USER MANUAL - Forza Scooters
Contents
1. m l Do not modify your power scooter in any way not authorized by VMW Do not use accessories if they have not been tested or approved for VMW products Get to know the feel of your power scooter and its capabilities VMW recommends that you perform a safety check before each use to make sure your scooter operates safely Inspections prior to using your power scooter If equipped with pneumatic tires please check for proper tire inflations Please check all electrical connections and make sure they are tight and not corroded Please check all harness connections and make sure they are secured properly Please check the brakes Weight limitation Please refer to the specifications table for weight capacity information Power scooter is rated for a maximum weight capacity stay within the specified weight capacity for your scooter Exceeding the weight capacity voids your warranty VMW will not be held responsible for injuries or property damage resulting from failure to observe weight limitations Don t carry passengers on scooters Carrying passengers on scooter may affect the center of gravity resulting in a tip or a fall Tire inflation If your scooter 1s equipped with pneumatic tires 1 15 necessary to check the air pressure at least one time a week Proper inflation pressures will prolong the life your tires and ensure the smooth operation while riding Do not under inflate or over inflate your tires It 1s2. 275 WHEELBASE 0 9 GROUND CLEARANCE 7007 150 FOOTRESTS oom www vitamobilitywerks com 8 COMFORT ADJUSTMENT Adjustments for Seating Comfort Press the bottom to adjust the height of the headrest The flip up armrest height can be adjusted by turnin gi the adjustment dial NN 2 Adjust the seat back lever MET for seating back angle Turn the swivel lever downwards to rotate the seat Push the front lever upwards to move the seat forward and backward www vitamobilitywerks com 9 OPERATION OF CONTROL PANEL Function Descriptions SPECIFICATION Speed Sensor 7 Segment display 2 5 digits 1 decimal km h mph symbol High Low Turn jidicated as H and L symbols Speed Battery remaining capacity and charging indicator Power Indicator 6 squares Battery Icon Hour Minute Second display and setting ODO 99999 km max TRIP 99 9 max Power saving mode Blue LED Back up Lamps Brake Reverse modes Orange LED Right Indicator Flash mode Green LED Left Indicator Flash mode Green LED Including Reverse Mode left indicator and right indicator flashing simultaneously Red LED Malfunction Malfunction code Message 7 Segment display 141610 Warning symbol Red LED NOS Temperature CIE d TEMP Gauge ja Reverse Light Reverse symbol flashing 2 e
3. p 2 Z I www vitamobilitywerks com 10 2 2 Button amp LED FUNCTION SPECIFICATION MODE switch Function set Right Indicator control Headlight control control High Low speed us Back up lamps control Left Indicator O gt o gt Right Indicator Green Green LED Indicat Parking Red Headlight Blue YD Warning Red Back up lamp Amber LCD Backlight Illumination 700 mcd min Orange color 3 Usage Conditions ITEM SPECIFICATION Operation Voltage DC 16 32 V Storage Temperature 40 C 90 C Operation Temperature 25 55 C Meter Angle 30 of elevation while scooter assembly at Handle Cover LCD orientate to six o clock www vitamobilitywerks com 11 4 Characteristics Test General Characteristic Performance Test 20 5 Hardware Circuit SPECIFICATION RESULT n Lowest Operation 16V max Voltage Dynamic 200 mA max Consuming Current Backlight and LED light status mA 24 0V Static 5 mA max mA Key OFF status 5 OPERATING INSTRUCTION 5 1 Speed Sensor and Display ITEM SPECIFICATION Speed detection by speed sensor from transaxle with conversion at Operation Features 1400rpm equal to 60km h T 19 9 0 19 9 Digits range gt 19 9 displayed by integer 20 199 199 max Display Switch Button Initial setting at km h switch to
