Home

MTP6550/MTP6750 Product Information Manual

1. Full GCK VN current Full GCK VN GCK version number GCK List list all GCKs stored in the MS that is GCKN and GCK VN attributes e DMO info Direct Mode Operation information RSSI and Frequency 3 4 2 Radio Info Depending on the codeplug configuration the manufacturer type and serial number information is available The information is available through the service page accessible from the MMI The Radio Info provides the following data e Manufacturer e Product Type W muaa The manufacturer and product type information is displayed only on radios distributed under Motorola trademark e ISSI the ISSI which is currently in use If a SIM Card is present the ISSI is read from the card otherwise it is taken from the codeplug TEI the TEI is displayed as a hexadecimal number e Serial number Motorola serial number is displayed only on radios distributed under Motorola trademark e OPTA if the BSI SIM support is disabled no OPTA information is displayed 3 4 3 Hardware Test This mode allows performing basic hardware tests and share the results immediately on the display 3 22 3 4 3 Hardware Test Y muaa The hardware test mode is only for use by authorized persons Use the following key combinations to access the hardware test 1 2 3 hold all simultaneously and then press ON OFF key 3 23 Appendix A Tones A NOTE To listen to the audio signal tones samples refer to t
2. Press to return to the home screen NAVIGATION key Press up down left or right NAVIGATION key for list scrolling while moving around the menu hierarchy or for alphanumeric text editing From the home screen press to activate one of the following Down NAVIGATION key enters Recent Calls menu item Up NAVIGATION key changes My Groups talkgroup folder Left and right NAVIGATION key toggles through the talkgroups BACKLIGHT SENSOR The backlight sensor measures ambient light intensity When the display backlight is active and a low light condition is detected the keypad is illuminated y NOTE A detailed list of compatible accessories is included in Accessory Leaflet part number 68015000668 To obtain the document contact your service provider 3 1 3 Keypad Lock You can lock the keypad to prevent accidental pressing of keys The keypad lock can be invoked using the menu or predefined menu shortcut by default Menu By default while the keypad is locked all front and side keys including PTT are inoperative except for the ON OFF and EMERGENCY buttons The PTT button behavior can be set in the codeplug When an incoming emergency call is received the PTT button automatically unlocks for the call duration When the keypad is locked one of the following is displayed e Nothing no notification is displayed e Notification Only Keys Locked is displayed e Notification and Instruction
3. 2 9 6 Non Selectable Talkgroups A talkgroup can be provisioned as a non selectable talkgroup Such talkgroups are not visible when scrolling through the talkgroup list and thus cannot be selected The group name is displayed only upon receiving a call for the group for instance if it is an announcement talkgroup associated with the selected group or if it is a scanned one TETRA Radio Product Information Manual 2 9 7 Talk Time Limit The radio limits the time you can continuously talk in a group call without interruption according to a provisioned value You are warned a short time before the talk time expires The timer is provisioned per talkgroup folder 2 9 8 Receiving a Group Call In most situations the radio receives group calls without any intervention When the radio receives an incoming group call you may be alerted with a short alert tone Depending on the configuration the tone may be disabled Then the speech follows To clear a call ended by the call owner normally the SwMD you do not need to do anything However you can leave a group call Then the call continues for other radios however your radio does not participate in the call anymore 2 9 9 Talkgroup Scanning 2 8 Talkgroup scanning allows the radio to monitor signaling of a number of talkgroups at the same time In addition to monitoring signaling addressed to the selected talkgroup the radio can monitor signaling addressed to multiple talkgroups T
4. Press Menu and to unlock is displayed The displayed option can be set in the codeplug By default it is set to Notification and Instruction 3 6 3 1 4 Automatic Keypad Lock 3 1 4 Automatic Keypad Lock The automatic keypad lock is a feature enabling the radio to lock its keypad automatically after a defined period The radio allows activating or deactivating the feature using the MMI If the feature is enabled after a defined time of inactivity the keypad locks automatically Any user activity restarts the Automatic Keypad Lock timer When the keypad locks automatically the following notification is displayed Keypad auto locked You can change the time value required for the automatic lock through the MMI 3 1 5 One Touch Button Feature The One Touch Button feature allows for quick activation of functions by pressing and holding keys or buttons assigned to those functions Table 3 3 One Touch Button Features Feature Backlight Toggle Bluetooth Discoverable Mode Change Audio Profile Change Talkgroup Connect Disconnect RSM Earpiece Covert Mode Disconnect All Connected Bluetooth Devices Display Time Enable Disable Howling Suppression Extra Zoom On Off Flashlight On Off Flip Display GPS Report Hi Low Audio Initiate Call Out Fallback Alert PABX Call Phone Call Previous Talkgroup Description Toggles the backlight settings Turns on off the Discoverable Mode Change to the specific audio profil
5. November 2013 D DN d 68015000664 A O 2013 Motorola Solutions Inc All rights reserved Contents UN ae RE 1 1 1 1 MTP6000 Series Overview non r nn R ERRE RR RR nr RR nr nnrnnnnnnnrnnnanennnoss 1 1 1 1 1 Specification MTP6000 Series 1 3 1 2 Radio and Features Ordering Options ocooccooccnocnnnccnnncnononnornnnnnncnnnnrnnnnnnnnrn cece eeseeeeeeeeseeeeeseeeaeeeseneeenenees 1 4 1 3 Dongle Enablement Software Enablement ks 1 5 L Ordering Software Enablement Kit 2 cc ccsseccceccasen deck casei dienei odian eisiaa i ETa coceasdudeccebteevecceatuedeucs 1 6 K Radio Orderin esseen eneen n al iodo 1 6 16 Golden Codeplug usais dias 1 6 2 Services and D 2 1 Sch Peatures OVE Weno aca 2 1 ANS Re re EE 2 2 2 3 Trunked Mode Opera seidtiedregite g deeg tiara tesina ed ege et 2 3 2 4 Direct Mode E e EE 2 3 2 5 Numbering and Addressing oocccoccnoccnocnnncnnnnnonnrnn rn nn RR rr RR RR eeeeeeeeseeeeesaeeseeeaenerenegees 2 4 2 0 Dialing Methods usina 2 4 2 6 1 Talkgroup Dialing nn nn nnrn nr ron rr nr rn nn eae rr nn non ee nnrr nono nnnnrnnnrnnnoninens 2 4 2 6 2 Individual Dialing cita as ice 2 5 2 1 United Address Book inicia 2 5 28 Call HIStory scotland 2 6 2 9 Group Call varias cilindrada 2 6 2 9 1 Programmable Talk proupss 02i ssssescheesssseetensonsnstenseastebossnensssnaseasscaustsnsedstoaresccevensesssansosrnse 2 6 29 2 Talk soup Selection otitis Ee 2 7 2 93 Favorite Folders edi dE Coa diese
6. Talkgroup Dialing The talkgroup dialing by index allows calling from a radio to a talkgroup by using the talkgroup speed dial number in other words the Talkgroup ID or Index By default you scroll through a list of talkgroups to find the one and call With the talkgroup dialing by index option enabled you can use the keypad and enter the talkgroup speed dial number followed by the key For example to call a talkgroup which ID is 19 a radio user enters 1 9 and from the keypad and then presses the PTT button 2 6 2 Individual Dialing 2 6 2 Individual Dialing If the One Touch Button method is provisioned you can call an individual by pressing and holding down one of the programmable buttons The Phone PABX feature allows you to dial Phone PABX by a shortened number of up to three digits instead of the full number The Phone PABX Speed number is assigned when the dialed number is added in the contact list You can re dial numbers from the call history stack The private ID number is a number with up to 16 digits If you enter less than 16 digits the Individual Short Subscriber Identity ISSI part is padded to full Individual TETRA Subscriber Identity ITSI with leading zeros The private ID number consists of MCC Mobile Country Code MNC Mobile Network Code and ISSI Table 2 1 Dialing Scheme MCC MNC ISSI 16 14 13 9 8 1 Y Hua For the MNC of a private ID digits 13 9 values from 00000 to 16383 are accepted Two
7. A NOTE See the following section Charging Battery Solid red Blinking red Solid orange Blinking orange No indication Status In use Repeating call Battery fully charged In service Battery charged at 90 Out of service Rapid charge Trickle charge Connecting to the network Entering DMO Faulty or invalid battery Transmit inhibit in service Channel busy in DMO Incoming call Battery is waiting to charge Idle Radio powered down 3 1 TETRA Radio Product Information Manual Charging Battery When you charge your radio in a multi unit charger and the battery is at the 90 100 charge level the LED indicators on the radio and on the multi unit charger differ LED on the radio blinking green LED on the multi unit charger solid green Y muaa It is possible to charge the battery by means of the USB cable only after installing the special driver available on the CPS CD Make sure that Motorola Customer Programming Software CPS or the USB Charging Driver Tool available on the CPS installation CD is installed on your computer 3 2 3 1 2 Controls and Indicators LA lt A I N D ant 8 Zi bo 3 1 2 Controls and Indi
8. Digital Fingerprint feature is enabled you can also add comments or edit exiting ones The Picture Browser has two views e The multi picture view displays thumbnails of pictures and folders e The full screen view displays one picture that is scaled to fit the display This view also allows zooming in and out of pictures Picture Browser displays pictures only in the JPEG format that is files with jpg and peg extensions Also the browser does not open pictures which size exceeds 10 MB File too large message is displayed 2 29 3 Digital Fingerprint A Digital Fingerprint is a unique signature generated and assigned to each picture after it is taken It allows authenticating pictures taken by Motorola radios so that they can be used as supporting evidence for example in a court of law The existing Digital Fingerprint cannot be modified or overwritten by another one The Digital Fingerprints are stored in the internal radio memory and cannot be accessed by end users Extracting and administering the pictures together with their signatures is later done by using of a Motorola application iTM PICS The radio can contain up to 1000 items If no space for the signatures is left the pictures are still captured and stored but without generating Digital Fingerprints Upon Terminal Permanent Disable all picture signatures are optionally deleted Y muaa This is a selling feature 2 29 4 EXIF Data EXIF data EXchan
9. Service Information Telephone Numbers and Addresses of Latin America Radio Support Centers Country Telephone Number Address Colombia 571 376 6990 MOTOROLA DE COLOMBIA SERVICE CENTRE Torre Banco Ganadero Carrera 7 No 71 52 Torre B piso 13 Oficina 1301 Bogota Mexico 5252576700 MOTOROLA DE MEXICO SERVICE CENTRE Bosques de Alisos 125 Col Bosques de las Lomas CP 05120 Mexico DF Piece Parts To order parts in Latin America and the Caribbean contact your local Motorola CGISS representative xvil TETRA Radio Product Information Manual Service Information Telephone Numbers and Addresses of Latin America Motorola Centers Country Telephone Number Address Argentina 5411 4317 5300 MOTOROLA DE ARGENTINA Ave del Libertador 1855 B1638BGE Vicente Lopez Buenos Aires Brasil 5511 3847 668 MOTOROLA DO BRASIL LTDA Av Chedid Jafet 222 Bloco D Conjuntos 11 12 21 22 E 41 Condominio Millennium Office Park 04551 065 Vila Olimpia Sao Paulo Chile 562 338 9000 MOTOROLA CHILE Ave Nueva Tajamar 481 Edif World Trade Center Of 1702 Torre Norte Las Condes Santiago Colombia 571 376 6990 MOTOROLA DE COLOMBIA LTDA Carrera 7 71 52 Torre A Oficina 1301 Bogot Costa Rica 506 201 1480 MOTOROLA DE COSTA RICA Parque Empresarial Plaza Roble Edificio El Portico ler Piso Centro de Negocios Internacional Guachepelin Escazu San Jose Ecuador 5932 264 1627 MOTOROLA DEL ECUADOR Autopist Gral Rumi ahui Puente 2 Conjunto Puerta del S
