the Power Supply Box 1 Compress the bottom hinge pin by pushing the pin lever downward and rotating it behind the Hinge Pin Stop Figure 8 7 Pendant Arm to Power Box Hinge Alignment 2 Open the top hinge by pushing its pin lever up and holding it Notice Both Hinge Pins must be fully compressed to open unlock the hinges of the Pendant Arm and before proceeding to the next step 3 While continuing to hold the top hinge pin open and align the top and bottom hinges of the Pendant Arm to their mating points on the Power Supply Box See the illustration above 4 Once you have aligned the h
135. necting in seconds The unit reboots automatically once the upload has successfully completed Download 1 Click the Download button A dialog box opens 2 Follow the on screen instructions to save the current settings Configuration You can save configuration data for the camera on a computer and then load saved configuration data from a computer to the unit SSL certificate To be able to work with an SSL encrypted data connection both ends of a connection must hold the relevant certificates You can upload the SSL certificate comprising one or multiple files onto the camera If you wish to upload multiple files onto camera you must select them consecutively 1 Enter the full path of the file to upload or click Browse to select the required file 2 Next click Upload to begin transferring the file to the unit 3 Once all files have been successfully uploaded the unit must be rebooted In the address bar of your browser enter reset after the IP address of camera for example 192 168 0 10 reset The new SSL certificate is valid Maintenance log You can download an internal maintenance log from the unit to send it to Customer Service for support purposes Click Download and select a storage location for the file 14 53 Licenses You can enter the activation key to release additional functions or software modules Notice The activation key cannot be deactivated again and is not transferable to other units
136. nections in the Interface Box below the ceiling Refer to the Wire the Interface Box section below 4 Attach the remaining control data in out wires to their respective terminals in the Interface Box 5 Connect the Ethernet cable to its mating connector J101 in the Interface Box 6 Connect the 24 VAC power wires to the P101 connector in the Interface Box Connecting Alarm Inputs and Outputs gt To connect alarm inputs and outputs attach the supplied 6 pin Alarms In and the 4 pin Alarms Out connector plugs with flying lead wires to the appropriate incoming alarm wires Alarm Out 4 is a relay Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 62 en Installing the In Ceiling Mount AUTODOME 7000 1 2 3 PIN 4 1 ie 2 6 3 ORANGE 7 4 5 6 Figure 10 6 Alarm and relay connectors 1 4 pin Alarm 2 6 pin Alarm In 3 7 pin Relay Connector P104 Connector P102 Connector P103 Pin Description Pin Description Pin Description 1 Alarm Out 1 1 Alarm in 3 1 Alarm Out 4 Normally Open 2 Alarm Out 2 2 Alarm in 4 2 Alarm Out 4 COM 3 Alarm Out 3 3 Alarm in 5 3 Alarm Out 4 Normally Closed 4 Alarm Ground 4 Alarm in 6 4 Earth Ground 5 Alarm in 7 5 Analog Alarm 1 6 Alarm Ground 6 Analog Alarm 2 7 Ground For in ceiling mount only Low Voltage TTL 3 3V can also be used Connect the plugs to their mating
137. nes which may cause graininess in low light scenes Fixed no enhancement This setting disables the Max Gain Level option If you select this option the camera makes the following changes automatically Night Mode switches to Color Auto Iris switches to Constant Fixed Gain Use the slide to select the desired number for fixed gain The default is 2 Maximum Gain Level Controls the maximum value the gain can have during AGC operation To set the maximum gain level choose from Normal Medium High default AE response speed Select the speed of the response of auto exposure Options are Super slow Slow Medium default Fast Sharpness Adjusts the sharpness of the picture To set the sharpness use the slider to select a number The default is 12 Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 102 en Configuration via IP Advanced Mode AUTODOME 7000 Shutter Mode Off turns the Auto SensUP Off AutoSensUp increases camera sensitivity by increasing the integration time on the camera This is accomplished by integrating the signal from a number of consecutive video frames to reduce signal noise If you select this option the camera makes the following change automatically Auto Iris switches to Constant Shutter is disabled Shutter Adjusts the electronic shutter speed AES Controls the time period for which light is gathered by the collecting device The defau
138. ng the chalk or pencil mark as reference ensures that you align both screw slots Warning Trim ring can become deformed If the trim ring is not turned completely the screw slot on the trim ring will not be aligned with the screw slot in the housing You cannot see the screw slot in the housing when you are turning the screw in the slot in the trim ring You can turn the screw in the slot in the trim ring but miss the screw slot on the housing Forcing the screw into the trim ring without the screw going into the screw slot in the housing can deform the ring 4 Erase the chalk or pencil mark if desired Replace the bubble in a pendant housing 1 Insert the bubble and trim ring assembly into the pendant housing 2 Rotate the assembly clockwise until it locks The latch mechanism makes a click when it locks 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 11 11 1 Connection en 71 Connection Connecting the AUTODOME camera to the PC 1 Install the camera according to the instructions in the appropriate Installation section of this manual 2 Connect an Ethernet cable from camera s RJ45 connector to a dedicated network switch to bypass the Local Area Network LAN 3 Connect the dedicated network switch to the RJ45 connector on the PC see option A below Notice The camera can also be connected directly to a PC using an Ethernet crossover cable with RJ45 conn
139. ng to PC snapshot and full screen display you must obtain MPEG Activex For the latest versions of the Video Client DirectX Oracle Java Virtual Machine and MPEG ActiveX software go to www boschsecurity com navigate to the product page for your camera and then download the software from the Software tab Notice Ensure that the graphics card is set to 16 bit or 32 bit color If you need further assistance contact your PC system administrator 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 12 2 Configuration en 81 Configuring the Camera To operate the camera in your network you must assign a valid network IP address to it If your network has a DHCP server the IP address of the camera defaults to the first address available If your network does not have a DHCP server the default IP address of the camera is 192 168 0 1 You may need to change this address if it conflicts with another device on your network Refer to Basic Mode Network page 85 for more information To configure the camera properly for your network you need the following information Unit IP address An identifier for the camera on a TCP IP network For example 140 10 2 110 is a valid syntax for an IP address Subnet mask A mask used to determine what subnet an IP address belongs to Gateway IP address A node on a network that serves as an entrance to another network Port An endp
140. ntelligent Tracking Pole and Mast Mounts Use a pendant arm with the Pole Mount Adapter VG4 A 9541 Do not attach a parapet mount to a pole or mast Use a pole designed specifically for CCTV cameras Do not use a tapered pole Do not use a pole that has signs or other equipment attached Consult EPA rating Wind load data to select an appropriate pole Roof Mounts Mount the camera in the most stable location on the roof Avoid locations affected by vibrations such as those caused by a rooftop air conditioner Use guy wires to stabilize the AUTODOME against strong winds Use the LTC 9230 01 Flat Roof Mount Adapter where appropriate This adapter is made specifically for AUTODOME roof applications Extreme Mount Applications Unique camera mounting applications that are impacted by extreme high winds heavy traffic or other conditions may require additional measures to stabilize the camera Contact a manufacturer that specializes in passive vibration suppression using either damping or isolation 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Installing the Optional SD Card en 21 Installing the Optional SD Card The camera can accept a customer supplied SDHC or SDXC memory card hereafter referred to as SD card for local storage The camera will not accept MicroSD cards Using an SD card is optional Ideally you should install the SD card before mount
141. oax alarms I O relay I O and fiber optic cabling Refer to the Connection page 71 chapter for required cable types and allowed lengths Warning Install external interconnecting cables in accordance to NEC ANSI NFPA70 for US application and Canadian Electrical Code Part CSA C22 1 for CAN application and in accordance to local country codes for all other countries Branch circuit protection incorporating a 20 A 2 pole Listed Circuit Breaker or Branch Rated Fuses are required as part of the building installation A readily accessible 2 pole disconnect device with a contact separation of at least 3 mm must be incorporated 24 VAC Class 2 power supply only 2 To install the In ceiling Mount verify that a minimum of 216 mm 8 5 in of air space above the ceiling is available Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 20 4 1 en Pre installation Checklist AUTODOME 7000 3 Ifyou plan to use the Intelligent Tracking feature refer to Using Intelligent Tracking page 139 before mounting the camera Stabilization Surveillance cameras are susceptible to vibrations caused by wind or vibrations emanating from the medium to which the camera is attached Cameras attached to a pole roof or toa bridge are especially vulnerable Bosch offers the following recommendations to stabilize an AUTODOME 7000 and to decrease the affects of vibration on transmitted images privacy masks and I
