USER MANUAL
Contents
1. DATA 0 The PC sends this instruction to the machine The machine replies by sending back a value relating to the current video format INSTRUCTION 10 WRITE EEPROM DATA DATA EEPROM sub address EXTENDED DATA data to be written to this sub address The PC sends data directly to the EEPROM The EEPROM stores this new value and replies by sending the same data back to the PC CAUTION this function was designated for development and testing purposes Improper use of this function may cause erratic behaviour of the machine INSTRUCTION 11 READ EEPROM DATA For sending to machine DATA EEPROM sub address When replying DATA EEPROM sub address EXTENDED DATA requested data The PC sends this instruction to the machine The machine replies by sending back the data of this sub address INSTRUCTION 12 WRITE PC DATA PC sub address EXTENDED DATA data to be written to this sub address The PC sends PC data to the I C address which was last accessed via INSTRUCTION 13 The machine replies by sending the same data back to the PC CAUTION this function was designated for development and testing purposes Improper use of this function may cause erratic behavior of the machine INSTRUCTION 13 READ PC For sending to machine DATA PC address EXTENDED DATA sub address When replying DATA sub address EXTENDED DATA data read The PC sends this instruction to the machine The machine replies by sending back the data2. of this address and sub address INSTRUCTION 16 ERROR If the machine receives an invalid instruction it replies by sending this error code INSTRUCTION 57 ENABLE POWER DOWN SAVE DATA 0 disables power down saving DATA 1 enables saving EXTENDED DATA set to 0 The PC sends this instruction to the machine The power down option is enabled or disabled according to the value of DATA If the power down option is enabled then the machine will remember its state before being turned off and revert to this state when turned on again Note that whenever the machine is turned on the power down save option is enabled INSTRUCTION 61 IDENTIFY MACHINE For sending DATA 1 to request machine name DATA 3 to request software version number EXTENDED DATA set to 0 The PC sends this instruction to the machine The machine relies as follows if the machine name is requested the machine replies with DATA 75 hex and EXTENDED DATA 01 hex if the software version is requested the machine replies with DATA as the version number before the decimal point and EXTENDED DATA is the value following the decimal point For example for version 3 4 the machine replies with DATA 03 hex and EXTENDED DATA 04 hex 8 KRAMER SIMPLE CREATIVE TECHNOLOGY LIMITED WARRANTY Kramer Electronics hereafter Kramer warrants this product free from defects in material and workmanship under the following terms HOW LONG IS TH
3. E WARRANTY Labor and parts are warranted for three years from the date of the first customer purchase WHO IS PROTECTED Only the first purchase customer may enforce this warranty WHAT IS COVERED AND WHAT IS NOT COVERED Except as below this warranty covers all defects in material or workmanship in this product The following are not covered by the warranty 1 Any product which is not distributed by Kramer or which is not purchased from an authorized Kramer dealer If you are uncertain as to whether a dealer is authorized please contact Kramer at one of the agents listed in the web site www kramerelectronics com Any product on which the serial number has been defaced modified or removed Damage deterioration or malfunction resulting from i Accident misuse abuse neglect fire water lightning or other acts of nature ii Product modification or failure to follow instructions supplied with the product iii Repair or attempted repair by anyone not authorized by Kramer iv Any shipment of the product claims must be presented to the carrier v Removal or installation of the product vi Any other cause which does not relate to a product defect vii Cartons equipment enclosures cables or accessories used in conjunction with the product WHAT WE WILL PAY FOR AND WHAT WE WILL NOT PAY FOR We will pay labor and material expenses for covered items We will not pay for the following 1 Removal or installations charges 2 Costs