10. TXI Mode Activate In this mode the radio does not transmit under any circumstances except for the Emergency Calls All the functions and keys which cause transmission for example registration to the network changing talkgroup or folder sending SDS messages or pressing the PTT button are disabled Any transmission trial causes the radio to display Not Allowed In TXI Mode notification and to play a tone Your radio can still receive e Group calls e Messages stored in the Inbox e Private call attempts stored in the Missed Calls list without the option to respond When no danger to safety exists anymore for example you leave the RF sensitive area you can deactivate the Transmit Inhibit Mode and the radio returns to standard operation You can deactivate the mode by selecting MENU Networks TXI Mode Deactivate pressing One Touch button or implicitly when initiating an Emergency Call TETRA Radio Product Information Manual Y muaa RF Transmissions from the radio are prevented under the following conditions TXI Mode is activated e Battery is removed e The radio is turned off On entering or exiting the transmit inhibit mode when the radio is camped on a cell it sends a specially designated SDS status message This SDS message indicates to the SwMI that the radio is entering or exiting transmit inhibit mode Mobility procedures that do not require the radio to send an uplink transmission are
11. referred to as Key Association Ranges KAR are used to convey the TMO talkgroup and GCK relationships to the relevant SwMI and radios responsible for GCK functions 2 14 4 5 Over the Air Rekeying 2 30 TETRA systems support GCK encryption for specific talkgroups e Group Over the Air Rekeying OTAR of GCK Group OTAR of fallback TM SCK e Group OTAR of DM SCK including management of the cryptographic schedule of DM SCKs The group OTAR mechanisms require a use of the group session key for OTAR GSKO The GSKO is delivered to the radio only by using individual OTAR and the session key for OTAR KSO For the systems utilizing group OTAR the fundamental system operation with respect to SCK GCK OTAR relies on the sites regular transmission In other words the sites are regularly broadcasting information regarding which security class and associated keys are in use The sites transmit future versions of the respective keys to groups of radios belonging to the same cryptographic management group CMG The radios acquire the keys before the SwMI activates them Then the air interface encryption service uses the keys The sites also broadcast the current key that is in use which can be sent using OTAR mechanism to the radio on request 7 NOTE When a radio has not received a new key before activation by the SwMI the radio requests the missing keys Some systems adopt only individual OTAR methods for delivery of SCK and GCK to the ra
12. 10 Private Call If the radio receives a SwMI initiated attachment for the group already currently selected the radio accepts the attachment and keeps the group selected If the radio receives a SwMI initiated attachment for a group in the currently active scan list the attachment is accepted If it is for a group that is not in the current active scan list the attachment is rejected If the detachment is for the selected group the display indicates that no group is currently selected If the detachment is for a group that is in the scan list the group remains in the list However 1t is not monitored If the detachment is for a group that is in the SwMI controlled list it is removed from that list 2 10 Private Call The Private Call also called point to point or individual call enables calling between two individuals No other radio can hear the conversation This call type can be carried out in two ways Duplex call if the system allows in TMO Mode Both parties can speak at the same time e Simplex call in TMO or DMO Mode Only one party can speak at a time From your radio a Private Call can be started using one of the following methods e Dialing ISSI number on the idle screen e By selecting contact from the address book e By selecting ISSI number from the recent call list Using Remote Control feature By pressing predefined One Touch Button e Other When a DMO Private Call takes place radios not involved in
13. 14 15 16 17 18 19 Description KEYPAD Use the keypad to enter alphanumeric characters for dialing contact entries and text messages The keys 0 9 and support the One Touch Button feature Press and hold a key to activate a one touch function assigned to it J muaa The required time to press and hold a button to activate a One Touch Button feature is by default set to 1 second BOTTOM MICROPHONE Activated during Duplex low audio calls such as Private Calls BOTTOM CONNECTOR Used for charging and programming the radio and connecting data transfer cables 5 0 megapixel CAMERA with auto focus and LED flash Available only on MTP6750 ANTENNA EXTERNAL ANTENNA CONNECTOR Used to connect an external antenna such as the one in a Digital Car Kit TOP MICROPHONE Activated during Simplex high audio calls such as Group Calls SIDE CONNECTOR Provides connection for accessories Y muaa It is recommended to turn off the radio before connecting accessories DISPLAY Features a high resolution of 240 x 320 pixels and 65 536 colors Supports scalable fonts and high color images MENU key e From the home screen press to enter the main menu e Used to enter context sensitive menus 3 5 TETRA Radio Product Information Manual Table 3 2 Controls and Indicators cont d Annotation 20 21 22 Description ON OFF END HOME key e Press and hold to turn on off your radio e Press to end calls
14. 5 Accessory Setup Y muaa When volume control capable Bluetooth device is connected the radio always uses the Common setting The max volume offset dB and the volume range dB are configurable via CPS Audio Settings gt User Profile The volume control in the radio is divided into 13 steps 0 to 14 if e g the vol range is set to 39 each step on the volume indication bar is 3dB 3 3 5 Accessory Setup When connecting an accessory to the radio s side connector if it is an IMPRES accessory the radio detects and recognizes the accessory automatically Else if the accessory is CORE Other i e 3rd party accessory detected by specific resistance values or Secondary Accessory i e an earpiece connected to RSM the radio may detect the connection however the accessory has to be set manually via the Accry Setup menu or CPS Audio Settings This menu contains the supported accessories represented by their Model Number as defined by the related ADD Audio Device Descriptor ADD is a set of parameters in the radio which defines the audio setting e g gains and filters settings for each accessory For Motorola accessories the ADDs are predefined and cannot be changed by the user For 3rd party accessories the ADD parameters are configurable via CPS Audio Settings gt 3rd Party Accessory Device Parameter please refer to the licensable Motorola 3rd Audio Device Descriptor ADD parameter creation for 3rd party audio acc
15. EAN Time Time Time Time Time Latitude 2 Letter Code 1 Letter Code 3 Letter Code 3 Letter Code and 2 Letter Code Longitude Easting and Easting and Easting and Easting and Northing Coordinate Northing Coordinate Northing Coordinate Northing Coordinate Altitude Altitude Altitude Altitude Altitude Satellites Satellites Satellites Satellites Satellites e Time indicates when the last time the location was calculated The time is provided in Universal Time Coordinated e Letter Code grid zone or square on the map for different coordinate standard e Latitude expressed in degrees minutes and seconds e Longitude expressed in degrees minutes and seconds e Number of satellites used to calculate the location In general more satellites make for better accuracy The maximum is 12 satellites e Easting refers to the eastward measured distance expressed in meters e Northing refers to the northward measured distance expressed in meters 2 59 TETRA Radio Product Information Manual Y muaa Skipping each digit of easting and northing coordinates decreases the accuracy by the factor of 10 2 26 Side Connector The radio is equipped with a side connector allowing to attach accessories like RSM Remote Speaker Microphone head sets earpieces 2 27 WAP Wireless Application Protocol WAP is a standard for application layer network communications in a wireless communication environment such as
16. ENEE giles 2 27 2 13 9 SDS Receive Failure Notfceaton rr nnnrrnrrnnnrnnnrnnninninnns 2 27 DANA SEU e et e o e e a ac 2 27 2 14 1 Terminal Equipment Identity cocina al caia cee 2 27 214 2 PIN PUK User Authentication cirios REESEN 2 27 214 3 Eeer 2 27 2 14 4 Air Interface Ee NOO tt ninaa 2 28 2 14 41 Cleat Radios Class dla A e dae ean bebo id 2 29 2 14 4 2 Static Cipher Key Encryption Class 21 2 29 2 14 4 3 Derived Cipher Key and Common Cipher Keys Encryption Class 21 2 29 2 14 4 4 Group Cipher Keys Encryption Class 201 2 29 2 14 4 5 Over the Air Rekeying 0 cece cece cece ence e eee ence ence ee e e Ea AET E EE AAAI A N ENANA 2 30 2 14 4 6 Encryption Mobil tous each ad clea e Oe aa as ed gee AS ed eign Se Aaen 2 31 2 14 47 Encryption MMI eech ee aere Eed e d eeh bebe dd eet 2 31 214 48 ALE EE 2 31 2 14 4 9 Deleting User Keys cil idad 2 31 ZAS Secure DMO siii EE 2 32 2 14 6 End to End Encryption ici a ia cee 2 32 2 14 9 Radio Disable Enable 2 2 tinai eerie EE 2 33 21478 Radio Permanent Disable A sio 2 34 2 14 9 Radio Permanent Disable vi 2 34 2 14 10 High Assurance Booty its atleta els 2 35 ZAS Packet RE 2 35 ZISA Voice and Data SUP 2 36 215 2 Packet Data IP Addressing ees AE 2 38 215 3 PD User Authentication EE 2 38 216 TETRA Network Protocol Mutis A A ewe BEERS 2 38 2 16 1 TNP1 IP Addressing ee ENEE occa a ic 2 39 ZAP MObilityServies a tie 2 39 2 17 1 Main Control Channel Frequen
17. Messaging System Flow Model 2 55 Push Hramew ik usais iaa 2 61 Default Home Screen With Icons cecceece cece cece cece ee ence eeeeeeeeeeeceeeeeeeeaeeeeeseeeseeeseseeaeeeseneeenenees 3 9 List of Tables Table 1 1 Table 1 2 Table 1 3 Table 2 1 Table 2 2 Table 2 3 Table 2 4 Table 2 5 Table 2 6 Table 2 7 Table 3 1 Table 3 2 Table 3 3 Table 3 4 Table 3 5 Table 3 6 Table 3 7 Table A 1 Service Information Telephone Numbers to EIA Integrated Call Center xi Service Information Telephone Numbers and Addresses of the Asia and Pacific Motorola UEL e xiii Service Information Telephone Numbers and Addresses of Latin America Radio Support Co E E A A E E ias xvii Service Information Telephone Numbers and Addresses of Latin America Motorola Centers xviii General Technical Specification sinere erene E eee RATE EE EEE E E E Dee 1 3 RF Specifications usan s ie s EEE de a EEE EESE EE dia 1 4 GPS Specification vseen ea sear A AE A So a AE E E EAE 1 4 Dialing en 2 5 Security Features Required Per Security Class ccccceecceeccceeceeeeeeeece eee eeseeeeeeeeeeeseeeaeeaeeeennenees 2 28 Voice Data Interaction Mode ege rice deta EEES 2 37 Packet Data IP Address ME aint lira tabasco Rieger 2 38 TNPI IP AA nets paanneedeieeeibede gare A E AEE ASTE EE EAE 2 39 GPS Trig Bers iia dd EEEE E EE EEEE EE laestes che 2 57 Different Location Displays oocooccooccnnonnononocnnncconccnnnonononononn eee
