MARCY PLATINUM MP-3500 HOME GYM
Contents
1. H Slide a 7 Swivel Tube Sleeve 438 onto the tube on the Lever Frame Handle 434 I Push one Y 4 Large Foam Roll 58 onto Sleeve Plug one Foam Roll End Cap 459 into the end of Handle J Slide one Foam Tube 23 halfway through the hole on the Leg Machine Frame 31 Secure it with one M6x 3 8 Screw 4108 Push the 6 7 8 Grips 67 onto the Tube 12 DIAGRAM 4 STEP 5 See Diagram 5 A Slide the Right Butterfly 10 onto the right axle on the Butterfly Base 13 B Insert the Butterfly Handle 49 into the pivot on the Right Butterfly Secure it with one M10 x 34 Allen Bolt 103 and Y 1 14 Washer 70 from the bottom C Repeat Procedures A and B above to install the other side Do not over tighten the Bolts Make sure the Handles are able to swivel DIAGRAM 5 STEP 6 See Diagram 6 amp Upper Cable Loop Diagram A B x C Attach the 167 Upper Cable 42 to the opening on the front of Upper Frame 1 Make sure the ball stopper is underneath the Frame Attach a Pulley 444 to the Cable Secure the Pulley to the opening with one M10 x 3 3 8 Allen Bolt 97 two Pulley Bushings 53 and one M10 Aircraft Nut 109 Draw the Cable over the Pulley along the Upper Frame towards the back of the machine to the opening in the middle of Upper Frame Repeat Procedure B above to install a Pulley Draw the Cable around the Pulley then back to the upper opening on2. WEIGHT PLATE Station 1 2 4 5 6 7 8 9 Low Pulley 9 13 5 18 225 27 31 5 36 40 5 45 Lat Pull 13 5 18 225 27 31 5 36 40 5 45 49 5 Butterfly 4 5 6 75 9 11 25 13 5 15 75 18 20 25 12 5 Front Press 9 15 75 22 5 29 25 36 42 75 49 5 56 25 63 AB Crunch 9 13 5 18 22 5 27 81 5 36 40 5 45 en 9 135 18 225 27 81 5 36 40 5 45 Hip Thigh 4 5 9 13 5 18 225 27 31 5 36 40 5 WEIGHT PLATE Station 10 1 31 1 12 13 14 Low Pulley 49 5 54 58 5 63 67 5 Lat Pull 54 58 5 63 67 5 72 Butterfly 24 75 27 29 25 31 5 33 75 Front Press 69 75 76 5 83 25 90 96 75 AB Crunch 49 5 54 58 5 63 67 5 Leg Developer 49 5 54 58 5 63 67 5 Hip Thigh 45 495 54 585 63 Numbers are approximate Actual weight may vary Value for butterfly is for each arm All values are in KGS 28 PARTS LIST KEY NO DESCRIPTION Upper Frame Front Press Base Front Press Vertical Frame Backrest Support Frame Seat Post Seat Support Frame Leg Developer Butterfly Handle Right Butterfly Left Butterfly Front Base Frame Butterfly Base Foot Plate Rear Base Frame Rear Stabilizer Guide Rod Single Floating Pulley Bracket Leg Developer Axle Double Floating Pulley Bracket Butterfly Base Cover Shiver Bar Foam Tube Lat Bar 4 34 x 2 34 Bracket 5 2 x 2 Bracket Angled Double Floating Pulley Bracket Selector Rod 6 34 Front
3. 8 Carriage Bolts 106 from the bottom two M10 x 3 5 8 Carriage Bolts 105 from the side of Butterfly Base four Y 34 Washers 111 and four M10 Aircraft Nuts 109 Connect the Rear Base Frame 15 to the Rear Stabilizer 16 Secure them together with two M10 x 3 5 8 Allen Bolts 96 two 34 Washers 111 and one 2 x 1 gt Bracket 36 Attach the Foot Plate 14 to the Front Base Frame 12 Align the holes and insert the Foot Plate Axle 37 through the holes Slide 14 Weight Plates 80 onto the Guide Rods Make sure the deep groves on all Plates face down and toward the back Insert the Selector Rod 17 through the center hole on the Weight Plates Slide the Weight Selector Stem 81 onto the Guide Rods Use the Weight Plate Selector Pin 274 to select desired number of Weight Plates to exercise NOTE Each Plate weights approximately 4 5kgs Please refer to the Weight Resistance Chart on page 28 DIAGRAM 1 e Ue Q ef gt II MP TIS es STEP 2 See Diagram 2 A Attach the Upper Frame 1 onto the two Guide Rods 17 Secure it with two M10 x 34 Allen Bolts 103 and 2 34 Washers 111 DO NOT tighten the Bolts yet B Place the Upper Frame onto the Vertical Frame 44 Secure it with two M10 x 2 5 8 Carriage Bolts 106 one 4 37 x 2 4 Bracket 25 two Y 34 Washers 111 and two M10 Aircraft Nuts 109 C Securely tighten all Nuts and Bolts previously insta
