Telit RoadStar Car Phone Installation Guide
Contents
1. Explain that the Phone is an amplifying system that receives all environmental noise and therefore it is preferable to speak with a closed window Check whether microphone and antenna are installed on the same side If they are install microphone as per the instructions Check whether eye contact exists between speaker and microphone Check for improper voltage connection check whether voltages are connected as per instructions If it does change location accordingly Change voltage source in accordance with instructions Phone switches on and off by itself Check minus connection Black wire connect minus to car body Check voltage contacts Tighten loose contacts Phone switches on and off by itself Check fuse Check connection to voltage source green cable Replace fuse Tighten connection to voltage source Ensure a 250V 2A fuse is used Phone does not switch off after switching off car Check connection to power source green cable Tighten connection to power source Phone does not switch off after switching off car Check connection to power source Check fuse red cable Mounting instructions Replace fuse Tighten connection to power source Telit 7 Appendix Finding IMEI code 1 Type code 06 2 Find locking code 5625 Mounting instructions2. Ensure the connection minus point is on the car body only Use a cable shoe tin screw and springy disc Green To turn on the cellular 12V 24V Ignition Determine the correct point with a voltmeter Ensure a 250V 2A fuse is used Mounting instructions Telit Installing RF Antenna 5 7 1 Where to Locate the Antenna e The preferred location for the antenna is on the right side of the windshield e If other communication system is installed in the car please locate the antenna as far as possible from the other phone antenna Recommended distance is 30cm Some car vendors such as Renault feature a radiation filter on the windshield Note Therefore it is necessary to install the antenna on a side or back window hi In vehicles vvith air bags on the beam vvhere the antenna cable passes the antenna cable Notel should be directed behind or beside the airbag 5 7 2 Installing the Antenna 1 Thoroughly clean the location intended for installation using a cloth and detergent Allovv the spot to dry before you continue Carefully remove the protective film from the 3M adhesive Locate the antenna on the cleaned location a Carefully press the antenna toward the window Ensure all corners of the antenna are attached to the window Chose the mounting position on the vehicle windshield according to bellow drawing PON Note Please keep min 20 mm distance from metal surface Mount
3. installation begins e Ensure that no wire braids go through locations where Phone accessories are to be installed e Ensure that any parts of the handsfree Phone will not interfere with the vehicle or its accessories operation 4 1 Plan Phone and Cradle Positions The best way to determine the Phone s position to the customer s full satisfaction is to locate it when the customer is beside you and obtain Note his her approval e Please ensure the Phone s location does not interfere with the vehicle or its accessories operation it should not interfere with opening the glove compartment or ashtray should not prevent access to the lighter moving the gear stick operating the hand break etc Do not install the Phone in front of the vehicle s air bag This restriction must be adhered to as in the case of an emergency the air bag blows up Warning and can fail to work properly e Ensure the surface on which this Phone is installed is sufficiently strong to carry the weight and pressure which would be exerted on it e When selecting the Phone s location please ensure the control cable connected to it does not interfere with the vehicle or its accessories operation e Ensure it is safe and convenient to operate the Phone and read the display from the driver s seat e Ensure the Phone would be protected from direct sunlight and humidity air conditioner openings e Ensure the Phone would be protected f
4. Z 8 Telit Telit RoadStar Car Phone Installation Guide Mounting instructions Z 8 Telit Table of Content 1 Carphone KILI u asss swaskasasuakasahaswaqaawwaskasaquakanakuyykiskassshusasqwapawkayykiskassshuskass 2 Installation Diagram siicssssccccssssssecssssscsssosssnessssssecnsssscensssssnecssssseensssscnenassssnesssssnessies 3 Carphone layout i siccccscssccccssssstensssssesssssssecnssssecssssssecsssssceesssssaccssssscecnasssnendsssanessses 4 Preplanned Accessory Positioning 4 1 Plan Phone and Cradle Positions 4 2 Plan the Microphone s Position 4 3 Plan the Speaker s Position 5 Installing the Cradle and Phone 5 1 Where to Position Reminder 5 2 Installing the Cradle and Phone 5 3 Installing the Microphone 5 4 Installing the Speaker 5 5 Installing the Electrical Connections 5 6 Installing the Voltage Cable 5 7 Installing RF Antenna 5 8 Installing GPS Antenna 5 9 Installing the SIM card 6 Trouble Shooting siscsicccsssssvesdisssscossssavestscssccosstensesscosecedesscusesasessccdssansedsesecoasssenes cose f ANPDOMGIK vi u n DS cecedseesesests scsevedscasvdsss s sesscecesssetecceees tecsuestecsavectescevectecess Mounting instructions felit wireless solutions 1 Carphone kit Car phone unit Speaker Microphone Power supply and fuse Cables Cradle wit