18. OTAR Over The Air Re keying Preemptive Priority Call Secondary Control Channel SwMI Initiated Authentication Talkgroup and Priority monitor Temporary Permanently Enable Disable Transmit Inhibit RF Sensitive Area Mode Direct Mode Operation DMO AT commands DMO Group Call DMO Group Emergency Call DMO Inter MNI including open group and open MNI DMO Repeater Capability DMO Static Key Encryption DMO SCK DMO TMO Emergency Switching Transmit Inhibit RF Sensitive Area Mode 2 1 TETRA Radio Product Information Manual Platform Specific Features Built in GPS receiver Energy Economy Flashing via USB GPS over Multi Slot Packet Data GPS over SDS Man Down Camera Bluetooth Configurable Idle Screen General Features Covert Mode Favorite talkgroups Flexible size talkgroup folders GPS location reports and display High Assurance Boot HAB memory access protection Super groups of scan groups Features Not Supported in Dimetra Background scanning CCK per LA DCK Forwarding SwMI controlled groups SwMI initiated attachments 2 2 System Support 2 2 The radio operates on the Dimetra IP 5 x 6 x 7 x and 8 x releases and Dimetra IP Compact It also operates on previous versions of Dimetra from Release 3 8 and on The radio is designed to operate optimally on the Dimetra IP system The radio operates properly on all SwMIs that comply with the following IOP TIP documents TIP Core TTR 001 01
19. Repeater not available message and the repeater icon is blinking Messages and sounds are configured by the service provider 2 22 SDS Remote Control The SDS remote control feature enables controlling a radio through Air Interface using SDS TL bearer service A controlling terminal for instance a controlling radio or SwMI controlling terminal sends the SDS remote control messages with AT commands to be executed by the radio 2 52 2 23 Call Out Figure 2 6 SDS remote Control Overview Controlled Radio d TMO lt 4 gt SwMI ControllingTerminal TMO DMO Radio TE Controlling Terminal The SDS remote control functionality works in both TMO and DMO and the remote control PDUs are sent using terminal equipment TE You can use the feature only after a successful authorization which requires entering a valid remote control PIN number The remote control messages can be sent to a group or individual radios A controlled radio receives over the air control information using SDS type 4 with TL on the specific PID number defined in the codeplug If the received control message is originated from one of ISSIs present on the radio authorized ISSI list the radio executes received command and sends a response If configured by service provider upon the reception of SDS Remote Control Service AT command request the radio gives an audio visual notification The service provider has two options Limited SDS
20. Speaker Enable Disable Per Call Start Camera Timed Talkgroup Change TMO DMO Switch TMO Talkgroup Scan Toggle Backlight Intensity Toggle RF Power Class Transmit Inhibit Mode TXI Turn On Off Bluetooth Turn On Off Repeater Mode Description Initiates a private call simplex or duplex to a predefined entry in the contact list or to the last group call originator Takes a quick picture no auto focus without starting the camera application The picture is automatically saved to a selected folder Toggles on off RMS feature Locks unlocks the Rotary Switches Asks for the credential or logs off the radio Activates scanning for Bluetooth devices Turns on off the Screen Saver feature Scrolls through all available audio profiles Sends a predefined message to a dedicated address Sends a dedicated status message to a dedicated address Sends a user defined message to a dedicated address Enables the loudspeaker for a duration of the ongoing call Turns on the camera or takes a picture with auto focus if the camera application is already started This is the default function for the upper SIDE button Makes a predefined talkgroup the selected talk group for a specified amount of time While using the predefined talkgroup the second press of the One Touch Button results in returning to the previously selected talkgroup restarting the predefined time or no action depending on configuration After the timer expir
21. TIP Part 1 Core TIP SDS TTR 001 02 TIP Part 2 Short Data Service TIP Auth TTR 001 04 TIP Part 4 Authentication TIP PD TTR 001 05 TIP Part 5 Packet Data TIP SS AL TTR 001 09 TIP Part 9 Ambience Listening TIP AIE TTR 001 11 TIP Part 11 Air Interface Encryption TIP Disable TTR 001 13 TIP Part 13 Enable Disable 2 3 Trunked Mode Operation 2 3 Trunked Mode Operation Trunked Mode Operation requires the switching and management infrastructure This operation mode enables various voice and data communication types for example group calls short data service messages and access to the infrastructure related features for example packet data Figure 2 1 Trunked Mode Operation 2 4 Direct Mode Operation Direct Mode Operation is a mode of simplex operation where radios communicate directly Figure 2 2 Direct Mode Operation 2 3 TETRA Radio Product Information Manual 2 5 Numbering and Addressing Each radio has a TETRA ITSI used for addressing the radio over the air interface However it is undesirable to require you to enter a long number to address another radio To this end a set of short number schemes can be used Alternatively the radio can be provisioned to treat a short number as an SSI This scheme can be refined to allow short dialing within a fleet by combining the ID entered with the radio own SSI If the radio is provisioned to treat a short number as a TETRA Short Subs
22. The test page is only for use by authorized persons When using KVL 3000 a portable device used to load encryption keys to a secure entity set the baud rate on it to 19200 bits second Use the following key sequence to access the test page MENU RIGHT y NOTE If the test page option is not enabled in the codeplug you have only access to the KVL mode options KVL On or KVL Off 3 20 3 4 1 Test Page The following information is available in the test page e Ver Info Version Information displays software hardware version information Build Date software build a compiled version of software CP Ver CodePlug version DSP Ver Signalling Processor Software version Host Ver Application Software version HardwarelD hardware identification number EquipID TEI Tetra Equipment Identity LLS version Local Language Package version Addresses Home MNI country identification code network code Group ID number of the currently selected talkgroup Own ISSI Own Individual Short Subscriber Identity ASSI Alias Short Subscriber Identity Err Logs Error Logs displays information about software errors e Cells Info Cell Information displays information about the foreground and background cells BTS sites This menu displays the RSSI levels of the cells e Cell Lists Displays frequency lists Frequency List1 32 variable f
23. Touch Button Feature ani Eeer ed EE See E d e 3 7 GE D I EE 3 9 E Status AA A Ee ed AEN ee ond ES 3 10 ERR EE 3 15 3 2 3 Conmtigurable Idle Screen it tipa EE 3 16 324 Display Estres A A a A ate 3 16 IDO eanguages UP A colinda era 3 17 O Reels cote eae oc pe T ae Dee a CARS E OLAV RAL EBT AREER PE 3 18 BiB TONGS EE 3 18 3 3 2 Dual Microphonescia AR 3 18 3 3 3 Speaker Entries vale Sec cs vac cue ces van ov dea NENNEN Ga cada wens E E AE ER a 3 18 3 3 4 Volume Adjustment Mode 3 18 3 3 5 Accessory e E EE 3 19 SS MR HE EE 3 19 3 3 6 1 Audio Pro files tii tarda 3 19 3 3 6 2 Transmit Automatic Gain Control oococccocnncnocononoconononcnoconcnocononnconononcnncnnnnncnoroncnnroninoninns 3 20 3 3 6 3 Howling Suppression EE 3 20 e NN 3 20 eh FRESE E RO 3 20 S DEEN e e NS 3 22 34 3 Hardware EE 3 22 ee Mee EE A 1 Appendix B Gloss a dee ee B 1 List of Figures Figure 1 1 Figure 1 2 Figure 2 1 Figure 2 2 Figure 2 3 Figure 2 4 Figure 2 5 Figure 2 6 Figure 2 7 Figure 2 8 Figure 3 1 MIR O nadaa ino 1 1 MTPOT EEN 1 2 Trunked Mode Opera sii ido dede ta dt de dc ii is 2 3 Direct Mode Operati OM secrccececsiesusvecsieassacsctarsantan read e ee deeg deed Sud e 2 3 SDS End to End EncryptiOii sestine ierann EE ee 2 26 Voice and Data End to End Encryption cccccecccececeecceeceeeece cece eeceeeeeeeeeseea seca esse eeeeeeeeeeeeeeeaeegas 2 33 Repeater Mode Operations 2 51 SDS remote Control Overseas 2 53 Radio
24. Unit 1807 1812 18 F Two Harbourfront 22 Tak Fung Street Hunghom Kowloon Hong Kong Contact Judy Leung E mail Judy Leung motorolasolutions com Motorola Communications Philippines Inc Unit 2102 One Global Place Building 5th Ave Bonifacio Global City Taguig Philippines 1634 Contact Arthur Nieves E mail Arthur Nieves motorolasolutions com Motorola Solutions Korea Inc 9th Floor Hibrand Building 215 Yangjae Dong Seocho Gu Seoul 137 924 Korea Contact KS Kwak E mail r45321 motorolasolutions com Motorola Solutions Taiwan Ltd 8F No 9 Songgao Rd Taipei 110 Taiwan R O C Contact Michael Chou E mail ftpe239 motorolasolutions com Motorola Solutions Australia Pty Ltd 10 Wesley Court Tally Ho Business Park East Burwood Victoria 3151 Australia E mail servicecentre au motorolasolutions com XV TETRA Radio Product Information Manual xvi Piece Parts Some replacement parts spare parts and or product information can be ordered directly If a complete Motorola part number is assigned to the part it is available from Motorola Radio Aftermarket and Accessory Division AAD If no part number is assigned the part is not normally available from Motorola If a list of parts is not included that means that no user serviceable parts are available for that kit or assembly Customer Programming Software has no capability to tune the radio Tuning the radio can onl
25. allocated by the national authority that allocates frequency assignments in a country and should be requested from that authority at the same time as frequency allocations are requested The MCC and MNC together form a unique TETRA system identifier that is broadcast by a Dimetra system over the air interface Modified Group Cipher Key Used to encrypt group addressed downlink signaling NGCH Next Generation Control Head OTAR Over The Air Rekeying protocol Over The Air Rekeying protocol OTAR Used in connection with Air Interface Encryption SEE ALSO Air Interface Encryption PABX Private Automatic Branch Exchange PABX Gateway A device that provides connectivity from a TETRA user to a PABX subscriber and the other way around SEE ALSO Private Automatic Branch Exchange PDV2 Permanent Disable Version 2 PEI Peripheral Equipment Interface Permanent Disable Version 2 PDV2 You can restore a disabled radio using CPS Plus Personal Hands Free kit PHF In other words an earpiece or a handset PHF Personal Hands Free kit Private Automatic Branch Exchange PABX Allows to call local office extension numbers Private Call Appendix B Glossary An individual call between two radios or between a radio and a console operator Apart from the two interlocutors no one else can participate or listen to the call Private Duplex Call A private call between two radios that resembles a telephone conversati
26. and 3 are always routed to the PEI when an AT application is registered If no external application is registered the message is discarded y NOTE The DMO SDS do not support type 1 2 and 3 user defined short messages 2 13 7 SDS Encryption 2 24 Short data messages stored in a radio are protected against any unauthorized access The stored data includes messages in the Inbox Outbox and stored call out messages The required protection against any unauthorized access through the MMI PEL or unintentional access by other means is carried out through the special mechanisms The encryption of stored messages preventing from accessing the memory directly and the user authentication protect SDS messages Protected messages cannot be read on the radio MMI unless valid authentication occurs For the user authentication the existing radio PIN is used 2 13 7 1 SDS End to End Encryption SDS messages received by the radio are encrypted before being stored in the Inbox Store and Forward messages are encrypted before being saved in the Outbox Received call out messages are encrypted before being stored in the CO Box If the feature is enabled then the radio prompts you to enter the PIN if any of the following menu items are selected from the MMI e Messages Inbox e Messages Outbox e Messages CO Box Following successful PIN entry and access to the required messages the radio does not require further PIN entries to access m