4. Press Base Axle 7 V2 Front Press Axle Leg Machine Frame Rotating Cam Plate Lever Frame Lever Frame Handle Bar Handle Frame 2 34 x 1 Ye Bracket Foot Plate Axle 7 Swivel Tube Sleeve 75 Hip Thigh Cable 215 Lower Cable 83 Butterfly Cable 167 Upper Cable Bar Handle Frame Bushing Pulley Small Pulley Weight Stack Cover Ball Stopper U shaped Cable Connector Y 1 12 Rubber Bumper Y 1 Bushing Y 1 12 Butterfly Bushing Y 2 3 8 x 1 Rubber Bumper Pulley Bushing 1 x 3 8 Bushing 1 14 Front Press Bushing 7 8 Leg Developer Bushing Butterfly Handle Grip 4 Large Foam Roll Foam Roll End Cap 1 4 x Y2 Bushing Oo lt 0 NM 2m mm mm mm MI Add I Dh mm mm NN mm mm LA BR GO D ND ND D oo D ND D D 29 5 3 8 Grip Y 1 End Cap 2 x 2 End Cap 1 x 2 End Cap 1 x 2 End Cap 2 x 2 End Cap 6 7 8 Grip Manual D 1 x 1 5 8 Rubber Bumper 1 Va Washer Y 1 Rubber Bumper 6 Grip 3 3 8 T shaped Lock Pin Weight Plate Selector Pin Short Chain Long Chain 6 T shaped Lock Pin 4 T shaped Lock Pin Y 2 End Cap Weight Plate Selector Stem 1 Con shaped End Cap Single Handle Ankle Strap Abdominal Strap Foam Roll Medium Pulley Seat Pad Backrest Board Hook 5 Allen Wrench Tool Foam Roll Vinyl Cover Foot Support Panel M10 x 6 12 Allen Bolt M10 x 4 14 Allen Bolt M10 x 3
5. on the Leg Developer 8 Attach a Pulley 44 to the opening Secure it with one M10 x 2 Y Allen Bolt 98 two Y 7 8 Leg Developer Pulley Bushings 56 and one M10 Aircraft Nut 4109 Draw the Cable underneath the Pulley to the open bracket on the Front Base Frame 12 Attach a Pulley to the bracket Secure it with one M10 x 1 9 Allen Bolt 99 two Y 34 Washers 111 and one M10 Aircraft Nut 109 Draw the Cable underneath the Pulley towards the back of the machine through the bottom opening on the Vertical Frame 4 to the open bracket on the Rear Base Frame 415 Repeat Procedure B above to install a Pulley Draw the Cable underneath the Pulley then pull upward to the Double Floating Pulley Bracket 20 previously installed in STEP 6 Repeat Procedure B above to install a Pulley After completing the entire cable system come back to the Double Floating Pulley Bracket and adjust the height of the lower Pulley to adjust the tightness of the Cables Move up the pulley to increase the tension Move down the pulley to loose the tension Draw the Cable around the Pulley then downward Attach the Cable to a Single Floating Pulley Bracket 18 Repeat Procedure B to install a Pulley Draw the Cable around the Pulley then upward to the open bracket on the back of Vertical Frame 4 Repeat Procedure B to install a Pulley Draw the Cable around the Pulley then downward Attach the Cable to an Angled Double Floating Pulley Brac
6. 5 8 Allen Bolt M10 x 3 3 8 Allen Bolt M10 x 2 12 Allen Bolt M10 x 1 9 Allen Bolt M10 x 1 1 8 Allen Bolt Double Large Pulley Bracket M10 x 1 Allen Bolt M10 x 37 Allen Bolt 6 Allen Wrench Tool M10 x 3 5 8 Carriage Bolt M10 x 2 5 8 Carriage Bolt M6 x 5 8 Screw M6 x 3 8 Screw M10 Aircraft Nut M12 Aircraft Nut 34 Washer 5 8 Washer M8 x 1 5 8 Allen Bolt gt o o c PPRrN B DOD D 2 0R DD WD U DD DD HH BDO DD PRODUOD 00 LIMITED WARRANTY Escalade warrants this product to be free from defects in workmanship and material under normal use and service conditions for a period of two years on the frame and one year on all other parts and components from the date of purchase This warranty extends only to the original purchaser Escalade s obligation under this Warranty is limited to replacing damaged or faulty parts at Escalade s option All returns must be pre authorized by Escalade This warranty does not extend to any product or damage to a product caused by or attributable to freight damage abuse misuse improper or abnormal usage purchasers own repairs or for products used for commercial or rental purposes No other warranty beyond that specifically set forth above is authorized by Escalade Escalade is not responsible or liable for indirect special or consequential damages arising out of or in connection with the use or performance of the product or o