142. ofiles in which you want to copy the settings 4 For each profile click the Set button to save the settings in the unit Standard recording Here you can select the mode for standard recordings If you select Continuous the recording proceeds continuously If the maximum memory capacity is reached older recordings will automatically be overwritten If you select the Pre alarm option recording will only take place in the pre alarm time during the alarm and during the set post alarm time If you select Off no automatic recording takes place Caution You can specify limitations for overwriting older recordings in Continuous mode by configuring the retention time see Maximum Retention Time page 110 Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 110 en Configuration via IP Advanced Mode AUTODOME 7000 Standard profile From this field you can select the encoder profile to be used for recording see Encoder Profile page 96 Notice The recording profile can deviate from the standard setting Active profile and is only used during an active recording Pre alarm time You can select the required pre alarm time from the list field Post alarm time You can select the required post alarm time from the list field Post alarm profile You can select the encoder profile to be used for recording during the post alarm time see Encoder Profile page 96 The Standard profile option a
143. oid false alarms For this reason the total signal is divided into 13 tonal ranges mel scale Check or uncheck the boxes below the graphic to include or exclude individual ranges Threshold Set up the threshold on the basis of the signal visible in the graphic You can set the threshold using the slide control or alternately you can move the white line directly in the graphic using the mouse Sensitivity You can use this setting to adapt the sensitivity to the sound environment You can effectively suppress individual signal peaks A high value represents a high level of sensitivity Alarm E Mail As an alternative to automatic connecting alarm states can also be documented by e mail In this way it is possible to notify a recipient who does not have a video receiver In this case the camera automatically sends an e mail to a previously defined e mail address Send alarm e mail Select On if you want the unit to automatically send an alarm e mail in the event of an alarm Mail server IP address Enter the IP address of a mail server that operates on the SMTP standard Simple Mail Transfer Protocol Outgoing e mails are sent to the mail server via the address you entered Otherwise leave the box blank 0 0 0 0 SMTP user name Enter a registered user name for the chosen mailserver here SMTP password Enter the required password for the registered user name here Format You can select the data format of the alarm message
144. oint to a logical connection in TCP IP and UDP networks The port number identifies the use of the port for use through a firewall connection Notice Ensure that the network parameters of your cameras are available before you begin configuration The camera defaults are as follows P Address 192 168 0 1 or first available address see above Subnet Mask 255 255 255 0 Gateway IP Address 0 0 0 0 The following sections provide instructions about installing the software necessary to view images over an IP connection configuring the IP network settings and accessing the camera images from a Web browser The camera has a default IP address of 192 168 0 1 To change the IP address or any network settings you can use the Configuration Manager software or the 7000 Series server Notice Contact your local network administrator for a valid IP address Subnet Mask and a Gateway IP Address Using the Configuration Manager Configuration Manager is an optional network utility provided on the Bosch Security Systems Web site Use the Configuration Manager Manual to make any configuration changes Notice Depending on the PC network security settings the user may need to add the new IP address to the browser s trusted sites list for the controls to operate Using the 7000 Series Web Server To configure the camera using the 7000 Series server do the following 1 Set the IP address on the PC to 192 168 0 10 to ensure
145. on the unit responds to requests from the network and is automatically registered on the requesting computers as a new network device For example access to the unit can then be made using Windows Explorer without knowledge of the IP address of the unit Notice To use the UPnP function on a computer both the Universal Plug and Play Device Host and SSDP Discovery Service must be active in Windows XP and Windows 7 Quality of service The camera offers Quality of Service QoS configuration options to ensure fast network response to PTZ data and images Quality of Service QoS is the set of techniques to manage network resources QoS manages the delay delay variation jitter bandwidth and packet loss parameters to guarantee the ability of a network to deliver predictable results QoS identifies the type of data in a data packet and divides the packets into traffic classes that can be prioritized for forwarding Consult with your network administrator for assistance configuring the Audio Video Control and the Alarm video settings and to select the appropriate Post alarm time 14 46 Multicast In addition to a 1 1 connection between an encoder and a single receiver unicast the camera can enable multiple receivers to receive the video signal from an encoder simultaneously The device either duplicates the data stream itself and then distributes it to multiple receivers Multi unicast or it sends a single data stream to the network
146. onitor only displays images when an alarm is triggered If you select a particular video output and a split image is set for this output on the receiver you can also select from Decoder the decoder in the receiver that is to be used to display the alarm image Notice Refer to the destination unit documentation concerning image display options and available video outputs Decoder Select a decoder of the receiver to display the alarm image The decoder selected has an impact on the position of the image in a split screen For example you can specify via a VIP XD that the upper right quadrant should be used to display the alarm image by selecting decoder 2 Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 114 en Configuration via IP Advanced Mode AUTODOME 7000 SSL encryption The data for the connection for example the password can be securely transmitted with SSL encryption If you have selected the On option only encrypted ports are offered in the Remote port parameter Notice Please note that the SSL encryption must be activated and configured at both ends of a connection This requires the appropriate certificates to be uploaded onto the camera You can activate and configure encryption of the media data video and metadata on the Encryption page see Encryption page 128 Auto connect Select the On option to automatically re establish a connection to one of the previously spec
147. ons 59 9 3 Prepare Drywall Ceiling for Installation 59 9 4 Prepare Suspension Ceiling for Installation 59 9 5 Wire the Interface Box 61 9 6 Interface Box Connections 62 9 7 Installing the Ceiling IP54 Housing Gasket 64 9 8 Attach Housing to the Interface Box 65 9 9 Secure Housing to Ceiling 67 10 Preparing the Bubble 68 11 Connection 71 11 1 Connecting the AUTODOME camera to the PC 71 Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 4 11 2 11 3 11 4 11 5 11 6 12 12 4 12 2 12 3 13 13 1 13 2 13 3 13 4 13 5 13 6 13 7 14 14 1 14 2 14 3 14 4 14 5 14 6 14 7 14 8 14 9 14 10 14 11 14 12 14 13 14 14 14 15 14 16 14 17 14 18 14 19 14 20 14 21 14 22 14 23 14 24 14 25 14 26 14 27 14 28 14 29 14 30 14 31 en Table of Contents AUTODOME 7000 Power Cable and Wire Distances Guides 71 Ethernet Connections 72 Fiber Optic Ethernet Media Converter Optional 73 Alarms and Relay Connections 74 Audio Connections Optional 77 Configuration 80 System Requirements 80 Configuring the Camera 81 Configuring Audio Optional 84 Configuration via IP Basic Mode 85 Basic Mode Device Access 85 Basic Mode Date Time 85 Basic Mode Network 85 Basic Mode Encoder 86 Basic Mode Audio 86 Basic Mode Recording 86 Basic Mode System Overview 87 Configuration via IP Advanced Mode 88 Advanced Mode General 88 Identification 88 Password 88 Date Time 89 Display Stamping 90
148. or 6 and to the ground pin 7 at the camera 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Connection en 75 Figure 12 2 N O S Normally Open Supervised Connections 1 Dry Contact 3 Dome Connector 2 Alarm 1 or 2 only Pin 5 or 6 4 Ground Pin 7 3 From the Settings menu select Advanced Mode gt Interfaces gt Alarm Inputs select the Alarm Input and N O See the table below for contact and condition details AutoDome Programmed N O S Contact Alarm Condition Open Normal Closed Alarm Cut or brake Tamper Configuring a Normally Closed Supervised Alarm 1 Install a 2 2 K end of line resistor in the alarm circuit 2 Connect the alarm wires to input 1 or 2 pin 5 or 6 and to the ground pin 7 at the camera Figure 12 3 N C S Normally Closed Supervised Connections 1 Dry Contact 3 Dome Connector 2 Alarm 1 or 2 only Pin 5 or 6 4 Ground Pin 7 3 From the Settings menu select Advanced Mode gt Interfaces gt Alarm Inputs select the Alarm Input and N C See the table below for contact and condition details AutoDome Programmed N C S Contact Alarm Condition Open Alarm Closed Normal Short Tamper Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 76 en Connection AUTODOME 7000 Configuring Non supervised Alarm
149. or dusting with a cloth Use clean dry compressed air preferably from a spray can to remove any dust from the interior surface Warning Do not use alcohol based solutions to clean the bubble This will cause the polycarbonate to cloud and over time cause stress aging which makes the bubble brittle 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Maintenance en 147 Cleaning the Bubble Exterior The exterior of the bubble is hard coated for extra protection If cleaning becomes necessary only use cleaning solutions and cloths suitable for cleaning safety glass lenses Dry the bubble thoroughly with a dry nonabrasive cloth to prevent water spots Never scrub the bubble with any abrasive material or cleaners Bosch recommends cleaning the exterior of the bubble with NOVUS No 1 Plastic Clean amp Shine or equivalent according to manufacturer s instructions Refer to www novuspolish com to order or to find a local distributor Cautions Do Not clean bubbles in the hot sun or on very hot days Do Not use abrasive or highly alkaline cleaners on the bubble Do Not scrape the bubble with razor blades or other sharp instruments Do Not use Benzene Gasoline Acetone or Carbon Tetrachloride on the bubble Remove an SD card 1 Follow the steps in one of these sections depending on the type of camera mount Remove the bubble from an in ceiling housing page 68 or R