5. arts 5 Direct the control cable coming out of the Phone behind the car panel Mounting instructions Telit Installing the Microphone The microphone is provided with a clip which makes it possible to install it inbetween the car roof and windscreen glass 5 3 1 Where to Locate the Microphone Reminder e Install the handsfree Phone s microphone 30 40 cm away from where the driver speaks when he she is in their normal driving position e It is recommended to install the microphone inbetween car roof and windscreen glass and away from external sources of noise e Install the microphone in a different direction than the speaker so as to avoid echo and ensure there is a distance of at least 1 5 meters between them Mounting instructions Teli elit 5 3 2 Installing the Microphone 1 Using the clip install the microphone inbetween the car roof and windscreen glass Direct the microphone cable along the roof behind it so as not to be seen Continue directing the microphone cable along the left beam on the driver side Direct the cable under the dash board to the connection point of the cable with the control cable connected to the Phone Ensure the microphone cable and antenna cable are kept away from each other Note Ensure the microphone cable is not in contact and does not interfere with the car pedals and steering wheel stick 5 Connect the microphone cable plug to the correct port on the cont
6. ashtray should not prevent access to the lighter moving the gear stick operating the hand break etc Do not install the Phone in front of the vehicle s air bag This restriction must be adhered to as in the case of an emergency the air bag blows up Warning and can fail to work properly e Ensure the surface on which this Phone is installed is sufficiently strong to carry the weight and pressure which would be exerted on it e When selecting the Phone s location please ensure the control cable connected to it does not interfere with the vehicle or its accessories operation e Ensure it is safe and convenient to operate the Phone and read the display from the driver s seat Mounting instructions elit e Ensure the Phone would be protected from direct sunlight and humidity air conditioner openings e Ensure the Phone would be protected from mechanical damage by the car s accessories 5 2 Installing the Cradle and Phone 1 Disassemble the cradle into its two parts 2 Install one of the cradle parts in the determined location in the car with 4 tin screws If you are not able to locate the cradle properly please use a adjustable bracket from the station inventory Note 3 Install the second cradle part on the handsfree Phone using the 4 philips screws provided with this kit Only use the original screws provided with this kit Note 4 Connect the two cradle p
7. h screws Mounting instructions 4 e elit er solutions Optional Parts Description RF antenna GPS antenna External Auxiliary Optional Mounting instructions This High Efficiency Omni directional Antennais designed for inside glass mount installations operating in the 800MHz cellular 900 MHz trucking 1800 MHz DCS 1900 MHz PCS and 2100 MHz UMTS bands using included 3M 5M adhesive and supplied with 3M 5M cable and SMA male connector GPSactive antenna Auxiliary is not supplied part of the car kit It s an optional accessories and can be provided separately Z 8 Telit vic 2 Installation Diagram T Swivel PEI Ti Privacy Mount k Handset ua Holder Optional i 4 J gt Head Unit St OF Bak CY Active GPS Antenna Q LD NS N Antenna Speaker E j I j Microphone I Mc I HI Sg 0 Eu 30 IN 27 Zy amp NY IHIN D D lt 2A Fuse Mounting instructions 8 Telit 3 Carphone layout Lett Soft Key OK Send Key for making and accepting calls Voice mail shortcut Mounting instructions Eternal auxiliary Volume Keys Adjust speaker earpiece and ringer volum e 2 2 Display 65k Color wae 5 way Navigation Keys and GPS Right Sott Key End Call Key Keypad Power On Off O Telit 4 Preplanned Accessory Positioning Positioning of all accessories must be planned in advance before
8. ing instructions d Telit 5 7 3 5 7 4 Eo Possible positions Installing the Coaxial Cable Direct the antenna s coaxial cable along the car beam Ensure the antenna cable does not get damaged When completing the cables installation and reaching close to the device coaxial cables SMA female connector attach both connectors together Roll the remaining cable Examine the antenna and cables properly installed Mounting instructions Telit 5 8 1 Installing GPS Antenna Where to Locate the Antenna The preferred location for the antenna is on the bottom right side of the dashboard In vehicles with air bags on the beam where the antenna cable passes the antenna cable Note should be directed behind or beside the airbag 5 8 2 PON 5 8 3 Installing the Antenna Thoroughly clean the location intended for installation using a cloth and detergent Allow the spot to dry before you continue Carefully remove the protective film from the 3M adhesive Locate the antenna on the cleaned location Carefully press the antenna toward the dashborad Ensure all corners of the antenna are attached to the dashboard Possible positions Mounting instructions elit 5 8 4 Installing the Coaxial Cable 5 Direct the antenna s coaxial cable along the car beam Ensure the antenna cable does not get damaged 6 When completing the cables installation and reaching c
