GardTec 590 User Manual
Contents
1. Service Rec rdase ie iiaeiai User Charts e nds ACE Instructions Programming ACE Keyfobs onto your System Page 1 NOOA ND DY 13 13 14 14 15 23 16 17 18 18 19 20 20 21 23 23 24 25 26 User Manual User Manual GARDTEC 590 591 Introduction Two types of display variation are available LCD giving two rows of 16 character English text and may be used on the Gardtec 591 and LED giving two 7 segment LED digits that may be used on the Gardtec 590 amp 591 Please take time to familiarise yourself with the type of equipment fitted to your premises as it will prove invaluable whilst using this manual User Code Types Four types of User Codes are available on the Gardtec 590 591 each user code type allows for different levels of access In total 7 User codes may be programmed by a Master Level User Code User number 1 will always be a Master Level User but the remaining 6 User Codes may be programmed by a Master Code to the required level of access These may be changed at any time via a Master level code The User Code levels available and the functions available for the levels are 1 Set Only Only Allows for the setting of the system 2 Main User Allows Setting Part Setting Zone Remove if programmed by engineer System Test Unsetting Reset after Alarm if programmed by engineer 3 User Allows Setting2. Then YES Enter Hrs Mins Then YES Do you want to Set DATE TIME lt lt lt lt UN SET gt gt gt gt 07 Jun 23 30 02 GARDTEC 590 591 User Initiating Remote Access Optional User Manual Access Remote allows your installation company to examine your system and re program system settings as you need the changes without the need for an engineer to visit your premises If your system has remote communications fitted your installation company may have programmed the system so that you initialise the Access Remote call usually on lines with incoming calls barred To initiate the Remote Call follow the instructions below 1 2 Note Negotiate with your installation company when you should initiate the Remote Call With the display showing Enter a Master Code the display will show User Names on 816 amp 840 Only Press NO seven times the display will show Press YES the display will show Until Dialling commences Then Until Connection Then When your installation company has finished the display will show In the event of any errors the display will show Page 11 lt lt lt lt UN SET gt gt gt gt 01 JAN 18 58 01 Do you want to Set Do you want to Access Remote Please WAIT
3. f n lt lt lt lt UN SET gt gt gt gt 1 With the display showing 01 JAN 18 58 01 2 Enter a Master or Main type code the display will show for example eae Walit tO i 3 Press 1 2 or 3 for Part 1 2 or 3 the display will show for example Non Part 1 15 4 The exit tone may or may not be heard dependant on the system settings 5 Exit the premises or retire to an unprotected part of the system At the end of the exit time either the exit sounder will stop or a single beep will be emitted dependant on system settings Page 4 GARDTEC 590 591 Removing Zones Master amp Main codes only User Manual If programmed by the installation company individual zones may be removed this may only be done by a Master or Main level of code 1 Note With the display showing Enter a Master or Main level code the display will show Press NO the display will show Press YES the display will show Enter the zone number you wish to remove followed by YES pressing NO will un remove a zone the display will show Repeat step 5 until you have removed all the required zones Press 0 to escape the display will show Press YES the continuous exit tone will sound Exit the premises via the authorised exit route the exit tone will change as detectors are violated When the premises are secure listen that the exit tone returns to the continuous tone
4. Please WAIT Dialling Please WAIT Connect lt lt lt lt UN SET gt gt gt gt 01 JAN 18 58 01 ERROR Try Again User Manual GARDTEC 590 591 Resetting After an Alarm Your installation company will have programmed the reset modes for your system so that it complies to your insurance company and legislation requirements Your installation company will have informed you as to the type of reset that your system is set for Before attempting to reset your system ensure that the system is Un set 1 If the system is programmed for any code reset enter a user followed by YES if Master or Main code is used the exit tone will sound and the display will show for example EXIT Now All Zones ON 15 2 Enter the code again to abort the setting 3 The system is now reset Or If a higher level of code is required one of the following displays will be shown Can t Set Use Use a Master code to reset the system Master Code Or Can t Set Use Call the installation company ENGNR Code Or Can t Set Use Call the installation company and quote ENG Cee lees the number given Or Can t Set Use Anti Code 1234 Page 12 GARDTEC 590 591 User Manual 4 To reset the system with an anti Code contact the central station or engineer as inst