4. Temperature detected by temperature sensor NTC from transformation with Operation Feature signal 20 C 50 C 4 F 122 F Display Switch When display C degree stand for Celsius thermometer Button When display F degree stand for Fahrenheit thermometer 5 14 Reverse Indicator ITEM SPECIFICATION Take exterior forward backward switch as determinant signal When switch direct to forward no symbol on LCD Display Range Power Saving Mode N Reverse 7 When switch direct to backward symbol flashing on LCD www vitamobilitywerks com 21 5 15 Adjust Buttons ITEM SPECIFICATION Button ND MODE END Function set switch General Display Press SET for 3 seconds to reset TRIP at 00 0 Mode TRIP simultaneously for more than 2 seconds to enter Setting Mode then Hour MINJ start flashing 1 When Hour flashing Press to increase of number then press to enter Setting Mode of MIN 2 When MIN flashing MOGE Press to increase of number then press to enter Setting Mode of km h amp mph 3 When km h or mph flashing Press to choose km h or mph type then press to enter Setting Mode of C F 4 When C or F flashing Press to choose C or F Under setting mode if below situations happened will auto save the last Escape from Setting setting value then escape to general operatio
5. cut or have any exposed wires SEMI ANNUAL CHECKS 1 Check the motor brushes We recommended that your authorized dealer inspect the brushes every six months or sooner if your power scooter is not operating smoothly If inspection determines excessive wear on the brushes they must be replaced or motor damage will result www vitamobilitywerks com 28 Warning Failure to maintain the brushes could void the power scooter warranty To inspect or replace the motor brushes 1 Unscrew the motor brush caps 2 Remove the brushes 3 Inspect the brushes for wear 4 Replace the brushes if necessary Motor Brush caps Inspect the state of the battery terminals every six months Make sure that they are not corroded and the connections are tight Periodically apply a thin film of petroleum jelly on the surface of terminals to guard against corrosion CHECKS Make sure to keep the controller clean while protecting it from rain or water Never hose off your power scooter or place it in direct contact with water Keep wheels free from lint hair sand and carpet fibers Visually inspect the tire tread If less than 1mm 1 32 please have your tires replaced by your local dealer All upholstery can be washed with warm water and mild soap Occasionally check the seat and back for sagging cuts and tears Replace if necessary Do not store your scooter in damp or humid conditions as this will lead to m
6. MPH by MODE and buttons www vitamobilitywerks com 12 5 2 High Low Turn Speed Operation Features Symbols on LCD SPECIFICATION 1 Switch High Low speed by pressing button D once TRN as control signals Press one time High speed lt lt gt gt Low speed with memory storage 2 Take exterior turn switch as determinant signal TRN as control signals H symbol means High Speed SPEED L symbol means Low Speed SPEED L symbol flashing means Turn Speed www vitamobilitywerks com 13 5 3 Power Indication ITEM SPECIFICATION Remaining Voltage V Scale Bar Capacity 290 gt 25 42 a STD and I Flashing Low power Warning Warning LED Flashing 1 Scale status only decrease won t increase 2 When the remaining capacity was less than 30 warning sound two short sounds act at 5 seconds intervals Characters While a Key Off b Charging Mode c Sleep Mode warning sound released www vitamobilitywerks com 14 ITEM SPECIFICATION Remaining Voltage Capacity 40 lt 25 44 2 55 l gt 25 44 Fi Fi Fi x gt 26 18 maa 4
7. Rechargeable Battery 26Ahr 75Ahr 1 Short Circuit Protection 2 Reverse Power Protection Output Detection 3 Overheat Protection 4 Charging Plug Protection Operating Humidity 20 85 Measure 00000000 L 185mmxW 130mmxH 195mm 1 7K g Blue www vitamobilitywerks com 24 3 OPERATING INSTRUCTION 1 Make sure the battery charger output voltage 15 the same as the connecting battery 2 Plug in the power cord LED indicates green flash when AC power on 3 Connect the battery charger to the battery 4 Start charging please refer to 4 LED INDICATION 4 LED INDICATION 1 Green Flash Power on 2 Orange Charging 3 Orange Flash Pre charge 4 Green amp Orange Flash Charged 80 5 Green Full charged Floating charge 6 Red Flash Defect 5 TROUBLE SHOOTING 1 If green indicator 15 off Check AC input If it works functionally the battery charger may be defective 2 If green indicator keeps flashing and cannot turn to charging indication Check if the battery connector is connected successfully Check if there is any short circuit on the output connection The battery charger may be defective if the battery connection works functionally 3 If red indicator keeps flashing Check if the battery connection is reversed Check if there 15 any short circuit on the output connection Check if the environment temperature is too low 0 C The battery charger may be defective if the red indic
