Instruction Manual
Contents
1. senko crouP Advanced Com DO nents For your safety operation This product has been designed and manufactured to assure personal safety Improper operation can result in bodily injury and serious damage to this product Please read and observe all warnings instructions given in this operation manual Wear safety glasses before handling optical fiber to protect the eyes Small pieces of glass fiber are very sharp and might get into the eyes or under the skin and cause injury Never look into the end of a connector or an optical fiber which may have a laser coupled to it Laser light may damage your eyes Please note that laser light is not visible If working in high places please be careful not to drop any tools Please use a wrist strap etc Composition Connector with wedge 10pcs Boot 10pcs Fiber holder for 900 um fiber 1pc Assembling Jig 1pc SC for 900um fiber Fiber Holder for 900um fiber k Following tools shall be required for assembling the above parts 1 Fiber Cleaver 2 Jacket Remover SENKO ADVANCED COMPONENTS INC Americas Asia USA EAST 1 888 32 SENKO HONG KONG 852 2121 05 16 SHANGHAI 86 21 5830 4513 SHENZHEN 86 755 2533 4893 WUHAN 86 27 8725 9057 Sales Asial senke com Europe USA WEST 1 858 623 3300 Sales Americas senke com UK 44 0 118 982 1600 ALY 39 011 839 9828 POLAND 48 71 79 88 152 Sales Europe senko com XP Fit Plus SC 900 um Fie2. ible push the back end into the fiber holder k Setting fiber on the C s fiber holder Bend fiber several times 7 Clean bare fiber AS i by moving it with your 4 Install boot onto fiber Remove fiber jacket using the fiber jacket remover with a lint free finger back and forth e Gauze Pad HP to 35 mm of pure Alcohol ew ee right please start with Length of 900 um jacket using Pe a new fiber from 900 um fiber jacket remover down jacket is within 2mm ength of Me fiber After closing covers 1 and 2 YO N 9 close cover 3 N eav sane yS If out of tolerance rework EN from step 5 Set the fiber holder to the guide rail Be sure the fiber aligns with the U groove Slide the fiber holder S slowly until it stops Not following this step will cause an air gap between fibers creating high insertion loss Insert until clicking sound is heard Push the arms to remove the Not following this step correctly can cause damages to the fiber ends hold the sides of the fiber holder so that the fiber moves freely Use a visible light source to test connection no visible ligh Bad connection Open covers 1 and 3 visible ligh Finished product senko crour Advanced Com pon ents D Attention 1 Attach the wedge ona connector again make sure there IS NO space between the wedge and the con
3. ld Installable Connector Instruction Manual ETP 1008 001 02 Precautions 1 Improper assembly will result in a loss of performance Please read instructions given in this operation manual 2 The product is sensitive to dirt or dust Do not take connector out of the package until it is to be used 3 The performance will be influenced by the cleaved fiber surface condition Please use a cleaver that has a good blade 4 Please insert the fiber into the connector slowly If the fiber is roughly inserted it might be damaged or broken leading to product failure Broken fiber could be scattered in all directions 5 Do not remove the dust cap until the connector has been completely assembled 6 A proper amount of index matching gel is applied in the connector Do not insert fiber more than once 7 Product properties are referenced to specification No ETP 0109 001 xx Assembly tools example 1 Fiber cleaver FC 7 2 Jacket remover JR 25 2 Jacket remover JR MO3 WWW SENKO COM Asia Pacific Japan AUSTRALIA 61 0 3 9755 7922 TOKYO 81 0 3 3262 0211 Sales Asia Pacific senke com Sales Japan senko com Middle East North Africa PO Box 262381 Jebel Ali Dubai UAE Sales MENA senke com 1 Preparing connector 2 Setting connector 3 Preparing the fiber holder Open covers 1 2 and 3 before using the holder Make sure the guide is not visible from the rear of the fiber holder If the guide is vis
4. nector 2 Push the inserted fiber and create the bend again DO NOT PULL FIBER OUT FROM THE CONNECTOR Grip the fiber 80 10 mm position from the end of the connector 3 Remove Push the arm to the Wedge remove the wedge 4 Re install the boot
Download Pdf Manuals
Related Search