iOSD (On Screen Display) User Manual
Contents
1. 6S then Output Voltage 11 2V Make sure you camera is rated for this voltage and current 1A if not please use a separate battery supply If you use other wireless video transmitter and the rated voltage is over the voltage of BATT you can use the POWER pin to apply power Make sure the total current consumption of wireless video transmitter and camera is lower than 1A otherwise will damage your iOSD Aircraft End Ground End 2012 DJI Innovations All Rights Reserved 6 Display Description The iOSD information is displayed on the screen as shown below NO Function 1 Power voltage 2 Channel Distance between 3 aircraft and home points 4 Height 5 Control mode 6 Fail safe mode Display B Dbiink CH1 CH2 CH8 o TH ATT M GPS FS APT GHome 2012 DJI Innovations All Rights Reserved Description The aircraft power battery voltage in real time unit in V Its value is the same as the protection voltage set in the assistant software blink first level low voltage alert Wireless video transmitter channel selection When the home point is successfully recorded this item will show unit in m The vertical height between the aircraft and the take off point unit in m The autopilot system control mode ATT is Atti mode GPS is GPS Atti mode M is Manual mode FS is in Fail safe mode2. to the IOSD switch port Position 1 gt Position 2 hold position 2 for 1 5s every toggle from Position 1 to Position 2 increases the channel of the wireless video transmitter module by 1 from CH1 to CH8 only for the wireless video transmitter module specified by DJI Position 3 gt Position 2 hold position 2 for 1 5s toggle the switch to select the required video input when there are two video inputs Only the toggle from Position 3 to Position 2 can change the video input source Position 2 Position 3 2012 DJI Innovations All Rights Reserved 5 Video Output Port e If you use wireless video transmission module AVL58 specified by DJI connect through the bi port cable e f you use your own module please connect through the one port cable according the pin description Channel Control pin Control signal for the video transmitter channel number CH1 CH8 If your video transmitter does not support this feature then ignore this pin Video and OSD output pin make sure this is correctly connected Positive Negative voltage of battery pin its output voltage is equate to the voltage of the battery supplying power for your wireless video transmitter It is recommended to solder the two cables of the same function Please make sure the input voltage of your own wireless video transmitter is matched to the voltage of BATT to prevent damage from your wireless video transmitter module For example if
3. APT is in ground station mode GHome is in go home status 10 11 12 13 Pitch attitude P 0 Roll attitude R 0 Flight velocity 0 0m s GPS satellite gt 0 Video input AV1 AV2 Aircraft nose O 4p direction S Vertical velocity 0 0 x 2012 DJI Innovations All Rights Reserved Positive value means the aircraft nose is up negative value means the aircraft nose is down Positive value means the aircraft is right Negative value means the aircraft is left The aircraft horizontal speed Number of GPS satellites acquired Video input source selected AV1 or AV2 can be chosen Display the relative angle between aircraft nose and home point The aircraft nose is pointing to the home point when the icon Vis in the middle of the screen this may help you to bring back the aircraft by distinguishing the aircraft nose direction For example when the icon on your display screen is located in the Orientation 3 as shown in the following figure you can change the aircraft nose direction through operating your R C TX When the icon arrives at the Orientation 1 your aircraft nose is heading the home point which can help you pull your aircraft back to the home point easily i Orientation 4 Orientation 5 Aircraft i Orientation 3 A gt M Orientation 2 ilOrientation 1 Aircraft nose direction ote Home point o gt o 90 Orientation 3 Orientation 1 Orientation 2 135 4 Upward speed Down
4. Cable x1 Connect the iOSD with video input source i e camera or DJI 215 for video input and power supply with maximum current of 1A If you connect the iOSD to DJI Z15 please use the 4Pin Audio Head cable If connect to other camera use the 4Pin cable for the connection in accordance with the wiring diagram Video Output Cable x2 Only when you use the wireless video transmitter module specified by DJI you can use the bi port cable to connect the iOSD with the video transmitter module T Otherwise you can use the one port cable for your own connection in accordance with the wiring diagram 2 PIN to 3 PIN Cable x1 Connect the iOSD with the R C receiver through this cable When there are two video signal inputs it is used for the selection of video signal sources It can be used for the selection of AVL58 video channel 2012 DJI Innovations All Rights Reserved 4 Assembly STEP1 Fix the iOSD controller on your aircraft STEP2 Connect the iOSD with the video signal source wireless video TX module DJI autopilot system and R C receiver Make sure the connection is correct in accordance with the wiring diagram STEPS Setup a 3 position switch on the R C TX as the iOSD control switch STEP4 Connect your wireless video RX module with the display screen 3 Position Switch Control Choose a 3 position switch and make sure you connect the correct channel of the receiver