8. e 1 Fi Fi Fi Fi gt 2692 Ka ic c 5 Ei i 90 gt 28 5 6 IN Increase Frequency 1 Scale status only decrease won t increase Menangi 2 Take the PIN3 CH3 of charger as determinant signal enter Charging Mode when CH3 grounding L not only KEY ON or KEY OFF k Above scale bar status only for reference must take the indicator of charger emarks e as the precise diagnosis Character www vitamobilitywerks com 15 5 4 Clock SPECIFICATION Hour Min mode 12 00 Hour Min Setting 12 Hour format When Hour is between 1 and 9 o clock displayed at 1 9 5 5 Odometer ITEM SPECIFICATION Operation Features Odometer detected by the signal of Opto Coupler then converts into distance Switch km h means the odometer displayed as kilometer mph means the odometer displayed as mile 1 Display Range 00000 99999 ODO i M Accumulative 14 ae ai Display ODO 2 Once the total mileage up to 99999km 62149mile 99999 1 609mile the counter will restart from 00000 1 Display Range 00 0 99 9 p E D LL TRIP Counter L D z UL L L LI 2 When over 99 9km display stop counting won t restart from 00 0 1 Odometer indication display on ODO mode when Power On then switch Operation status to TRIP mode after 5 seconds 2 TRIP
9. not been used This is to make sure that the electrolyte is always at the top level If the battery cannot be charged Orange light cannot turn to Green or if the Orange light turns to Green immediately please check it with the technicians The battery may be defective The voltage difference between the two batteries on a power unit cannot be more than 0 5 V the battery case should be inspected for cleanliness and evidence of damage If the charger indicates red light please kindly check if the charger is defected or if the cable wiring connection is poor Please keep the battery and connectors clean otherwise the charging condition will be poor www vitamobilitywerks com 27 SCOOTER MAINTENANCE amp REPAIR Your power scooter is designed for minimal maintenance However like any motorized vehicle it requires routine maintenance To keep your scooter for years of trouble free operation we recommend you follow the following maintenance checks as scheduled DAILY CHECKS 1 Visual check on the conditions of tires 2 Inspect the battery condition meter on the controller to determine if batteries need to be charged WEEKLY CHECKS 1 Your power scooter comes with standard pneumatic tires If your power scooter comes with optional air tires make sure to maintain the pressure of the tires between 30 35 psi MONTHLY CHECKS 1 Visually inspect the controller harnesses Make sure that they are not frayed
10. External Temperatare Senser 2 2 Throttle 4 Throttle Wiper 3 Ke 1 Tail Light Hand Brake Key Switch 1 Left Lis Right Head Light m Throttle 4 Te Burer Throttle Wiper 3 Throttle 12 OH 69696969 pto T fy EOY eS Key Switen 11 FR Buzzer 5 Battery adimi __ ______ ForwardiReverse 7 www vitamobilitywerks com 31 V7x BOM LIST DRAWING 1 FRONT TILLER COVER 21 TURNING COUPLING 35 SIDE COVER R 2 TILLER FRAME 22 SPEED METER 35 REAR COVER 3 BUZZER 23 FRONT HUB 37 PLUGIR L 4 RUBBER DUST COVER 24 FRONT TYRE DISK BRAKE SET 5 TILLER RAM MECHANISM 25 BEARING TRANSAXLE 6 HANDEL CAP 26 FRONT AXLE R L 4d SUSPENSION BRACKET 7 HANDEL GRIP 27 CHARGER 41 REAR HUB 8 BRAKE LEVER 28 FR COVER 42 REAR TYRE 9 REAR VIEW MIRROR 29 SUSPENSION SPRING 43 BATTERY 10 REAR TILLER COVER 30 SUSPENSION ARM R L 44 SIDE COVERL 11 CONTROL PANEL 31 MAIN FRAME 45 FLOOR 12 FR SWITCH 32 REAR FENDER 46 REAR SUSPENSION 13 POTENTIOMETER COMBINATION 33 REAR BASKET BI EN 14 WIGWAG lt 48 REAR BUMPER 15 WIGWAG PAD 6 49 LAMP BASE 16 FF d T 50 REAR INDICATOR 17 FF COVER 51 LAMP CAP 18 FRONT BUMPER atl 52 SEAT SLIDING POST 19 HEADLIGHT 3 53 SEAT BASE 20 HEADLIGHT BRACKET 2 jamuan CAPTAIN SEAT ASM 12 15 e 13 57 FRONT BUMPER BRACKET www vitamobilitywerks com 32 WARRANTY DECLARATION Q
11. USER MANUAL V 7x Vita Werks VITA MOBILITY WERKS www vitamobilitywerks com SAFETY INSTRUCTION General elt Do not make a sharp turn or a sudden stop while Do not ride your scooter in traffic riding your scooter www vitamobilitywerks com 2 Do not ride your scooter during snow in order to Do not allow unsupervised children to play near avoid accident on slippery road this equipment while the batteries are charging Warning Don t operate your scooter for the first time without completely reading and understanding this user manual 1 Don t operate scooter on public streets and roadways Be aware that it may be difficult for traffic to see you when you are seated on the scooter Obey all local pedestrian traffic rules Wait until your path is clear of traffic and then proceed with extreme cautions 2 To prevent injury to yourself or others always ensure that the power is switched off when getting on or off of the scooter 3 Always check that the drive wheels are engaged drive mode before driving Do not switch off the power when the scooter is still moving forward This will bring the chair to an extremely abrupt stop 4 Do not use this product or any available optional equipment without first completely reading and understanding these instructions If you are unable to understand the warnings cautions or instructions contact a healthcare professional the dealers or te
