Home

en-us Use and Care Manual, Installation Instructions Washer

1. TATA RATE TS LDN Hot water AquaShield hose 6 Cold water AquaShield hose NOTICE f any parts are missing please notify your dealer immediately Set up on a pedestal with drawer Pedestal item number WMZ 20490 Mount washer on the pedestal according to the instructions in the installation kit Installation checklist Review the following list and check off each step as it is completed during installation Installation Step Page Remove the trans port bolts Page 12 If installing to a pedestal base complete the base installation before removing the transportation bolts Completely remove all four shipping bolts keeping the bolt and bushing assem blies intact Connect the water supply hose and drain hose Connect the electrical power Slide the washing machine into its final location Level the washing machine as low as possible Remove the trans port bolts Page 12 Water connections Page 13 Electrical connection Page 16 Leveling the washer Page 15 12 V Installation Step Before washing laundry run Before loading the Drum Clean program your first load of laundry Page 19 Page Importance of installing on a solid level floor Your new Bosch washing machine utilizes high spin speeds to achieve superior water removal from your laundry resulting in reduced drying time It is important to install your washing machine on a floor that will p
2. To reduce the risk of fire or electrical shock DO NOT use an extension cord or an adapter to connect the washing machine to the power supply WARNING ELECTRICAL SHOCK HAZARD To reduce the risk of electrical shock e Only pull out the power cord by the plug end and never by the cable as this could damage it e Never touch or hold the plug end or power cord with wet hands e Never unplug the plug end or power cord during operation Grounding Instructions A Volts 240 WARNING ELECTRICAL SHOCK HAZARD This appliance must be grounded In the event of malfunction or breakdown grounding will reduce the risk of electric shock by providing a path of least resistance for the electric current This appliance is equipped with a cord that has an equipment grounding conductor and a grounding plug The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances Do not modify the plug provided with the appliance If the plug will not fit into the outlet have a properly grounded outlet installed by a qualified electrician Do not cut remove or bypass the grounding prong on the washer power cord plug The washer power cord plug must be easily accessible when the washer is operating When unplugging or plugging in the washer power cord grasp the plug end Do not pull on the cable to unplug the washer The household electrical supply must be
3. installer or an authorized service center Do not attempt to repair the appliance yourself Any work performed by unauthorized personnel may void the warranty If you are having a problem with your washing machine and are not pleased with the service you have received please follow these steps 1 Contact your installer or the Authorized Service Provider in your area and explain to them why you are not satisfied This will usually correct the problem 2 If after working with your installer or service technician the problem still has not been resolved to your satisfaction please let us know either by writing to us at BSH Home Appliances 1901 Main Street Suite 600 Irvine CA 92614 or calling us at 1 800 944 2904 When writing or calling please have the following information available e E Nr model number example WTVC3300UC 27 e FD serial number e Date of Original Purchase receipt required e Date Problem Occurred e Explanation of Problem If writing please also include a daytime telephone number and a copy of the sales invoice When calling Customer Service please be ready to provide the model number E Nr and FD serial number This information will help provide the best support for your washer Additional information is available at our website www bosch home com us Your washing machine is intended for e Only household use and in a non commercial environment e Household use only washing mach
4. washed soaked or spotted with gasoline dry cleaning solvents other flammable or explosive substances as they give off vapors that could ignite or explode Do not add gasoline dry cleaning solvents or other flammable or explosive substances to the wash water These substances give off vapors that could ignite or explode Under certain conditions hydrogen gas may be produced in a hot water system that has not been used for 2 weeks or more HYDROGEN GAS IS EXPLOSIVE If the hot water system has not been used for this length of time turn on all hot water faucets and let the water flow out of each faucet for several minutes before using the washing machine This will release any accumulated hydrogen gas As the gas is flammable do not smoke or use an open flame while carrying out this procedure Before the appliance is removed from service or discarded remove the door to prevent children from playing or hiding inside Also remove the power cord plug Do not allow anyone to climb lean or hang on any part of the washer including any protruding components such as the appliance door or a pullout shelf Use caution when draining hot water from the washer drum such as during pump maintenance or when using the emergency door open procedure Do not reach into the appliance if the wash drum is moving Do not tamper with the controls Do not repair or replace any part of the appliance or attempt any service unless specifically recomm
5. 23 Preparing the laundry rvvvvrvrrrrnvrsssnrrrnnnssnsssssrrrrvrrrevennvsnenne 23 Sorting the Laundry screen era 23 Identifying and treating stains in 23 Laundry detergents and additives 24 Adding the correct amount of HE detergent asss 24 Program selection table nnnernnnnnnvennnnnnnennnnnnvennnnnnr 25 TN 26 EVENING NEA sverdene 26 SOI uil 26 Default Program and Option settings 27 Changing the temperature range wrununnnnvnnvvrnnnssrrnvsrnne Of Changing the spin Speed range sessssssssseririrere Of ANN Of Additional Program Option settings 27 EU Of GENE S elica 27 SpeedPerfect DD 27 Cleaning and maintenance 1 28 Cleaning the housing and control panel 28 GE ge ka 010 0 EE RE 28 Descaling the Washer rrrvvnnnnnnnerrnnnnnnnnnnnrnnssnnssnsvrrrvverevene 28 Cleaning the detergent dispenser tray 28 Cleaning the water inlet strainers 28 Gleaning ine drain PUMP saved 29 Troubleshooting ci 31 Emergency door lock release i 31 General Troubleshooting srrrrverrrrrerrrrrrrrvevveerrrrrrsrrnnr 31 Error MESSAGES 34 Customer service nuuvnnnunnnnnnnnnnnnnnnnnnnnnnnnnennnuennnnunnnnuene 34 STATEMENT OF LIMITED PRODUCT WARRANTY 35 What this Warranty Covers amp Who it Applies t0 35 Additional information on products accessories
6. THE MANUFACTURER BE LIABLE FOR CONSEQUENTIAL SPECIAL INCIDENTAL INDIRECT BUSINESS LOSS AND OR PUNITIVE DAMAGES LOSSES OR EXPENSES INCLUDING WITHOUT LIMITATION TIME AWAY FROM WORK HOTELS AND OR RESTAURANT MEALS REMODELLING EXPENSES IN EXCESS OF DIRECT DAMAGES WHICH ARE DEFINITIVELY CAUSED EXCLUSIVELY BY BOSCH OR OTHERWISE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES AND SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE No attempt to alter modify or amend this warranty shall be effective unless authorized in writing by an officer of BSH How to Obtain Warranty Service To obtain warranty service for your Product you should contact the nearest Bosch Customer Service Department BSH Home Appliances Corporation 1901 Main Street Suite 600 Irvine CA 92614 800 944 2904 BOSCH 1901 Main Street Suite 600 Irvine C e 1 800 944 ho ANA ee 9504
7. for the fabric Beverages and juices tea coffee red wine fruit vegetables Treatment Pretreat stain Wash using cold water Sorting the Laundry sort laundry items according to color degree of soiling and recommended wash temperature range Wash white items separately from colored items Otherwise white items may tend to become grey Proteins and carbohydrates blood egg milk starch Treatment Rinse immediately Observe laundry care labels in cold water If stain remains soak in cold a water with an enzyme prewash extra hot hot warm cold Soot earth sand pigments red clay such as soiling of tennis clothing Brush off residue if present Pretreat or soak with a laundry product containing enzymes 23 Removing stains e Remove pretreat stains as soon as possible after they have occurred e Dab with a soapy solution Do not rub e Select an appropriate wash cycle and wash the item Several washing cycles may be required in order to remove stubborn or dried in stains Laundry detergents and additives Adding the correct amount of HE detergent amp WARNING To avoid risk of poisoning keep detergents and cleaning products out of the reach of children Avoid overuse of detergent Measure out the detergent according to e The amount of laundry e The degree of soiling Sorting the Laundry Page 23 e The water hardness This information can be obtained from your local wat
8. in a shorter time with a washing result comparable to that of the standard program Note Do not exceed the maximum load Program selection table Page 25 27 Cleaning and maintenance Your washer is designed to give you many years of service Observe the following instructions to maintain and protect your washer and keep it in top operating condition A WARNING RISK OF ELECTRIC SHOCK HAZARD To avoid risk of electric shock always disconnect the washer from the power outlet prior to cleaning Never clean the washer with a pressure washer Cleaning the housing and control panel A WARNING RISK OF EXPLOSION To avoid risk of explosion never clean the washer with flammable solvents AS required you may clean the washer housing and control panel use hot soapy water or a mild non abrasive cleansing agent Dry with a soft towel Remove residue immediately Do not use high pressure spray Cleaning the drum Metallic debris left in the drum can produce rust spots on the drum Never use steel wool to try to remove these Use a chlorine free cleansing agent and follow the manufacturer s instructions Descaling the washer Provided that you use correct amounts of detergent with your wash loads descaling is not necessary If descaling the washer drum does become necessary please follow the descaling product manufacturer s instructions small amounts of descaling agent can be used to remove