7. Meas read ll isc a E PAR CY product N 0 7 MARCY PLATINUM Safety Notice MP 3500 HOME GYM Hardware Identifier Assembly Instruction Parts List Warranty Ordering Parts Model MP 3500 Retain This Manual for Reference 08 25 09 OWNER S MANUAL Escalade International Limited Pleasant Road Penllergaer Swansea SA4 9GE Tel 00 44 1792 222550 Fax 00 44 1792 895781 escaladesports co info escaladesports co uk TABLE OF CONTENTS BEFORE YOU BEGIN oaia anal int ua bai i ea d e ba ia 1 IMPORTANT SAFETY NOTES nn aaa 2 HARDWARE PACK fee 4 ASSEMBLY INST RUG TIONS iiir eR Exe Dx ara BR RE le 7 WEIGHT RESISTANCE CHART ii 28 PARIS LIS eT 29 WARRAN errante a 30 ORDERING PARTS ir i tt aa 30 BEFORE YOU BEGIN Thank you for selecting the MARCY PLATINUM Home Gym MP 3500 For your safety and benefit read this manual carefully before using the machine As the distributor we are committed to provide you complete customer satisfaction If you have any questions or find there are missing or damaged parts or you require assistance assembling this product we guarantee you complete satisfaction through direct assistance To avoid unnecessary delays please call our customer service department Monday to Friday 9am to 5pm Tel Fax 0044 0 1792 222562 E mail customerservices escaladesports co uk Supplie
8. RE PACK 74 Weight Plate Selector Pin Qty 1 EI 75 Short Chain Qty 1 90 Hook Qty 5 77 6 4 T shaped Lock Pin Qty 1 78 4 T shaped Lock Pin Qty 1 mm mm 19 Leg Developer Axle Qty 1 73 3 T shaped Lock Pin Qty 1 76 Long Chain Qty 1 6 ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine Two Adjustable Wrenches and Allen Wrenches NOTE It is strongly recommended that two or more people assemble this machine to avoid possible injury STEP 1 See Diagram 1 A UD O m TI I Insert two Guide Rods 17 into the holes on Rear Stabilizer 16 Secure each Guide Rod with one M10 x 37 Allen Bolt 103 and 34 Washer 111 from the bottom Slide two 2 3 8 x 1 Rubber Bumpers 52 onto the two Guide Rods Do not tighten the Nuts and Bolts starting from the following procedures until instructed to do so Attach the Vertical Frame 4 onto the Rear Base Frame 15 Secure it with two M10 x 2 5 8 Carriage Bolts 106 one 4 34 x 2 34 Bracket 25 two 32 Washers 111 and two M10 Aircraft Nuts 109 Attach the Butterfly Base 13 to the Rear Base Frame 15 Attach the Front Base Frame 12 to the Butterfly Base 13 Make sure the L shaped bracket welded on the Butterfly Base 13 face towards the front of the machine see small diagram in the square insert in Diagram 1 Align the holes and secure them together with two M10 x 2 5
9. T wear robes or other clothing that could become caught in the Gym Running or aerobic shoes are also required when using the Gym Use the Gym only for its intended use as described in this manual DO NOT use attachments not recommended by the manufacturer Do not place any sharp objects around the Gym 10 Disabled persons should not use the machine without a qualified person or physician in attendance 11 Before using the Gym to exercise always do stretching exercises to properly warm up 12 Never use the Gym if it is not functioning properly 13 This product is intended for H Domestic Home use only CARE AND MAINTENANCE 1 Inspect and tighten all parts before using the machine 2 The machine can be cleaned using a damp cloth and mild non abrasive detergent DO NOT 3 use solvents Periodically spray the Guide Rods 17 with silicon spray or light oil to ensure a smooth operation 4 Failure to examine the Gym regularly may affect the safety level of the equipment 5 6 Assembled Dimensions L 190 x W 127 x H 209 cm Maximum user weight is 140kg WARNING BEFORE BEGINNING ANY EXERCISE PROGRAM CONSULT YOUR PHYSICIAN THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE EXISTING HEALTH PROBLEMS READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT ESCALADE ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT SAVE THESE INSTRUC