5. IOSD On Screen Display User Manual V2 00 2013 01 30 www dji innovations com 2012 DJI Innovations All Rights Reserved Disclaimer Thank you for purchasing product s from DJI Innovations Please read the instructions carefully before installing the hardware and software for this product this will ensure trouble free operation of your iOSD Please use DJI products in accordance with the provisions of your local authorities and regulations As DJI Innovations has no control over use setup final assembly modification including use of non specified DJI parts i e motors ESCs propellers etc or misuse no liability shall be assumed nor accepted for any resulting damage or injury By the act of use setup or assembly the user accepts all resulting liability DJI Innovations accepts no liability for damage s or injured incurred directly or indirectly from the use of this product DJI and iOSD is a registered trademark of DJI Innovations Names of products brands etc appearing in this manual are trademarks or registered trademarks of their respective owner companies This product and manual are copyrighted by DJI Innovations with all rights reserved No part of this product or manual shall be reproduced in any form without the prior written consent or authorization of DJI Innovations No patent liability is assumed with respect to the use of the product or information contained herein Contents DJS CAV AE EEE O E T E T T
6. Input Port for wireless video module channel selection and video input source selection Video Signal Output Port AV OUT Video Signal Output including both video and iOSD information AV GND Video Signal Ground UART transmit the wireless channel control signal to the wireless video transmitter For example AVL58 BATT it is equate to the Positive Voltage of Battery BATT it is equate to the Negative Voltage of Battery Video Input Port 2 input sources are available and the default setup is AV1 yYe Micro AV1 Video Input Source 1 AV2 Video Input Source 2 POWER 11 13V supply power for video input source with the maximum current of 1A GND Ground USB Port Connects the iOSD with PC for firmware upgrade cf CAN Bus Communication of the iOSD with autopilot system through CAN Bus LED LED indicator for power 2012 DJI Innovations All Rights Reserved 13 Specifications Performance Parameter Video Input Mode Video Output Mode Physical Temperature V1 0 Mark II Size Weight V1 0 Mark II Hardware Supported Voltage Current Typical Value V1 0 Mark II Rated Power Controller Supported Software Supported Built in Functions PAL NTSC PAL NTSC 20 70 C 20 60 C 52mm X 41mm X 11mm 42g 56 g 3S 6S LiPos 51mMA 25 2V 87MA 12 6V 60MA 25 2V 108mMA 12 6V 1 25W WKM IOSD Information Transmission Video Transmission 2 Video Signal input Channels Swi
7. Please follow the procedure for firmware upgrade otherwise the iOSD might not work properly 9 Make sure your computer is connected to the Internet Please close all the other applications during the firmware upgrade including anti virus software and firewall Make sure the power supply is securely connected DO NOT un plug the power supply until firmware upgrade has finished Connect the iOSD to PC with Micro USB cable DO NOT break connection until firmware upgrade is finished Run the assistant software and wait for connection Select Info gt Software and Firmware DJI server will check your current software and firmware version and get the latest software and firmware prepared for the unit If there is a software version more up to date than your current version you will be able to click to download the new version Please re install the assistant software follow the prompts If there is a firmware version more up to date than your current version you will be able to click to update them Wait until Assistant software shows finished 10 Click OK and power cycle Your unit is now up to date Note If firmware upgrade failed the iOSD will enter waiting for firmware upgrade status automatically please try again with the above procedures 2012 DJI Innovations All Rights Reserved 12 Appendix Port Description BATT Power Battery Input Port input voltage range 11V 26V 7 PORT Control Signal