9. it is level side to side and front to rear 5 Press down on each corner of the washer top to make sure the washer doesn t wobble There should be no give or movement All four washer feet should press equally against the floor This is just as Important as the washer being level to prevent vibration 6 When the washer is level and does not wobble lock the washer feet in place by tightening the locknuts against the washer bottom Be sure to do this without changing the height of the foot hold the foot while tightening the locknut 15 Procedure for adjusting the washer feet After determining which washer feet need to be extended have someone lift up on the washer slightly to take pressure off the foot to be adjusted Turn the grey plastic foot to extend it downward as far as necessary to raise the corner of the washer the correct amount to level the washer When the height of the foot is correct use a 17 mm open end wrench to tighten the locknut against the washer bottom The locknut should be tight against the bottom of the washer to lock the foot in place Electrical connection A WARNING ELECTRICAL SHOCK HAZARD Improper connection of the equipment grounding conductor may result in electric shock Have the appliance checked by a qualified technician or licensed electrician if you are in doubt as to whether the washer has been properly grounded WARNING ELECTRICAL SHOCK HAZARD
10. liter 1 pint of water and pour this mixture into the detergent compartment not with waterproof fabrics To prevent use less detergent for future wash loads To prevent always load the washer with a mixture of large and small wash items easier to distribute in the drum Add more laundry To prevent always load the washer with a mixture of large and small wash items easier to distribute in the drum Immediate fix mix 1 tablespoon of fabric softener with 1 2 liter 1 pint of water and pour this mixture into the detergent compartment not with waterproof fabrics To prevent use less detergent for future wash loads Select a spin speed setting Low Med or High Brush off when laundry is dry or execute the program Rinse Mix small and large laundry items together in the load to minimize this effect Check to be sure the washer is level and all four feet press equally against the floor Transport bolts removed Remove the transport bolts Page 12 33 Error messages Display Fault Measure flashes Door not closed properly Check to be sure no laundry Is caught in the washer door Close the door securely amp Cold water tap not turned on Turn on the cold water tap Supply hose for cold water kinked Eliminate the cause replace the hose if damaged or pinched closed Strainer in water supply hose Clean the water inlet strainer clogged Cleaning the water inlet strainers Page 28 Cold water pressur
11. or blouses that have been sweated in or worn several times Also tea towels hand towels or bed linen used for up to one week Net curtains without nicotine stains that have e Empty all pockets to ensure no loose debris coins not been washed for up to a half year keys other hard objects are placed in the washer e Heavy soiling drum Visible soiling and stains This could include kitchen e Close any fasteners Such as zippers and hooks that towels fabric napkins baby bibs children s outer could cause laundry to catch or become entangled clothing or football jerseys and shorts stained with grass and or earth Also could include working clothes a such as overalls and jeans and other clothing worn for e Turn trousers and knitted wear inside out prior to outside work and activities such as gardening home washing and yard maintenance or worn during sports activities e Place small items such as socks and handkerchiefs l i and underwired bras into a mesh bag prior to washing Identifying and treating stains e Remove any foreign objects or non washable parts a Oils and grease normal body skin oil cooking oils fats sauces mineral oil or wax containing fat oil Treatment scrape residue from fabric Pretreat Wash using hottest water safe for the fabric For heavy stains apply non flammable dry cleaning fluid to back of stain replacing towels under stain frequently Rinse thoroughly and wash using hottest water safe
12. provide you with any concessions including repairs pro rates or Product replacement once this warranty has expired 35 Warranty Exclusions The warranty coverage described herein excludes all defects or damage that are not the direct fault of Bosch including without limitation one or more of the following Use of the Product in anything other than its normal customary and intended manner including without limitation any form of commercial use use or storage of an indoor product outdoors use of the Product in conjunction with air or water going vessels e Any party s willful misconduct negligence misuse abuse accidents neglect improper operation failure to maintain improper or negligent installation tampering failure to follow operating instructions mishandling unauthorized service including self performed fixing or exploration of the appliance s internal workings e Adjustment alteration or modification of any kind e A failure to comply with any applicable state local city or county electrical plumbing and or building codes regulations or laws including failure to install the product in strict conformity with local fire and building codes and regulations e Ordinary wear and tear spills of food liquid grease accumulations or other substances that accumulate on in or around the Product e Any external elemental and or environmental forces and factors including without limitation rain w
13. replacement parts and services can be found at www bosch home com and in the online shop www bosch eshop com Questions 1 800 944 2904 www bosch home com 1901 Main Street Suite 600 Irvine CA 92614 We look forward to hearing from you Important information Purchase information Please take a moment to record the following basic information about your new Bosch washer This information will be helpful in the event you need to contact Customer Service or would like to order accessories or replacement parts The E Nr model number and the FD serial number are found on the rating plate label see illustration The model number includes the slash and a two digit number eg 27 Please be sure to include the final 2 digit number when filling in your model number This helps make sure any parts you may need are correctly matched to your specific machine Date of Purchase Where Purchased E Nr ex WFVC5330US 27 FD ex FD 9005 90001 Customer service Your washer does not require any special care other than the maintenance and care mentioned in this manual If you have a problem with your washer please consult Troubleshooting Page 31 This may save you money If a technician comes out to advise you of information that is in the Troubleshooting table you may be charged even if your washer is still under warranty If problems persist and service becomes necessary contact your dealer
14. s instructions clean first if necessary Dyeing bleaching If fabrics are heavily soiled reduce the load h Dye should only be used in normal household quantities Salt may damage stainless steel Always follow the dye manufacturer s instructions Do not use the washing machine to bleach clothes Soaking 1 Pour soaking agent detergent into compartment II in accordance with the manufacturer s instructions Turn the program selector to Cotton Normal Cold program 3 Touch Start Pause 4 After approximately ten Minutes touch Start Pause 5 After the required soaking time touch Start Pause again to continue or change the program NOTICES e Load laundry of the same color e No additional detergent is required the soaking solution is used for washing 26 Default Program and Option settings At the factory temperature and spin speed options and cycle duration Finish in time are pre set for all cycles After selection of the cycle these values are displayed in the display field You can change the default settings as follows Changing the temperature range Before and during the cycle you can change the default temperature range depending on the cycle progress Press the appropriate button until the desired setting IS displayed The maximum temperature range that can be set depends on the cycle selected Changing the spin speed range Before and during the cycle you can change the spin s
15. the water to finish draining from the drum When finished replace the sealing cap into the end of the hose and restore the hose to its storage location 30 6 Turn the pump cover counterclockwise to remove it A small amount of residual water may flow out when the cover is removed Clean the interior of the pump housing removing any debris or foreign objects Check to be sure the impeller wheel at the back of the pump housing can now turn freely Remove any lint debris or detergent residue from the threads of the pump cover and the pump cover housing Replace the pump cover by screwing tightly into position Handle must be vertical 7 Reinstall the protective film over the pump access using both screws 8 Snap the service cover in place at the hinges and close it Wipe up any spilled water NOTICE In order to prevent detergent from flowing unused into the drain during the next wash cycles pour 0 26 U S gallons 1 liter water into the chamber Il Turn the cycle selector to the Drain and touch the Start Pause button Troubleshooting Emergency door lock release In the event of a power interruption the program will continue running when the power supply has been restored If the washer door must be opened and the normal door unlock procedures do not work the emergency door lock release rod can be actuated to open the door A WARNING RISK OF SCALDING To avoid risk of scalding allow water to cool d
16. touches the discharge water water drained from washer it the discharge water can be sucked back into the appliance and may damage the appliance or textiles Make sure that e There is no stopper in the sink drain e The end of the hose does not touch the discharge water e The sink drain is free flowing and not partially clogged Attach the drain hose securely to the wash basin NOTICE In any multi story installation the washer should be installed on a drained floor to prevent water damage to rooms below in the event of a leak Leveling the washer Importance of leveling the washer Your new washer uses high spin speeds to remove water at the end of the wash cycle It is important that your washer is level and that all four washer feet press with equal pressure against the floor This will help assure the quietest most vibration free use of your washer Follow these steps 1 Install the washer on a level and solid surface preferably in a corner of a room 2 If the floor is uneven or unlevel adjust the washer feet as required to level the washer Do not place anything under the washer feet to help level the washer 3 Extend the washer feet no more than is necessary The more the feet are extended the more vibration the washer will experience Start with the washer feet turned all the way in and adjust each foot as necessary 4 Use a bubble level to check the top of the washer to make sure