10. TIONS WARNING LABEL PLACEMENT an SS IS SS Do not attempt t ercise or han from the lat bar while it is placed or stored on the o ex sto e EI F PARE AP iC en O HARDWARE PACK NOTE The following parts are not drawn to scale Please use your own ruler to measure the size MM 94 M10 x 6 3 Allen Bolt Qty 2 L m 95 M10 x 4 1 Allen Bolt Qty 1 ms 96 M10 x 3 Allen Bolt Qty 4 L m 97 M10 x 3 3 Allen Bolt Qty 9 Em 105 M10 x 3 3 Carriage Bolt Qty 2 106 M10 x 2 Carriage Bolt Qty 8 imm 98 M10 x 2 Allen Bolt Qty 1 mm 99 M10 x 1 3 Allen Bolt Qty 16 um 100 M10 x 1 Allen Bolt Qty 1 inm 102 M10 x 1 Allen Bolt Qty 2 pmm 103 M10 x 3 Allen Bolt Qty 16 0 1 2 3 4 5 6 7 8 9 10 1 12 13 14 15 16 17 18 19 20 HARDWARE PACK NOTE The following parts are not drawn to scale Please use your own ruler to measure the size CO 30 7 3 Front Press Axle Qty 1 JI 29 6 3 Front Press Base Axle Qty 1 TT II 110 M12 Aircraft Nut Qty 1 108 M6 x Screw Qty 1 i 53 Pulley Bushing Qty 14 56 Leg Developer Bushing Qty 2 imi 70 1 4 Washer Qty 8 109 M10 Aircraft Nut Qty 49 112 Y Washer Qty 4 111 2 j Washer Qty 78 o 1 8 3 4 5 6 7 B 9 10 11 1 13 14 15 16 17 18 19 Qty 74 e m 5 al o N e HARDWA
11. ad the 6 14 T shaped Lock Pin 77 into the hole on the side of the Vertical Frame to obtain the desired Backrest position 10 DIAGRAM 3 STEP 4 See Diagram 4 A Attach the Seat Pad 88 to the Seat Post 6 Secure it with two M8 x 1 5 8 Allen Bolts 113 and 5 8 Washers 112 B Insert the Seat Post into the opening on the Seat Support Frame 7 Thread the 3 3 8 T shaped Lock Pin 73 into the nut on the Seat Support Frame to lock the Seat at desired height C Insert one Foam Tube 23 halfway through the hole on the Leg Developer 8 Push two Foam Rolls 86 onto the Foam Tube from both ends Plug two Foam Roll End Caps 459 into the Ends D Attach the Leg Machine Frame 431 to the Rear Base Frame 415 Secure it with two M10 x 3 5 8 Allen Bolts 96 one 5 1 x 2 Bracket 26 four 34 Washers 111 and two M10 Aircraft Nuts 109 E Attach the Rotating Cam Plate 432 to the Leg Machine Frame 431 Align the holes and insert the axle on the Lever Frame 33 through the holes Secure it with one Y 1 14 Washer 70 and one M12 Aircraft Nut 110 Do not over tighten the nut The Lever Frame needs to swivel freely on the pivot F Adjust and secure the Lever Frame 33 to the Cam 32 with a 4 T shaped Lock Pin 478 G Insert the axle on the Lever Frame Handle 34 into the opening on the Lever Frame 33 Secure it with one 1 14 Washer 70 and M10 Aircraft Nut 109
12. d by Escalade International Lid Pleasant Road Penllergaer Swansea SA4 9GE Tel 00 44 1792 222550 Fax 00 44 1792 895781 escaladesports co E mail info escaladesports co uk 8 9 IMPORTANT SAFETY PRECAUTIONS This Gym is built for optimum safety However certain precautions apply whenever you operate a piece of exercise equipment Be sure to read the entire manual before you assemble or use your Gym In particular note the following safety precautions Keep children and pets away from the Gym at all times Do not leave children unattended in the same room with the Gym The Gym is not a toy and therefore parents and guardians should be aware of the natural tendency for children to play leading to situations and behaviour for which the Gym is not intended If children are allowed to use the Gym their physical mental development and above all temperament should be taken into account Constant supervision is therefore needed Only one person at a time should use the Gym If the user experiences dizziness nausea chest pain or any other abnormal symptoms STOP the workout at once Consult a physician immediately Injuries may occur due to incorrect or excessive exercise Position the Gym on a clear leveled surface which is clear of all obstacles as not to restrict movement whilst exercising DO NOT use the Gym near water or outdoors Keep hands away from all moving parts Always wear appropriate clothing when exercising DO NO