150. orage not completed If the information about recorded video is not cached a discovery procedure is started in order find all recorded video During this time the discovery symbol is shown While discovery is executed gaps might be shown in places which the discovery has not yet reached The gap will automatically be replaced by the true video as soon as the correct information is available Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 132 en Operation AUTODOME 7000 Maximum Number of Connections If you do not connect the unit may have reached its maximum number of connections Depending on the unit and network configuration each camera can have up to 50 Web browser connections or up to 100 connections via the Bosch Video Management System BVMS Protected AutoDome If the camera is password protected against unauthorized access the Web browser displays a corresponding message and prompts you to enter the password when you attempt to access protected areas Notice An AUTODOME 7000 Series offers the option to limit the extent of access using various authorization levels see the AUTODOME 7000 Series online help 1 Enter the user name and associated password in the corresponding text fields 2 Click OK If the password is entered correctly the Web browser displays the page that was called up Protected Network If a RADIUS server is employed in the network for managing access
151. orner or Mast pole mount Any differences to the installation between these two mounting systems are noted Route Wires and Attach Connectors Notice If you plan to route the power through an intermediate power supply box refer to Route Power through Intermediate Power Supply Box page 29 Power wires must be routed to the left front side of the Power Supply Box through a separate electrically earth grounded conduit All video control and alarm wires must be routed through a second electrically earth grounded conduit to the right side of the box Warning External interconnecting cables are to be installed in accordance to NEC ANSI NFPA70 for US application and Canadian Electrical Code Part CSA C22 1 for CAN application and in accordance to local country codes for all other countries Branch circuit protection incorporating a 20 A 2 pole Listed Circuit Breaker or Branch Rated Fuses are required as part of the building installation A readily accessible 2 pole disconnect device with a contact separation of at least 3 mm 0 12 in must be incorporated Making the Connections Notice Refer to the Connection page 71 chapter for wire specifications and distances 1 Route all video control and alarm wires through the earth grounded conduit fitting on the right side of the power box 2 Route the high voltage 115 230 VAC lines through the earth grounded conduit fitting on the left side of the box The Power
152. orresponds to Stream 2 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Configuration via IP Advanced Mode en 111 14 28 Recording Scheduler The recording scheduler allows you to link the created recording profiles with the days and times at which the camera s images are to be recorded in the event of an alarm You can link any number of 15 minute intervals with the recording profiles for each day of the week Moving the mouse cursor over the table displays the time below it This aids orientation In addition to the normal weekdays you can define holidays that are not in the standard weekly schedule on which recordings are to apply This allows you to apply a schedule for Sundays to other days with dates that fall on varying weekdays 1 Click the profile you want to link in the Time periods field 2 Click in a field in the table hold down the mouse button and drag the cursor over all the periods to be assigned to the selected profile 3 Use the right mouse button to deselect any of the intervals 4 Click the Select All button to link all time intervals to the selected profile 5 Click the Clear All button to deselect all of the intervals 6 When you are finished click the Set button to save the settings in the unit Holidays You can define holidays that are not in the standard weekly schedule on which recordings are to apply This allows you to apply a schedule for Sundays to
153. osition of the time overlay It can be displayed at the Top at the Bottom or at a position of your choice that you can then specify using the Custom option Or it can be set to Off for no overlay information 1 Select the desired option from the list 2 Ifyou select the Custom option additional fields are displayed where you can specify the exact position Position XY 3 Inthe Position XY fields enter the values for the desired position Display milliseconds If necessary you can also display milliseconds This information can be useful for recorded video images however it does increase the processor s computing time Select Off if you do not need to display milliseconds Alarm mode stamping Select On to display a text message overlay in the image in the event of an alarm It can be displayed at a position of your choice that you can then specify using the Custom option Or it can be set to Off for no overlay information 1 Select the desired option from the list 2 Ifyou select the Custom option additional fields are displayed where you can specify the exact position Position XY 3 Inthe Position XY fields enter the values for the desired position Alarm message Enter the message to be displayed in the image in the event of an alarm The maximum text length is 31 characters Title OSD Select On to continuously display sector or shot title overlays in the image Select Momentary to display sector or shot ti
154. other days with dates that fall on varying weekdays 1 Click the Holidays tab Any days that have already been selected will be shown in the table 2 Click the Add button A new window will open 3 Select the desired date from the calendar You can select several consecutive calendar days by holding down the mouse button These will later be displayed as a single entry in the table 4 Click OK to accept the selection The window will close 5 Assign the individual holidays to the recording profiles as described above Deleting Holidays You can delete holidays you have defined yourself at any time 1 Click the Delete button A new window will open 2 Click the date you wish to delete 3 Click OK The item will be deleted from the table and the window will close 4 The process must be repeated for deleting additional days Time periods You can change the names of the recording profiles 1 Click a profile and then the Rename button 2 Enter your chosen name and then click the Rename button again Activating the Recording After completing configuration you must activate the recording scheduler and start the recording Once recording is underway the Recording Profiles and Recording Scheduler pages are deactivated and the configuration cannot be modified You can stop the recording activity at any time and modify the settings 1 Click the Start button to activate the recording scheduler 2 Click the Stop button to deact
155. over to generate an alarm This is to prevent objects that are too small from triggering an alarm A minimum value of 4 is recommended This value corresponds to four sensor fields Debounce time 1 s MOTION only The debounce time is intended to prevent very brief alarm events from triggering individual alarms If the Debounce time 1 s option is activated an alarm event must last at least one second to trigger an alarm Select Area MOTION only The areas of the image to be monitored by the motion detector can be selected The video image is subdivided into 858 square fields Each of these fields can be activated or deactivated individually If you wish to exclude particular regions of the camera s field of view from monitoring due to continuous movement by a tree in the wind etc the relevant fields can be deactivated Click Select Area to configure the sensor fields A new window will open If necessary click Clear All first to clear the current selection fields marked yellow Left click the fields to be activated Activated fields are marked yellow If necessary click Select All to select the entire video frame for monitoring Right click any fields you wish to deactivate Click OK to save the configuration Click the close button X in the window title bar to close the window without saving the OP OV Od Ry changes Tamper detection You can reveal the tampering of cameras and video cables by means of various options Runa s
156. own Pipe threads Make sure all surfaces are clean and dry Apply a bead of sealant completely around the leading threads of the male fitting Force the adhesive into the threads to thoroughly fill all voids 10 Thread the Dome Cap onto the down pipe and tighten securely See the illustration below Warning You must thread the Dome Cap onto the Down Pipe until it is tight Failure to do so can result in damage serious injury or death Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 50 en Installing the Roof Parapet and Pipe Mounts AUTODOME 7000 Figure 9 9 Attach Dome Cap 1 Thread Sealant or tape 2 Dome Cap 11 Runa bead of RTV Silicon sealant around the down pipe Dome Cap interface to seal any gaps between the down pipe and the Dome Cap 12 Proceed to Wire the Pipe Interface Board page 52 Notice Use a guy wire to aid in stabilizing the Parapet Arm Replace the 1 4 inch cap screw with a threaded 1 4 inch stainless steel eye bolt not supplied Loop the guy wire through the eye bolt and attach both ends to anchor spots on the roof 8 5 Installing the VG4 A 9543 Pipe Mount This section details the installation steps for the VG4 A 9543 Pipe Mount If you are installing the Roof Parapet mount refer to Installing the VGA ROOF MOUNT page 48 for instructions Notice Customer must supply 1 1 2 inch NPS pipe threaded on both ends with a minimum
157. quipment UL 60950 1 UL Certification does not cover the performance or reliability of the security or signaling aspects of this product UL MAKES NO REPRESENTATIONS WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT Connection in Applications 24 VAC power source This unit is intended to operate with a limited power source The unit is intended to operate at 24 VAC if High PoE is not available User supplied wiring must be in compliance with electrical codes Class 2 power levels High Power over Ethernet High PoE This unit can by powered via High PoE To power the unit this way use only approved High PoE devices those offered or recommended by Bosch High PoE can be connected at the same time as a 24 VAC power supply If auxiliary power 24 VAC to camera and to heater and High PoE are applied simultaneously the camera usually selects auxiliary input 24 VAC and will usually draw minimal power from the Bosch High PoE midspan For pendant models used in outdoor applications that require heaters a Bosch High PoE 60W midspan NPD 6001A sold separately is required to power both the camera and its internal heaters For in ceiling or indoor pendant applications that don t require heater power standard PoE 802 3at midspans or switches can be used to power the camera Customer Support and Service If this unit needs service contac