17. water can dry e Always wait for the end of the cycle otherwise the appliance may still be locked If locked switch the appliance on and wait until it unlocks e lf at the end of the cycle the display is not lit up the energy saving mode is active To see display press any button Changing the volume You can set the volume by touching the Finish in button with the program selector in one of the following positions e Position 2 for indicator volume e Position 3 for button signals volume 4 AN 0 off 1 soft ee U 2 mid 3 loud Q 234 4 very loud Quit adjustment mode Turn the Cycle Selector to Off position The settings were saved Laundry Preparing the laundry Check the care labels on each laundry item prior to i washing Choose an appropriate wash cycle that does NOTICE Damage to the appliance fabrics not exceed the temperature recommended Foreign objects e g coins paper clips needles nails may damage the laundry or components in the washing Determining degree of soiling machine Therefore note the following tios when preparing your e Light soiling laundry No visible soiling or stains but may have absorbed some body odor This could include light weight summer clothing such as T shirts shirts or blouses worn for only one day Also to freshen bed linen or guest towels e Normal soiling Visible soiling and or a few light stains This could include clothing such as T shirts shirts
18. white spots on the washer drum caused by lime or mineral deposits or small amounts of rust caused by metal objects left in the drum NOTICE Descaling agents contain acids which may attack parts of the washing machine and may discolor the laundry 28 Cleaning the detergent dispenser tray If there is a buildup of residual detergent or additives or if the softener compartment is not rinsed out well enough it may be helpful to clean the dispenser 1 Open the detergent dispenser tray fully Press down on the drawer catch 1 and pull the tray 2 from the washer housing 2 Remove the insert 3 by grasping it and pulling it upwards from the detergent dispenser tray 3 Clean the insert and the detergent dispenser tray by holding it under warm running water Lightly wipe away any remaining detergent residue 4 Attach the insert and slide the detergent dispenser tray back into place and close the tray securely Tip Do not operate the washer without the detergent dispenser tray in place Always keep the tray completely closed Cleaning the water inlet strainers If the washer water supply slows or stops completely the water inlet strainer may be blocked Cleaning is recommended every 6 months in any event to reduce chances of valve blockage in areas using hard water Release the water under pressure in the supply hoses Normal water pressure in your home will cause some water to leak when you remove the water s
19. This can save you time make it easier to correctly install and use your washer and improve your overall satisfaction with your new appliance Special features e Load adjust matches the water and power consumption to each program according to the amount of laundry sensed in the drum and the type of fabric The load adjust function runs automatically to keep energy and water consumption as low as possible The water level sensor ensures the water level is correct for the laundry and the program selected e The automatic unbalanced load detection system spins the laundry several times to ensure even distribution If the laundry is not evenly distributed the spin speed is reduced or the laundry may not be spun for reasons of safety In the Wool program the spin cycle is attempted only twice in order to prevent felting Environmentally friendly use of your washer Your new Bosch washing machine is designed to use water energy and detergent in a highly efficient way to help reduce operating costs conserve resources and protect the environment e Utilize the maximum amount of laundry for the appropriate program e Avoid using too much detergent e Wash normally soiled laundry without a prewash e Save energy and detergent when washing lightly and normally soiled laundry e Energy saving mode The display panel lighting goes out after a few minutes and Start Pause flashes To activate the display touch any button Ener
20. actual spacing dimensions for min open area sizes G 3 in 7 6 cm H 14 in 35 6 cm NOTICES e Frozen hoses can tear or burst Do not install the washing machine outdoors or in an area exposed to freezing condtions e If the washing machine is located in a room which will be exposed to temperatures below freezing or if it is located in a cabin that is being shut down for the winter any residual water in the pump or water inlet hose s must be drained e Take care not to damage the washing machine Do not hold on to protruding parts e g door when lifting Do not push against the appliance door glass due to risk of damage e In addition to the safety information listed here the local water and electric authorities may have special requirements that must be followed e If in doubt have the appliance installed by an authorized technican e Hidden surfaces may have sharp edges During service use caution when reaching inside the washer housing These installation instructions are intended for use by qualified installers In addition to these instructions the installation must comply with for the United States National Electrical Code ANSI NFPA70 and latest editions of the State and municipal and or local regulations for Canada Canadian Electrical Code C22 1 and the latest editions of the Provincial Municipal and or local regulations Tools needed The following tools may be helpful during installation o
21. asher facing from front FG PIII IIE I The AquaShield hose prevents potential flooding in the event the hose develops an internal leak If the hose leaks the indicator turns red and water flow is blocked Once the internal valve in the hose activates indicator is red the hose must be discarded Contact customer service for a replacement Water drain hose connection NOTICES e Do not reuse an old drain hose Only use the drain hose and parts included with your washer e Do not kink or modify the water drain hose Height of drain point Height difference between the floor and drainage point max 39 in 100 cm Types of drainage hookups Standpipe Attach the drain hose to the elbow included with your washer Position the elbow on the drain hose 4 from end of hose as shown Insert this section of the drain hose into the drain pipe Secure the elbow and hose with a nylon tie strap or the equivalent to keep the hose from coming out of the drain pipe during use Sink siphon Secure the drain hose to the sink siphon using a 0 9 1 6 in 20 44 mm hose clip available from a hardware store Wash Basin WARNING SCALDING When washing at high temperatures there is a risk of scalding if you touch hot suds e g when pumping out hot suds into a wash basin Do not reach into the hot Suds NOTICE APPLIANCE DAMAGE DAMAGE TO TEXTILES If the end of the drain hose
22. ation for Third Party Accessories and Water Supply Hoses Third party accessories including water supply hoses other than those shipped with your Bosch washer and any consequential damages resulting therefrom are not covered by this warranty This limitation expressly includes the implied warranties of merchantability and fitness for a particular purpose which are also expressly excluded with respect to third party accessories including water supply hoses other than those shipped with your Bosch washer Use of third party accessories including water supply hoses other than those shipped with your Bosch washer does not void this warranty on any other part and all other provisions of this warranty remain in effect How Long the Warranty Lasts Bosch warrants that the Product is free from defects in materials and workmanship for a period of three hundred sixty five 365 days from the date of purchase The foregoing timeline begins to run upon the date of purchase and shall not be stalled tolled extended or suspended for any reason whatsoever This Product is also warranted to be free from cosmetic defects in material and workmanship such as scratches of stainless steel paint porcelain blemishes chips dents or other damage to the finish of the Product for a period of thirty 30 days from the date of purchase or closing date for new construction This cosmetic warranty excludes slight color variations due to inherent differences
23. can guarantee compliance with all current regulations Transporting the washer Before transporting the washer 1 Disconnect the washer power cord from the wall outlet Turn off the water supply to the washer Disconnect water supply lines from the tap Disconnect the drain hose from the drain location Install the transport bolt assemblies as shown in the following images oa Ba GW N Remove the transport bolt hole covers 1 Remove all four transport bolt hole covers 2 Pull the tio of the arrow on the cover out slightly to disengage the locking tab 3 Rotate the cover counterclockwise to remove Repeat for all 4 transport bolt hole covers Insert the transport bolt assemblies 1 Each assembly consists of a plastic bushing and a bolt that extends through the bushings Unscrew the bolt until the threaded end is flush with the end of the plastic bushing 2 Insert the transportation bolt and bushing assembly as Shown The metal housing slides around the bolt through the slot in the plastic bushing as the bushing is slid into place The open part of the bushing slot should be facing the direction shown to allow the assembly to slide fully into place 3 When the bolt is in place screw it in until the bolt threads engage the drum Double check and ensure bolts are screwed into threaded holes and not into cracks or crevices Repeat the process for all 4 transportation bolt assemblies before ti