12. ator still keeps flashing 4 Charging indicator orange cannot turn to green The battery might be defective please stop charging and have the battery be repaired 5 If the charging indicator orange turns to green fully charged immediately The battery may be in well charged condition The battery may be defective 1f the battery 1s not fully charged www vitamobilitywerks com 25 6 CAUTION 1 Before using the battery charger read all instructions and cautionary markings 2 Use the battery charger in a well ventilated area 3 To avoid the risk of injury charge only lead acid or gel cell type rechargeable batteries 4 Please turn off the power after charging Charging Port Important Always charge your batteries in well ventilated areas The charger is intended for indoor use only Please protect it from the moisture For maximum performance it is recommended that you replace both batteries at the same time if the batteries are weak Ifthe scooter will not be used for a long period of time arrange to have the batteries recharge at least once every month to avoid deterioration of the batteries www vitamobilitywerks com 26 BATTERY INSTRUCTION amp MAINTENANCE Read through the charger operating instruction before using it Make sure you charge the battery every time after you use the power chair or scooter Charge the battery at least 24 hours a week if the power chair or scooter has
13. can be reset to 00 0 www vitamobilitywerks com 16 5 6 Headlight Control ITEM SPECIFICATION Take exterior headlight switch as determinant signal 1 Switch on off the head light by pressing button once then Operation Feature LED will turn on off simultaneously 2 LCD backlights turn on turn off with head light When motor stop the modulation down to 30 Headlight P Saving Mod OWer DAVIS VOTE When motor act 100 output power Headlight While a KEY OFF b Power Saving mode c Sleep mode all functions closed 1 2 2V gt WIP gt 2 8V 100 Full power 2 2 2V lt WIP gt 2 8V 100 Full power 3 Full Half power switch at real time 4 The determination of Reversing Mode need to consider the motor direction and panel setting 1 Loop Load 24V 50W max Remarks 20 2 With short circuit and overload protection Usage Condition Determinant Condition www vitamobilitywerks com 17 5 7 Back up Lamp Control ITEM SPECIFICATION Take exterior back up lamp switch as determinant signal 1 Switch on off the head light by pressing button gt once then Operation Feature LED will turn on off simultaneously 2 LCD backlights turn on turn off with head light When motor changes from act go forward to stop the lamp reinstated Control Mode after flashing for 3 sec Brake lamp Mode Determine as Reversing Mode back up lamp keep
14. chnical supports before attempting to use this equipment otherwise injury or damage may occur www vitamobilitywerks com 3 10 11 12 13 14 15 16 17 18 19 20 There are certain situations including some medical conditions where the scooter user will need to practice operating the scooter in the presence of a trained attendant A trained attendant can be defined as a family member or care professional especially trained in assisting a scooter user in various daily living activities Consult with your physician if you are taking any medication that may affect your ability to operate your scooter safely Do not attempt to lift or move a power scooter by any of its removable parts including the armrests seats or shrouds Personal injury and damage to the power chair may result Never try to use your scooter beyond its limitations as described in this manual Please do not sit on your scooter while it is in a moving vehicle Keep your hands away from the wheels tires while driving scooters Be aware that loose fitting clothing can become caught in the drive tires Consult your physician if you are taking prescribed medication or if you have any certain physical limitations Some medications and limitations may impair your ability to operate scooters in a safe manner Be aware when the drive mode is unlocked or locked Don t remove anti tipper if there 15 any tipper equipped with the scooter Contact