158. r disconnect device for switching off the voltage for all units Power sources Operate the unit only from the type of power source indicated on the label Before proceeding be sure to disconnect the power from the cable to be installed into the unit For battery powered units refer to the operating instructions For external power supplied units use only the recommended or approved power supplies For limited power source units this power source must comply with EN60950 Substitutions may damage the unit or cause fire or shock For 24 VAC units voltage applied to the unit s power input should not exceed 10 or 28 VAC User supplied wiring must comply with local electrical codes Class 2 power levels Do not ground the supply at the terminals or at the unit s power supply terminals If unsure of the type of power supply to use contact your dealer or local power company Servicing Do not attempt to service this unit yourself Opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel Damage requiring service Unplug the unit from the main AC power source and refer servicing to qualified service personnel when any damage to the equipment has occurred such as the power supply cord or plug is damaged exposure to moisture water and or inclement weather rain snow etc liquid has been spilled in or on the equipment Bosch Security Systems Inc Ope
159. r follow these steps 1 Open the LIVE page and then click the Settings tab 2 Inthe left pane click Advanced Mode and then click Camera The Camera menu expands 3 Click Audio The Audio page appears The page displays the current video image in the small window next to the slide controls to help you verify the audio source and improve the Peak levels 4 Select the protocol in the Audio field to activate audio over IP Change the option to ON Notice The audio signal is sent in a separate data stream parallel to the video data and so increases the network load The audio data is encoded according to G 711 or L16 and requires an additional bandwidth of approximately 80 Kbit s for each connection If you wish to configure the input and output gain of the audio signals set the Line In and Line Out fields to suit your specific requirements Changes are effective immediately The current level is displayed next to the slide control to help do this Make sure that the display does not go beyond the green zone during modulation For more information refer to Audio page 106 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 13 Configuration via IP Basic Mode en 85 Configuration via IP Basic Mode 13 1 Basic Mode Device Access Camera name You can give the camera a name to make it easier to identify The name makes the task of administering m
160. r the power supply box based on its voltage and current consumption You may choose to route the main power supply through an intermediate power supply box VG4 PSU1 or VG4 PSU2 before connecting the power to the pendant arm power supply box VG4 PAO Caution Select a rigid mounting location to prevent excessive vibration to the camera 2 Use only UL listed liquid tight strain reliefs for conduits to the Power Supply Box to ensure that water cannot enter the box You must use water tight conduits and fittings to meet NEMA 4 standards 3 Purchase the appropriate mounting hardware to use depending on the location of the camera either wall mount corner mount or mast pole mount If your application contains a Power Supply Box refer to Mount Power Supply Box Wall Mast Pole and Corner Mounts page 23 If you are using the Mounting Plate with a 24 V AUTODOME camera refer to Installing the VGA PEND WPLATE page 34 Warning For units intended to be installed outdoors All wiring power and I O cabling connecting to the unit must be routed separately inside different permanently earthed metal conduits not supplied Warning To minimize the potential for corrosion on the housing use only Bosch hardware and mounts See number 5 Installation in a corrosive environment in the section Recommended Use of Your Camera page 141 for more information 1 Install all external wiring including power control video c
161. ration Manual 2014 04 2 0 F 01U 283 679 8 1 5 en Safety EN AUTODOME 7000 an object has fallen into the unit unit has been dropped or the unit cabinet is damaged unit exhibits a distinct change in performance unit does not operate normally when the user correctly follows the operating instructions 13 Replacement parts Be sure the service technician uses replacement parts specified by the manufacturer or that have the same characteristics as the original parts Unauthorized substitutions may cause fire electrical shock or other hazards 14 Safety check Safety checks should be performed upon completion of service or repairs to the unit to ensure proper operating condition 15 Installation Install in accordance with the manufacturer s instructions and in accordance with applicable local codes 16 Attachments changes or modifications Only use attachments accessories specified by the manufacturer Any change or modification of the equipment not expressly approved by Bosch could void the warranty or in the case of an authorization agreement authority to operate the equipment Important Notices Accessories Do not place this unit on an unstable stand tripod bracket or mount The unit may fall causing serious injury and or serious damage to the unit Use only with the cart stand tripod bracket or table specified by the manufacturer When a cart is used use caution and care when moving the car
162. ration with CCTV systems or local networks can be achieved quickly and easily Video images from a single camera can be simultaneously received on several receivers LIVE page Once the connection is established the Web browser displays the LIVE page It shows the live video image on the right of the browser window Depending on the configuration various text overlays may be visible on the live video image Other information may be shown next to live video image on the LIVE page The display depends on the settings selected in the LIVE Functions page see the AUTODOME 7000 Series online help Display Stamping Various overlays or stamps in the video image provide important status information The overlays provide the following information BA Decoding error The frame might show artifacts due to decoding errors If subsequent frames reference this corrupted frame they might also show decoding errors as well but won t be marked with the decoding error icon f Alarm flag set on media item ay Communication error Any kind of communication error is visualized by this icon Cause can be a connection failure to the storage medium a protocol violation with a sub component or simply a timeout An automatic reconnection procedure is started in the background in order to recover from this error Gap no video recorded Watermarking not valid Watermarking flag set on media item Motion flag set on media item Discovery of st
163. rd is normally dependent on the number of read write activities Bosch provides this guidance as a service to our customers with no representation of warranty either expressed or implied associated with the use of SD cards for recording Bosch is not liable for any damage that results from missing video information Bosch does not make any commitments or promises regarding quality performance or other features with respect to third party products such as SD cards Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 144 en Troubleshooting 16 AUTODOME 7000 Troubleshooting If you experience difficulties operating your AUTODOME camera refer to the following If the guidelines do not enable you to solve the problem contact an authorized technician Problem Questions to Ask Actions to Resolve the Problem Need to remove trim ring Use a slotted screw driver and push the clips outward while gently pulling down on the edge of the trim ring Nothing appears on the screen Are the power cord and line connection between the camera and monitor made properly The image on the screen is dim The contrast on the screen is too weak Is the lens dirty If so clean the lens with a soft clean cloth Adjust the contrast feature of the monitor Is the camera exposed to strong light If so change the camera position The image on the screen is flickers Does the camera fac
164. re indicated by a check mark 2 Check whether the required functions are available on the LIVE page Transmit audio You can only select this option if audio transmission is actually switched on see Audio page 106 The audio signals are sent in a separate data stream parallel to the video data and so increase the network load The audio data are encoded according to G 711 and require an additional bandwidth of approx 80 kbps per connection in each direction Lease time s The lease time in seconds determines the time beyond which a different user is authorized to control the camera after no further control signals are received from the current user After this time interval the camera is automatically enabled Show alarm inputs The alarm inputs are displayed next to the video image as icons along with their assigned names If an alarm is active the corresponding icon changes color Show alarm outputs Alarm outputs are shown next to the video image as icons along with their assigned names If the alarm output is active the corresponding icon changes color Show event log The event messages are displayed along with the date and time in a field next to the video image Show system log The system messages are displayed along with the date and time in a field next to the video image and provide information about establishing and ending connections for example Allow snapshots Here you can specify whether the icon for saving