24. ding to the Installation Instructions e all water drain power and grounding connections are in compliance with all local regulations and or other applicable regulations and requirements see the installation instructions in this manual for grounding requirements Electrical connection Page 16 A IMPORTANT SAFETY INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS WARNING WARNINGS FOR CHILDREN e Do not allow children to play on or in the appliance Close supervision of children is necessary when the appliance is used near children e Make sure to utilize all child lock safety features of your appliance and be sure to turn the appliance Off when not in use e Appliances are not intended for use by children however when children become old enough to operate the appliance it is the responsibility of the parents or legal guardians to ensure they are instructed in safe practices by qualified persons e Keep all laundry aids including detergents bleach fabric softener etc out of the reach of children Introduction to your new washer A WARNING RISK OF FIRE ELECTRIC SHOCK OR INJURY To reduce the risk of fire electric shock or injury to persons read the IMPORTANT SAFETY INSTRUCTIONS of this manual before installing or operating this appliance IMPORTANT SAFETY INSTRUCTIONS Page 6 Standard features and helpful information Thank you for choosing Bosch for your laundry appliance needs Please r
25. e old used hoses e The water supply hoses must not be kinked bent or pinched causing hose damage or restricting water flow e The water supply pressure must be between 14 5 to 145 psi 1 10 bar with a minimum of 2 2 U S gallons 8 liters of flow per minute A pressure regulator valve must be installed if tte maximum water pressure is exceeded e Make sure the water supply faucet is easily accessible when the washer is in use The faucet should be turned off if the washer is going to be unused for extended periods of time e Make sure rubber washers are in place at both ends of the water supply hose Missing washers could cause leaks e The connection points are under full water pressure Turn on the water tap and check for leaks e Periodically inspect the water supply hose and replace with a new hose if cuts kinks or leaks are observed CT FIERO o Water connection hoses e blue Cold water hose e red Hot water hose 13 Position hoses as shown when routing hoses to left side of washer facing from front FYLL EL LI LL Attach this end of the hose to the back of the washing machine as shown in the following pictures Be sure to x lt use clamps and route hoses as instructed Hand n tighten only I TI Position hoses as shown when routing hoses to right side of w
26. e too low Eliminate the cause E 93 Hot water tap not turned on Turn on the hot water tap Displayed at end of Supply hose for hot water kinked or Eliminate the cause replace the hose if damaged first cycle without hot pinched closed 0 Not pe IN Hot water pressure too low Eliminate the cause am i SAN a Strainer in water supply hose Connect both supply hoses hot and cold water for able Reset after sec clogged hot water appliances Water connections Page 13 ond cycle with hot water E32 Notafault the unbalanced load Distribute small and large items of laundry evenly in alternating display with detection system has interrupted the drum If necessary start an additional spin pro END when program is the spin cycle because the laundry gram finished is unevenly distributed E 18 Too much detergent used or non Use less detergent for future loads Only use HE deter HE detergent used displays at gents end of cycle Your washing machine is intended for Page 5 Pump is blocked obstructed Clean the washer drain hose and or the drain pipe May need to perform pump maintenance to clear blockage Cleaning the drain pump Page 29 Others Turn off machine wait 5 seconds and turn on again If the display shows again call customer service Customer service Contact the Customer Service department if your 1 800 944 2904 appliance needs repair Our representatives will be happy to provide details for an a
27. ead and follow the use amp care important safety instructions and troubleshooting information contained in this manual Please retain this manual for future reference Standard features e 17 7 lo 8 kg large drum capacity for regular cotton loads e Low washing and spinning noise levels e Large door opening featuring magnetic lock 1809 opening angle Quality tested Every Bosch washer is thoroughly tested before leaving the factory As a result a small amount of residual water may remain in the washer drum We recommend running the Drum Clean cycle to remove this water prior to washing your first load of laundry Before loading your first load of laundry Page 19 WARNING STATE OF CALIFORNIA PROPOSITION 65 WARNINGS This product contains chemicals known to the State of California to cause cancer birth defects or other reproductive harm SAVE THESE INSTRUCTIONS Keep These Instructions for Future Reference In case of change of ownership manual should be conveyed with the washer Web Site Visit our web site at www bosch home com us for more information and to view a selection of our products About this manual These operating and installation instructions may apply to more than one model of washer Illustrations used may show details that differ from your particular model Read your user manual It contains valuable information about safety installation and operation of your new appliance
28. ed on Oxygen like Sodium Percarbonate are safe to USE 1 Open the detergent dispenser tray 2 Add detergent or additive 3 Avoid overfilling tte compartment to prevent early dispensing 4 Close the detergent dispenser tray completely before starting the wash cycle Tip DO NOT operate the washer without the detergent compartment in place and fully closed Liquid detergent insert To measure liquid detergent 1 Pull out the detergent dispenser tray Press down on the insert and remove the drawer completely 2 Push the liquid detergent insert forward and down as shown 3 Reinsert the tray into its compartment NOTICE Do not use the liquid detergent insert with gel type detergents and powdered detergents or for cycles with pre wash and selected Finish in time Starting the cycle Touch the Start Pause button Indicator lamp lights up and the cycle starts NOTICE f you want to protect the cycle against inadvertent adjustment select the child lock Child lock Page 21 During the cycle the display field indicates the Finish at time and after starting the washing cycle the cycle duration and the symbols for the cycle progress Child lock You can secure the washer against inadvertent changing of the set functions To do this activate the child lock after cycle start To Activate Deactivate touch and hold Temperature and Finish in buttons for approximately 3 seconds The c symbol appears in
29. en us Use and Care Manual Installation Instructions 8 BOSCH OM FE F 4 gl s D ral in i ki V R LI i 1 j FR I hin i MO Bit GT CRETINO FE AE EH GE HE i wi i ul LI cul Washer WAT28401UC Welcome to Your New Washer Congratulations on your selection of a new Bosch washer for your laundry needs We are confident you will enjoy the superior performance and reliability Please do not hesitate to contact our Customer Service department if you have any questions or comments about your new washer Thank you for choosing Bosch Visit our web site at www bosch home com us for more information and to view a selection of our products Table of contents Important information ssservnnnvrnnnnnevnnnnevnnnnvnnnnnvevnnnueennn 4 Plen 4 TE en 4 Your washing machine is intended for 5 Importance and meaning of symbols 5 IMPORTANT SAFETY INSTRUCTIONS 6 Introduction to your new washer 7 Standard features and helpful information 7 opec TS NN ice 7 Environmentally friendly use of your washer 8 Dimensions and clearances required 8 Appliance dimensions ui 8 Length of power cord and water supply hoses 8 Installation types EE EE Er kreere rr rr 9 Installation instructions nrvanenanennnnnnnnnnennnnnnnvnnennnnnnn
30. ended in the user manual or in published user repair instructions that you understand and have the skills to carry out e Always Always unplug the washing machine from the power Supply before attempting any service Disconnect the power cord by grasping the plug not the cord Do not machine wash fiberglass materials Such as curtains and window coverings that use fiberglass materials Small particles may remain in the washing machine and stick to fabrics in subsequent wash loads causing skin irritation Do not install or store the washer where it will be exposed to the weather Hoses and internal parts may be damaged if exposed to freezing temperatures Do not use the washing machine if it has a worn power cord or loose plug The washing machine must only be used for its intended purpose follow the fabric care instructions recommended by the clothing manufacturer Make sure all water connections to the washing machine have shut off valves that are readily accessible during normal operation of the washer Turn off both valves during periods in which the washer is not in use and before leaving for extended periods such as vacations to reduce the risk of water damage in the event of a leak Turn the valves back on prior to resuming use of the washer Do not operate the washing machine if parts are missing or broken Do not operate the washing machine until you are sure that e the washing machine has been installed accor
31. er authority Soft water requires less detergent Too much detergent e Excessive foam will reduce washing agitation and cause poor washing and rinsing results e Not environmentally compatible wastes detergent and is not good for the environment Too little detergent e Laundry will not be washed clean e Eventually the laundry will take on a grey and hard appearance Greyish brown grease spots may stain the laundry heating elements may begin to calcify The fabric care label is important for selecting the correct detergent temperature and treatment of the laundry If desired you can visit the following sites for additional information on detergents and fabric care www textileaffairs com or www cleanright eu e Standard detergent with optical brighteners Suitable for white laundry made from linen or cotton Program Cottons Cold Extra hot e Detergent for colors without bleach or optical brighteners Suitable for colored laundry made from linen or cotton Program Cottons Cold Hot e Detergent for colors delicates without optical brighteners Suitable for colored laundry made from easy care and synthetic fabrics Program Easy Care Cold Hot 24 e Detergent for delicates Suitable for delicate fine fabrics silk or viscose Program Delicate Silk Cold Hot e Detergent for woolens Suitable for wool Wool program Cold Warm Saving energy and reduce detergent For light and normal soiling you can
