File - GSM Outdoors
Contents
1. either a tree screw optional accessory or supplied mounting strap You may refer to the mounting suggestions section in this manual www stealthcam net Toll Free 877 269 8490 24 K K STC 1550 Open the front housing and move the switch to the ON position At this point you have 30 seconds to make any program adjustments After 30 seconds the camera s green LED light will begin blinking and enter count down mode This is your indication to leave the coverage area within one minute After one minute the camera will enter either image burst mode or adjustable video mode based on your program setting The camera will then time out between 1 59 minutes depending on your setting The time between motion detection and the camera taking the pictures may vary due to lighting conditions charging of the flash program settings and battery power level The flash light will only activate in low light conditions When the camera is set to AVI capturing the camera cannot use the flash feature The quality of the video clip will turn out well in good daytime lighting conditions If the surrounding light conditions are not enough your unit will switch the AVI setting to a single image capturing automatically www stealthcam net Toll Free 877 269 8490 25 STC 1550 WW ZLake EU EG T Musto itarele ss The STC I550 cam offers the user different options for viewing the images The external LCD display on the front of the ho2. listed above www stealthcam net Toll Free 877 269 8490 33 STC 1550 Technical Specifications System Requirements and Compatibility Windows 98 98se 2000 Me XP Vista P 450MHz or equivalent processor 128MB SDRAM or above VGA Video Card with 32MB RAM for minimum Color 16 bit or higher If you have any questions regarding your PC specifications please call your PC manufacturer www stealthcam net Toll Free 877 269 8490 34 STC 1550 Camera Features and Specification Image sensor 1 3 mega pixels RGB color Built in 2 0 B amp W LCD display Built in 32M flash memories for image storage External memory support SD memory card up to 2 GB Resolution Options 5 0M 3M 1 3M 3 Capturing Options Single Continuous AVI Image performance for video stream 10fps in 320 x 240 pixels approx 10 seconds per section Auto white balance and auto expose Flash light strobe Auto amp Off control Real time clock for date and time stamping 4 digits LCD Image counter Battery low LED indicator Green Test LED indicator www stealthcam net Toll Free 877 269 8490 35 STC I550 TV out support for NTSC and PAL system Focusing 5 ft to Infinity High precision 4 P glass lens with IR coating Effective viewing Angle 49 deg PIR detection angle 48 deg Low power consumption Standby current lt 1mA Capture current lt 150mA Interface type USB 1 1 Power C size alkaline Batteries x 6 External power 12 volts batt
3. 0 Camera overview Front housing image with major parts indication Front housing Flash LCD Display Screen Low Battery Test Indicator Indicator Camera Lens Passive Infrared sensor PIR DC port www stealthcam net Toll Free 877 269 8490 STC I550 Open view image with major parts indication Battery compartment Cover LCD DISPLAY Mounting strap slots MENU Button ON OFF Switch Tree screw Confirm TEST i ount UP Down Button Button Button Button www stealthcam net Toll Free 877 269 8490 STC 1550 Side view with major parts indication Video out Jack USB Port www stealthcam net Toll Free 877 269 8490 STC 1I550 Picture Image Capacity SD card High Low Base AVI 16MB 13 17 32 8 32MB 26 34 64 16 64MB 52 68 128 32 128MB 104 136 256 64 256MB 208 272 512 128 512MB 416 544 1024 256 1 GB 832 1088 2048 512 2 GB 1664 2176 4096 1024 NOTE Picture Image Capacity Chart provides approximate number of images or AVI movies based on resolution setting and the size of memory card These figures may vary depending on the amount of detail in the image www stealthcam net Toll Free 877 269 8490 7 STC I550 e Model STC I550 Digital Scouting Camera e User Manual e USB cable e Strap www stealthcam net Toll Free 877 269 8490 STC I550 Warning Do not use different Voltage lead acid battery other than the one spec