27. building that uses its own infrastructure When DAIM feature is enabled the user has these selectable options Migrate to In this mode the radio user selects the network manually Once network is selected terminal performs migration as to the foreign SwMI If you change talkgroup to the one from a different network radio automatically migrates to this network Auto In this mode the radio selects the network automatically After migrating the radio is in the Clear Mode AIM DAIM and Any Networks features are mutually exclusive 2 17 9 Any Networks This feature allows to use the radio on any network that was pre configured in that radio like it was its Home network This is useful when the radio loses its Home network coverage but is within coverage of another network for example if a radio travels between different locations Note that calls between networks are not possible y NOTE Air Interface Encryption services are not available when roaming to a different not Home network Dynamic Air Interface Migration and Any Networks features are mutually exclusive This is a selling feature 2 17 10 Congested Cell Handling 2 44 This feature is used only during initial registration and when roaming between sites It is not used when camped on a site that has become busy or congested due to no free traffic channel to make or receive calls When the cell that the terminal is trying to register is congested a special le
28. card as part of Permanent Disable the MS formats the SD card This applies to both Permanent Disable and Permanent Disable v2 Bluetooth You can use Bluetooth to e Connect the radio with wireless accessories for example headsets which gives you a greater freedom of movement and increases your work comfort e Send and receive files via the Object Push Profile OPP The radio supports Bluetooth 2 1 EDR standard Secure Simple Pairing one of its features ensures high level of security while pairing devices and thus protects you against recording and passive eavesdropping Bluetooth operating range is approximately 10 meters The usable range may be reduced if you connect the radio with devices that support more limited ranges or if physical obstacles such as walls appear between devices One radio can be connected with up to three devices at the same time You can connect one Motorola PTT pod one headset and one device supporting file transfer Y muaa Bluetooth and the Object Push Profile are selling features 2 65 TETRA Radio Product Information Manual 2 31 1 Bluetooth Interactions The features and situations provided in the table below limit the use of Bluetooth Transmit Inhibit Mode TXD Bluetooth does not work in the Transmit Inhibit Mode nor in the Repeater Repeater Mode Mode When the radio enters one of those modes while Bluetooth is enabled all remote devices are disconnected and Bluetooth is disabled A
29. due to the location area rejection the radio does not attempt to register again at this cell until the next power on The radio supports the modification of its subscriber class on receipt of a new subscriber class from the SwMI in the registration acknowledgment PDU This subscriber class is used until turning off the radio or next ITSI attach TETRA Radio Product Information Manual The radio does not send registration signaling when one of the following occurs e Roaming and registration fail before the radio receives the random access acknowledgment and the radio goes back to the last serving cell e The radio discovers a link failure on the serving cell the link failure is shorter than the predefined timer and the radio is not in the transmit inhibit mode e The radio discovers a link failure on the serving cell and is in the transmit inhibit mode In this case the radio always goes back to the serving cell without registration and stays in the transmit inhibit mode until the mode is turned off Y muaa When two or more scenarios occur at the same time the radio registers with signaling If the radio discovers a link failure on the serving cell a specific timer starts counting If the link failure remains after the timer expires then the radio acts as during a normal link failure If the link failure ends before timer expires then the radio goes back to the serving cell without registration This mechanism ensures that unnecessary r
30. if supported e Supergroup of the selected talkgroup e Supergroups of the scanned talkgroup 2 9 10 Priority Monitor 2 9 10 Priority Monitor While the radio is active in a group call it may receive a group call setup for a different group The radio decides whether to ignore the new call or accept it basing on the call priority If the new call has the higher priority than the current one the new call may be joined and the current call is dropped The following priority types are applicable to calls e Call priority indicated in the call setup signaling e Priority of the group indicated by the Class of Usage CoU negotiated upon attachment If the old call and new call have different call priorities the radio follows the call with the higher call priority If the calls have the same call priority the CoU priority of the group decides If a radio is in a group call but is not currently the talking party and detects a call setup for a different group with the same priority it joins the call if a CoU priority is higher The radio can be set up not to immediately join the new higher priority call but to present the new call to the user before joining it If so provisioned you are given a choice of following the new higher priority call or staying with the present call The radio can be set up to treat a selected group call as a higher priority than a scan group call This behavior occurs regardless of the priority of the calls o
31. in emergency operation and given time interval after the last location report Periodic Profile expires LRRP only This is a selling feature 2 25 1 GPS over Packet Data This feature enables a radio to use the GPS Location Service over Packet Data instead of standard Short Data Services When the GPS Location Service feature is enabled and the GPS services have been turned on using the radio interface the radio requests for Packet Data context activation With turning off the GPS using the radio interface Packet Data service deactivates The ongoing Packet Data session deregisters For the GPS over Packet Data triggers and location information are sent or received while Packet Data is activated It is carried out similarly to the standard GPS over SDS When the GPS over Packet Data is enabled sending or receiving triggers and location information during DMO or Emergency Mode is not possible If a Packet Data connection cannot be established the radio is not able to send or receive GPS data 2 25 2 GPS Military Grid Reference System 2 58 The Military Grid Reference System MGRS is the geocoordinate standard used by the military for locating points on Earth The MGRS attempts to represent the entire surface of Earth on a worldwide grid The grid is based on the UTM Universe Transverse Mercator between 80 S and 84 N latitudes and UPS Universal Polar Stereographic systems The UTM area is divided into 60 longitudinal strip
32. indicate a stronger signal Direct Mode Displayed when the radio is in Direct Mode radio to radio communication 3 2 1 Status Icons Table 3 6 Status Icons cont d Icon E d Pal General Icons Description Repeater Mode Displayed when the radio is switched to work as a repeater in Repeater Mode DMO Gateway Communication Mode Indicates that gateway is selected The icon has the following states e Solid while the radio is synchronized with the gateway e Blinking while the radio is not synchronized or during attachment e No icon during a radio to radio and repeater call DMO Repeater Communication Mode Displayed when the Repeater or GW Rep option in DMO Mode is selected This icon has the following states e Solid while the radio has detected the repeater for example when the radio receives a presence signal e Blinking while the radio has not detected the repeater or during attachment e No icon during a radio to radio and gateway call All Tones Off and Duplex and Simplex Ring Muted Indicates that all alert tones are off and both duplex an simplex ring volume is set to 0 All Tones Off Indicates that e Volume is set to 0 when Volume Adj Mode is set to Common e Both simplex and duplex ring volume is set to 0 when Volume Adj Mode is set to Individual Simplex Ring Muted Indicates that simplex ring volume is set to 0 and duplex ring volume is
33. internal flash memory or on microSD cards It is possible to share the pictures by Bluetooth they are also accessible via USB In Emergency Operations it is only possible to initialize the camera by One Touch Button To authenticate the photos Digital Fingerprint and EXIF tags are added The camera application adds the following information the picture s EXIF data e GPS position when there is GPS coverage e network information SwMI time stamp the radio ISSI selected GTSI serving site at the time the picture was taken Digital Fingerprint is stored separately Y muaa The feature as well as specific settings connected with it requires to be set up by the service provider 2 29 1 Live View The camera starts in Live view in this mode live preview from camera is displayed on the screen and blended with terminal GUI allowing user to capture a picture To take a picture press Capture The pictures are stored on the SD card or extended flash memory TETRA Radio Product Information Manual While in the live view mode notices requiring your action are displayed and actions selected by you are taken Group calls operate in the background incoming group calls are heard and you can start a group call or answer the existing one by pressing PTT Private calls terminate the live view mode 2 29 2 Pictures The Picture Browser is an application that allows you to browse through pictures taken by the camera Unless the
34. options are given to the user e Fixed provide up to 16 digits which include the MCC MNC and ISSI numbers If you enter less than 16 digits then the rest is filled with the digits that are set in the codeplug e Automatic provide up to eight digits If you provide more it switches to fixed mode If you enter less than 16 digits the radio fills the rest of the number with its own ITSI If you try to enter more than 16 digits you receive a prompt informing about an incorrect input 2 Unified Address Book The radio offers an address book facility where multiple numbers are associated with a single name tag This facility presents an interface to the address book and provides a natural way to call an individual who can be contacted in different ways Each individual can have up to six associated numbers e Private a TETRA ISSI e Home phone number e Mobile phone number e Work phone number PABX local short number e Other phone number The Contact List has a maximum capacity of 1000 Contacts with up to 1000 associated Private and up to 1000 associated either Phone or PABX numbers distributed among the contacts The radio provides editing capabilities to the address book to allow adding or deleting entries TETRA Radio Product Information Manual The radio provides with the possibility to view the number of used and free address book entries The address book is also accessible through PEI Using the PEI e