32. f your washer e 13mm socket for removing the transport bolts e 1 mm wrench for adjusting the appliance feet e Bubble level for leveling the appliance Waste disposal Disposal of Packaging Materials After unpacking your new appliance dispose of the protective packaging materials in an environmentally friendly way Ask your dealer or inquire with your local authority regarding currently acceptable means of disposal A WARNING WARNINGS FOR CHILDREN Do not let children play with packaging and associated parts to avoid risk of choking or suffocation Disposal of Your Old Appliance Your old appliance can be recycled if it is no longer to be used Prior to disposing of your old appliance observe the following precautions to reduce safety risks A WARNING TO AVOID RISK OF INJURY OR DEATH DO THE FOLLOWING after unplugging the old appliance remove the electric power cord and dispose of properly remove the door or permanently disable the door lock to prevent children from being locked inside Parts provided with your washer Back side of the washing mashine Power cord with plug Literature pack contents e User manual e Warranty e Covers with hose holders Drain hose Elbow to form the hose to fit the drain pipe 11 Washer drum contents Two AquaShield water supply hoses are shipped in the washer drum Be sure to remove each of these items from the drum before using the washer
33. f the table below follow these steps 1 Turn the cycle selector to Off 2 Disconnect the washer from the power outlet 3 Turn off the water taps 4 Call Customer Service Customer service Page 4 NOTICE The troubleshooting items listed below can help you resolve minor issues with your washer quickly and without the necessity of waiting for a service call Service calls for issues that could have been solved by using this table may not be covered under the warranty Please rule out any of these issues before calling customer service 31 Determing the Problem Problem Washer door cannot be opened Door still cannot be opened even after turning the washer Off and back on again Wash cycle time is increased Cycle does not start Start Pause flashes Cycle does not start Finish in Time is dis played Cycle does not start c symbol flashes Detergent residue remains in the deter gent dispenser Water does not appear to be coming into the washer or detergent is not washed away Water cannot be seen in the drum 32 Possible cause s Child lock is activated A power failure occured Cycle is running or water level is too high and or too hot Electric power cord has become loose or unplugged Program selector turned to Off before end of cycle Emergency door lock released is activated Child lock is activated Door is locked for safety reasons high water level temperat
34. ghtening any all the way Complete tightening all 4 bolt assemblies until they are each snug in place 17 Getting to know your appliance Control panel Perm Press Off Cotton Normal Perm P Heavy Soil Cotton Light Soil Perm P Light Soil Towels Delicates Sanitize Quick 30 Jeans Rinse Spin _ Bulky Large Items Hand Wash Wool Drum Clean Drain Program Selector for selecting a program and on off switch turns in both directions Selectable temperature ranges Cold Warm Hot Extra Hot Temperature Finish in Spin Speed To change the default program settings Indicator lamp lights up if the setting is active Selectable Spin Speed ranges No Spin Low Med High Program status sequence e Wash amp e Rinse e Spin 6 4 Digit Display for settings and information e Finish time adjustable in 1h hour steps to 24 hours e program duration e g 2 40 hours minutes SpeedPerfect O Prewash FV Extra Rinse 2 Additional program settings Indicator on setting Is active 18 Wash Rinse Spin Speed Finish Extra Start Spin Perfect Temperature i Rinse PreWash Speed Pause Temp Cold Warm Hot Extl Hot Spin Speed No Spin Low Med High Start Pause Dl e starts or pauses the selected program e lit steady program running can be paused e blinking Options can be changed program can be started door is locked water may be hot program is in Pause mode Operating Instructio
35. gy saving mode is not activated if a program is running e If the laundry will be dried in a dryer afterwards select spin speed according to the dryer manufacturer s instruction Dimensions and clearances required Appliance dimensions Label Dimension U S Metric a width 23 6 in 60 cm b depth 25 in 64 cm to front of door C height minimum 33 2 In 85 cm height maximum 33 8 in 86 cm d side clearance 15 8 in 40 cm door open 180 e depth 42 5 in 108 cm door open 90 Weight approximate gross 164 Ibs 71 2 kg height of appliance depends on the extension of the height adjustable appliance feet Length of power cord and water supply hoses To left of washer To right of washer U S Metric U S Metric Electric power 25 in 64 cm 43 in 109 cm cord Water supply 43 in 109cm 28in 71 cm hoses Drain Hose 27 in 69cm 46 in 117 cm All distances are measured from indicated side when facing front of washer Installation types Stacked washer and dryer A Bosch dryer of the same dimensions can be placed on top of the washer to save space Use the special washer dryer stacking kits noted in Bosch Dryer User Manuals which can be purchased from customer service or your local dealer Clearance requirements Minimum A Both Sides 0 6 in B Top 6 3 In C Rear 2 5 in D Front 2 4 in Rear clearance as close to wall as venting or water 1 5 cm 16 cm 6 4 cm 6 1 cm connection
36. ild lock feature is activated you Must deactivate it before you can set a cycle Child lock Page 21 Use the cycle selector to select the desired cycle Turns in both directions The machine is switched on In the display field the cycle duration for the selected cycle appears and the indicator lamps for the pre set temperature and spin speed options light up Changing default cycle settings You can use the default settings or change them to your desired settings Touch the appropriate button until the desired setting IS displayed The settings or options are active when the related indicator is lit There is no need for additional confirmation on your part The settings or options are not retained after the appliance is switched off all are set back to default automatically Program selection table Page 25 Default Program and Option settings Page 27 Selecting additional cycle settings By selecting additional settings you can adjust the washing process to better suit the items you are washing The settings can be selected and deselected depending on the cycle progress The indicator lamps of the buttons light up if the setting is active The settings are not retained after the appliance is switched off Loading the laundry A WARNING To avoid risk of explosion Laundry items that have been pretreated with any material containing solvents e g stain remover cleaner s solvent must be rinsed ou
37. in painted and porcelain parts as well as differences caused by kitchen lighting product location or other similar factors This cosmetic warranty specifically excludes any display floor As Is or B stock appliances Repair Replace as Your Exclusive Remedy During this warranty period Bosch or one of its authorized service providers will repair your Product without charge to you subject to certain limitations stated herein if your Product proves to have been manufactured with a defect in materials or workmanship If reasonable attempts to repair the Product have been made without success then Bosch will replace your Product upgraded models may be available to you in Bosch s sole discretion for an additional charge All removed parts and components shall become the property of Bosch at its sole option All replaced and or repaired parts shall assume the identity of the original part for purposes of this warranty and this warranty shall not be extended with respect to such parts Bosch s sole liability and responsibility hereunder is to repair manufacturer defective Product only using a Bosch authorized service provider during normal business hours For safety and property damage concerns Bosch highly recommends that you do not attempt to repair the Product yourself or use an un authorized servicer Bosch will have no responsibility or liability for repairs or work performed by a non authorized servicer If you choose t
38. ind sand floods fires mud slides freezing temperatures excessive moisture or extended exposure to humidity lightning power surges structural failures surrounding the appliance and acts of God 36 In no event shall Bosch have any liability or responsibility whatsoever for damage to surrounding property including cabinetry floors ceilings and other structures or objects around the Product Also excluded from this warranty are Products on which the serial numbers have been altered defaced or removed service visits to teach you how to use the Product or visits where there is nothing wrong with the Product correction of installation problems you are solely responsible for any structure and setting for the Product including all electrical plumbing or other connecting facilities for proper foundation flooring and for any alterations including without limitation cabinetry walls floors shelving etc and resetting of breakers or fuses TO THE EXTENT ALLOWED BY LAW THIS WARRANTY SETS OUT YOUR EXCLUSIVE REMEDIES WITH RESPECT TO PRODUCT WHETHER THE CLAIM ARISES IN CONTRACT OR TORT INCLUDING STRICT LIABILITY OR NEGLIGENCE OR OTHERWISE THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED ANY WARRANTY IMPLIED BY LAW WHETHER FOR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE SHALL BE EFFECTIVE ONLY FOR THE PERIOD THAT THIS EXPRESS LIMITED WARRANTY IS EFFECTIVE IN NO EVENT WILL
39. ine washable textiles e Washing with common cold and hot maximum 140 F 60 C tap water and commercially available detergents and cleaning products suitable for use in washing machines e We recommend HE High Efficiency detergents because they are designed to deliver optimum performance from your front loading washer Not using HE detergent could cause problems such as oversudsing extended cycle periods or a decrease in wash performance NOTICE Do not use chlorine bleach Operating Instructions Page 19 e When measuring all detergents stain removers laundry care products be sure to follow the manufacturer s instructions e Children must not do any laundry without supervision e Keep pets away from the washer e Setup conditions Ambient temperature 32 104 F 0 40 C Relative humidity under 95 e Installation by qualified installers e Installation in accordance with all regulatory requirements if in doubt have the appliance installed by a specialist familiar with these requirements Read the use and set up instructions and all other information included with the washer and act accordingly Keep documents for future use Importance and meaning of symbols Important safety information is contained in this manual and on the warning labels located on your washer Standard symbols and headings are used to identify areas where you should take precautions to avoid Injury or damage Please take a m