4. ES Power supply Null modem adapter mounting bracket 1 Specifications are subject to change without notice 6 KRAMER SIMPLE CREATIVE TECHNOLOGY Communication Protocol 7 Communication Protocol RS 232 communication with the 7508 complies with the following protocol The protocol uses 4 bytes of information and data is at 9600 baud with no parity 8 data bits and 1 stop bit Table 4 Structure of the Protocol MSB LSB INSTRUCTION 0 TO PC 15 14 B 2 IL 10 7 6 5 4 3 2 1 0 Ist byte DATA 1 D6 D5 D4 D3 D2 DI DO 7 6 3 4 3 2 1 0 2nd byte EXTENDED DATA 1 E6 E5 E4 E3 E2 El EO 7 6 5 4 3 2 1 0 3rd byte MSB s ADDR 1 E7 D7 0 0 1 1 0 7 6 5 4 3 2 1 0 4th byte Note that the MSB s of the DATA D7 and the EXTENDED DATA E7 are in the fourth byte Terminology TO PC is the DESTINATION BIT 14 10 is the INSTRUCTION D7 D0 E7 E0 is the DATA is the EXTENDED DATA AO is the LSB of the MACHINE ADDRESS The destination bit TO PC is 0 when sending from the PC to the machine or 1 when sending from the machine to the PC Table 5 Instruction Set for the 7508 INSTRUCTION Bb KM Bi PR 0 0 Reset 0 0 0 0j 0j 0 1 Read video standard 0 0 0 00 1 3 Read back panel DIP switch 1 video format CV YC 0 0 O Aia 1 10 Write EEPROM data low address 0 0 1 0 1 0 11 Re
5. Kramer Electronics Ltd af KRAMER USER MANUAL Model 7508 CV YC to SDI Converter Contents Contents Introduction Getting Started Overview Your 7508 CV YC to SDI Converter Using Your 7508 CV YC to SDI Converter Connecting a PC Setting the Dipswitches Technical Specifications Communication Protocol Noe Figures Figure 1 7508 CV YC to SDI Converter Figure 2 Connecting a 7508 CV YC to SDI Converter Figure 3 Connecting a PC without using a Null modem Adapter Tables Table 1 7508 CV YC to SDI Converter Features Table 2 Setting the Dipswitches Table 3 Technical specifications of the 7508 CV YC to SDI Converter Table 4 Structure of the Protocol Table 5 Instruction Set for the 7508 Table 6 Input Standard NYAURWNYR RR ns Oo NND ADDENDUM this data is included at the end of the Overview section This addendum adds the following information to the user manual No operator serviceable parts inside unit Use only the Kramer Electronics input power wall adapter that is provided with this unit Enur Disconnect power and unplug unit from wall before installing or removing device or servicing unit 1 For example model number AD2512C part number 2535 000251 2900 9999992 Al Introduction 1 Introduction Welcome to Kramer Electronics since 1981 a world of unique creative and affordable solutions to the infinite range of problems t
6. SDI Converter Figure 1 and Table 1 define the 7508 CV YC to SDI Converter oO 9 l 12V DC 2 1 YIC cV t SDI OUT INPUT KRAMER DigiTOOLS KRAMER CV YC to SDI Converter 7508 RS 232 ON Figure 1 7508 CV YC to SDI Converter RESERVED PEDESTAL STANDARD 1 STANDARD 2 STANDARD 3 RESERVED PROGRAM YIC KRAMER SIMPLE CREATIVE TECHNOLOGY Using Your 7508 CV YC to SDI Converter Table 1 7508 CV YC to SDI Converter Features Feature Function 1 12VDC 12V DC connector for powering the unit 2 SDI OUT 2 BNC Connector Connects to the SDI acceptor 2 3 SDI OUT 1 BNC Connector Connects to the SDI acceptor 1 4 Y C INPUT 4p Connector Connects to the s Video source 5 CVINPUT BNC Connector Connects to the composite video source 6 ONLED Illuminates when receiving power 7 RS 232 Port Connects to the PC or the Remote Controller 8 Dipswitches Dipswitches for setup of the unit 5 Using Your 7508 CV YC to SDI Converter You can use your 7508 CV YC to SDI Converter to convert professional quality composite video or s Video as the example in Figure 2 illustrates to one or two SDI video outputs To convert composite video or s Video to up to 2 SDI video outputs do the following Connect a composite video source for example a VCR to the CV BNC INPUT connector Connect an s
7. TA Figure 2 Connecting a 7508 CV YC to SDI Converter 5 1 Connecting a PC To connect a PC to the 7508 unit using the Null modem adapter provided with the machine recommended Connect the RS 232 DB9 rear panel port on the 7508 unit to the Null modem adapter and connect the Null modem adapter with a 9 wire flat cable to the RS 232 DB9 port on your PC To connect a PC to the 7508 unit without using a Null modem adapter e Connect the RS 232 DB9 port on your PC to the RS 232 DB9 rear panel port on the 7508 unit as Figure 3 illustrates depending on whether the PC has a 9 pin or 25 pin connector KRAMER SIMPLE CREATIVE TECHNOLOGY Using Your 7508 CV YC to SDI Converter PIN 5 Connected to PIN 5 Ground PIN 3 Connected to PIN 2 PIN 2 Connected to PIN 3 Female DB9 From PC PIN 4 Connected to PIN 6 PINS 8 7 1 Connected together Male DB9 To Switcher If a shielded cable is used connect the shield to PIN 5 PIN 7 Connected to PIN 5 Ground PIN 2 Connected to PIN 2 PIN 3 Connected to PIN 3 Female DB25 From PC Male DB9 To Switcher PIN 20 Connected to PIN 6 PINS 8 5 4 Connected together If a shielded cable is used connect the shield to PIN 7 DB25 and PIN 5 DB9 Figure 3 Connecting a PC without using a Null modem Adapter 5 2 Setting the Dipswitches Configure the 7508 unit by setting the dipswitches as Table 2 define