35. periodically repeats the audible and visible indication of low battery Signal level icon Displayed in TMO at all times Displayed in DMO only when receiving a voice in a group call Up to five lines of text Displays 3 to 4 lines depending upon the font size and the icon bar Line 1 Network status or network identification No Service or MCC MNC or MCC MNC alias Line 2 Selected Group Folder Line 3 Selected Group 4 Lines 4 5 Home Mode Display if available Line 5 Time and Date if available 3 15 TETRA Radio Product Information Manual Y muaa In case the time and date information for a specific language cannot be displayed in one line in the zoom or standard mode the information is displayed in two lines The time and date overwrite the second line of Home Mode Display if any e Softkey labels and optional menu icon An optional wallpaper background From the idle display you have an easy access to stored target lists e Pressing the UP key accesses the favorite talkgroups list e Pressing the DOWN key accesses the recent calls lists e Pressing the SEND key accesses the last dialed numbers list e Pressing the Contacts softkey accesses the address book 3 2 3 Configurable Idle Screen Configurable Idle Screen is a feature that allows your service provider to determine what additional information is displayed below the status icon area on the idle screen five items maximum The following informatio
36. radio notifies when a new status message has been received Upon receiving an incoming status message the stored text corresponding to the status value is extracted and placed in the text message buffer as a text message Receiving a status causes the radio to display the message mail screen allowing the user quick access to read the message A received status can be stored in the radio text message buffer The PEI provides access for external applications to send and receive status messages TETRA Radio Product Information Manual 2 13 2 Text Messages 2 22 The radio supports an internal text messaging application using the TETRA SDS Transport Layer The radio can send and receive up to 140 bytes of payload data which can be up to 160 characters if a 7 bit encoding is used Depending on radio settings for each message in the Inbox the following options are available e Store used to save the message as a template Delete used to remove the message from the list Delete All used to remove all the messages from the list e Reply used to send a reply to the message originator with the option to edit the text where available e Forward used to send the current message to another recipient with the option to edit the text e Refresh used to reorder the messages list and see the newest at the top When you are in the Inbox and the new message comes refresh the list to see the new message The radio provid
37. storing any new incoming or outgoing RMS message overwrites the oldest message received or sent in the RMS Box This is a selling feature 2 25 GPS Location Service The GPS Location Service feature uses information from Global Positioning System GPS satellites orbiting the Earth to determine the approximate geographical location of your radio The GPS Location Service availability accuracy and the position calculation time vary depending on the environment in which you use the radio The GPS Location Service can assist your dispatcher or colleagues in many ways such as more efficient deployment of resources or locating your radio when you trigger your emergency service The radio can display the location information directly on the screen or send it over the air to your Dispatcher to display it in the control center Check your radio configuration details with your service provider A IMPORTANT Where the signals from satellites are not available the GPS Location Service does not work This situation usually happens when your radio cannot establish a view of a wide area of open sky for example when your GPS antenna is covered or facing the ground Such situations include being In underground locations e Inside buildings trains or other covered vehicles Under any other metal or concrete roof or structure e Near a powerful radio or television tower e In extreme temperature outside the operating limits of your radio Eve
38. that the code and data flashed in the radio is authentic and has not been altered The hardware forces the HAB module to run at boot time The module checks if all software comes from a trusted source The radio is checking the signature of the code and data segments present in the radio using a public private key mechanism If the HAB authentication of the flashed software fails it does not allow the radio software to run 2 15 Packet Data The radio provides in the TMO a TETRA bearer service for applications that use the IP protocol This service is available to external applications by connecting using the PEI The radio supports TETRA standard multi slot packet data using the IP network layer protocol through Point to Point Protocol PPP and TETRA SNDCP protocol The IP connection is established between Terminal Equipment and Mobile Terminal allowing external applications to communicate with Terminal Equipment using predefined IP addresses Y muaa This IP connection is referred to as the local link The link established between the radio and the SwMI is referred to as the wide link When a wide link has been established the radio is considered to be in the wide mode Packet data applications reside internally over UDP or in an externally connected device connected via USB cable port in the radio Communication to the external radio is initialized using AT commands Once the connection is established the external application may re
39. the correct SSI and MNI of the radio the radio becomes disabled When disabled the radio does not participate in any voice call SDS or packet data activity and ignores all supplementary services sent on the downlink All visible and audible indications are disabled and the radio appears to be turned off All user inputs key presses knob operation are ignored and the PEI interface is closed The radio continues to perform mobility management functions such as roaming to facilitate subsequent enabling or further disabling The radio stores the disabled enabled state in the codeplug so the unit remains in that state after turning on If the radio is in the disabled state and receives an appropriate TETRA signaling for subscription enablement with the correct SSI and MNI it restores to its normal operative state The TEI Query feature provides TEI information to the infrastructure during registration This allows to disable the radio by sending an appropriate TETRA signaling for equipment disable with the correct TEI for this radio Replacing the SIM card does not activate the radio TETRA Radio Product Information Manual If the radio is in the equipment disabled state and receives an appropriate TETRA signaling with the correct TEI the radio restores to its normal operative state if the subscription is also in the enabled state 2 14 8 Radio Permanent Disable Permanent disabling is intended to protect a network from attack
40. used on all networks You can limit registration to the home network only or to a selected network only and to ignore the other allowed networks In case the migration defined by ETSI standard is NOT supported by the BTS multi system operation is only supported as follows You can change the network mode using the MMI A top level menu item called Networks Sel allows choosing between Home Only Select Net and Any Net If the radio chooses a network different from the current one the radio forces initial cell selection to find a cell that belongs to the home or the selected network In the selected network option a list of network names where each network name corresponds to one of the MNIs in the list is displayed The network names are provisioned in the radio as part of provisioning of the MNI list The network alias or MNI of the current network is displayed on the first line of the idle display Home Only In this mode the radio recognizes only the first system in the allowed list As a result the radio registers only on its home network even if a foreign network is in range and is found first Select Network Select Net In this mode the radio recognizes only the system you selected in the list of allowed systems As the result the radio registers only on this selected network even if another network is in range and is found first Any Network Any Net In this mode radio selects the network automatically where the home network is no
41. K vivid colors Backlight Flip screen large icons and scalable text font options Screen saver gif image amp text user defined Universal time display 256 TMO Folders 4000 Entries up to 2048 entries in one folder Class 3L 1 8 W 2048 Unique entries 128 DMO Folders 1024 DMO Groups 384 3 Favorite Groups folders containing up to 128 entries each 1000 Contacts up to six entries numbers per contact Maximum 2000 entries 100 Short and 20 Long Messages for Outbox 100 Short and 10 Long Messages for Inbox 400 Entries 100 Entries 40 Lists of 20 Groups TETRA Radio Product Information Manual Table 1 1 General Technical Specification cont d Parameter Value Operating Temperature C 30 to 60 Storage Temperature C 40 to 85 Humidity ETSI 300 019 1 7 class 7 3E Dust and Water Shock Mechanical Drop amp Vibration Table 1 2 RF Specification Parameter Frequency Bands MHz RF Channel Bandwidth kHz Transmitter RF Output Power W RF Power Control RF Power Level Accuracy dB Adaptive Power Control Receiver Class Receiver Static Sensitivity dBm Receiver Dynamic Sensitivity dBm Table 1 3 GPS Specification Parameter GPS Tracking Sensivity GPS Horizontal Tracking Accuracy tracking 7 NOTE IP67 and IP65 per IEC 60529 ETSI 300 019 1 7 class 7M3 Value 350 470 MHz 25 Power Class 3L 1 8W amp Class 4 1W 3 Steps of 5 dB 2 A and B A and B 114 min 116 typical 105 m
42. Mobile Terminal applications use this address as the source address in IP packets delivered to the infrastructure Local IP Address By default both Terminal Equipment and the radio have their own IP addresses Terminal Equipment and Mobile Terminal use these addresses for local datagram transmissions between Terminal Equipment and Mobile Terminal only and are not passed to the SwMI Static or Dynamic IP Address Assignment The terminals support static and dynamic IP address assignment The dynamic support is requested in the following situations e Request a Dynamic IP Address is set to Dynamic and the PD Application Type is the radio internal PD application Request a Dynamic IP Address is set to Dynamic and the PD Application Type is a PEI PD application requesting dynamic IP address 2 15 3 PD User Authentication The PD user authentication is a method of authenticating the Terminal Equipment user before allowing the packet data link activation A PD Authentication server connected to the SwMI performs the actual authentication The terminal only sends the messages between the Terminal Equipment and the SwMI In the wide mode the terminal offers PPP user authentication between Mobile Terminal and Terminal Equipment using Password Authentication Protocol PAP or Challenge Handshake Authentication Protocol CHAP before the IP link is established The terminal always attempts to negotiate usage of the CHAP method However the radio agre
43. Push Initiator PI to transmit push content and delivery instructions to a Push Proxy Gateway PPG The PPG delivers the push content to the radio as per to the delivery instructions The PI is an application running on a web server and communicating with the PPG using the Push Access Protocol PAP The PPG uses the Push Over The Air OTA Protocol to deliver the push content to the radio Figure 2 8 Push Framework y Push Over the Air Protocol Push Access Protocol E WAP Client Push Proxy Gateway Push Initiator 2 27 2 2 WAP Push Service Indication The service indication SI presents a notification and an associated URL with a prompt to enter the URL on the radio display The notification is then stored in the WAP box for subsequent presentation The SI can be valid only for a certain amount of time After the specified time elapses the Sl indicates void content The author of an SI can set the expiration date and time that is when the SI is automatically deleted from a radio The service provider can remotely delete SIs that became invalid The removal is carried out through sending a special SI to delete the invalid entity A new Sl is indicated with a respective status icon tone and a pop up The pop up occurrence depends on the SI priority high and medium and the radio conditions for instance if the radio is in a call the pop up does not appear Depending on the periodic alert feature availability a notification of an unr