4. 0 Time out To set the amount of time in minutes the camera will sleep between PIR triggering Flash o Auto Flash on base on surrounding light conditions o Off Turn off the flash Capture mode o 1P 9P 1 to 9 burst mode image capturing per PIR triggering o Video 5 to 90 seconds adjustable video per PIR triggering Resolution o 5 0M Select this option to capture a 5 0M pixels image High image quality o 3M Select this option to capture a 3M pixels image Low image quality o 1 3M Select this option to capture a 1 3M pixels image www stealthcam net Toll Free 877 269 8490 13 STC I550 Base image quality o Video resolution 320 x 240 This is the resolution during video capturing Batteries Status It shows the battery status o Full It shows the battery is full O o Low It shows the battery is low and front Low Battery indicator will also blink When the camera has detected low batteries Batteries are lower then 5 8 0 2Volts the camera unit will power off within 30 seconds automatically Please replace with new batteries otherwise the camera will not work properly Day and Time Displays the date and time that you have set on still image For AVI it will appear on the last frame Using Quick Time Player or Real Player Moon phase and Temperature Displays the moon phase and temperature For AVI it will appear on the last frame Using Quick Time Player or Real Player www stea
5. Stealth Cam STC 1550 User s Manual Toll Free Customer Support 1 877 269 8490 www stealthcam net Version 1 0 03 08 STC 1550 For Customer Service or Warranty Information Call Toll Free 877 269 8490 Stealth Cam LLC P O Box 539504 Grand Prairie TX 75053 9504 www steatlhcam net Stealth Cam Limited Warranty Your Stealth Cam scouting camera is covered by a 90 days Limited Warranty on parts and labor from the date of original purchase and purchases must be made through an authorized dealer The warranty covers defects in workmanship and materials The warranty does not apply to units which have been damaged or abused intentionally or unintentionally A purchase from individuals or unauthorized internet sites voids the warranty Tampering with or altering the unit will void the warranty Any unauthorized service will void warranty Original sales receipt must be produced for any warranty service and a Return Authorization RA number must be obtained from customer service at 877 269 8490 prior to returning product www stealthcam net Toll Free 877 269 8490 2 STC I550 Manual Contents Camera overview 4 Camera kit contents 8 Battery and memory Installation 9 Definitions 13 Set up and programming 15 Camera use 20 Mounting the camera 21 Viewing amp Deleting images 26 Memory compatibility chart 33 Technical Specs 34 General Information 37 Moon Phase Chart 39 www stealthcam net Toll Free 877 269 8490 STC I55
6. To view image in full screen press OK button Press OK button again will return to the thumbnail view from the full size image View AVI Clip on hand held TV monitor or home TV Follow the cable attaching instruction listed in previous section Monitor will display a thumbnail image in the memory Press UP or DN button to choose the AVI clip that you would like to see www stealthcam net Toll Free 877 269 8490 29 STC 1550 e Press the OK button to play back the AVI motion clip e To return to thumbnail image selection view press OK button at the end of the AVI clip Deleting images At any time while viewing images on Handheld TV or Home TV you may delete images one at a time or all at once e While viewing images either in thumbnail view or full screen press MENU once will enter delete mode The word dEL will be blinking 7 Please note you can not enter delete mode while the video clip is playing You must wait until the end of the video clip or while it is in thumbnail view e Press OK button to enter the DELETE amp FORMAT menu e Using the UP and DN buttons to select the desired function No Delete NO dL Delete one d ONE Delete ALL d ALL or FORMAT www stealthcam net Toll Free 877 269 8490 30 STC I550 Press OK to confirm your selection To return to thumbnail view you must press DN button and scroll through the option until you see No Delete NO dL press OK and
7. d exit to CAPTURING setting Set the Capturing sequence The Stealth Cam STC I550 can be programmed to shoot 1 9 pictures per triggering or 5 90 seconds of video www stealthcam net Toll Free 877 269 8490 16 STC 1550 e This word CAMERA will be blinking e Press OK button to choose picture mode then press the UP or DN button to select the desired capture setting number of pictures per triggering e Press OK to confirm your selection e f you want to choose video mode when the word CAMERA is blinking press UP to choose video mode Now the word VIDEO will be blinking Press OK to confirm your selection e Press UP or DN button to select the desired video length from 5 seconds to 90 seconds in 5 seconds increment e Press OK to save and exit to TIME OUT setting Set the Time out e The word TIME OUT will be blinking e Press OK button to choose the selection The digit will now be blinking ready for change www stealthcam net Toll Free 877 269 8490 17 STC 1550 Press UP or DN button to increase or decrease the time value in minutes from 01 to 59 minutes Press OK to save the setting and exit to Date amp Time setting Set Date and Time This camera uses the 24hr military time format The DATE will be blinking Press OK one more time to enter time setting first Minute digit will be blinking Press UP or DN to increase or decrease the minute value 0 59 Press OK to confirm