9. lose to the device coaxial cables SMA female connector attach both connectors together 7 Rollthe remaining cable 8 Examine the antenna and cables properly installed Mounting instructions Telit Installing the SIM card See SIM card installation position Note Insert the SIM card when the phone is off Mounting instructions Z 8 Telit 6 Trouble Shooting Symptom No reception What to Check Check whether connector is correctly connected to the cable use an efficiency meter What to Do Replace connector Check if internal and external antenna base is correctly attached Attach antenna base Check proper working order of antenna cable Replace antenna cable Other party cannot be properly heard Check speaker s proper working order Replace speaker A Phone problem may exist Replace Phone Check speaker location Change location User is not heard by the other party Check microphone and contacts Tighten microphone connector to the Phone Check routing of microphone cable Change routing of microphone cable Check microphone s proper working order Replace microphone A Phone problem may exist Replace Phone Noise is heard Ask whether noise always occurs in specific geographical areas Explain that reception trouble sometimes occurs in transition between coverage areas Ask whether noise occurs when window is open
10. may damage the wires Warning The value for the fuses provided with the kits must not be changed The kit is appropriate only for a 12V vehicle In case of converting any other kit model into this kit please change the power cable The electrical cables should be directed as follows e So as not to disturb the driver or passengers e So as not to pass near the cars sharp or moving parts 4 The external voltage connection is located under the dash board or close to the fuse box depending on the car model Note In new vehicles a cellular phone connection can be found near the fuse box See the car s user s manual under Info Only use the kit s original fuses 250V 2A Mounting instructions Telit vvireless solutions Installing the Voltage Cable Voltage battery Ignition GND The following chart covers the manner by which the voltage cable should be connected to the cars electrical system Mute Wire Color Red Includes fuse case Function To provide the handsfree Phone with fixed voltage Must be connected to 12V fixed voltage An additional fuse case is provided which must be connected to a fixed voltage source Ensure Ensure a 250V 2A fuse is used Includes fuse case phone after switching the ignition on and turn it off after car ignition is switched off voltage Black To provide a fixed Car body minus
11. rol cable Mounting instructions Telit Installing the Speaker A W 5 4 1 Where to Locate the Speaker Reminder Note Note The speaker and microphone installed inbetween the car roof and windscreen glass above the driver must face different directions If the speaker and microphone face each other this will cause echo Do not hide the speaker inside the dash board If you cover it sound quality will be lowered e Locate the speaker at the right side of the main console at the front of the console in a location where it would not bother the driver or passengers but would sound best 5 4 2 Installing the Speaker 1 Do a de DS Install the speaker at the right side of the main console at the front of the console Disassemble the screws connecting the A speaker to the hanger Ss Install the hanger using the 2 tin screws Direct the speaker cable behind the mat located at the bottom of the car Ensure the cable does not interfere with the vehicle or its accessories operation Ensure the speaker cable is not exposed to damage by the passengers Mounting instructions elit 5 5 Installing the Electrical Connections The electrical cable is provided separately from the control cable Before installation begins connect the four leads which include the 2A fuses using a red or blue crimp sleeve as appropriate Please note sharp edges or moving parts which
12. rom mechanical damage by the cars accessories Mounting instructions elit 4 2 Plan the Microphone s Position e Install the handsfree Phone s microphone 30 40 cm away from where the driver speaks when he she is in their normal driving position e lt is recommended to install the microphone inbetween car roof and windscreen glass and away from external sources of noise e Install the microphone in a different direction than the speaker so as to avoid echo 4 3 Plan the Speaker s Position The speaker and microphone installed inbetween car roof and windscreen glass above the driver must face different directions Note Do not hide the speaker inside the dash board If you cover it sound quality will be lowered Note e Locate the speaker at the right side of the main console at the front of the console in a location where it would not bother the driver or passengers but would sound best Mounting instructions 8 Telit 5 Installing the Cradle and Phone De r Carphone unit Cradle Adjustable bracket 5 1 Where to Position Reminder The best way to determine the Phone s position to the customer s full satisfaction is to locate it vvhen the customer is beside you and obtain Notel his her agreement e Please ensure the Phone s location does not interfere with the vehicle or its accessories operation it should not interfere with opening the glove compartment or
Download Pdf Manuals
Related Search