13. e Frame Repeat Procedure C above to install a Pulley G Draw the Cable underneath the Pulley to the left open bracket on the Vertical Frame Install a Small Pulley to the bracket H Draw the Cable around the Small Pulley then attach the end the Cable to the open slot on the Left Butterfly Attach the Butterfly Base Cover 21 to the Butterfly Base 13 to cover the left and right pivots on the Butterfly Base Secure the Cover to the Pivots with two M10 x 34 Allen Bolts 103 and Y 34 Washers 111 J Align the holes and secure the Cover to the Butterfly Base with two M10 x 3 3 8 Allen Bolts 97 four Y Washers 111 and two M10 Aircraft Nuts 109 21 gt O ud Butterfly Cable Loop Diagram STEP 9 See Diagram 9 A Connect the Lat Bar 24 to the 167 Upper Cable 42 with two Hooks 90 and one Short Chain 75 B Attach the Abdominal Strap 85 to the U shaped Cable Connector 48 on the 215 Lower Cable 440 with a Hook 490 C Connect the Shiver Bar 422 to the 215 Lower Cable with two Hooks and a Long Chain 476 x DIAGRAM 9 24 STEP 10 See Diagram 10 A Attach one end of 75 Hip Thigh Cable 39 to the bracket on the Rotating Cam Plate 32 Secure it with one M10 x 1 Allen Bolt 102 two 32 Washers 111 and one M10 Aircraft Nut 4109 B Attach two Medium Pulleys 87 to the pulley bracket on the Leg Machine Frame 31 Attach a Doubl
14. e Pulley Bracket 101 to the two Medium Pulleys Align the holes and secure them with two M10 x 1 37 Allen Bolts 99 four Y Washers 111 and two M10 Aircraft Nuts 109 C Draw the Cable between the two Medium Pulleys and downward to the opening on the bottom of the Frame Attach a Pulley 44 to the opening Secure the Pulley 44 to the opening with one M10 x 3 3 8 Allen Bolt 97 two Pulley Bushings 53 and one M10 Aircraft Nut 109 D Draw the Cable underneath the Pulley to the open bracket behind the Frame Install a Pulley with one M10 x 1 Allen Bolt 99 two Y 32 Washers 111 and one M10 Aircraft Nut 109 E Draw the Cable around the Pulley then upward to the Single Floating Pulley Bracket 418 previously installed in Step 7 Secure the end of Cable to the bracket with M10 x 1 Allen Bolt 102 two Y 34 Washers 111 and one M10 Aircraft Nut 109 DIAGRAM 10 B 67 U Co Hip Thigh Cable Loop Diagram STEP 11 See Diagram 11 A Attach the two Weight Stack Covers 46 To Upper Frame 1 and Rear Base Frame 15 from each side B Secure the Weight Stack Covers to the Upper Frame and Rear Base Frame with four M10 x 34 Allen Bolts 103 and four Y Y Washers 111 DIAGRAM 11 TA CM 7 il 3 27 WEIGHT RESISTANCE CHART
15. ket 427 Repeat Procedure B above to install a Pulley Let the Brackets hanging for now Draw the Cable around the Pulley then upward to the opening on the Vertical Frame 44 Attach a Pulley to the opening Secure it with one M10 x 3 3 8 Allen Bolt 97 two Pulley Bushings 53 and one M10 Aircraft Nut 109 Insert the Cable through a Ball Stopper 47 Attach the Cable to a U shape Cable Connector 48 Secure the Connector with one M10 x 1 1 8 Allen Bolt 4100 two G 34 Washers 111 and one M10 Aircraft Nut 109 18 DIAGRAM 7 eX ee NS 5 E j N se 9 Lower Cable Loop Diagram STEP 8 See Diagram 8 amp Butterfly Cable Loop Diagram A Clip one end of the 83 Butterfly Cable 41 to the open slot on the Right Butterfly 10 B Draw the Cable to the open bracket on the right side of the Vertical Frame 44 Attach a Small Pulley 45 to the bracket C Secure it with one M10 x 1 9 Allen Bolt 99 two Y 34 Washers 111 and one M10 Aircraft Nut 109 D Draw the Cable around the Small Pulley to the right open bracket on the Rear Base Frame 15 Repeat Procedure C above to install a Pulley E Draw the Cable underneath the Pulley then upward to the Angled Double Floating Pulley Bracket 27 previously installed in Step 7 Repeat Procedure C above to install a Pulley F Draw the Cable around the Pulley then downward to the left open bracket on the Rear Bas