8. and both of them are power on and then switch on the transmitter first Run the iOSD Assistant Software If the Data Communication Indicator is Red on please double check the connections and driver installation otherwise if the indicator is blinking Green go to next step Select the Main item to adjust the display position of the iOSD information if necessary And then configure the warning of GPS Satellite Number Distance and Height Range if warnings are required Click the DataView item and follow the tips to get the flight attitude data main control input and output information etc Note lf you do not configure the Warnings Setting the IOSD will show warnings in default values t will auto detect the firmware version when you open the assistant software and prompt the check for updates window if your version is not the latest one If enter the Data View mode the iOSD controller will temporarily quit the parameter configuration mode and act as a USB Device to connect to the PC You can manually select and read any data file from the USB Device If you need to re enter the parameter configuration mode please power cycle the iOSD The speed of data loading will be very slow for large files For the large file on the iOSD controller please copy the file to the local hard drives of the PC and then open the file for viewing 2012 DJI Innovations All Rights Reserved 11 Firmware amp Assistant Software Upgrade
9. apter versions including SAO and SAO for 215 If the iOSD is working with the 215 please use the version of SAO for Z15 otherwise if with your camera use the SAO Please connect the adapter according to the below figure Using the SAO AV Input1 Power Cameral Ground AV Input2 Power Camera2 Ground iOSD JEL for Z15 2012 DJI Innovations All Rights Reserved DJI Z15 GCU 16
10. er installer and assistant software from the iOSD page of DJI website Connect the iOSD Controller and the PC via USB cable power on the iOSD Controller system Run driver installer and follow the instructions strictly to finish installation Run assistant software installer and follow the instructions strictly to finish installation Assistant Software GUI osD ON SCREEN DISPLAY English w iOSD Setting Data View Software Version amp Firmware Version Adjust etc C Left C Right Text Indication iOSD Setting is used for adjusting the display position of the iOSD Main T ATOT TET well so thatthe iOSD information can Please refer to the real device display show on the monitor screen completely Warnings Setting Also you can sel GPs Height an arnings Setting ere ee Distance warning threshold Sat Number 0 Distance 0 m ata Communication i indicator Learn more Height Range Om Default PC Connection Indicator 2012 DJI Innovations All Rights Reserved 10 Assistant Software Usage Using the assistant software adjust the display position of the iOSD information upgrade the firmware and assistant software are available In addition the flight data will automatically be saved as files in the IOSD which can be viewed by connecting to the PC Power on your computer Make sure to power on iOSD Connect the iOSD Controller to the PC with a USB cable If the iOSD is connected to the autopilot system
11. sans ee sasana caine santo S T E E T T E 2 COMENS esene a a E E E E E EEE E E EEE 2 NATHOCUICHO ia PREE AA PEE AE E E E T E E A EE E ee ee oe 3 DAES 5 a a ae art a a acc ge E T ar ET E E E E E 4 PRS AWN EEE E ETE EEE TEE EAE EA E 5 DS PAY DESCHID Mioi an a N N NONN 7 WOSL aana A a Aa E N a A A ETA 9 PSSIStANL SONNIE i E E S 10 Software and Driver Installation ivi scssiscie tees ieeetece cree dvnnecdetets eve tinedetedeieee tots ieveteeniianaededetaaseceees 10 Assistant Sonware Gu hci a cccttsct ereeichaccsiheneebaenkencoenw tena ae bea ear 10 ASSISTANT SONWARC IIS AUG a A A as vigor as E S AE 11 Firmware amp Assistant Software Upgrade ccccccccseeeeeeeeeeeaeeeeeeeeeeaeeeeeeeeeeeaeaceeeeeessaaeeeeeeesaaaneeees 12 PAO iS D ETE E T A AE T rian onic T A ia as agua an ad ie aed isda eased estes A T O 13 POM DOSCHDUON sieccsescontcsesvwnteieietosesnetneedepetatedenet eecunon a a 13 SVCCIICANONG seina teh ae ea eee 14 rouble SNOG eceemee epee aren E A repr Reem er nay ona err mare Creer ar mere ern tare are mere cm a 15 Some Descriptions for the Version 0 ccccccsseeeeeeeeeeeeeeeeeeeeeesaeeeeeeeessaaaeeeeeeesaaceeeeeesseaeeeeseeees 16 2012 DJI Innovations All Rights Reserved 2 Introduction DJI iOSD is specially designed for DJI autopilot system during the FPV flight or other aero modeling activates DJI iOSD can transmit video and iOSD information in real time which will help you to obtain the aircraft status information d