5. Part Setting Reset after Alarm if programmed by engineer Unsetting 4 Master Allows Setting Unsetting Zone Remove if programmed by User 1 always Master engineer Test System View Log Chime On Off User Codes Set Time Date Reset After Alarm if programmed by engineer Unsetting Page 2 GARDTEC 590 591 User Manual Setting The System This section is for systems fitted with LCD keypads for LED keypads please refer to page 13 1 With the display showing lt lt lt lt UN SET gt gt gt gt 01 JAN 18 58 01 2 Enter the User code followed by YES if Master or Main type code has been used The display will show EXIT Now and a continuous exit tone will sound All Zones ON 15 3 Exit the premises via the authorised exit route the exit tone will change if any detectors are violated during exit 4 Once the premises are secure listen that the exit tone returns to the continuous tone 5 Wait until the exit tone finishes before leaving Unsetting The System 1 Enter the premises via the authorised entry route the broken entry tone will sound proceed to the keypad 2 At the keypad enter a valid code the display will show lt lt lt lt UN SET gt gt gt gt i 01 JAN 18 58 01 3 The system is now unset Page 3 User Manual GARDTEC 590 591 Part Setting The System using Master amp Main type codes
6. Time Note When using LED keypads the Date amp time will only be displayed when the 3 key is pressed whilst viewing the Log 1 With the display showing U Nenter a Master code 2 The display will show S E 3 Press NO six times the display will show Dt flashing 4 Press YES the display will show D enter the day and month followed by YES e g 0706 for 7th June 5 The display will show t enter the time using the 24Hr clock followed by YES e g 2330 for 11 30pm 6 The display will show Dt flashing 7 If you wish to re program the time return to step 4 Or To return to the Unset condition press 0 User Initiating Remote Access Users should only initiate Remote Access when instructed to do so by the installation company 1 With the display showing U Nenter a master level code then press NO seven times the display will flash Ar 2 Press YES the display will show WX Wait then D I Dialling then N Connected 3 When the installation company has finished the display will return to UN Page 19 User Manual GARDTEC 590 591 Resetting After An Alarm Your installation company will have programmed the reset modes for your system so that it complies to your insurance company and legislation requirements Your installation company will have informed you as to the type of reset that your system is set for Before attempting to reset your system ensure that the system is Un set 1 If the system
7. Wait until the exit tone finishes before leaving Zone remove is only effective for the one set Page 5 lt lt lt lt UN SET gt gt gt gt 01 JAN 18 58 01 Do you want to Set Do you want to REMOVE Zones Enter Zone No then YES or NO Enter Zone No then YES or NO Do you want to Set User Manual Testing The System Master amp Main codes only 1 GARDTEC 590 591 With the display showing lt lt lt lt UNSET gt gt gt gt 01 JAN 18 58 01 Enter a Master or Main level code the display will show Bs want to User Names on 816 amp 840 Only Press NO the display will show Do you want to REMOVE Zones Press NO the display will show TIC TEST the System Press YES the display will show 1 Status 4 Strobe p ay 6 Sounder 9 Bell for 3 seconds Then for example Al Zones OKS TESTING Pressing 1 will enter zone Status mode All zones will show on the display and will be deleted as each zone is triggered Press 0 to escape Pressing 6 will silence the internal sounder Pressing 4 will toggle the Strobe On Off Pressing 9 will toggle the Bell On Off Whilst in Test mode any zones violated will sound the internal sounder if it has not been silenced and sho
8. Master or Main level code the display will show SE flashing Press NO twice the display will show t E flashing Press YES the display will show t A press YES if you wish to test all areas or press NO until the area you wish to test is displayed then press YES The display will show t E if all zones are clear Whilst in test mode Pressing 6 will silence the internal sounders Pressing 4 will toggle the strobe On Off Pressing 9 will toggle the Bells On Off When you have finished testing the system press 0 twice to return to the Unset condition Page 16 GARDTEC 590 591 User Manual Viewing The Event Log Master code only Note With the display showing U N enter a Master code The display will show S E flashing press NO three times The display will show L O flashing Press YES the display may show for example A Lthis is the most recent event Whilst viewing the Log Pressing NO will move back to the previous event Pressing YES will move forwards to the next event Pressing 7 will take you back to the first event of the previous day Pressing 9 will take you forwards to the first event of the next day Pressing 3 will display the Date Time in the format Day of month two digits Month two digits Hour two digits Seconds two digits When you have finished viewing the Log press 0 twice to return to the Unset condition A complete list of possible LED displays is given in the section LED Di