16. lled in Step 1 and Step 2 D Attach the Seat Support Frame 7 to the Vertical Frame 4 Secure it with two M10 x 2 5 8 Carriage Bolts 106 one 4 34 x 2 9 Bracket 25 two Y 34 Washers 111 and two M10 Aircraft Nuts 4109 E Attach the Leg Developer 8 to the bracket on the Seat Support Frame Secure it with one Leg Developer Axle 19 two M10 x 37 Allen Bolts 103 and two Y 34 Washers 111 Do not over tighten the Bolts Make sure the Leg Developer is able to swivel DIAGRAM 2 7 4 alil a f DID dre IT Sar Ir Sri e IS IS YH Y 09 NI La Pelis Jl LH o STEPS See Diagram 3 A Attach the Front Press Base 2 to the Upper Frame 1 Secure it with one 6 34 Front Press Base Axle 29 two 1 14 Washers 70 and two M10 Aircraft Nuts 4109 Attach the Front Press 3 to the Front Press Base Secure it with one 7 1 2 Front Press Axle 30 two O1 2 Washers 70 and two M10 Aircraft Nuts 109 Thread the 4 T shaped Lock Pin 78 into the hole on the Front Press to obtain the desired Front Press position Attach the Backrest Board 89 to the Backrest Support Frame 5 Secure it with two M8 x 1 5 8 Allen Bolts 113 and 5 8 Washers 112 Attach the Backrest Support Frame 5 to the Vertical Frame 4 Secure it with one M10 x 4 14 Allen Bolt 95 two Washers 111 and one M10 Aircraft Nut 109 Thre
17. the Front Press Base 42 Attach a Pulley to the opening Secure it with one M10 x 6 7 Allen Bolt 94 two 34 Washers 111 and one M10 Aircraft Nut 109 Draw the Cable around the Pulley then towards the upper opening on the Vertical Frame 4 Repeat Procedure B above to install a Pulley Draw the Cable around the Pulley and back to the lower opening on the Front Press Base Repeat Procedure D above to install a Pulley Draw the Cable around the Pulley then to the lower opening on the Vertical Frame Repeat Procedure B above to install a Pulley Draw the Cable underneath the Pulley then pull upward to the last opening on the back of the Upper Frame Repeat Procedure B above to install a Pulley Draw the Cable around the Pulley then downward Attach a Pulley to the top hole on the Double Floating Pulley Brackets 420 Secure the Pulley to the brackets with one M10 x 1 37 Allen Bolt 99 two Y 34 Washers 111 and one M10 Aircraft Nut 109 Let the Bracket hanging for now Draw the Cable around the Pulley then upward to the open bracket between the two Guide Rods Repeat Procedure J above to install a Pulley Draw the Cable around the Pulley then downward to the Selector Rod 28 Securely thread the Head Bolt at end of the Cable into the Selector Rod 15 DIAGRAM 6 Upper Cable Loop Diagram STEP 7 See Diagram 7 amp Lower Cable Loop Diagram A B C Attach the 215 Lower Cable 40 to the opening
18. ther damages with respect to any economic loss loss of property loss of revenues or profits loss of enjoyments or use costs of removal installation or other consequential damages or whatsoever natures The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein Your statutory rights are not affected ORDERING REPLACEMENT PARTS Replacement parts can be ordered by calling our Customer Service Department Monday to Friday 9am to 5pm Tel Fax 00 44 1792 222562 E mail customerservices escaladesports co uk When ordering replacement parts please give the following information Model Description of Parts Part Number Date of Purchase n AT 30
Download Pdf Manuals
Related Search