40. ns A WARNING To reduce the risk of fire electric shock or injury to persons read the Important Safety Instructions and Operating Instructions before operating this appliance Before doing any laundry with your washing machine Check to make sure your washer has been installed properly by following the installation instructions in this manual Installation instructions Page 10 Check the machine Never connect the utilities power or water to or start a damaged machine Contact customer service Check to be sure your household electrical system voltage and the voltage specifications on the washing machine rating plate correspond Check to be sure the washer hot and cold water supply taps are turned on Turning the washing machine on and off The rotating Cycle Selector turns the washer on as wash cycles are selected and off when the selector is later turned to the vertical Off position Before loading your first load of laundry Your new washing machine was tested before leaving the factory This process involves running various wash cycles As a result a small amount of water may remain in the tub and drainage system Run a Drum Clean cycle with no laundry to clean the system before your first load of laundry First add 1 to 2 tablespoons of detergent to the main wash chamber Il Then run the Drum Clean cycle Wait for the cycle to finish Using the cycle selector to choose a wash cycle NOTICE If the ch
41. nsuring all safety precautions are followed when draining water from washer and or manually opening the washer door It may be necessary to clean the washer drain pump if the washer fails to drain sound of water being pumped from the washer cannot be heard when the washer should be draining and other nearby drains such as a sink are draining properly The washer pump can become blocked by loose debris a good reason to check the drum and remove any visible debris after each load Fabrics that give off large amounts of fluff may also cause blockage To access the washer drain pump the service cover must first be removed see steps below With the service cover removed proceed as follows 1 If the washer has not been drained try to drain it now Turn the program selector to the Drain and touch the Start Pause button Wait a few moments to let the cycle drain the water from the drum If the pump is totally blocked the water will be unable to drain and the cycle will end 2 Shut off the tap so that no more water flows in and has to be drained Switch the appliance off Unplug the power plug 29 3 Open and remove the service cover 5 Use the pull out drain hose located in the pump access opening to drain the remaining water into a suitable container up to 5 3 U S gallons 20 liters of water may be drained Pull the sealing cap from the hose and lay the hose over the side of the container and allow
42. o have someone other than an authorized service provider work on your Product THIS WARRANTY WILL AUTOMATICALLY BECOME NULL AND VOID Authorized service providers are those persons or companies that have been specially trained on Bosch products and who possess in Bosch s opinion a superior reputation for customer service and technical ability note that they are independent entities and are not agents partners affiliates or representatives of Bosch Notwithstanding the foregoing Bosch will not incur any liability or have responsibility for the Product if it is located in a remote area more than 100 miles from an authorized service provider or is in a reasonably inaccessible hazardous threatening or treacherous locale surroundings or environment in any such event if you request Bosch would still pay for labor and parts and ship the parts to the nearest authorized service provider but you would still be fully liable and responsible for any travel time or other special charges by the service company assuming they agree to make the service call SCOPE OF EXTENDED LIMITED WARRANTY Bosch will repair or replace free of charge any printed circuit boards drive motor or component part of the motor that proves defective under conditions of normal home use during the first seven hundred thirty 730 days from the date of purchase labor charges excluded Out of Warranty Product Bosch is under no obligation by law or otherwise to
43. oment to become familiar with each of these symbols and what they mean before proceeding A WARNING ELECTRICAL SHOCK HAZARD This indicates that death or serious injuries may occur as a result of non observance of this warning A CAUTION This indicates that minor or moderate injuries may occur as a result of non observance of this warning NOTICE This indicates that damage to the appliance or property may occur as a result of non observance of this warning Tip This symbol is used to draw the user s attention to important matters A IMPORTANT SAFETY INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS WARNING When properly cared for your new appliance has been designed to be safe and reliable Read all instructions carefully before use These precautions will reduce the risk of burns electric shock fire and injury to persons When using appliances basic safety precautions must be followed including those in the following pages Examine the appliance after unpacking it In the event of transport damage do not plug it in WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK SERIOUS INJURY OR DEATH WHEN USING YOUR WASHING MAGHINE FOLLOW BASIC PRECAUTIONS INCLUDING THE FOLLOWING e Bosch washers are provided with an Operating Care and Installation Instruction manual Read and understand all instructions before using the washing machine Do not wash articles that have been previously cleaned
44. onds Solutions are based on the specific reason the wash time has been extended Use less detergent Always load the washer with a mixture of large and small wash items easier to distribute in the drum Touch the Start Pause button to start the cycle Check if laundry is caught in the door Close the door until a click is heard the cycle should start Wash cycle will begin at proper time to complete at the selected finish time Deactivate Child lock touch and hold Temperature and Finish in for approximately 3 seconds Clean and dry the detergent dispenser See Adding the correct amount of HE detergent to determine proper detergent usage Clean and dry the detergent dispenser Select Start Pause Turn on water taps Eliminate the cause Clean the water inlet strainers Eliminate the cause No action needed Problem Water has not drained completely Water is coming out from underneath the washer Foam comes out of the detergent dispenser drawer The cyle status sequence Wash flashes in the display Repeated spinning No spin took place laundry is still wet Detergent residue on the laundry System shakes or shudders when spin speed increases Possible cause s Suds may be excessive usually due to too much detergent or non HE detergent being used Pump is blocked Drain hose or drain pipe is blocked Water supply hose is leaking is not screwed on tight at both ends
45. or rubber washer not placed in hose Drain hose is leaking Too much detergent was used or non HE detergent was used pump was not able to pump out the increased suds displays at end of cycle The Unbalanced Load Detection system is attempting to balance the load through repeated spins Load size too small Large items may have become entangled in the drum and could not be distributed by the Unbal anced Load Detection system spin cycle therefore canceled for safety reasons Excessive suds too much deter gent was used or a non HE deter gent was used amp displays at end of cycle No Spin was selected Some phosphate free detergents contain water insoluble ingredients that may appear as light spots on the laundry The washer drum suspension sys tem shifts during spinning as the speed increases This may result in a slight shaking of the washer during the spin speed transition Solution s Use less detergent for future loads Be sure to use only high efficiency HE detergents Check and clean the drain pump water drain hose and or the drain pipe Clean drainage pipe and or drainage hose Eliminate the cause tighten the hose by hand at the washer end check for rubber washer in place Check the drain hose be sure that it is on the washer securely with the clamp in place may need to replace the drain hose if leaking continues Immediate fix mix 1 tablespoon of fabric softener with 1 2
46. own prior to activating the emergency door lock release The drum may be full of hot water which could cause burn injury A WARNING RISK OF INJURY You may injure your hands if you reach into the drum while it is turning Do not reach into the drum when it is turning Wait until the drum has stopped turning A CAUTION WATER DAMAGE AND BURN INJURY Any escaping water may cause water damage and burns Do not open the washing machine door if water can be seen through the glass 1 Turn the washer off by rotating the cycle selector to the Off position Any running program will then be cancelled Disconnect the mains plug 2 Allow the water in the drum to cool off 3 Allow the washer drum to come to a stand still no longer spinning 4 Before opening the washer door perform the drain orocedure included in the pump maintenance section Cleaning the drain pump Page 29 5 Loosen screws and remove the protective foil 6 The washing machine door can then be opened Pull the emergency release downwards with a tool and release 7 The door can now be opened General Troubleshooting If you encounter a problem consider the suggestions and instructions below before you call customer service A WARNING ELECTRIC SHOCK HAZARD To avoid risk of electric shock repairs should be carried out by an authorized technician If repairs are necessary and you cannot eliminate the fault with the aid o