9. the same system the bution on the fob MUST be held down continuously between programming onto the first and other ACE receivers Note In all cases when the ACE is used only Master amp Main user levels will allow part setting via the keyfob Other code levels will only allow part setting in conjunction with the keypad Page 26 GARDINER TECHNOLOGY Gardiner Technology Ltd Queensway Rochdale Lancashire OL11 1TQ United Kingdom Internet http www gardiner technology com e mail sales gardiner technology com CE168X BIA Brith 5 INVESTOR IN PEOPLE fut Ceniki Mo a5 Te PR5075 Rev1 0
10. GARDINER TECHNOLOGY GARDITEC 990 591 LCD User Instructions amp LED User Instructions GARDTEC 590 591 Contents Using LCD Keypads Introduction ist snif T User Code Types rresaememannnbede nt Setting The System 0 0 ceeceeeeceesceeseeeeseeseeeeeeeseaeeeaeeteas Unsetting The System ceceeseeeeeeeneeeeeeseneeeeeeeeaeeeees Part Setting The System REMOVING Zones Testing The System Viewing The Event Log Changing The Chime Status Programming User Codes escceceeeeeeeeeeeeeeeeeeeeaees Programming Time amp Date iecere User Initiating Remote Access Resetting After An Alarm Resetting After Mains Failure Using LED Keypads Setting The System 0 0 eeceeeeeseseeeeteeseeeeeeeteaeeeaeeteas Unsetting The System eeceeseeseeeeeeeeeeeeeneeseeeeeeeeaas Part Setting The System Area Settings derriere ie untrsstess ee REMOVING Zones Testing The System Viewing The Event Log Changing The Chime Status Programming User Codes cecccseseeseeeeceeeeeeeeeeeees User Initiating Remote Access Resetting After An Alarm Resetting After Mains Failure LED Display Glossary System Attributes
11. age 22 Page 23 User Manual User Chart GARDTEC 590 591 Please use this chart to indicate what user names have been programmed onto your system and those that are in use User Notes Page 24 GARDTEC 590 591 User Manual ACE User Instructions ACE Advanced Control Equipment allows control of your Gardtec 590 591 system via Infra Red Remote control Ace is available built in to a range of keypads or as a stand alone unit control is via neat remote keyfob s We strongly advise that User Number 1 is not used for ACE in order that the user retains control of the programming functions Setting the System with ACE 1 Point the keyfob at the ACE receiver and press the button 2 When the exit tone sounds exit the premises in the usual way Part Setting the System with ACE 1 Point the keyfob at the ACE receiver and press the button 2 When you hear the exit tone press the keyfob button again within 3 seconds for Part Set 1 or Press 1 2 or 3 on the receiver keypad for the Part Set you require Unseiting the System with ACE 1 Enter the premises via an authorised entry point 2 Point the keyfob at the receiver and press the button Page 25 User Manual GARDTEC 590 591 Programming ACE Keyfobs onto your System Two modes are available for ACE these are Normal amp High Security Please check the User Information Chart on page 2 noting the mode of your ACE control Normal Security In t
12. ammed The display will scroll showing the code types available see user types or display Enter the required type followed by YES the display will show If you wish to program other User Codes return to step 4 Or Press 0 to return to Page 9 User Manual lt lt lt lt UN SET gt gt gt gt 01 JAN 18 58 01 Do you want to Set Do you want to Prog USER CODES Enter User No 1 7 Then YES Now Enter Code Then YES Choose Type O XXXXXX 1 XXXXXX Do you want to Prog USER CODES lt lt lt lt UN SET gt gt gt gt 01 JAN 18 58 01 User Manual Programming Time amp Date 1 With the display showing Enter a Master Code the display will show User Names on 816 amp 840 Only Press NO six times the display will show Press YES the display will show Enter the Day Month ie 0706 for 7th June followed by YES The display will show Enter the time using 24Hr Clock ie 23 30 for 11 30pm followed by YES the display will show Press 0 the display will show Page 10 GARDTEC 590 591 lt lt lt lt UN SET gt gt gt gt 01 JAN 18 58 01 Do you want to Set Do you want to Set DATE TIME Enter Day Month