165. rights 802 1x authentication the camera must be configured accordingly otherwise no communication is possible Image Selection You can view the image of the camera in different displays gt Click one of the tabs Stream 1 Stream 2 or M JPEG below the video image to toggle between the different displays of the camera image View Control The View Control tab allows you to control camera functions pan tilt zoom focus and iris navigate through on screen menus and to view preset scenes shots 1 Ref Description Ref Description 1 Tilts the camera up 8 Focus far 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Operation en 133 2 Tilts the camera down 9 Focus near 3 Pans the camera to the left 10 Iris close 4 Pans the camera to the right 11 Iris open 5 Pans and tilts the camera in all 12 Sets the pre set scene for the directions corresponding button 1 2 3 4 5 and 6 6 Zoom out 13 Moves the camera to pre set scene numbers 1 2 3 4 5 and 6 7 Zoom int 1 This function is also accessible by using the mouse scroll wheel while in the Live video frame 2 This button is also used as the Enter button to select menu items from the AUX tab To control a peripheral follow these steps 1 Click the appropriate controls 2 Move the mouse cursor over the video image Additional
166. rypted select the Off option to deactivate the port Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 124 en Configuration via IP Advanced Mode AUTODOME 7000 Telnet support If you want to allow only secure connections with encrypted data transmission you must select the Off option to deactivate Telnet support The unit will then no longer be accessible using the Telnet protocol Interface mode ETH If necessary select the Ethernet link type for the ETH interface Depending on the unit connected it may be necessary to select a special operation type Network MSS Byte You can set the maximum segment size for the IP packet s user data This gives you the option to adjust the size of the data packets to the network environment and to optimize data transmission Please comply with the MTU value of 1 514 bytes in UDP mode iSCSI MSS Byte You can specify a higher MSS value for a connection to the iSCSI system than for the other data traffic via the network The potential value depends on the network structure A higher value is only useful if the iSCSI system is located in the same subnet as the camera Network MTU Byte The value in the field defaults to 1514 14 43 DynDNS Enable DynDNS DynDNS org is a DNS hosting service that stores IP addresses in a database ready for use It allows you to select the camera via the Internet using a host name without having to know the current IP address of t
167. s If O K then If you are behind a firewall ensure that the Video Transmission mode is set to UDP Access the Settings Web page for the IP enabled device Expand the Service Settings link then click Network Select UDP from the Video Transmission drop down list Then click Set Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 146 en Maintenance AUTODOME 7000 17 Maintenance The bubble is made of Acrylic or Polycarbonate depending on the application Polycarbonate bubbles provide high impact resistance and its optical clarity is comparable to glass or acrylic although its surface is much softer All bubbles require special care when handling and cleaning to avoid scratches Notice To avoid excessive moisture saturation inside the housing limit the amount of time that the bubble is disconnected from the housing Bosch recommends that the bubble be removed from the housing for no more than five 5 minutes Bubble Handling The bubble may be packaged with a protective plastic sheet It is recommended that the bubble remain stored this way until it is ready to install Limit handling the bubble as any scratches can quickly affect visibility Bubble Cleaning If cleaning the bubble is required use the following procedures and comply with all the warnings listed below Cleaning the Bubble Interior The extremely soft interior surface should not be cleaned by rubbing
168. s inputs 3 through 7 You can configure alarms 3 through 7 as non supervised Normally Open N O or Normally Closed N C alarms Configuring a Normally Open Non supervised Alarm 1 Connect the alarm to the appropriate input 3 through 7 and ground at the camera Figure 12 4 N O Normally Open Non supervised Connections 1 Dry Contact 3 Dome Connector 2 Alarm Inputs 3 to 7 4 Ground 2 From the Settings menu select Advanced Mode gt Interfaces gt Alarm Inputs select the Alarm Input and N O See the table below for contact and condition details AutoDome Programmed N O Circuit Alarm Indication Open Normal Closed Alarm Configuring a Normally Closed Non supervised Alarm 1 Connect the alarm to the appropriate input 3 through 7 and ground at the camera Figure 12 5 N C Normally Closed Non supervised Connections 1 Dry Contact 3 Dome Connector 2 Alarm Inputs 3 to 7 4 Ground 2 From the Settings menu select Advanced Mode gt Interfaces gt Alarm Inputs select the Alarm Input and N C See the table below for contact and condition details AutoDome Programmed N C Circuit Alarm Indication Open Alarm Closed Normal 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Connection en 77 Alarm Outputs The camera incorporates two 2 types of alarm outputs one dry contac
169. s takes approximately 10 20 seconds During this time no changes can be made The cameo image freezes This section also displays a graphic that shows the relative image size difference between an image encoded at 1280 x 720 and at 1920 x 1080 Orientation Reverses the image 180 ideal when mounting upside down Set the orientation to Normal default or Inverted 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Configuration via IP Advanced Mode en 95 Caution The camera disables the Privacy Mask function if the orientation is set to Inverted SC settings Click the Default button to restore all camera settings to their original defaults SC data Click the Default button to clear all prepositions privacy masks and other configuration settings defined in the camera s web server to their default values Reboot device Click the Reboot button to reboot the camera There is a ten 10 second pause before the dome starts its homing phase During the homing phase the camera pans left and right and tilts up and down It also adjusts the lens focus The entire homing phase lasts approximately 40 seconds Factory defaults Click the Defaults button to restore the configuration settings defined in the camera s web server to their default values A confirmation screen appears Allow 5 seconds for the camera to optimize the picture after a mode reset Bosch Security Sys
170. s to connector P107 Caution To protect the camera from damage due to cold temperatures ensure that you connect the 24 VAC heater power wires to the P101 connector Connecting Alarm Inputs and Outputs gt To connect alarm inputs and outputs attach the supplied 6 pin Alarms In and the 4 pin Alarms Out connector plugs with flying lead wires to the appropriate incoming alarm wires Alarm Out 4 is a relay PIN PIN ORANGE sOn ARAON OoRKRWNE 1 4 pin Alarm 2 6 pin Alarm In 3 7 pin Relay Connector P104 Connector P102 Connector P103 Pin Description Pin Description Pin Description 1 Alarm Out 1 1 Alarm in 3 1 Alarm Out 4 Normally Open 2 Alarm Out 2 2 Alarm in 4 2 Alarm Out 4 COM 3 Alarm Out 3 3 Alarm in 5 3 Alarm Out 4 Normally Closed 4 Alarm Ground 4 Alarm in 6 4 Earth Ground 5 Alarm in 7 5 Analog Alarm 1 6 Alarm Ground 6 Analog Alarm 2 Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 56 en Installing the Roof Parapet and Pipe Mounts AUTODOME 7000 7 Ground For in ceiling mount only Low Voltage TTL 3 3V can also be used gt Connect the plugs to their mating connectors P103 and P102 on the Pipe Interface Board 1 To connect supervised alarms and relays attach the appropriate wires to their terminals on the P104 connector on the Pipe Interface Board see above 2
171. s to display the applicable storage media in the overview 2 Inthe Storage overview section double click the required storage medium an iSCSI LUN or one of the other available drives The medium is then added to the Managed storage media list In the Status column newly added media are indicated by the status Not active 3 Click the Set button to activate all media in the Managed storage media list In the Status column these are indicated by the status Online 4 Check the box in the Rec 1 or Rec 2 to specify which data stream should be recorded on the storage media selected Rec 1 stores Stream 1 Rec 2 stores Stream 2 This means that you can record the standard data stream on a hard drive and record alarm images on the mobile CF card for example 5 Check the boxes for the Overwrite older recordings option to specify which older recordings can be overwritten once the available memory capacity has been used Recording 1 corresponds to Stream 1 Recording 2 corresponds to Stream 2 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Configuration via IP Advanced Mode en 109 Caution If older recordings are not allowed to be overwritten when the available memory capacity has been used the recording in question will be stopped You can specify limitations for overwriting old recordings by configuring the retention time see Maximum Retention Time page 110 Formatting Storage Me
172. server using various time server protocols and then use it to set the internal clock The unit polls the time signal automatically once every minute gt Enter the IP address of a time server here Time server type Select the protocol that is supported by the selected time server Preferably you should select the SNTP server as the protocol This supports a high level of accuracy and is required for special applications and subsequent function extensions Select Time server for a time server that works with the protocol RFC 868 13 3 Basic Mode Network The settings on this page are used to integrate the camera into an existing network Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 86 en Configuration via IP Basic Mode AUTODOME 7000 Some changes only take effect after the unit is rebooted In this case the Set button changes to Set and Reboot 1 Make the desired changes 2 Click the Set and Reboot button The camera reboots and the changed settings are activated DHCP If a DHCP server is employed in the network for the dynamic assignment of IP addresses you can activate acceptance of IP addresses automatically assigned to the camera Certain applications VIDOS Bosch Video Management Systems Archive Player Configuration Manager use the IP address for the unique assignment of the unit If you use these applications the DHCP server must support the fixed assignment between IP address and