47. pecially gentle washing cycle to avoid shrinkage long cycle pauses clothing rests in suds and water Extra Rinse 1 is lit indicat ing cycle with one rinse anda spin Touch Extra Rinse but ton until no symbol is lit and cycle will be spin only no rinse 25 Programs Max Selectable program set Load tings upto default settings bold Temperature Spin speed Quick 30 1 2 Hot High approx 30 load Warm Med minute cycle Cold Low No spin Delicates 1 3 Hot Med load Warm Low Cold No spin Perm Press 1 2 Hot High Light Soil load warm Med Perm Press Cold Low Heavy Soil No spin Perm Press Tips Additional program settings Information Type of laundry Easy care fabrics made of cot ton linen synthetic fibers or blended fabrics suitable for lightly soiled laun dry For delicate washable fabrics e g made of cotton satin syn thetic fibres or blended fabrics e g Curtains bulky items e g comforters Cotton linen synthetic or blended fabrics SpeedPerfect Prewash Extra Rinse 1 2 SpeedPerfect Prewash Extra Rinse 1 2 Do not wash new multicolored laundry together with other laundry The cycles are time controlled for lightly soiled fabrics Rinse cycles use cold water only Starching NOTICE Laundry must not be treated with fabric softener Starching is possible in all wash programs if liquid starc is used Measure starch into compartment amp in accordance with the manufacturer
48. peed range depending on the cycle progress Touch the appropriate button until the desired setting IS displayed No Spin This option eliminates the final spin and the load remains saturated with the final rinse water The pump is activated to remove all residual water Program selection table Page 25 Finish in The program end Finished in time can be set in one hour increments to a maximum of 24 h hours After selecting the desired washing program at the dial but before touching the Start button touch the Finish in button until the desired time is displayed e g 8 h then touch the Start button to start the washer NOTICE The cycle duration is included in the set Finish in time Here is an example of a 2hr 30min cycle time and an 8 h Finish in time 8 his displayed until the Energy Saving mode activates and counts down approximately 5hr 30min until the washing cycle begins at 2hr 30min then the cycle duration 2 30 is displayed and began Total time approximately 8 hours Additional Program Option settings Extra Rinse 2 This feature is helpful for locations with very soft water or to generally improve rinsing results It allows up to 2 additional rinse cycles to be added to selected programs and will increase program time Prewash Pw For heavily soiled washing Pour 1 3 of normal detergent amount into pre wash chamber and remaining 2 3 into main wash chamber Il SpeedPerfect O For washing
49. r 10 MM OGG illa 10 TGOGIS Needed urina rain 11 Waste disposal 11 Parts provided with your washer mmmumsevvveeeers 11 Set up on a pedestal with drawer 12 BREIE ke de 12 Importance of installing on a solid level floor 12 Remove the transport DOS 12 Water connectionS siae ria 13 Leveling the washer mmmmmmeeevvvvvvvvvevrrrrrrrrrrrrn 15 Electrical Connection ri 16 Transporting the washer mmmmmmmeeeeeeerervvvvvvvvvvvevee 17 Getting to know your appliance 18 Control panel Luvensenesesmemsenetemetisainajeisnenn 18 Operating Instructions errrnnnnnnnvnnnnnnnnnnennnnnnnnnnvennnnnn 19 Before doing any laundry with your washing Machine 19 Before loading your first load of laundry 19 Using the cycle selector to choose a wash cycle 19 Changing default cycle settings n 19 selecting additional cycle Settings rrrsrrrrvvrrvrnnrrnnrrrrren 19 Loading the laundry mmmmmmeeeeveeeeeerrrrrrrrrrrn 19 Filling the detergent and additives compartments 20 Staring INE CONC EE 21 CIO ia 21 Selecting a different cycle nen ener rr rrrer 21 Pausing Adding a garment to the cycle 21 Cancel cycle ummm rrrveerervrvrmvrrrvveverrrrrrssrrrrreversrsrsnsssrrrvveessens 21 OVCE GNU see Er ERE FORENE 21 Removing laundry switching the appliance off 22 SION iii 22 ETG aS NE
50. rm Cold Extra hot Hot Warm Cold Extra Hot Hot Warm Cold High High Med Low No spin High Med Low No spin High Med Low No spin High Med Low No spin High Med Low No spin High Med Low No spin High Med Low No spin Type of laundry sturdy fabric cotton or linen fabric that withstands very hot water Half load or less of lightly soiled sturdy fabric cotton or linen fabric that withstands very hot water Durable cotton towels especially soft towels sturdy fabric cotton or linen fabric that withstands very hot water Dark cotton textiles and dark easy care textiles Wash textiles inside out Machine washable fabrics Stuffed with down such as pil lows and duvets also suitable for items stuffed with synthetic fibres Note Wash large items sepa rately Use a detergent designed for delicates and follow the instructions on the item s care label Use detergent sparingly Special cycle for cleaning the drum Hand and machine washable wool wool blend fabrics Extra rinse with spin Spin only with selectable speed Additional program settings Information SpeedPerfect Prewash Extra Rinse 1 2 Prewash Extra Rinse 1 2 SpeedPerfect Prewash Extra Rinse 1 2 SpeedPerfect Prewash Extra Rinse 1 2 longer wash and rinse with more water for especially sen sitive skin SpeedPerfect Prewash Extra Rinse 1 2 SpeedPerfect Extra Rinse 1 2 Es
51. rovide firm support This prevents the washer from experiencing excess vibration during spinning that could cause the washer to move or be noisy The installation surface must be solid and level in both directions Avoid installing your washer on soft surfaces such as floors with carpet or foam backed covering material If installing the washer on a wooden floor observe the following e install the washer in a corner for better support if possible e if necessary reinforce the floor by screwing a water resistant wooden board to the floor minimum of 1 18 in 30 mm thick Remove the transport bolts A CAUTION DAMAGE TO THE APPLIANCE OR INJURY POSSIBLE e The machine is secured for transport with transport bolts Transport bolts that are not removed can damage the drum during operation of the machine the washer will vibrate and it will be much noisier during spin cycles if the transport bolts are not removed before use Be sure to remove all 4 transport bolts completely before first use Keep the transport bolts If a pedestal was purchased with the washer it must be installed first prior to removing the transport bolts Please consult the pedestal installation instructions e In order to prevent transport damage during later transport be sure to re install the bolts before transport 1 Remove hoses from the brackets 2 Loosen and remove all 4 transport bolts Remove the sleeves Take the power cable o
52. rt Pause 2 Cool the laundry off Select Rinse 3 Touch Start Pause For cycles with a low temperature 1 Touch Start Pause 2 Select Drain 3 Touch Start Pause Cycle end End appears in the display field and the Start Pause button indicator lamp is off If this symbol appears in the display the washer has detected too much foam and it automatically adds an additional rinse to remove the foam NOTICE Use less detergent the next time you run the washer with the same load 21 Removing laundry switching the appliance off 1 Open the front door of the washer and remove the laundry 2 Turn the cycle selector to the Off position Appliance is switched off 3 Turn off the water tap NOTICES e Do not leave any laundry in the drum It can shrink or become discolored by the next laundry Signal You can change the following settings e volume for button signals e volume for indicator signals To change these settings always activate adjustment mode first Activate adjustment mode 1 Select Cotton Normal on Position 1 The appliance is on 2 Hold down Start Pause and turn the Program Selector to the right Position 2 Release Start Pause button Adjustment mode is now activated and the default volume for indicator signals appears in the display 22 e Remove any remaining items from the drum and rubber gasket e Leave the front door and detergent drawer open so that any remaining
53. save energy lower washing temperature and detergent Saving Reduced tem perature and Soiling note Light e g e Light summer sports clothing detergent worn for a few hours quantity as per the rec e T shirts shirts blouses worn ommended for up to one day dosage e Guest bed linen and hand towels used for one day No visible dirt or stains Clothing has taken on some body odor Normal e g e T Shirts shirts blouses sweat Temperature soaked worn a few times as per the e Towels bedding used for up care label and to one week detergent Visible dirt or a few light stains quantity as per the rec Heavy ommended Dirt and or stains clearly visible dosage for e g tea towels baby items work heavy soiling clothing NOTICE When measuring the amount of all detergents additives care products and cleaning agents please always check the manufacturer s instructions and information Program selection table Programs Cotton Normal Cotton Light Soil Towels Sanitize Jeans Bulky Large Items Drum Clean Drain Hand Wash Wool Rinse Spin Max Load up to full load 1 2 load 1 2 load full load 1 2 load 1 2 load 1 item empty full load 1 3 load full load Selectable program set tings default settings bold Temperature Spin speed Extra hot Hot Warm Cold Extra hot Hot Warm Cold Extra hot Hot Warm Cold Extra hot Hot Wa
54. suitable for the voltage specification shown on the washer rating plate located inside the washer door immediately below the drum opening Purchase information Page 4 see the table below for connection specfications and fuse breaker requirements Watts 2 880 max Hertz 60 Ampers 12 e The wiring for the electrical outlet circuit must be sufficient to meet the appliance requirements Use of a Ground Fault Circuit Interrupter GFCI is recommended e Protect the power cord from physical damage such as being twisted kinked pinched caught in a door or walked upon e lf the power cord is damaged it must be replaced by a qualified technician to avoid a fire shock hazard Replacement power cords can be purchased through Customer Service Customer service Page 4 e The washing machine must only be connected to an individual branch circuit via a socket which has been properly installed and grounded e Make sure that the power plug fits into the socket the wire size is sufficient the grounding system is properly installed e The power cord may be replaced by an electrican only Replacement power cords can be purchased from Customer Service To reduce the risk of fire or electrical shock DO NOT use an extension cord or an adapter to connect the washing machine to the power supply If a ground fault circuit breaker is to be used only use the types marked with the following symbol AA Only this symbol