8. Video source for example a camera to the Y C 4p INPUT connector Connect both SDI outputs to SDI acceptors as follows when only one SDI output is required use either of the SDI outputs of the 7508 and leave the other SDI output unconnected Connect the SDI OUT 1 BNC connector to an SDI acceptor for example an SDI monitor Connect the SDI OUT 2 BNC connector to the second SDI acceptor for example an SDI monitor 4 5 Set the dipswitches as section 5 2 describes Connect the 12V DC power adapter to the power socket and connect the adapter to the mains electricity The composite video or s Video signal converts to SDI at both SDI OUT 1 and SDI OUT 2 Connect a PC if required to the RS 232 port see section 5 1 1 Switch OFF the power on each device before connecting it to your 7508 After connecting your 7508 switch on its power and then switch on the power on each device 2 To choose the CV input set the Y C DIP 1 OFF 3 To choose the Y C input set the Y C DIP 1 ON Using Your 7508 CV YC to SDI Converter SDI Acceptor 1 s Video Source erer SDI Acceptor 2 Composite Source EOT Lh T a i 12V DC 2 1 YIC cv t SDI OUT INPUT KRAMER DigiTOOLS KRAMER CV YC to SDI Converter 7508 222583 RS 232 ON N e NO CT odrea TEER Null e8fEEERL Modem EANN NEEA d 0o00 anani TR
9. ad EEPROM data low address 0 0 1 0 1 1 12 Write 12C 0 0 1 1 0 0 13 Read C 0 0 1 1 0 1 16 Error gai 0 0 07 0 57 Enable Power down save 1 1 1 0 0 1 61 identify machine 1 1 1 1 0 1 1 Note that the MSB s of the DATA D7 and the EXTENDED DATA E7 are in the fourth byte Communication Protocol DESCRIPTION OF INSTRUCTIONS INSTRUCTION 0 RESET DATA 0 initialize the machine When the machine is initialized it will send the RESET code DATA 0 If the machine receives this code it will reset to its power up state DATA I configure the machine to its factory default state When the machine receives this code all programmable parameters will be reset to their factory default values EXTENDED DATA set as 0 INSTRUCTION 1 READ INPUT STANDARD For sending to machine set DATA EXTENDED DATA 0 When replying DATA INPUT STANDARD EXTENDED DATA 0 The PC sends this instruction to the machine The machine replies by sending back the INPUT STANDARD defined as per the table below Table 6 Input Standard STANDARD E2 E1 E0 NTSC J M 0 0 0 PAL B G H I N 0 0 1 PAL M 0 1 0 Combination PAL N 0 1 1 NTSC 4 43 1 0 0 INSTRUCTION 3 READ BACK PANEL DIP SWITCH 1 VIDEO FORMAT read format When sending to machine DATA EXTENDED DATA set as 0 When replying EXTENDED DATA back panel DIP switch 1 0 CV 1 Y C
10. ers and Controllers GROUP 3 Video Audio VGA XGA Processors GROUP 4 Interfaces and Sync Processors GROUP 5 Twisted Pair Interfaces GROUP 6 Accessories and Rack Adapters GROUP 7 Scan Converters and Scalers and GROUP 8 Cables and Connectors 2 Download up to date Kramer user manuals from the Internet at this URL http www kramerelectronics com manuals html 3 The complete list of Kramer cables is on our Web site at http www kramerelectronics com click Cables and Connectors in the Products section 1 Your 7508 CV YC to SDI Converter In particular the 7508 e Converts the SDI on 2 buffered and reclocked SDI outputs e Automatically detects the input standard 50 60Hz generating the appropriate output e Uses true 10 bit digitizing making it ideal for the most demanding applications e Has an RS 232 port and can be controlled via a user friendly Windows based program that can modify video parameters such as contrast saturation and hue which may be stored in non volatile memory To achieve the best performance e Connect only good quality connection cables thus avoiding interference deterioration in signal quality due to poor matching and elevated noise levels often associated with low quality cables e Avoid interference from neighboring electrical appliances that may adversely influence signal quality and position your Kramer 7508 away from moisture excessive sunlight and dust Your 7508 CV YC to
11. hat confront the video audio and presentation professional on a daily basis In recent years we have redesigned and upgraded most of our line making the best even better Our 350 plus different models now appear in 8 Groups which are clearly defined by function Congratulations on purchasing your Kramer DigiTOOLS 7508 CV YC to SDI Converter which is ideal for broadcast and production video studios postproduction and duplication studios and non linear editing The package includes the following items e 7508 CV YC to SDI Converter e Power supply e Null modem adapter and Windows based Kramer control software e This user manual and the Kramer concise product catalog CD 2 Getting Started We recommend that you e Unpack the equipment carefully and save the original box and packaging materials for possible future shipment e Review the contents of this user manual e Use Kramer high performance high resolution cables 3 Overview The high quality Kramer DigiTOOLS 7508 CV YC to SDI Converter is a multi standard converter of analog video composite and s Video to SMPTE 259M serial digital video SDI Many professional video units on the market today such as Betacam decks and DVD players have high quality analog outputs and the 7508 is ideal for preserving the quality and minimizing the artifacts when converting to the digital domain 1 GROUP 1 Distribution Amplifiers GROUP 2 Video and Audio Switchers Matrix Switch