173. ss is inherent to digital video recording therefore Bosch Security Systems cannot be held liable for any damage that results from missing video information To minimize the risk of lost digital information Bosch Security Systems recommends multiple redundant recording systems and a procedure to back up all analog and digital information Notice This is a class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures FCC amp ICES Information U S A and Canadian Models Only This device complies with part 15 of the FCC Rules Operation is subject to the following conditions this device may not cause harmful interference and this device must accept any interference received including interference that may cause undesired operation NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules and ICES 003 of Industry Canada These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and radiates radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference
174. stalling the In Ceiling Mount Description This chapter details how to install the camera in an In Ceiling Mount The In Ceiling AUTODOME camera is suitable for use in environmental air spaces Refer to Installing the Pendant Arm Wall Corner and Mast Pole Mounts page 25 or refer to Installing the Roof Parapet and Pipe Mounts page 41 for these specific installations Dimensions Prepare Drywall Ceiling for Installation 1 Choose the desired location to mount the camera 2 Use the bracket Base Plate as a template to cut a 7 1 in hole with a tolerance of 1 8 in 180 34 mm 2 2 mm in the ceiling with a drywall utility saw or Jig Saw Proceed to Wire the Interface Box page 61 for further instructions Prepare Suspension Ceiling for Installation You must use the VGA IC SP In ceiling Support Kit to install the camera In ceiling housing into a suspended or drop ceiling This kit requires a separate purchase 1 Choose the desired location to mount the dome and remove an adjacent ceiling tile 2 Loosen the four 4 securing screws located in the corners of the Bracket Assembly enough to hold the suspension bars but still allowing adjustment during installation 3 Place the Bracket Assembly over the ceiling tile which is used to mount the camera Then snap the Bar Clips of the bracket to the ceiling rails Figure 10 1 Suspension Ceiling Bracket Top View 1 Suspension Bars 3 Securing Screw 4 2 Base Plate
175. sting The default is O no timeout Maximum image width Enter a number for the maximum width in pixels for the saved images 14 48 Accounts In order to configure image posting and to save and retrieve JPEG images you must create an Account in which to save and access them You can create a maximum of four 4 accounts Type Select the type of account FTP or Dropbox Account name Enter the name of the account IP address Enter the IP address of the server on which you wish to save the JPEG images Login Enter the login ID for the server Password Enter the password that gives you access to the server To verify the password click the Check button to the right Path Enter the exact path on which you wish to post the images on the server To browse for the correct path click the Browse button to the right Maximum bit rate Enter the maximum bit rate for the JPEG images in kbps 14 49 IPv4 Filter Use this setting to configure a filter that allows or blocks network traffic that matches a specified address or protocol IP Address 1 2 Enter the IPv4 address that you want to allow or block Mask 1 2 Enter the subnet mask for the appropriate IPv4 address 14 50 Encryption A special license with which you will receive a corresponding activation key is required to encrypt user data You can enter the activation key to release the function on the Licenses page see Licenses page 130 2014 04 2 0 F
176. storm or when leaving this unit unattended and unused for long periods unplug the unit from the wall outlet and disconnect the cable system This will prevent damage to the unit from lightning and power line surges Controls adjustment Adjust only those controls specified in the operating instructions Improper adjustment of other controls may cause damage to the unit Use of controls or adjustments or performance of procedures other than those specified may result in hazardous radiation exposure Overloading Do not overload outlets and extension cords This can cause fire or electrical shock Power cord and plug protection Protect the plug and power cord from foot traffic being pinched by items placed upon or against them at electrical outlets and its exit from the unit For units intended to operate with 230 VAC 50 Hz the input and output power cord must comply with the latest versions of IEC Publication 227 or IEC Publication 245 Power disconnect Units have power supplied to the unit whenever the power cord is inserted into the power source or when High Power over Ethernet High PoE power is provided over the Ethernet CAT 5E 6 cable The unit is operational only when the ON OFF switch is in the ON position The power cord is the main power disconnect device for switching off the voltage for all units When High PoE or PoE 820 3at is used to power the unit the power is provided over the Ethernet cable which is then the main powe
177. t apparatus combination to avoid injury from tip over Quick stops excessive force or uneven surfaces may cause the cart unit combination to overturn Mount the unit per the manufacturer s instructions All pole power switch Incorporate an all pole power switch with a contact separation of at least 3 mm in each pole into the electrical installation of the building f it is needed to open the housing for servicing and or other activities use this all pole switch as the main disconnect device for switching off the voltage to the unit Camera grounding For mounting the camera in potentially damp environments ensure to ground the system using the ground connection of the power supply connector see section Connecting external power supply Camera lens An assembled camera lens in the outdoor housing must comply and be tested in accordance with UL IEC60950 Any output or signal lines from the camera must be SELV or Limited Power Source For safety reasons the environmental specification of the camera lens assembly must be within the environmental specification of 10 C 14 F to 50 C 122 F Camera signal Protect the cable with a primary protector if the camera signal is beyond 140 feet in accordance with NEC800 CEC Section 60 Coax grounding Ground the cable system if connecting an outside cable system to the unit Connect outdoor equipment to the unit s inputs only after this unit has had its grounding plug
178. t for the remaining commands is scheduled for a future release Shot defines a preset scene from shot 1 256 4 Click Set to save and to activate the alarm rules Advanced Mode Interfaces v Interfaces Alarm Inputs Alarm Outputs Alarm Inputs Select the type of input for each physical alarm Select from either N O Normally Open or N C Normally Closed and provide an optional name for each input Alarm Outputs The camera incorporates three 3 open collector alarm or transistor outputs Use the following settings to configure the relay for alarm outputs Idle state Specify either Open or Closed idle state Operating mode Select one of the following modes for operation Bistable 0 5 s 1 s 5 s 10 s or 60s Output name Type an optional name for the relay connection up to 20 characters Trigger output Click the appropriate Trigger output button to test the relay output connection Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 122 en Configuration via IP Advanced Mode AUTODOME 7000 14 41 14 42 Advanced Mode Network v Network Network Access DynDNS Advanced Network Management Multicast Image Posting Accounts IPv4 Filter Network Access The settings on this page are used to integrate the camera into an existing network Some changes only take effect after the unit is rebooted In this case the Set button changes to Set and Reboot 1 M
179. t playback speed by means of the speed regulator slide control Bookmarks In addition set markers in the sequences so called bookmarks and jump directly to these These bookmarks are indicated as small yellow arrows above the time interval Use the bookmarks as follows E Jump to the previous bookmark Set bookmark a Jump to the following bookmark Bookmarks are only valid while in the Recordings page they are not saved with the sequences All bookmarks are deleted when leaving the page Tracking For information about the Tracking section of the LIVE page refer to Using Intelligent Tracking page 139 See also User Command Table page 149 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 15 2 Operation en 139 Using Intelligent Tracking Configuring Intelligent Tracking The camera utilizes the built in Intelligent Video Analytics IVA to continuously follow an individual or object even if it passes behind a Privacy Mask or a stationary object The camera uses objects detected by IVA in a stationary preset position to activate the Intelligent Tracking feature The Intelligent Tracking feature allows continuous on screen following of an individual or an object This feature operates by recognizing an object in motion and zooms in to approximately 50 default Tracker zoom threshold of the field of view for an average target height of six feet This feature controls
180. t relay and three 3 open collector outputs or transistor outputs Configuring a Dry Contact Relay The dry contact relay acts like an on off switch It has a maximum voltage rating of 2A 30 DC 1 Connect the appropriate stripped wire to the camera s COM connector 2 Connect the appropriate stripped wire to the N O or N C connector depending on your requirement Configuring an Open Collector Output Outputs 1 2 and 3 are open collector types These outputs must be connected to a positive voltage between 5 and 32 V to complete the circuit with a maximum voltage rating of 32 VDC 150 ma 1 Connect the appropriate stripped wire to the open connector 1 2 or 3 of the transistor 2 Connect the appropriate stripped wire to the ground GND connector 11 6 Audio Connections Optional The camera is capable of receiving line level input signals and transmitting them over a network It is also capable of receiving audio from the same network and sending it as audio output from the camera The audio input signal is transmitted in sync with the video signals As a result for example a door intercom system can be connected at the camera location Notice The line ports of the intercom should be used for transmitting audio signals on the intercom systems The audio line input is not suitable for direct microphone signal connection The audio line output is not suitable for direct speaker connection unless using a powered