55. t thoroughly by hand before they are placed in the washing machine Loosen the laundry being loaded and mix small and large items Unfold the sorted items and place them loosely in the drum Mix small and large items to help them better distribute in the drum during the spin cycle Tip Do not exceed the maximum load recommended for the type of wash Overloading will cause poor wash results and will cause wrinkles 19 Recommended Load Size Recommended maximum load size can be found Standard features and helpful information Page 7 a 1 3 Load woolens delicates silk b 1 2 Load cotton synthetic fabrics or knitted textiles c Full Load cotton and linen Filling A WARNING IRRITATION OF EYES SKIN When opening the detergent drawer during operation detergent or laundry care products may spray out Open the drawer carefully In case of contact with detergent or laundry care products rinse the eyes or skin thoroughly In case of accidental ingestion consult a doctor NOTICE To prevent build up and possible clogging of water ways dilute thick fabric softener or other laundry care products with water Pour the detergent and laundry care product into the appropriate chambers Tips After loading close the door carefully so as not to trap any items between the door and the rubber seal The door should close easily and should not be forced to close Foreign objects left in the drum ma
56. the display e lit steady The child lock is active e blinking The child lock is active and the cycle selector has been adjusted To prevent a cycle interruption set the cycle selector back to the initial cycle The symbol lights up again NOTICE The child lock can remain activated until the next cycle start even after switching the machine off Then you must deactivate the child lock before cycle start and if necessary activate it again after cycle start Selecting a different cycle If you have inadvertently started the wrong cycle You can change this as follows 1 Touch Start Pause 2 Select another cycle 3 Touch Start Pause The new cycle starts from the beginning Pausing Adding a garment to the cycle Pausing the wash cycle can be useful for several purposes e g for soaking Soaking Page 26 Touch Start Pause D appears on the display Wash load will soak in water until continued by touching Start Pause For adding a garment after the cycle begins 1 Touch Start Pause 2 Open door carefully and add or remove laundry item Note You can do this as long as the Start Pause indicator flashes and it is safe to do so 3 Close door 4 Touch Start Pause The cycle continues NOTICE If the cycle is paused but the door will not unlock it could be for safety reasons high water level water temperature or drum speed Cancel cycle For cycles with a high temperature 1 Touch Sta
57. upply hose from the back of the washer You can minimize this by first de pressurizing the hoses 1 Turn off the water tap 2 Turn the cycle selector to any wash cycle not to Drain or Spin 3 Touch Start Pause and allow 30 seconds to pass 4 Turn the cycle selector to the Off position This should reduce the water pressure on the water Supply hose Clean the strainers at the water tap end of the hose Fe a Ba ie de 1 Remove the hose from the tap 2 Rinse the strainer under running water Look at the strainer to see if any visible debris is still present Rinse again if necessary to remove the debris 3 Reconnect the hose to the tap Clean the strainers at the washer end of the hose 1 Remove the hose from the inlet on the back of the washer 2 Using narrow pliers grasp and pull the strainer from the inlet port 3 Rinse the strainer under running water 4 Reconnect the hose to the back of the washer and turn on the water tap Check to see if water flows by starting a warm water wash cycle NOTICE Check for leaks to be sure the rubber washers are seated at both ends of the water supply hose and the connections are properly tightened Cleaning the drain pump A WARNING RISK OF SCALDING Risk of hot water injury to skin Allow the water to cool down prior to actuating the emergency door lock release You are responsible for e
58. ure of water hot or high drum speed drum is turning Your washer utilizes sensors to monitor certain characteristics of the wash load Increases in wash cycle time could be due to Excess suds displays at end of cycle The automatic unbalanced load detection system spins the laundry several times to ensure even distri bution Start Pause button not touched selected Washer door is not closed properly Cycle ending time has been selected and activated Child lock is activated Dry detergent may have been damp or lumpy Excess liquid detergent may have been added Use the dosing cup for liquid deter gent when dosing powder deter gent Powder detergent may have been damp or lumpy Start Pause selected Water taps not turned on Supply hose kinked or pinched reduce flow Water supply hose strainers clogged Water pressure too low The water level in your high effi ciencey front load washer is below the visible part of the drum this is normal Solution s Deactivated Child lock touch and hold Temperature and Finish in for approximately 3 seconds If a cycle is interrupted by a power failure it will resume when the power is restored Wait until the cycle ends Make sure the electric cord is securely plugged in Turn the program selector to a cycle Emergency door lock release Page 31 Deactivated Child lock touch and hold Temperature and Finish in for approximately 3 sec
59. ut of the brackets 3 Place covers over the transport bolt holes Four plastic covers are provided in the small parts bag included with your washer Separate these covers and install one in each hole where the transport bolts were removed Lock covers firmly by pressing on the snap hook Insert hose holder Secure hoses in the hose holders NOTICE Keep the assemblies together and store them for later use such as when moving the washer Water connections Water supply hose connections NOTICES e The washing machine must only be operated with cold and hot max 140 F 60 C tap water Do not connect the appliance to the mixer tap of a pressurized hot water boiler e To prevent water damage the hot and cold water valves should be accessible when the washing machine is in place and should always be turned off when the washing machine is not in use e If installing the washing machine in a new building or a building in which the plumbing system was recently installed or upgraded flush the lines before installing the washing machine to remove any sand dirt or residue e To prevent leakage or water damage follow the instructions in this chapter e If in doubt have the appliance installed by an authorized technician Connect your washer to the wall faucets using the included AquaShield water supply hose Observe each of the following e Only use the new water supply hose shipped with your washer Never us
60. uthorized service www bosch home com rovider close to you re and FD cu be 1901 Main Street Suite 600 Irvine CA 92614 When you contact Customer Service please have the E Nr model number and the FD serial number for your appliance available You can find the identification plate with these numbers on this information on inside of the appliance door or on the back of the appliance Questions Please contact us We look forward to hearing from you 34 STATEMENT OF LIMITED PRODUCT WARRANTY What this Warranty Covers amp Who it Applies to The limited warranty provided by BSH Home Appliances Bosch in this Statement of Limited Product Warranty applies only to the Bosch appliance sold to you the first using purchaser provided that the Product was purchased e For your normal household non commercial use and has in fact at all times only been used for normal household purposes e New at retail not a display as is or previously returned model and not for resale or commercial USE e Within the United States or Canada and has at all times remained within the country of original purchase The warranties stated herein apply only to the first purchaser of the Product and are not transferable Please make sure to return your registration card while not necessary to effectuate warranty coverage it is the best way for Bosch to notify you in the unlikely event of a safety notice or product recall Limit
61. will allow If the washer is installed with a dryer the greater rear clearance for the dryer venting is required for the laundry pair Ventilation area Minimum E Top 63 sq In F Bottom 63 sq in 404 sa cm 404 sq cm Vent spacing actual not minimum dimensions G 37 in H 26 in J 3 in K 29 in 94 cm 66 cm 7 6 cm 73 cm Stand alone shown or Side by Side Under counter Preferred Front of the appliance fully open No doors or coverings Minimum opening dimensions A 28 In 71 1 cm B 23 8 in 60 5 cm C 35 5 in 90 2 cm Under counter Less Desirable Installation instructions amp WARNING RISK OF FIRE ELECTIRICAL SHOCK OR INJURY TO PERSONS To reduce the risk of fire electric shock or injury to persons read the Important Safety Instructions at the front of this manual before installing or operating this appliance A CAUTION WASHING MACHINE IS HEAVY Use additional helo and care when lifting and positioning Introduction Read these installation instructions completely and carefully before starting to install your new washing machine The information contained can save you time and effort and will help to ensure optimum performance of your new washer Be sure to observe all warnings and cautions If front of the appliance is covered ventilation openings must be installed E amp F are minimum area sizes E 63 sa in F 63 sa in 404 sq cm 404 sq cm G amp H
62. y damage laundry Before inserting any laundry check to make sure no foreign objects are in the drum Filling the detergent and additives compartments NOTICE Damage to the appliance Detergent and laundry pre treatment aids e g spot remover pre wash sprays etc can cause damage if they come into contact with the surfaces of the washer Do not let these substances touch the surfaces of the washer If necessary wipe off spray traces and other traces drops immediately with a soft cloth Measuring Measure out the detergent and laundry care products according to e the water hardness consult your water utility company for details e the manufacturer s instructions on the packaging e quantity of laundry e amount of soiling heavy normal light 20 Liquid deter for liquid detergent gent insert A Pre wash Detergent for pre wash chamber Softener Fabric softener starch chamber amp Do not exceed max Tips Do not pour fabric softener directly into the wash load Fabric softener is automatically dis pensed during the last rinse cycle Dilute concentrated or thick fabric soft ener or fabric conditioner with water 2 3 s water before pouring it into the dis penser prevents blockage of overflow Main wash Detergent for main wash water softener chamber Il spot remover NOTICE Do not use Chlorine based or color safe bleaches as these could damage the washer Detergents and or solid bleaching agents bas

en-us Use and Care Manual, Installation Instructions Washer

Contents

Download Pdf Manuals

Related Search

Related Contents