13. his mode up to fourteen keyfobs may be programmed onto a single user number 1 Follow the procedure for programming user codes to the point when the user code is entered 2 Point the keyfob at the ACE unit and press the button on the fob 3 Repeat this procedure for any other fobs you wish to be programmed using the same user number each time e g User 1 or User 2 etc each time 4 If more than one ACE receiver is fitted fobs need to be programmed onto all ACE receivers yet again the same user number should be used Note When programming the fob onto more than one receiver on the same system the button on the fob MUST be held down continuously between programming onto the first and subsequent ACE receivers High Security In this mode each keyfob will occupy a User number The number of keyfobs that may be used is limited by the maximum number of user codes available on the system up to a maximum of fourteen 1 Follow the procedure for programming user codes to the point when the user code is entered 2 Point the keyfob at the ACE unit and press the button on the fob 3 Repeat this procedure for any other fobs you wish to be programmed using a different user number each time e g User 1 or User 2 etc each time 4 If more than one ACE receiver is fitted fobs need to be programmed onto all ACE receivers retaining the same user number for each individual fob Note When programming the fob onto more than one receiver on
14. is programmed for any code reset enter a user followed by YES if Master or Main code is used the exit tone will sound and the display will show for example E 2 Enter the code again to abort the setting 3 The system is now reset Or If the display shows Er when you attempt to reset it refer to the programmed reset mode and take the appropriate action as follows Reset Type Action Master Code Use a Master code to set and abort setting Engineer Code Call the installation company Engineer Anti Code Call the installation company Anti Code When you try to set the system make a note of the four digit number given on the display call the installation company or central station for an Anti Code and proceed as shown from step 4 4 To reset the system with an Anti Code enter the number given by the central station or installation company into the keypad this may contain the YES amp NO keys 5 The system is now reset Resetting After Mains Failure After a mains failure the user will have to enter his her code twice in order to operate the system Page 20 GARDTEC 590 591 LED Display Glossary Displays During Normal Use UN E E E amp AL FB eCB eBB PL PC et4 ER System Unset AC The system is full setting SE The system is fully set rE The system is part 1 setting tE The system is part 1 set H The system is part 2 setting UC The system is part 2 set Dt The system i
15. lay will show the Eand The two bottom bars if Part 1 has been selected The top and bottom bars if Part 2 has been selected The bottom bar only if Part 3 has been selected 3 The exit tone may or may not be heard dependant on the system settings 4 Exit the premises or retire to an unprotected part of the system At the end of the exit time either the exit tone will stop or a single beep will be emitted dependant on system settings Page 14 GARDTEC 590 591 User Manual Removing Zones Master amp Main codes only If programmed by the installation company individual zones may be removed this may only be done by a Master or Main level of code 1 With the display showing U NEnter a Master or Main level code 2 The display will show SE flashing press NO 3 The Display will show r E flashing press YES 4 The display will show r 5 Enter the zone number you wish to remove followed by YES 6 The display will show r 7 If you wish to remove other zones return to step 5 Or To escape press 0 the display will show S E flashing 8 Press YES to start setting the system 9 Exit the premises or retire to an unprotected part of the system At the end of the exit time the exit tone will stop provided the system was clear Note Zone remove is only effective for the one set Page 15 User Manual GARDTEC 590 591 Testing The System Master amp Main codes only 1 With the display showing UN Enter a
16. ructed by the installation company and quote the source given by the display 5 The central station or engineer will give a return Anti Code this may contain the YES amp NO keys for example 5 YES 2 4 6 Enter this Anti Code into the keypad 7 The system is now reset Resetting After Mains Failure After a mains failure the user will have to enter his her code twice in order to operate the system Using LED Keypads This section is dedicated to using LED keypads Twin Seven Segment Setting The System 1 With the display showing UN 2 Enter the User Code followed by YES if Master or Main type code has been used 3 The display will show E and the exit tone will sound Exit the premises via the authorised exit route the exit tone will change if any detectors are violated during exit 4 Once the premises are secure listen that the exit tone returns to the continuous tone 5 Wait until the exit tone finishes before leaving Page 13 GARDTEC 800 Series GARDTEC 590 591 Unsetting The System 1 Enter the premises via the authorised entry route the broken entry tone will sound 2 Proceed to the keypad enter a valid user code the display will show UN 3 The system is now Unset Part Setting The System using Master amp Main type codes 1 With the display showing U NEnter a Master or Main type code 2 The display will show S E flashing Press 1 2 or 3 for Part 1 2 or 3 the disp