8. e sure that both door latches are securely locked in place Testing the camera coverage area One of Stealth Cam s many features is the ability to test the coverage area e After mounting the camera open front housing and slide the power to ON e After the font LCD screen has powered on press the TEST button this must be done with in 30 seconds or the camera will enter count down mode e Close the front housing e Walk around in the front of the camera to see if you have mounted the camera in the proper position A green indicator LED light on the front will blink when you have intruded the www stealthcam net Toll Free 877 269 8490 23 STC 1550 coverage area Adjust the camera position as needed and repeat testing until the desired coverage area is achieved When you have completed testing the coverage area there are 2 methods to exit the test mode a Open the front housing and press the TEST button to exit test mode The camera will then enter count down mode for 1 minute and the front green indicator will start blinking giving you 1 minute to leave the coverage area The camera will then enter PIR detection mode b As a safety precaution the camera will automatically enter 1 minute count down after it has been left sitting idle in test mode for more than 5 minutes Camera will then enter PIR detection mode Using the camera in PIR detection mode Mount the camera to tree or other sturdy object using
9. ery pack Image format Standard JPEG or Motion JPEG AVI www stealthcam net Toll Free 877 269 8490 36 STC I550 General Information Storing conditions Store in cool and dry location when it s not in use Operating Environment 14 to 104 deg F 10 to 40 deg C 20 85 relative humidity non condensing Special care instructions The camera is designed to be weather resistant Never attempt to immerse the unit in water or any other liquid This will damage the unit and void the warranty Use a soft lens cloth for cleaning lens Avoid touching lens with fingers Remove dirt or stains with a soft cloth dampened with water or neutral detergent Keep the STC I550 cam in a dry and cool dust free environment or container when it is NOT used Take the batteries out when the STC I550 cam is NOT to be used over a long period Avoid dropping the STC I550 cam on to hard ground Do not www stealthcam net Toll Free 877 269 8490 37 STC 1I550 disassemble the STC I550 cam e Do not mix new and old batteries e Do not open the camera for unauthorized service This could cause serious damage to the unit and will void the warranty This camera is a precision electronic device Do not attempt to service this camera yourself as opening or removing covers may expose you to dangerous voltage points or other risks May be protected by one or more U S Patent numbers 6 735 387 6 768 868 6 834 162 7 149 422 7 308 196 www
10. es and other debris away from the front of the camera so as not to block the camera lens or PIR sensor PIR Coverage Area Diagram EFFECTIVE DISTANCE 30 FEET HORIZONTAL www stealthcam net Toll Free 877 269 8490 20 STC I550 Mounting the camera Mounting the camera with Tree Screw Optional Accessory sold separately WASHER 1 NUT WASHER 2 SPANNER Sc TREE TRUNK e Hand twists the screw into the tree or post at the desired position e Attached the camera to the screw by turning the camera onto the mounting screw to the desired position e Tighten the stabilizer nut www stealthcam net Toll Free 877 269 8490 21 STC 1550 Do not over tighten as this may cause damage to camera housing Using the nut and washer that came with the tree screw tighten to the bottom of camera for greater stability Mounting the camera with the supplied strap Strap A PE TREE TREE TRUNK TRUNK Buckle e Insert the strap through the strap slots on the rear housing e Wrap the strap around the mounting surface Secure the strap and tighten the buckle in order to secure the camera www stealthcam net Toll Free 877 269 8490 22 STC 1550 Stealth Cam offers a Security Lock Bracket for uses exclusively with this camera For the latest Stealthcam accessories go to www stealthcam net or call toll free 877 269 8490 gt In order to obtain proper weather resistance please mak