15. critically important that 30 25 psi 2 2 4bar tire pressure be maintained in pneumatic tires at all times Inflating your tires from an unregulated air source could over inflate them resulting 1n a burs tire www vitamobilitywerks com 5 Temperature 1 Some of the parts of the power scooter are susceptible to change in temperature The controller can only operate in temperature that ranges between 25 50 2 At extreme low temperatures the batteries may freeze and your power scooter may not be able to operate In extreme high temperatures 1t may operate at slower speeds due to a safety feature of the controller that prevents damage to the motors and other electrical components ELECTROMAGNETIC INTERFERENCE EMI The rapid development of electronics especially in the area of communications has saturated our environment with electromagnetic EM radio waves that are emitted by television radio and communication signals These EM wave are invisible and their strength increases as one approach the source All electrical conductors act as antennas to the EM signals and to varying degrees all power wheelchairs and scooters are susceptible to electromagnetic interference EMI The interference could result in abnormal unintentional movement and or erratic control of the vehicle The United States Food and drug Administration FDA suggests that the following statement be incorporated to the user s manual for all power scooter like
16. flashing Reversing lamp Mode Reverse warning sound can be set by panel Turn on Turn off While a KEY OFF b Charging Mode c Sleep Mode all functions U Conditi closed sage Condition Brake lamp amp Reversing lamp Mode won t be limited by Back up lamp switch on or off 1 2 2V gt WIP gt 2 8V 50 Half power 2 2 2V lt WIP gt 2 8V 100 Full power Determinant Condition 3 Full Half power switch at real time 4 The determination of Reversing Mode need to consider the motor direction and panel setting 1 Loop Load 24V 50W max Remarks ee 2 With short circuit and overload protection www vitamobilitywerks com 18 5 8 9 10 Indicators and Parking Lamp Control ITEM SPECIFICATION Take exterior left right indicators and parking lamps switch as the Operation Feature determinant signal Press button once the right indicator and D turn off j left indicator and flashing warning sound act Press turn off left indicator again to Control Mode Left direction lamp 4 y Press button gt once the right indicator and lt turn off Right direction lamp left indicator and 19 flashing warning sound act Press D again to turn off left indicator YAN M ao Press button D once turn on right left indicators and lt flashing warning sound act Press D again to turn off the Parking lamp func
17. ildew and rapid deterioration of the upholstery parts All moving mechanism will benefit from simple lubrication and inspection Lubricate using petroleum jelly or light oil Do not use too much oil otherwise small drips could stain and damage carpets and furnishings etc Always perform a general inspection of the tightness of all nuts and bolts www vitamobilitywerks com 29 TROUBLESHOOTING amp FAULT REPAIR S Drive controller Your scooter is fitted with S Drive controller which continuously monitors the operating conditions of your scooter If it detects a problem it will indicate with error message by flashing light on the power ON OFF light You must count the number of the flash and see the list to check what kind of error has happened according to the number If you experience any technical problems it is recommended that you check with your local dealer before attempting to troubleshoot on your own The following symptoms could indicate a serious problem with your power scooter Contact your local dealer if any of the following arises 1 Motor noise 2 Frayed harnesses 3 Cracked or broken connectors 4 Uneven wear on any of tires 5 Jerky motion 6 Pulling to one side 7 Bent or broken wheel assemblies 8 Does not power up 9 Powers up but does not move PG S Drive controller PG D Drive Controller continuously monitors the operating conditions of your scooter If it detects a problem it will indicate with error