44. RC and Full SDS RC modes The SDS remote control in the Limited SDS RC enables the following e Switching between TMO DMO modes read change notify for individual radio and group using CTOM AT command Selecting a talkgroup read change notify for individual radio and group using CTGS AT command Collecting Network Information from individual radio Network Registration Status and Cell Signal Quality using respectively the CREG and CSQ AT commands e Reading individual radio GPS position using GPSPOS AT command e Setting volume level for individual MT using CLVL AT command The SDS remote control in the Full SDS RC enables to use most of the AT Commands Refer to the AT Commands Programmer s Guide to see which are not supported This is a selling feature 2 23 Call Out A call out is an alert sent to one or many recipients when an incident requires immediate attention The call out message can include an instruction to use a different talkgroup for the duration of the call out or remain on the attached talkgroup TETRA Radio Product Information Manual 2 23 2 54 There are four types of Call Out alerts e Normal e Storm Plan Fallback Mode e Test Call Out Only the emergency mode has higher priority than the call out When you receive the alert the following responses are available e Accept additional information from the dispatcher is displayed e Stand by voice and message communication
45. TETRA network The protocol is used to access the mobile web from a radio through a WAP browser A NOTE This is a selling feature 2 27 1 WAP Browser The Openwave Mobile Browser is a WAP compliant user agent The WAP browser provides all of the basic services of a computer based web browser Whenever any preemptive display interrupts the browser session the browser needs manual reactivating to return The WAP browser does not support right to left languages as Arabic and Hebrew English is used instead For the content in these languages the characters are not displayed J muaa Depending on the radio configuration and the network conditions the WAP browser may not display images properly or may display them with a delay 2 27 2 WAP Push 2 60 WAP push allows WAP content to be pushed to a radio This push is carried out by sending a specially formatted Push Access Protocol XML document to the Push Proxy Gateway that in turn forwards the document to the radio A WAP push message is an encoded message including a link to a WAP address On receiving a WAP push a WAP enabled radio automatically gives the option to access the WAP content The implemented WAP push is compliant to WAP 2 0 standard The radio supports WAP 2 0 through a proxy only Proxy less connections are not supported This is a selling feature 2 27 2 1 WAP Push Framework 2 27 2 1 WAP Push Framework A push operation in WAP is carried out by allowing a
46. TT button When the call ends the radio will exit the Disaster Alert state During Disaster Alert other functionality is impacted e When Disaster Alert begins any other ongoing services are terminated e No other services can interrupt this type of call e Hot Mic functionality cannot be used e Speech can only be in Clear mode even if any of the encryption services are enabled The only exception is E2E Encryption 7 NOTE Not all infrastructures support this feature Please consult with your service provider before enabling this feature 2 13 Short Data Services The radio supports the following Short Data Service SDS message types SDS Status SDS User Defined Data Types 1 2 3 SDS User Defined Data Type 4 with or without SDS Transport Layer SDS TL The feature supports the following addressing modes e Radio to radio e Radio to talkgroup e Radio to external subscriber number gateway address 2 20 2 13 1 Status Messages Y muaa For SDS TL the message can be sent through the service center The radio provides a short data bearer service for both internal and external applications The radio supports SDS TL services which provide end to end acknowledgments delivery report requests and message numbering for SDS user defined data type 4 messages The TL also provides SDS access for applications that do not request these transport layer services however use a Protocol Identifier PI The rad
47. Triggers Trigger Type Power up Power down Emergency condition Periodic Moved TMO ON DMO ON Transmit Inhibit Mode ON Transmit Inhibit Mode OFF Low battery Trigger Event Radio powers up in TMO Radio powers down in TMO Radio enters emergency operations Given time interval after the last location report expires Radio position has changed by at least the distance defined the radio checks the movement from the last known position at an interval Successful registration on entering TMO from DMO Before TMO deregistration and before entering DMO Radio is about to enter TXI Radio has successfully registered after leaving TXI Radio detects its battery level has reached or fallen below the level specified by service provider 2 57 TETRA Radio Product Information Manual Table 2 6 GPS Triggers cont d Trigger Type Trigger Event Loss of GPS Radio detects a loss of GPS for a minimum duration defined by service provider Recovery of GPS Radio detects a recovery of GPS signal for a minimum duration defined by service provider Status entered Radio sends a status defined in the CP for location reporting by pre programming DCK Connected Radio detects that a Car Kit has been connected DCK Disconnected Radio detects that a connected Car Kit has now been disconnected GPS ON Positioning device has been switched ON GPS OFF Positioning device in the radio is about to be switched OFF Emergency Radio is
48. a TETRA terminal tones architecture is highly flexible and allows you to adjust the level of every tone event e g valid key press individually and at the same time to adjust the level of all events associated with a tone category Using the Customer Programming Software CPS tool it is possible to set the level of each event compare with the nominal speech level 20dBm0 that means for a given volume setting a tone may be louder softer or at speech level This option is available both for in idle i e no received or transmitted speech and in call i e during received or transmitted speech For a complete list of tones and audio files refer to the Appendix 3 3 2 Dual Microphones Each radio has two microphones One located at the top of the unit for dispatch simplex operation and the second located on the bottom of the unit for duplex calls 3 3 3 Speaker Earpiece Each radio has an internal speaker for high audio located at the middle of the unit and an internal earpiece for low audio located at the top of the unit The audio can be routed either to the speaker or the earpiece using the Audio Toggle menu and the assigned One Touch Button 3 3 4 Volume Adjustment Mode You can set the volume to Individual or Common When it is set to Individual the volume level for Voice Duplex Simplex Keypad Tones and Call Out can be set per user preferences When set to Common the audio has one setting for all items 3 18 3 3
49. ace When you turn on scanning and then select the scan list the radio sends a group attachment request to attach the scan groups in addition to the selected group Similarly when you select an ATG the radio sends an attachment of the ATG as the selected group along with the attachment of the associated groups as scan groups Ifa group associated with an ATG is selected the radio sends an attachment of the ATG as the selected group and as a scan group The TETRA TIP provides a facility by which the radio can send a status message to the SwMI to turn scanning off and on to save air interface signaling If the radio is provisioned with this option when you turn scanning off the radio sends an appropriate TETRA signaling In this state the radio does not monitor any groups other than the selected group If you then turn scanning on the radio sends an appropriate TETRA signaling and begins monitoring all scanned groups again If the radio is not provisioned with this option you only have an option to deselect the active scan list However you cannot turn off the scanning Deselection of the user scan list causes a group detachment of the scan list groups sent to the SwMI However the radio continues to scan all other groups such as ATG associations 2 9 24 SwMI Initiated Group Attach Detach The SwMI can send a talkgroup attachment to the radio The radio will attach to it even if this talkgroup had not been programmed in the codeplug 2
50. acket data channel Thus these services may be conducted in parallel The radio can operate in one of the voice data interaction modes 2 15 1 Voice and Data Support Table 2 3 Voice Data Interaction Modes Voice Data Interaction Mode Description Voice Only Mode You have the option to select Voice Only mode in which Packet Data service is disabled If an external application attempts to start up in this mode packet data registration for a wide link is rejected If the packet data service is active when this mode is selected the radio deactivates packet data The PEI operates in the local mode only data transfer between TE and MT Data Only Mode You have the option to select Data only mode in which normal voice calls are not permitted Incoming non emergency voice calls are rejected and you cannot initiate non emergency voice calls Incoming and outgoing emergency calls are allowed Voice and Data Mode In Voice and Data mode any voice call activity that occurs during a data session takes priority over the packet data Once a voice call has interrupted the data session the PD session is suspended until the voice activity has ended Then the session is resumed Voice priority mode is the default mode You can choose one of the interaction modes The choice of interaction mode is stored in non volatile memory and remembered at power up In Voice and Data mode if the radio moves to the traffic channel due to the voice service t
51. adio enters this mode when the power off period is shorter than approximately 3 seconds This behavior applies to normal and silent emergency modes The three second period is approximate and determined by the discharge rate of capacitors in the radio The period may last from 3 up to 6 seconds 2 18 4 Preemptive Priority Call If during a call a call setup is received for a call with higher priority than the present call and the new call priority is Preemptive Priority 3 value 14 in the codeplug or Preemptive Priority 4 Emergency 15 the radio disconnects from the present call and joins the new high priority call If the call priority of the new call is Preemptive Priority 1 12 or Preemptive Priority 2 13 depending on configuration the radio either accepts or rejects the new call When the new call is accepted a special tone is played and you are notified of the high priority call When you initiate a private call and you receive a rejection with the reason Called party busy you have the option to interrupt the existing call or initiate a new call However this time the call is initiated with the preemptive priority 2 18 5 Transmit Inhibit Mode The Transmit Inhibit Mode is a mode in which the radio sends no radio transmissions It is recommended to activate the mode in RF sensitive areas for example hospitals airplanes where safety can be jeopardized due to transmission radiation To activate select MENU Networks