11. ified in this section Doing so will damage the camera and will void the warranty The Stealth Cam STC I550 Advanced Digital Scouting Camera is designed to operate using two different types of battery power options NOTE Always have camera in the OFF position when installing or removing batteries Removing battery while the camera is in operation may damage the camera Batteries C cell The internal battery compartment accepts 6 x C cell batteries Be sure to use high quality brand name alkaline batteries Install batteries with correct polarity as noted inside the battery compartment www stealthcam net Toll Free 877 269 8490 9 STC I550 12V Lead Acid external battery The STC I550 is equipped with an external power jack designed to accept a barrel plug cable to attach to a sealed lead acid battery sold separately This will enhance the camera s field life Battery cable and complete 12V Lead Acid battery kits are available wherever Stealth Cam scouting cameras are sold or call toll free 877 269 8490 Only Stealth Cam external battery accessories are recommended e Insert the external battery barrel plug into the DC 12V jack on the bottom of camera housing e Turn the camera power on Please make sure the voltage and polarity are correct before connection Incorrect voltage or polarity will damage the camera Please note When both internal and external batteries are connected the came
12. ing on home TV attach the appropriate cable to the video www stealthcam net Toll Free 877 269 8490 27 STC 1550 OUT jack on the camera Insert the other end into the RCA video IN jack on the TV Make sure to switch to VIDEO IN mode on your TV See your TV owner s manual for directions Turn on both the camera and TV monitor Your camera is preset to NTSC TV out system by default If the handheld TV screen does not flicker then you do not need to set your TV out system If the handheld TV screen flicker then you will need to proceed to the next step to set up your TV out to PAL system Press the MENU button once This will bring up the word dEL on the camera s internal LCD screen When you see the word dEL blinking press UP button to enter TV out setting mode The word tu will be blinking Press OK The display tu n will be blinking Press DN button to select TV out in PAL System which is use in most European and Asian countries The word tu P will be blinking www stealthcam net Toll Free 877 269 8490 28 STC 1550 Press OK to confirm setting Press MENU to exit and continue with your image viewing Press OK to bring up the thumbnail images At this point you may use the UP or DN button to navigate though your thumbnail images On the upper left hand corner of your TV monitor it will display the word JPG or AVI to indicate whether that thumbnail is still image or video clip
13. lthcam net Toll Free 877 269 8490 14 STC I550 Set up and Programming When the camera is first turned on the internal LCD screen displays the camera status The following information is present on this screen Flash Mode Control The camera is pre programmed with Auto Flash setting e Switch the camera to ON position BS e To turn off the flash mode press the UP button A once within 30 seconds icon will appear on the top of the screen e To turn on the flash mode back to Auto setting press the UP button the second time 7 icon will appear on the top of the screen If no buttons are pressed after 30 seconds the LCD screen will power down to conserve battery life and enter 1 minute count down to enter PIR detection mode To re power the display www stealthcam net Toll Free 877 269 8490 15 STC I550 screen press and hold the UP or DOWN button until the status screen appears Programming the Stealth Cam STC I550 Switch the camera to the ON position LCD screen will display the camera status screen Press the MENU button within 30 seconds to enter programming mode If MENU button is not pressed within 30 seconds camera will automatically enter PIR detection mode Set the Resolution The first program setting is resolution The word RESOLUTION will be blinking e Press OK button to choose the selection e Press the UP or DN button to select the desired resolution HIGH LOW BASE and press OK to save an
14. ra will draw power from the higher voltage source first www stealthcam net Toll Free 877 269 8490 10 STC 1550 Memory Options Your STC I550 camera is equipped with 32MB built in flash memory The camera is also equipped with an expandable media card slot capable of accepting up to 2GB SD card sold separately With no memory card inserted into the slot the camera will use the built in 32MB memory If an SD card is inserted into the slot then the camera will bypass the built in memory and utilize the SD memory for image storage The front counter display will show the number of images on the built in memory unless the expansion card is inserted at which point the counter will only show the number of images in the expansion card Inserting SD card Make sure camera is in the OFF position whenever adding or removing memory e Insert SD memory card in to the SD card slot completely and in the correct direction as shown by the sticker located at the side of the housing e To remove the SD memory card depress the SD card and pull out the card gently www stealthcam net Toll Free 877 269 8490 11 STC I550 SD cards must be clean no images from other sources If you are using the SD card from other cameras please make sure to format the SD card in your computer using FAT formatting not FAT32 prior to use in the camera New cards are good to use straight from the package www stealthcam net Toll Free 877 269 8490 12 STC I55