18. message by flashing light You must count the number of the flash and see the list to check what kind of error has happened according to the number S Drive Controller Troubleshooting 1 Bar The battery needs charging or there is a bad connection to the battery Check the 1 connections to the battery connections are good try charging the battery the controller 59 The motor has a short circuit to a battery connection Contact your service agent The freewheel switch is activated or the manual brake disengagement mechanism 15 operated Check the position of the switch or lever lA There is a bad connection to the motor Check all connections between the motor and The S drive is being inhibited from driving Inhibit 2 is active This may be because the me battery charger is connected or the seat is not in the driving position 7 Bar A throttie fault is indicated Make sure that the throttie is in the rest position before switching on the scooter 8 Bar A controller fault is indicated Make sure that all connections are secure ssa 9 Bar The parking brakes have a bad connection Check the parking brake and motor Connections Make sure the controller connections are secure 10 Bar An excessive voltage has been applied to the controller This is usually caused by a poor 1 uo om battery connection Check the battery connections www vitamobilitywerks com 30 CIRCUIT DIAGRAM
19. n mode 1 No any operation of ADJ button for 20 sec 2 Press MODE and at same time for more than 2 sec 1 Hour Min km h or mph C or F offer Cyclical Switch function 2 When adjusting Hour Min press to increase number if press Operation Status for more than 2 seconds the number will increase continuously until button released setting value with Cyclical Switch function only 2 seconds from 0 to 9 If Hour less than 10 the denary 0 doesn t display Button tones one short B1 sound www vitamobilitywerks com 22 5 16 LCD Backlight ITEM SPECIFICATION When pressing MODE and buttons the backlight will be turned LCD Backlight on voluntarily and turned off No any operation of ADJ button more than 5 sec 6 System Configuration SPECIFICATION Ds162K01 Series Charger CTE 8A Battery WP12280 2 Series connection WigWag CTE NCW KOOI 24V 50W max Tire Diameter Tire diameter circumference of mm Circumference www vitamobilitywerks com 23 CHARGING INTRUCTIONS Battery Charger Instruction Power Cord Output Plug to Battery Indicator Green Flash Power On 1 APPEARANCE Orange Flash Pre Charge Orange Charging Green amp Orange Flash Charged 80 Green Full Charged Red Flash Defected 2 SPECIFICATION Charging Method Constant current two stage constant voltage Battery Application 24V Lead Acid
20. ssories or components or modifying the powered scooter may make it more susceptible to interference from radio wave sources Note It is difficult to evaluate the effect on the overall immunity of the powered scooter 5 Report all incidents of unintended movement or brake release to the powered scooter manufacturer and note whether there is a radio wave source nearby TURN OFF YOUR POWERED SCOOTER AS SOON AS POSSIBLE WHEN EXPERIENCING THE FOLLOWING gt Unintentional scooter movements gt Unintended or uncontrollable direction gt Unexpected brake release The FDA has written to the manufacturers of power scooters asking them to test new products to be sure they provide a reasonable degree of immunity against EMI The FDA requires that a powered wheelchair should have an immunity level at least 20 V m which provides a reasonable degree of protection against more common sources of EMI The higher the immunity level the greater the protection Your powered scooter has an immunity level of 20 V m which should protect against common sources of EMI Warning The scooter itself can disturb the performance of the electromagnetic fields such as emitted by alarm systems of shops www vitamobilitywerks com 7 TECHNICAL SPECIFICATIONS REAR CASTER ANTITIPPER TURNING RADIUS 600mm 63 LENGTH 0002 WIDTH 20mm HEIGHT SEATWIDTH __________ 20 SEATHEIGHT SEATDEPTH BACKHEIGHT ________