52. aling addressed to the temporary group when the radio initiates a group call on the selected group and the SwMI assigns the call to a temporary group The radio supports assignment of an incoming group call to a temporary group address 2 9 22 Late Entry The user can join the group call even if not participating in it from the beginning This is possible for example if a user turns on their TETRA terminal in such a case the system diverts the user s terminal to a talkgroup call if a call is already in progress Similarly if the user s terminal has been outside of the radio coverage for example in a tunnel the control channel will also divert the user s terminal to a talkgroup call assuming a call is already in progress Y muaa For TMO this feature must be configured on SwMI Acknowledged late entry and late entry paging are not supported 2 9 23 User Initiated Group Attachment To enable a radio to use a group the radio should attach the group The radio initiates a group attachment request to the SwMI after the RCU initialization The attachment occurs whenever you initiate a group change and when the radio registers on a new site When you change the selected talkgroup the radio initiates an attachment to the SwML detaching the old group and attaching the new one All group attachments sent by the radio are sent with attachment mode of Amendment or Detach all depending on which form causes sending less bits over the air interf
53. all without interruption according to a provisioned value You are warned a short time before the talk time expires 2 10 4 Call Restoration in Private Call If the radio roams while you are the transmitting party in a private call the announced cell reselection is employed if possible Call restoration procedures are performed in the new cell If you are not the transmitting party the unannounced cell reselection is employed followed by call restoration procedures 2 10 5 Call Modification Call Modification is a feature that allows your service provider to modify the call in order to optimize it and adjust to a current situation Modification can cover e Call priority modified during call setup e Call type modified during call setup e Call encryption modified during an ongoing call but not in the transmission phase When the call is modified your radio displays Call Modified message When a recently modified call requires the PTT button to transmit your radio displays Call ModifiedUse PTT All modifications are made by your service provider and the radio only follows them You have no influence on ongoing call modifications When call priority is changed to emergency e The display indicates that an Emergency Group Call has been received e The radio plays a special audio alert Y muaa If a Group Call is modified into an Emergency Group Call no emergency related features are triggered If call mod
54. alls and data on a given frequency The repeater sends presence signal periodically on a free channel to allow other radios to synchronize on a given frequency The communication between radios and the DMO repeater is logically divided in two links The term master link is used for all communication taking place between the Master radio and the DMO repeater The term slave link is used for all communication taking place between slave radio and the DMO repeater The master is the radio initiating and transmitting the voice or data and the slave is the radio receiving the voice or data You can enable Call Monitoring of ongoing call to hear what is being transmitted You can enable Interactive Repeater in order to hear and take part in the transmitted call For more information refer to 2 21 DMO Gateway and Repeater Communication page 2 51 This is a selling feature DMO Gateway and Repeater Communication The radio provides the capability of communicating in DMO mode with a TMO group via the IOP certified gateways A DMO repeater re transmits information received from one DMO radio to other DMO radios over the DMO air interface For each DMO talkgroup the radio allows operating in one of the following modes Radio to radio only The radio initiates calls only on a talkgroup directly and not through a gateway or repeater Specific gateway The radio can initiate calls on a talkgroup directly or through a specific gateway ad
55. an E2E terminator located in the infrastructure decrypts the data E2EE protects the SDS SDS TL data services both in TMO and DMO The following TETRA data types are protected SDS type 4 with SDS TL SDS type 4 without TL For short data applications the source data may come from an external application or from a task internal to the radio such as text messages or GPS The radio passes only the internal text messages and GPS data for encryption by its crypto engine TETRA Radio Product Information Manual 2 26 The encrypted short data service is established between two end points One end point is terminated in the radio and the other end point is terminated in a Short Data Encryption Gateway SDEG or another radio The destination address specifies the encryption type that is whether the packets are transmitted as encrypted clear or dropped Figure 2 3 SDS End to End Encryption TETRA System Boundary Message Display Service and Other Embedded Aplications Short Data Transport Layer with or without SDS TL Short Data Service Type 4 Standard TETRA Air Interface Encryption and Key Management y NOTE Key Management Facility KMF can manage and support only one short data association and a key at the same time The radio selects the E2EE mode for the outgoing text message in accordance to the address association and requirements for the E2EE High Security Mode Depending on codeplug setti
56. are received before the timer expires the whole sending process is considered as failed The value of the timer is set by the service provider 2 13 3 Immediate Text Messages Immediate Text Messaging is a selling feature which enables displaying the text message immediately on the radio display This feature is used for sending high important information from the console to radios When the radio has the feature enabled and receives an immediate text message then e the immediate text message is stored in the Inbox e the content of the immediate text message is displayed e the relevant audio tone is played e additionally if the periodic alert feature is enabled the periodic alerting is active until the immediate text message is skipped or closed 7 NOTE When the feature is disabled in the radio then immediate text messages are processed as normal text messages When you reply or forwards an immediate text message the message is sent as a normal text message S 2 23 TETRA Radio Product Information Manual When the radio receives more than one immediate text message then just the latest received immediate message is displayed All the previous immediate messages in the Inbox are not prompted 2 13 4 Home Display Text Message Your radio is provided with a feature that allows your service provider to send special text messages to the display The message stays on the home screen until a new message is received Power cycle y
57. ast Call begins any other ongoing services are terminated TETRA Radio Product Information Manual Y muaa If the type of the encryption is defined by the BSI feature radio with a SIM Card the Broadcast Call is always clear Otherwise 1f the radio uses other encryption service the type of the encryption used for that Call is up to the encryption settings of that service 7 NOTE Not all infrastructures support this feature Consult with your service provider before enabling this feature 2 9 13 Broadcast Call This kind of call enables dispatcher to transmit to all radios in the specific area The radio joins calls received with a communication type broadcast and displays a notification that this call is a broadcast call Typically this call type is addressed to the broadcast address ISSI A broadcast call takes precedence over any other call that has the same or lower call priority 7 NOTE The radio cannot initiate a broadcast call however the radio is able to initiate the broadcast type call restricted to the particular talkgroup using the Announcement Call feature 2 9 14 Announcement Call This feature allows you to make a Broadcast Call from the radio initiated on the predefined talkgroup The alias message displayed during Broadcast Call as well as the call priority and destination address talkgroup can be configured in codeplug This feature can only be used in TMO mode During Announcement Call other feat
58. cation Information Protocol Local Site Trunking LST Allows radio subscribers of the same cell site to communicate when the link between the site and network central controller fails Entering and exiting Local Site Trunking that is returning to Site Wide Trunking is done automatically the display shows the Local Area Service message Any call in progress is dropped upon entering Local Site Trunking mode Registration Group Call and Emergency Call are available in Local Site Trunking SEE ALSO Central Network Equipment Location Request Response Protocol LRPP This protocol allows for a single and efficient format of passing location information requests and responses TETRA Radio Product Information Manual LRPP Location Request Response Protocol LST Local Site Trunking MACE Motorola Advanced Crypto Engine Main Control Channel MCCH The main control channel at a site The channel is used by radios to register on the system and to request and setup speech calls with other radios SEE ALSO Control Channel Man Machine Interface MMI Relates to the CPS Plus and radios user interface MCCH Main Control Channel MLE Mobile Link Entity SEE ALSO Announced Cell Reselection MMI Man Machine Interface Mobile Country Code The MCC and MNC together form a unique TETRA system identifier that is broadcast by a Dimetra system over the air interface Mobile Network Code The Mobile Network Code should be
59. cators TETRA Radio Product Information Manual 3 4 Table 3 2 Controls and Indicators Annotation 1 Description EMERGENCY button Press and hold the EMERGENCY button to start Emergency Operations By default when your radio is off press and hold to power on in Emergency Operations ROTARY KNOB e Rotate to set the volume e Press and rotate to select a different talkgroup e Press and hold the ROTARY KNOB to lock unlock it Powering the radio off and on also unlocks a locked ROTARY KNOB LED Status Indicator EARPIECE Programmable SIDE buttons The SIDE buttons support the One Touch Button feature By default the following features are assigned to them e MTP6550 the upper SIDE button is set to Flip Display and the lower SIDE button is set to High Low Audio e MTP6750 the upper SIDE button is set to Start Camera Take Picture and the lower SIDE button is set to High Low Audio Y muaa The required time to press and hold a button to activate a One Touch Button feature is by default set to 0 1 second PTT Push To Talk e Press and hold to talk in simplex calls release it to listen SOFT key Press left or right SOFT key to select the option that appears above SEND key e Press to initiate or answer duplex calls or send messages e Press in home screen to enter Recent Dialed Calls SPEAKER 3 1 2 Controls and Indicators Table 3 2 Controls and Indicators cont d Annotation 10 11 12 13
60. ceive and send RMS messages ensure that the RMS feature is enabled in the codeplug The radio accepts received RMS messages only from the calling party address defined in the codeplug Any outgoing RMS status is sent to the RMS status target address defined in the codeplug The RMS status is a bidirectional messaging from the control room to a radio and conversely Sending an RMS status is possible where the RMS mode is enabled in the radio In such case the radio user can send one of ten predefined RMS statuses to an address predefined in the codeplug You can select the particular RMS status using assigned one touch buttons A received RMS status is displayed in blue color on the idle display The latest received or sent RMS status is kept on the idle display until the next power cycle The RMS free text is a unidirectional message from the control room to a radio Received RMS free texts are displayed in blue color on the idle display The latest RMS free text is kept on the display idle display until the next power cycle Upon receiving the request the radio sends the latest sent RMS status to the control room without any user interaction or notification z 2 55 TETRA Radio Product Information Manual Incoming and outgoing RMS statuses and RMS free text messages with the exception for RMS status sent are stored in the RMS Box The RMS Box capacity is maximum ten entries for incoming and outgoing RMS messages If the RMS Box is full