15. stealthcam net Toll Free 877 269 8490 38 STC 1550 Moon Phase Symbol Chart Lunation from to 29 or 30 Product specifications are subject to change Stealthcam is not responsible for any photographic or typographical errors www stealthcam net Toll Free 877 269 8490 39
16. the minute setting and enter hours setting Hour digit will be blinking Press UP or DN to increase or decrease the hour value 00 23 Press OK to confirm the hour setting and enter month setting Month digit will be blinking Press UP or DN to increase or decrease the month value 1 12 www stealthcam net Toll Free 877 269 8490 18 STC 1550 e Press OK to confirm the month setting and enter date setting e Date digit will be blinking Press UP or DN to increase or decrease the date value 01 31 e Press OK to confirm the date setting and enter year setting e Year digit will be blinking Press UP or DN to increase or decrease the year value Once this is done press OK You ll see the word dEL blink Now press MENU to exit program setting and back to status screen At the end of each program set up selection you may press MENU to exit and return to camera status ready screen for the 1 minute count down mode to enter PIR capturing www stealthcam net Toll Free 877 269 8490 19 STC I550 Using the camera Once all program setting has been completed your Stealth Cam is ready for field use Getting started It is recommended that you mount the camera 4 5 ft off the ground with the camera pointed at a slight downward angle Be sure to avoid mounting the camera facing east or west as the rising and setting of the sun could produce false triggers and overexposed images Clear all branch
17. then press MENU This will return back to either thumbnail view the full screen image that you were viewing If you choose to delete one picture at a time d ONE it will delete the picture that you selected on the thumbnail view or the image that is on full screen If you choose to delete all images d ALL it will delete all images Once images are deleted from the memory you will return to status screen If you choose to format your memory it will erase all images This feature is particularly useful if you don t want to look www stealthcam net Toll Free 877 269 8490 31 STC 1550 through the images one at a time Once this is done press DN button and scroll through the options until you see No Delete NO dL press OK and then press MENU This will return to status screen www stealthcam net Toll Free 877 269 8490 32 STC I550 SD Memory Card Compatibility Chart The following cards have been tested and approved for use in the STC I550 model PQI 32MB 64MB 128MB 256MB 512MB San Disk 32MB 64MB 128MB 512MB 1GB 2GB Panasonic 32MB 64MB 256MB 512MB Toshiba 32MB 64MB 128MB 256MB 512MB King Mate 32MB 64MB 128MB 256MB 512MB Lexar 32MB 512MB Kingston 128MB 256MB 512MB Kodak 128MB 256MB 512MB Dan Elec 128MB 256MB 512MB PNY 128MB 256MB 512MB 2GB First Champion 1GB Proper camera operation cannot be guaranteed when using memory card NOT
18. using will show the number of images in memory To wake the camera from PIR detection mode press and hold either the UP or DN button for about 5 seconds The instructions below are based on starting from a camera that is turned off Viewing images by computer download The Stealth Cam STC I550 Digital Scouting Camera is a plug and play USB storage device This means users of Windows 2000 ME XP and Vista operating systems need not install the camera driver This camera is not MAC compatible If you are using Windows 98SE operating system you can download the driver from the Stealthcam website PC with USB Port www stealthcam net Toll Free 877 269 8490 26 STC I550 Viewing the images on your computer e Slide the power switch to OFF location e To view the images simply plug one end of the USB cable into an available USB port on your computer e Plug the other end of USB cable into the camera The camera will automatically power ON and display the word USb on the LCD screen e Atthe same time your computer will recognize the camera as a mass storage device and will be found under MY COMPUTER Viewing the image on a handheld LCD TV video monitor or your home TV equipped with an RCA input jack cables sold separately For viewing on handheld LCD TV attach the appropriate cable to the video OUT jack on the camera Insert the other end into the video IN jack on handheld LCD TV monitor For view
Download Pdf Manuals
Related Search