181. t setting Stream 1 is transmitted for alarm connections and automatic connections Keep this fact in mind when assigning the profile Notice All parameters combine to make up a profile and are dependent on one another If you enter a setting that is outside the permitted range for a particular parameter the nearest permitted value will be substituted when the settings are saved Profile name If required enter a new name for the profile Target bit rate To optimize use of the bandwidth in the network limit the data rate for the device The target data rate should be set according to the desired picture quality for typical scenes with no excessive motion For complex images or frequent changes of image content due to frequent movements this limit can temporarily be exceeded up to the value entered in the Maximum bit rate field Maximum bit rate This maximum bit rate is not exceeded under any circumstances Depending on the video quality settings for the l and P frames this fact can result in individual images being skipped The value entered here must be at least 10 higher than the value entered in the Target bit rate field If the value entered here is too low it will be adjusted automatically Encoding interval This parameter determines the interval at which images are encoded and transmitted For example entering or selecting 4 means that only every fourth image is encoded while the following there are skipped which can
182. t the nearest Bosch Security Systems Service Center for authorization to return and shipping instructions Service Centers USA Telephone 800 366 2283 or 585 340 4162 Fax 800 366 1329 Email cctv repair us bosch com Customer Service Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 12 en Safety EN AUTODOME 7000 Telephone 888 289 0096 Fax 585 223 9180 Email security sales us bosch com Technical Support Telephone 800 326 1450 Fax 585 223 3508 or 717 735 6560 Email technical support us bosch com Repair Center Telephone 585 421 4220 Fax 585 223 9180 or 717 735 6561 Email security repair us bosch com Canada Telephone 514 738 2434 Fax 514 738 8480 Europe Middle East amp Africa Region Please contact your local distributor or Bosch sales office Use this link http www boschsecurity com startpage html europe htm Asia Pacific Region Please contact your local distributor or Bosch sales office Use this link http www boschsecurity com startpage html asia_pacific htm More Information For more information please contact the nearest Bosch Security Systems location or visit www boschsecurity com 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 2 1 Unpacking en 13 Unpacking This equipment should be unpacked and handled with care If an item appears to have been damaged in shipment notify the shipper immediatel
183. tems Inc Operation Manual 2014 04 2 0 F 01U 283 679 96 en Configuration via IP Advanced Mode AUTODOME 7000 14 12 Encoder Profile Encoder Profile ane ena ae aoe a HD Image Optimized Ea Expert Setting Default Figure 15 1 Advanced Mode gt Camera gt Encoder Profile gt Profile 1 HD models only For the video signal encoding you can select a code algorithm and you can change the presets for the profiles You can adapt the video data transmission to the operating environment for example network structure bandwidth data load To this end the camera simultaneously generates two data streams Dual Streaming which compression settings you can select individually for example one setting for transmissions to the Internet and one for LAN connections Pre programmed profiles are available each giving priority to different perspectives You can change individual parameter values of a profile and you can also change the name You can switch between profiles by clicking the appropriate tabs Caution The profiles are rather complex They include a large number of parameters that interact with one another so it is generally best to use the default profiles Change the profiles only once you are fully familiar with all the configuration options 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Configuration via IP Advanced Mode en 97 Notice In the defaul
184. th a diameter of 10 mm 3 8 inch All bolts must fully extend through the mounting surface and be secured with a flat washer lock washer and a nut All studs must be anchored to concrete or welded to a steel backing plate Anchor bolts can be used for blind structures where there is no access to the rear 3 Apply a weatherproof sealant around each fastener hole at the mounting surface 4 Attach the Parapet Wall Bracket using at least six 6 stainless steel fasteners three 3 on each side the bracket has eight 8 holes Be careful not to over tighten the fasteners because it may strip the threads If attaching the parapet mount to a flat roof attach the optional LTC 9230 01 Roof Mount Plate to the roof and then attach the Parapet Wall Bracket to the Roof Mount Plate 5 Insert the Parapet Pipe Arm into the mounting bracket until it bottoms in the bracket 6 Remove the End Cap from the front of the arm and feed the video control and power wires up through the bottom of the pipe arm and out the front end Figure 9 8 VGA ROOF MOUNT 1 End Cap with O ring 2 Parapet Pipe Arm 3 1 4 20 SS Cap Screw 4 Down Pipe 5 10 24 SS Pan Head Screw 7 Fold the video control and power wires back at the front end of the arm and route them down and out through the Down Pipe Then replace the End Cap 8 Wrap at least five layers of Teflon tape around the Down Pipe threads 9 Apply the supplied thread sealant to the D
185. the pan tilt zoom actions of the camera to keep the selected object in the scene To activate the Intelligent Tracking feature one of the following conditions must be met The Silent IVA option must be selected in the VCA page on the Settings tab Refer to VCA page 114 IVA must be active for at least one preset scene in the VCA page on the Settings tab If IVA is configured for one scene then all other scenes have Intelligent Tracking enabled by default If a scene has Motion of IVA Flow activated however then Intelligent Tracking is disabled for these scenes Notice The following actions occur if Intelligent Tracking is active All other IVA objects are disabled in scenes with Intelligent Tracking The camera automatically disables the display of compass headings Once Intelligent Tracking is set to Off the camera resumes display of the compass heading Refer to PTZ Settings page 104 for details of the Compass feature Guidelines for Implementing Intelligent Tracking Factors such as the viewing angle and unwanted motion from trees for example may interfere with Intelligent Tracking operation Use the following recommendations to ensure smooth Intelligent Tracking operation Mount Mounting Surface Stability Mount the camera in the most stable position Avoid locations affected by vibrations such as those caused by a roof top air conditioner These vibrations may cause complications when the camera zooms in on a
186. tle overlays for a few seconds OSD titles can be displayed at a position of your choice or it can be set to Off for no overlay information 1 Select the desired option from the list 2 Specify the exact position Position XY 3 Inthe Position XY fields enter the values for the desired position Camera OSD Select On to momentarily display camera response information such as Digital Zoom Iris open close and Focus near far overlays in the image Select Off to display no information 1 Select the desired option from the list 2 Specify the exact position Position XY 3 Inthe Position XY fields enter the values for the desired position Transparent stamping Check this box to make the stamp on the image transparent Video watermarking Choose On if you wish the transmitted video images to be watermarked After activation all images are marked with a green check A red check indicates that the sequence live or saved has been manipulated Video authentication Select a method for verifying the integrity of the video in the Video authentication drop down box If you select Watermarking all images are marked with an icon The icon indicates if the sequence live or saved has been manipulated If you want to add a digital signature to the transmitted video images to ensure their integrity select one of the cryptographic algorithms for this signature Bosch Security Systems Inc Operation Manual 2014 04
187. to power the camera and the heaters For in ceiling or indoor pendant applications that don t require heater power standard PoE 802 3at midspans or switches can be used to power the camera When powering the camera via PoE or a midspan device additional surge protection is required If auxiliary power 24VAC camera and 24VAC heater and High PoE are applied simultaneously the camera selects the auxiliary 24VAC input and draws minimal power from the High PoE midspan 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Connection en 73 Caution Ethernet CAT 5E CAT 6 cables must be routed through earth grounded conduit for indoor or outdoor applications For outdoor applications the conduit should be capable of withstanding the outdoor environment Notice The heater in an outdoor AUTODOME unit cannot be powered via the Power over Ethernet IEEE 802 3at class 4 standard unless the heater is connected to a High PoE Midspan 60W Single port sold separately See the Installation Manual of the Midspan for details Cable Type CAT 5E or CAT 6 Ethernet Maximum Distance 100 m 328 ft where heater is not Bandwidth 10 Base T 100 Base TX High PoE required for pendants in outdoor applications that use Use the Bosch High PoE 60W midspan heaters sold separately PoE only for indoor models or indoor applications for pendant model IEEE 802 3at
188. tore Camera Restores all setting to their original Settings defaults Y Y On Off 43 Auto Gain Control AGC On Auto Off 50 Playback Tour A Activate Deactivate 52 Playback Tour B Activate Deactivate Y On Off 57 Night Mode setting Enables Disables Night Mode Day Night only Y Y On Off 60 On Screen Display On enable Off disable Y Y On Off 66 Display Software Display software version information Version Issue Once presents basic information Issue Twice while basic info displayed presents expanded information HD models only On Off 78 Intelligent Tracking Turns Intelligent Tracking on or off Y Y On Off 80 Digital Zoom Lock Turns digital zoom on and off Y Y On Off 86 Sector Blanking On enable Off disable Y Y On Off 87 Privacy Masking On enable Off disable Y On Off 90 Command Lock Unlock On lock on Off lock off Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 150 en User Command Table AUTODOME 7000 Locked Alarm Rule Function Comm Command Description Output Key No Y On Off 94 Set Azimuth Zero Point Sets the zero degree pan position On Off 95 Display Azimuth On Displays azimuth elevation Elevation Readings readings Off Hides azimuth elevation readings On Off 96 Display Compass On Displays compass heading Heading Off Hides compass heading On Off 100 Record Tour A On start recording Off stop recording On Off 101 Record Tour B On start recording Of