12. tchable Remote channel selection of the Wireless Video Transmitter Module when using the video transmitter specified by DJI Built in BEC improve the reliability of power supply for the main controller DJI Z15 Supported 2012 DJI Innovations All Rights Reserved 14 Trouble Shooting No What Only iOSD information video signal loss Only video signal iOSD information loss Both video signal and iOSD information loss Both video signal and iOSD information loss Why Video input error Connection between iOSD controller and autopilot system error Signal transmission error The video signal cable to display screen is unconnected or short circuit 2012 DJI Innovations All Rights Reserved How to Make sure the connection between iOSD controller and video input port is OK Make sure the connection between iOSD controller and DJI autopilot system is OK Make sure the Wireless Video Transmitter Channel Setting is correct Make sure the communication between the video transmitter and the receiver is working correctly Make sure the connection of video signal cable is OK 15 Some Descriptions for the Version1 0 There is an adapter for the Version1 0 to solve the problem that the iOSD is incompatible with your camera If there is the incompatible problem with your device please contact your authorized dealer to get an adapter for free There are two ad
13. the Battery is 6S 25V and the input voltage of the wireless video transmitter is 3S 12V then you cannot use the BATT to supply power since the 25V is larger than 12V Wireless Video Transmitter Specified by DJI AVL58 Negative voltage of battery BATT Positive voltage of battery BATT O AO CLED SAD Channel Control Video GND UUUUOUUU Video and OSD output 3 position switch R C Receiver EE m o A9Z ALL Liva iOSD ON SCREEN DISPLAY EPT PMU DJI Autopilot System Video Input Port If you use the DJI Z15 it is recommended to use the 4Pin Audio Head cable for connecting the iOSD and GCU If you use the 4Pin cable please connect the iOSD to the Z15 s GCU according to the above chart If you use your own camera s please connect through the Video Input Cable according the pin description AV1 AV2 pin you can select the required input AV1 is default POWER pin supply power for Video input source such as a camera with the maximum current of 1A If the battery is 3S Lipo then Output Voltage Input Votage If 4S
14. uring a FPV flight It can display power voltage flight velocity height distance from the home point horizontal attitude GPS satellite number etc iOSD and video information are superposed on the receiver making iOSD data clearly visible and bringing you a more involved flight experience DJI iOSD should be used in conjunction with a DJI autopilot system It supports two video input sources under PAL or NTSC mode which can be selected remotely by an R C transmitter switch The R C TX switch can also change the wireless video transmitter channel remotely when user uses the wireless video transmitter specified by DJI The iOSD supports online upgrades The iOSD is built in BEC which is on the one hand for the power supply of the camera on the other hand for the power supply of the autopilot system s main controller to improve the power supply reliability of the main controller Specified autopilot systems for the iOSD Supported WKM Not yet supported WKH ACE ONE ACE WAYPOINT 2012 DJI Innovations All Rights Reserved 3 In Box IOSD Controller x1 Connect the iOSD controller to your DJI autopilot system via CAN Bus It communicates with the main controller receives data from the main controller superimposes the data with the video image and then transmits the whole information via a transmitter CAN Bus Cable x2 Connect the iOSD to your autopilot system through a CAN Bus cable Video Input
15. ward speed Use attitude line for aircraft attitude observation craft up ERNA craft down e e o V oer CY 6 L 6 VY U 14 Attitude line ee craft left eee d n e craft right M Display the 3 axis attitude of the gimbal when a 5 gimbal is used 15 Gimbal Attitude 0 0 5 Roll Direction 0 Pitch Direction 0 Yaw Direction Test Please use the following procedures to test your installation in order to make sure the iOSD is working properly STEP1 Ensure batteries are fully charged for R C transmitter iOSD and all the other devices on your aircraft STEP2 Make sure all connections and wiring is correct and secure STEP3 Make sure the communication between the wireless video RX and TX modules is normal STEP4 Switch on the R C transmitter and power on the iOSD and autopilot system STEP5 Check the LED indicator on the iOSD The iOSD is powered when the LED is on STEP6 If there are two video inputs please select an input by toggling the TX 3 position switch otherwise please skip to the next step STEP7 If you use the wireless video RX and TX modules specified by DJI please select the channel you require by toggling the TX 3 position switch otherwise please skip to next step STEP8 Observe the display screen to make sure the video and iOSD information are displaying on the screen 2012 DJI Innovations All Rights Reserved 9 Assistant Software Software and Driver Installation Please download driv
Download Pdf Manuals
Related Search