12. of initial technical adjustments set up including adjustment of user controls or programming These costs are the responsibility of the Kramer dealer from whom the product was purchased 3 Shipping charges HOW YOU CAN GET WARRANTY SERVICE 1 To obtain service on you product you must take or ship it prepaid to any authorized Kramer service center De Whenever warranty service is required the original dated invoice or a copy must be presented as proof of warranty coverage and should be included in any shipment of the product Please also include in any mailing a contact name company address and a description of the problem s 3 For the name of the nearest Kramer authorized service center consult your authorized dealer LIMITATION OF IMPLIED WARRANTIES All implied warranties including warranties of merchantability and fitness for a particular purpose are limited in duration to the length of this warranty EXCLUSION OF DAMAGES The liability of Kramer for any effective products is limited to the repair or replacement of the product at our option Kramer shall not be liable for aS 1 Damage to other property caused by defects in this product damages based upon inconvenience loss of use of the product loss of time commercial loss or 2 Any other damages whether incidental consequential or otherwise Some countries may not allow limitations on how long an implied warranty lasts and or do not allow the exclusion or limita
13. s Table 2 Setting the Dipswitches Dipswitch Set as follows 1 Y C ON for Y C source OFF for CV source 2 RESERVED OFF 3 PEDESTAL ON for pedestal 7 5 IRE offset selection for NTSC OFF for no pedestal AUTO NTSC_ PAL PAL M PAL N NTSC 4 SECAM AUTO 4 STANDARD 1 OFF ON OFF ON OFF ON OFF ON 5 STANDARD 2 OFF OFF ON ON OFF OFF ON ON 6 STANDARD 3 OFF OFF OFF OFF ON ON ON ON 7 RESERVED OFF 8 PROGRAM ON for upgrading firmware OFF for no upgrading firmware 1 NTSC offsets the black level within the active video signal by 7 5 IRE when selected Technical Specifications 6 Technical Specifications Table 3 includes the technical specifications Table 3 Technical specifications of the 7508 CV YC to SDI Converter INPUTS 1 composite video 1Vpp 75Q on a BNC connector 1 s Video 1Vpp 0 3Vpp 75Q on a 4p connector OUTPUTS 2 SDI SMPTE 259M ITU R BT 601 on BNC connectors BANDWIDTH 3dB 0 2dB to 5MHz DIFF GAIN 1 DIFF PHASE 1 K FACTOR lt 0 2 S N RATIO 57dB DIGITAL RESOLUTION 10 bits LUMA NON LINEARITY 1 CHROMA LUMA DELAY lt 15ns CONTROLS Brightness contrast hue saturation sharpness via RS 232 POWER SOURCE 12 VDC 220mA DIMENSIONS 12cm x 7 5cm x 2 5cm 4 7 x 0 98 x 2 95 W D H WEIGHT 0 3kg 0 66lbs ACCESSORI
14. s and feedback o 9001 2 lt E Institute of Quality amp Control ge Kramer Electronics Ltd Web site www kramerelectronics com E mail info kramerel com P N 2900 007508 REV 1
15. tion of incidental or consequential damages so the above limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from place to place NOTE All products returned to Kramer for service must have prior approval This may be obtained from your dealer This equipment has been tested to determine compliance with the requirements of EN 50081 Electromagnetic compatibility EMC generic emission standard Part 1 Residential commercial and light industry EN 50082 Electromagnetic compatibility EMC generic immunity standard Part 1 Residential commercial and light industry environment CFR 47 FCC Rules and Regulations Part 15 Radio frequency devices Subpart B Unintentional radiators CAUTION DO Servicing the machines can only be done by an authorized Kramer technician Any user who makes changes or modifications to the unit without the expressed approval of the manufacturer will void user authority to operate the equipment gt Use the supplied DC power supply to feed power to the machine B Please use recommended interconnection cables to connect the machine to other components 9 For the latest information on our products and a list of Kramer distributors visit our Web site www kramerelectronics com Updates to this user manual may be found at http www kramerelectronics com manuals html We welcome your questions comment
Download Pdf Manuals
Related Search