189. trol window 3 Click Enabled to enable the virtual mask The rectangle that represents the mask in the preview window becomes red The text Virtual Masks ENABLED appears in the View Control window To disable virtual masks Click the Disable masks checkbox The text Virtual Masks DISABLED appears in the View Control window 14 34 Audio Alarm The camera can create alarms on the basis of audio signals You can configure signal strengths and frequency ranges in such a way that false alarms for example due to machine noise or background noise are avoided 2014 04 2 0 F 01U 283 679 Operation Manual Bosch Security Systems Inc AUTODOME 7000 Configuration via IP Advanced Mode en 119 Notice First set up normal audio transmission before you configure the audio alarm here see Audio page 106 Audio alarm Select On if you want the device to generate audio alarms Name The name makes it easier to identify the alarm in extensive video monitoring systems for example with the VIDOS and Bosch Video Management System programs Enter a unique and clear name here 14 35 Caution Do not use any special characters for example amp in the name Special characters are not supported by the system s internal recording management and may therefore result in the Player or Archive Player programs being unable to play back the recording Signal Ranges You can exclude particular signal ranges in order to av
190. ultiple units in larger video monitoring systems easier for example using the Bosch Video Management Systems programs The device name is used for the remote identification of a unit in the event of an alarm for example For this reason enter a name that makes it as easy as possible to quickly identify the location Caution Do not use any special characters for example amp in the name Special characters are not supported by the system s internal recording management and may therefore result in the Player or Archive Player being unable to play back the recording Confirm password In each case enter the new password a second time to eliminate typing mistakes Notice A new password is only saved when you click the Set button You should therefore click the Set button immediately after entering and confirming a password 13 2 Basic Mode Date Time Device date Device time Device time zone If there are multiple devices operating in your system or network it is important to synchronize their internal clocks For example it is only possible to identify and correctly evaluate simultaneous recordings when all units are operating on the same time If necessary you can synchronize the unit with your computer s system settings Notice Ensure that recording is stopped before synching to the PC gt Click the Sync to PC button to copy your computer s system time to the camera Time server IP address The camera can receive the time signal from a time
191. vent must be set The following standard tasks can be set Object in field Crossing Line Loitering Condition change Following route Entering field and Leaving field Refer to the IVA 5 60 Operation Manual for specific information A user manually selects an object in the live image area to track The Intelligent Tracking feature allows a user to click a moving object in the live image display inside the LIVE page to identify an object to track Use AUX Command 78 to activate deactivate Intelligent Tracking Use AUX ON 78 to enable the Intelligent Tracking Auto mode This command can be used in conjunction with the rules engine Using Intelligent Tracking Use the following options on the LIVE page to control Intelligent Tracking Note If you do not see these controls on the LIVE page ensure that the Show Tracking option is enabled on the LIVE Functions page Refer to LIVE Functions page 93 Tracking 9 off Auto click Off Disables Intelligent Tracking Auto In this mode the camera actively analyzes the video to detect any moving object If it detects movement the camera begins to track the moving object This mode is most useful for scenarios where no motion is expected in the scene Click In this mode users can click an object moving in the live video image to enable the camera to track the movement of the selected object This mode is most useful for scenarios where normal scene activity is expected
192. vent will be executed Off default camera remains on a current scene indefinitely Scene 1 camera returns to Preset 1 Previous Aux camera returns to the previous activity Inactivity period Determines the behavior of the dome when the control for dome is inactive Select a time period from the pull down list 3 sec 10 min The default setting is 2 minutes Auto pivot The Auto pivot tilts the camera through the vertical position as the camera is rotated to maintain the correct orientation of the image Set the Auto Pivot to On default to automatically rotate the camera 180 when following a subject traveling directly beneath the camera To disable this feature click Off Freeze frame Select On to freeze the image while the camera moves to a predetermined scene position Turbo mode Select On to set the camera in Turbo mode when an operator pans or tilts the camera manually In this mode the camera can pan at a maximum of 400 per second and tilt at a maximum of 300 per second Tracker Zoom Threshold This parameter defines the zoom ratio percentage to which the camera zooms out after Tracker Timeout stops tracking or if Intelligent Tracking loses visibility of an object being tracked This allows the camera to re acquire the target in a new wider FoV Settings range from O to 100 The default is 50 Tracker Timeout sec This parameter allows the camera to stop tracking motion of certain objects such as
193. y Verify that all the parts listed in the Parts List below are included If any items are missing notify your Bosch Security Systems Sales or Customer Service Representative Refer to Customer Support and Service for contact information The original packing carton is the safest container in which to transport the unit and must be used if returning the unit for service Save it for possible future use Parts List Installation The following table lists the parts included in the shipping box for In ceiling models of AUTODOME 7000 In ceiling Mount Quantity Item 1 AUTODOME 7000 In Ceiling camera with acrylic bubble and white trim ring 1 Interface box 1 Optional black trim ring 1 Ceiling gasket for IP54 conformance 1 Product DVD which includes complete Operation Manual 1 Packet of printed Safety literature To mount an In ceiling mount model of AUTODOME 7000 you must purchase a Bracket Assembly Support Kit part number VGA IC SP This Kit is sold separately from the camera The following table lists the parts included in the shipping box for pendant models of AUTODOME 7000 Pendant Mount Quantity Item 1 AUTODOME 7000 Pendant camera with clear acrylic bubble and sunshield 1 Product DVD which includes complete Operation Manual 1 Packet of printed Safety literature The following table lists the optional parts sold separately that you may need for attaching a
194. your cursor over the live image and wait for the area to display a directional arrow Click and hold a mouse button to pan to the desired position that you want to save Click any number combination from 1 256 from the on screen keypad to identify the scene number Click the Set scene button The image area displays a message that indicates which shot number was saved To View a Preset Shot 1 Click the number of the scene you want to view using the on screen keypad Bosch Security Systems Inc Operation Manual 2014 04 2 0 F 01U 283 679 136 en Operation AUTODOME 7000 2 Click the Show scene button Notice For more information about the camera settings and controls click the Help on this page link to open the online help LIVE page Special Functions The camera offers special command buttons on the LIVE page Special Functions Scan 360 Click this button to start a continuous 360 pan To stop the continuous pan click a directional control in the View Control tab Autopan Click this button to pan the camera between user defined limits To set the left and right pan limits refer to PTZ Settings in the Operator Manual To stop the continuous pan click a directional control in the View Control tab Tour A Tour B Click one of these buttons to start the playback of a recorded guard tour A Recorded Tour saves all manual camera movements made during the recording including its rate of p
195. ype are displayed To play back recorded video sequences 1 Select Recording 1 or 2 in the drop down menu The contents for 1 and 2 are identical only the quality and location may be different 2 Use the arrow buttons to browse the list 3 Click a track The playback for the selected sequence starts Export to FTP Click Export to FTP to send the current track to the FTP server If required change the times within the selected range Controlling Playback A time bar below the video image allows quick orientation The time interval associated with the sequence is displayed in the bar in gray A green arrow above the bar indicates the position of the image currently being played back within the sequence 01 01 2000 CAIRE TENE The time bar offers various options for navigation in and between sequences Change the time interval displayed by clicking the plus or minus icons The display can span a range from two months to a few seconds If required drag the green arrow to the point in time at which the playback should begin Red bars indicate the points in time where alarms were triggered Drag the green arrow to navigate to these points quickly Control playback by means of the buttons below the video image The buttons have the following functions B Start Pause playback Eg Jump to start of active sequence or to previous sequence ey Jump to start of the next video sequence in the list Continuously selec

Autodome 7000 Series Operation Manual

Contents

Download Pdf Manuals

Related Search

Related Contents