Tubular Motor Control Panel User Manual TM5101
Contents
1. connection instruction of control panel when connecting applied to the actual line circuit to choose the top or bottom holes of control panel After checking there is no errors install the decorative covers Complete the installation2. button 1 and button 2 at the same time Old one an STEP2 2A then press button 2 to let LED turns into red New transmitter can be learned lll Product picture 1 LED Power indicated light 2 Transmitter learning and deleting button 3 5 Open close button 4 Stop button 6 Fuse 10A 7 Fuse 0 5A 8 terminal blocks L N connects working power COM A Y connects motor Photo connects photocell NC switch 24VAC output 24V AC voltage AC motor f4VAC out PH VIII Installation Process STEP3 Press the same button on the new transmitter twice The learning process done In this way new transmitter can be learned without pressing the learning button on the control board New one N COM UP DOWN _ 24VAC PHOTO i ia i i t WED F1 10A Motor Fuse Radio Learn Bullon F2 M Y yY _10 5A Control Fuse 24VAC Output photocell A aA NC L Ncoma w 24vac py v Connection instruction In the installation position drill two 6 holes with the depth of about 35mm and distance is 13mm 3 Install panel Fix the top side of buckle to the installation hole of the back of control panel the other side of buckle is in close connection with outer surface 2 Install buckle Fix the expansion screws buckle and 4 25 screw on the wall Note the direction of buckle fix the deep side on top as shown in picture 2 4 Connection amp install decorative covers According to the
3. Tubular Motor Control Panel User Manual TM5101 TM5108 TM5121 TM5128 l Specification 1 Working voltage 220VAC 110VAC 50HZ 60HZ 2 Loading capacity 2HP 240VAC 3 Working frequency 433 92MHz 4 Built in fuse electrocircuit 0 5A motor 10A 5 Temperature range 20 C to 60 C 6 Code Rolling code Fixed code 7 Size 113x74x44MM IV Set up 1 Learning memorizing transmitters 2 Erasing Transmitter V Operational process 5 1 Three button control system with transmitter II Safety Instruction 1 For security please read the instructions carefully before initial operation making sure that the power is off before connection 2 The received signal may be interfered by other communication devices e g the wireless control system with the same frequency range 3 It is forbidden to control the high risk coefficient equipment system e g cranes 4 It should be applied in dry indoor place or in the electric appliance place Press the learning button on the panel LED turns into red and gets into learning state press the same button twice on the same transmitter LED blinks for a while and turns into green shows transmitter has been learned successfully Continue pressing the learning button about 8s until LED turns green then release the learning button LED turns red about 1s then turns green It indicates that the erasing process is successful Button 1 2 3 in transmitter is in correspondence with open close
4. and stop 5 2 Single button control system Press Open motor works clockwise press stop press close motor works anti clockwise press stop and so on in a loop Single button control is only effective to the learned button if a new button of transmitter learned into the control panel the former one is useless e g if learned button at first and then button or the former button becomes invalid 5 3 Infrared sensor protection It only work when door closing Motor stops after 1 second and reverse when photocell signal disconnecting during door closing External photocell PHOTO port connects photocell normally close switch 1 Single button control refers to single button in transmitter A W V in control panel is in correspondence with open close and stop 2 Max running time means that the motor s maximum running time at a time is 100S the motor stops immediately if longer than 100S 3 A E Y in control panel and OPEN STOP CLOSE button in transmitter are in correspondence with open close and stop VI Model list Model 220VAC ThISLOL TMIS102 TMISLOS T3104 T5105 TM5106 TMS107 TM5108 Model 110VAC ThIS121 TMal22 TMSL23 TMIS124 ThIS125 TM5126 TMal27 TMal26 Frequency 433 92Mhz fixed code feces Trnsmitersorea o o aw wo wo wo wo VII Self learning learning new remotes by old remotes STEP 1 Use the trasmitter that already has been learned as old transmitter press
Download Pdf Manuals
Related Search