17. s follows 1 With the display showing lt lt lt lt UN SET gt gt gt gt 01 JAN 18 58 01 2 Enter a Master Code the display will show for example Do you want to Set 3 Press NO four times the display will show Do you want to Change Chime 4 Press YES the display will show for example Chime is Off ok Or Chime is On ok 5 Press NO to change the status of the Chime Do you want to then press YES the display will show Change Chime lt lt lt lt UN SET gt gt gt gt 01 JAN 18 58 01 6 Press 0 to escape the display will show Page 8 GARDTEC 590 591 Programming User Codes Master code only 1 Note With the display showing Enter a Master Code the display will show User Names on 816 amp 840 Only Press NO five times the display will show Press YES the display will show 1 7 displayed on 800 amp 816 Enter the user number 1 to 7 that you wish to program followed by YES the display will show Enter the code you require codes may be 4 5 or 6 digits followed by YES Entering 000000 will delete an existing code If the code already exists or is a duress of another code an error will be shown choose another code and return to step 6 The display will show not if user 1 is being progr
18. s part 3 setting LO The system is part 3 set s otal has occurred press NO Ww Fuse blown or battery volts low EN Control box tamper EN bell box tamper Telephone Line fault or coms fail Power Cut Tamper keypad 4 may show 1 to 4 Reset is required by a higher level code or an error has Page 21 User Manual occurred whilst programming Reset by Anti Code is required flashing Do you want to Set Remove zones Test system Change Chime Program User codes Program date time Log Waiting for numeric input Wait system in use Engineer code reset required flashing Call Engineer User Manual GARDTEC 590 591 GARDTEC 590 591 User Manual Displays Whilst Viewing Log System Attributes 04 Alarm occurred because of zone Zone No Zone Type Location Part Info 4 was activated Front Door 1 amp 2 004 Alarm occurred because of tamper on zone 4 04 flashing zone 4 was removed LR Telephone Line restored PR Power restored Service Record D3 Duress code by user 3 Date Comments Signature RE cWatehdog tesel En Si AR Alarm was reset ed EE BO belis on En EE Gt Uger cu CITE EE EE F2 Fire activated from alert keys on Tl keypad 2 En S EE Ad Aetadtasd tonen koison C O oooO keypad 2 E E ae En Pa PAGES aiai apys lt lt lt lt 7 RASE EE EE tF A zone on test has failed Alarm Reset Type Tamper Reset Type RL read Log Service Company P
19. splay Glossary Page 17 User Manual GARDTEC 590 591 Changing The Chime Status Master code only The Chime zones will have previously been programmed by your installation company A Master level code may change the status of the chime between On and Off To do so proceed as follows 1 With the display showing UN enter a Master code 2 The display will show S E flashing 3 Press NO four times the display will show H 4 Press YES the display will show OF or ON 5 Press NO to change the Chime status 6 When you have finished press 0 twice to return to the Unset condition Programming User Codes Master code only Please refer to pages 2 amp 34 for details of codes already programmed onto your system 1 With the display showing UC enter a Master code 2 The display will show S E 3 Press NO five times the display will show UC flashing 4 Press YES the display will show U 5 Enter the User number you wish to program 1 to 7 for 800 followed by YES 6 The display will show O Enter the required code 4 5 or 6 digits followed by YES Entering 000000 will delete an existing code 7 The display will show t enter the code type from the following list followed by YES Code Types may be seen at the beginning of this manual Page 18 GARDTEC 590 591 User Manual 9 If you wish to program other User codes return to step 4 Or To return to the Unset condition press 0 Programming Date amp
20. w on the display When you have finished testing the system press 0 twice the display will show lt lt lt lt UNSET gt gt gt gt 01 JAN 18 58 01 Page 6 GARDTEC 590 591 User Manual Viewing The Event Log Master code only 1 With the display showing lt c lt lt UNSET gt gt gt gt 01 JAN 18 58 01 2 Enter a Master Code the display will show for example Do you want to Set 3 Press NO three times the display will show Do you want to View the LOG 4 Press YES the display will show While Viewing for 3 seconds 1 Printer On Off Then for example Read Log 01 JAN 18 58 01 5 This is the most recent event in the log Whilst viewing the Log Pressing NO will move back to the previous event Pressing YES will move forward to the next event Pressing 7 will take you back to the last event of the previous day Pressing 9 will take you forward to the first event of the next day 6 When you have finished viewing the Log press 0 twice the display will show lt lt lt lt UN SET gt gt gt gt 01 JAN 18 58 01 Page 7 User Manual GARDTEC 590 591 Changing The Chime Status Master code only The Chime zones will have previously been programmed by the installation company A Master level code may change the status of the Chime between On and Off To do so proceed a
Download Pdf Manuals
Related Search