21. the v7x Power scooters may as susceptible to electromagnetic interference EMI which is interfering electromagnetic energy emitted from sources such as radio stations TV stations amateur radio HAN transmitter two way radios cellular phones and alarm systems of shops The interference from radio wave sources can cause the power scooter to release its brakes move by itself or move unintended directions It can also permanently damage the powered scooter s control system The intensity of the EM energy can be measured in volts per meter V m Each powered scooter can resist EMI up to a certain intensity This is called immunity level The higher the immunity level the greater the protection At this time current technology is capable of providing at least 20 V m of immunity level which would provide useful protection against common sources of radiated EMI Following the warnings listed below should reduce the chance of unintended brake release or powered scooter movement that could result in serious injury 1 Do not turn on hand held personal communication devices such as citizens band CB radios and cellular phones while the powered scooter 1s turned on 2 Be aware of nearby transmitters such as radio or TV stations and try to avoid coming close to them www vitamobilitywerks com 6 3 If unintended movement or brake release occurs turn the powered scooter off as soon as it is safe 4 Be aware that adding acce
22. tion Usage Condition While a KEY OFF b Charging Mode c Sleep Mode all functions closed Flicker Frequency 1 sec Warning Sound One short B1 sound per second Frequency Left Right indicators have priority to Parking lamp lt EX gt Determinant Condition 7 Parking lamp turned on already now you start Right indicator function the flashing indicator lamps will change from both side left amp right to right side and the Parking lamp function will be closed 1 Load circuit for left direction light 24V 50W max Remarks 2 Load circuit for right direction light 24V SOW max 3 With short circuit and overload protection www vitamobilitywerks com 19 5 11 Malfunction Message Take the connector pin KEY of controller as determinant signal then Operation Feature converts it into digital code When the controller send out an error message red LED flashing with controller signal at same time the Error message code will show on LCD Usage Condition i NH x Flicker Frequency sec Controller Q message LED Flicker Flicker Status When scooter power on the control panel will go through a self test routine Initial Status the backlight and all LCD segments will be tuned on for 3 seconds then switch automatically to the general operation mode ODO www vitamobilitywerks com 20 5 13 Temperature meter TEMP ITEM SPECIFICATION
23. uality Warranty Declaration Products are to be fit for purpose and of excellent quality and performance For valid warranty claims VMW will at their discretion replace repair refund items mutually agreed to be defective VMW s Warranty as Following gt gt gt Frame Two year limited warranty Controllers One and a half year limited warranty Electronic Components and Charger One year limited warranty Warranty Exclusion The following items are not covered by warranty Motor brushes lt gt Wheel Tires lt Pads Seat Cushion lt Fuses Bulbs lt Tiller Cover Rear Shroud lt gt Front Shroud lt gt Batteries and Consumable parts Any damage or defect of any nature occurring from the misuse abuse of the product improper operation or improper storage is not to be covered The warranty 15 to start from the date of arrival of our products VAW Vita VITA MOBILITY WERKS www vitamobilitywerks com 33
24. with tools can cause electrical shock and do not connect an extension cord to the AC DC converter or the battery charger Do not attempt to lift or move your scooter by any of its removal parts such as the armrests seats or shroud When climbing an incline don t drive at an angle up the face of the incline Drive your scooter straight up the incline This greatly reduces the possibility of a tip or a fall Don t climb a slope steeper than the scooter s limitation Don t attempt to have your scooter proceed backward down any step curb or other obstacle This may cause the scooter to fall or tip Always reduce your speed and maintain a stable center of gravity when cornering sharply Don t corner sharply when driving scooters at higher speeds Operating 1 rain snow salt mist conditions and on icy or slippery surfaces may have an adverse affect on the electrical system Never sit on your scooter when it is being used in connection with any type of lift or elevation product Your scooter is not designed with such use in mind and any damage or injury incurred from such use is not the responsibility of VMW www vitamobilitywerks com 4 Modifications VMW Medical Product has designed and engineered power scooters to provide maximum utility However under no circumstances should you modify add remove or disable any part or function of your power scooter Personal injury and damage to the power chair may result
Download Pdf Manuals
Related Search