61. cies rr nnnrrnrrnnnnnnnrnnninnanns 2 40 217 2 Control Channel Select ii ii 2 40 217 3 MultiSystem Operation A A anses 2 40 2 104 REM A EE lena 2 41 DITS EE EE 2 42 2 17 6 Seamless Hi ars 2 43 QAP Air Interface AA O 2 43 2 17 8 Dynamic Air Interface Migration ooccoocncocnnocnnncnnncnnnncnnnnnnnnnnornncrnnnnnnnrnnnr rn essa eeseeeeaneeeeeeeeeneegas 2 43 ZAR VAny Networks a dl ltda de 2 44 217 10 Congested Cell Handle A A ASS 2 44 A E SEA A e 2 45 217 12 Subscriber Class by Talkgro p ia bdo 2 45 2 17 13 RF Power TE 2 45 2 17 14 Cell Surveillance and Monitoring Threshold Negative C A 2 46 2 18 Supplemenitary OEV E S e A aia EEE 2 46 SSC Ambience ASEO A A ticos 2 46 218 2 Pseudo Power Di ii A a E es 2 46 ES Auto E E EE 2 47 2 18 4 Preemptive Priority Call A ART 2 47 2 18 5 Transmit Inhibit Mode a a iia es 2 47 2 18 6 Calling Line Identification Presentation ccecceeeceeeceeeece cece ee ceeeeeeceeeeee essa esse eeeeneeneeeeeeneegas 2 48 2 18 7 Talking Party Identification Set eege A vet van cadens cheated EES 2 48 221828 RA RE EE 2 49 218 9 Universal Time Dis placita 2 49 219 MANDO A A A EE EA 2 49 2 19 1 Man Down Operation 2 50 220 RE Mod ee EE ed ieee 2 50 2 21 DMO Gateway and Repeater Communication 2 51 2 21 1 Communication through Repeaters nn nnnrnnrrnnnnnnnrnnnnnnanns 2 52 2 22 SDS Remote Control ita A ld At a AE iaa 2 52 A A EE 2 53 2 23 1 Call Qut Interaction
62. cluster where the K REF association has not been deleted Radio Permanent Disable and Radio Permanent Disable v2 are mutually exclusive selling features 2 14 9 Radio Permanent Disable v2 Similarly to the permanent disable once the radio is disabled using the permanent disable v2 it cannot be recovered over the air When the radio accepts the permanent disable command and if the permanent disable v2 flag is enabled in the codeplug the radio appears to be inoperable e All its MMI interfaces on the radio appear to be disabled e All its security key material GCK GSKO DMO SCKs Ks DCK CCK TMO SCKs and End to End key material are deleted e The radio automatically turns off on powering attempts without any audible visible indications to the end users e The permanent disable flag is set in the codeplug Unlike in the permanent disable a permanent disabled v2 radio can be re enabled using the software selling dongle If you have the software selling dongle you can read the codeplug and clear the permanent disable flag 2 14 10 High Assurance Boot Y muaa When a radio has been disabled using the permanent disable v2 entering programming mode procedure is different For the details see TETRA Terminals CPS Start up User Guide Motorola Part Number 6802974C 10 Radio Permanent Disable and Radio Permanent Disable v2 are mutually exclusive selling features 2 14 10 High Assurance Boot The radio has a facility that ensures
63. cording to the terminal settings Book on Reject the radio rejects all the book on Book on Accept the radio accepts all the book on To log off use the radio menu The dispatcher has also the option to log you off using Force Off setting The pseudo log on is a state which occurs when the RUA RUI authenticated radio goes to LST or infrastructure accepts the logon with the empty granted assignment period In this state the radio has the full functionality available except some services as forwarding calls This state is signalized with a specific icon The RUA RUI feature is specified with the following timers Logon Process Timer defines the amount of time during which the radio awaits log on response from infrastructure Time Out Warning Timer defines the amount of time after which the radio displays the warning Logon Period Timer defines the amount of time during which the radio is logged on 2 28 3 RUA RUI Interactions 2 62 When you switch from TMO to DMO the terminal logs off depending on the codeplug settings When you switch from DMO to TMO the radio initiates the log on process 2 29 Camera You may be RUI authenticated when out of coverage In this situation the radio is in pseudo logged on status All the timers are the same as for the logged on user with the coverage You may also be logged off when out of coverage In this situation the radio is provided with the limited service access In b
64. criber Identity SSI and the number entered is less than seven digits the radio own identity is combined with the number entered to produce the actual ISSI Using this scheme an ISSI can be comprised of a fleet number part and a member part The radio own ISSI is used for determining the leading digits for the digits omitted as in the following scenario 1 The radio has the following ID 1234567 2 You enter 890 3 The SSI sent is 1234890 The following services can use the short SSI for identification for both the called and the calling party e Duplex private call e Simplex private call e Group call e Mobile status e Short data bearer service e Text message service Regardless of the short addressing scheme used if you are provisioned with the capability of entering a real TETRA ISSI and you enter an ID of seven digits the number is interpreted as a real TETRA ISSI 2 6 Dialing Methods 2 6 1 2 4 The radio supports multiple methods for selecting a number for an outgoing call The direct dialing provides the radio user with a possibility to dial a number before entering the mode modeless operation for all types of calls To start dialing from the idle display activate the private number dialing editor by pressing and holding an assigned key The default call type is suggested with the possibility to change the call type Scrolling keys are used to scroll back and forth through the contact list or talkgroup folder names
65. dio In such cases GSKO is not used Some systems employ a mix of individual and group OTAR methods The radio supports the complement to functionality required for supporting the superset of different SwMI behaviors for example e Individual OTAR using KSO of SCK and GCK Group OTAR using GSKO of SCK and GCK e Individual OTAR using KSO of GSKO e Secure DMO Key Management via SwMD e Crypto Management Group Storage of 10 KAG equivalent to 30 DM SCK Storage of 16 GCK includes current future versions Storage of 2 TM SCK Storage of Group Association attribute per Talkgroup e GCK Air Interface Encryption e Seamless key changes of GCK e Seamless security class changes to SC3G 2 14 4 6 Encryption Mobility The SwMI can support the group OTAR feature Where supported the SwMI groups radios that share the same set of cryptographic key material into a specific crypto management group CMG Any radio belonging to the same CMG is addressed using a CMG GTSI The primary purpose of the addressing is to transmit group OTAR messages conveying TM SCK DM SCK and or GCK Any radio that supports TM SCK group OTAR DM SCK group OTAR or GCK group OTAR is assigned to a specific CMG Each CMG has a designated specific GSKO The system deploys over the air a CMG GSKO and CMG GTSJ to each radio belonging to the CMG The GSKO is used as the sealing key for TM SCK DM SCK and GCK when sent across the air interface The SwMI ca
66. dness standards the MTP6000 radio guarantees the improved operational effectiveness by e SMP camera and Digital Fingerprint technology to capture and authenticate photographic evidence and intelligence e Micro SD card for multimedia content storage not available on Option board models used for hardware based End to End encryption e Bluetooth v2 1 wireless technology for instant data sharing e TEDS data connectivity for enhanced data transfer hardware ready 1 1 1 Specification MTP6000 Series 1 1 1 Specification MTP6000 Series Value Table 1 1 General Technical Specification Parameter Camera Additional Storage Battery Options Dimensions HxWxD mm Weight g Battery Operating Life Time Expected Tx Rx Stand by 05 05 90 05 35 60 Color Display Talkgroups TMO Talkgroups DMO Favorite Groups Contact List Text Message List Status List Country Code Network Code List Scan List 5MP Auto Focus Built in LED Flash Micro SD card up to 32 GB additional capacity J muaa Micro SD card slot is not available on models that support hardware based End to End Encryption Standard battery 1650 mAh High capacity battery 2150 mAh 132x54x33 5 with standard battery 132x54x36 7 with high capacity battery 286 1 SIM Non camera radio with standard battery and short stubby 380 MHz antenna Class 4 1 W gt 16 hr gt 15 hr gt 12 hr gt 11 hr Large 2 QVGA with 262
67. dress private or MS ISDN During this kind of call all user indications are unavailable and all other services are rejected Emergency Operation ends as soon as the Emergency Individual Call is ended TETRA Radio Product Information Manual 2 12 4 Emergency Alarm The emergency alarm is a special status message sent to the infrastructure while starting the Emergency Operations The radio may wait for infrastructure acknowledgment for this alarm and attempts retries Each time the radio enters the Emergency operation it sends an emergency alarm When an emergency alarm is sent successfully the respective audible tone sounds In addition once the radio is in the Emergency Operation on pressing the EMERGENCY button an additional emergency alarm is sent Exception during Hot Microphone transmission The message can be dispatched both in TMO and DMO 2 12 5 Emergency SDS Status Radio sends a status message with a preprogrammed value to the destination address set up in the codeplug Emergency SDS Status is available in TMO only If no status acknowledgment or negative acknowledgment is received the radio retries sending the message Status is not resend if Emergency Alarm or Hot Microphone is configured 2 12 6 Emergency Hot Microphone The Hot Microphone allows you to talk without pressing the PTT button during Emergency Operations The transmission continues for a provisioned amount of time Pressing the PTT button before the Hot Mic
68. dress that is specified for a talkgroup The gateway address can be edited through the radio MMI 2 51 TETRA Radio Product Information Manual Auto gateway The radio can initiate calls on the selected talkgroup directly with another radio or through any available gateway that is detected as present The talkgroup links to a DMO repeater Specific gateway and repeater The radio uses only the gateway with the specified gateway address for the talkgroup and or a DMO repeater Automatic gateway and The radio uses the first available gateway for a talkgroup and or a DMO repeater repeater If either specific gateway or auto gateway mode is chosen and a suitable gateway is found all outgoing calls are placed through the gateway If a suitable gateway is not found or a call setup through the gateway fails the radio attempts to set up the call directly When operating on a gateway and or repeater the radio indicates the communication mode 2 21 1 Communication through Repeaters Radios that are out of range and cannot communicate directly one with another in DMO Mode can do it through the repeater The repeater is a radio that repeats all communication on a chosen channel and as a result increases radios DMO range DMO DMO When the radio connects to a repeater it plays a tone displays the Repeater available message and shows an appropriate icon When the radio looses connection with the repeater it plays a tone displays the
69. e Changes the talkgroup to the programmed one by your service provider Toggles between operation of RSM with and RSM without earpiece connected Turns on off the Covert Mode Disconnects all Bluetooth devices connected to the radio Displays universal time on the home screen Turns on off Howling Suppression Turns on off Extra Zoom Turns on off the camera flashlight which allows you to use the radio as a torch The flashlight turns off automatically after a period of time determined by your service provider Rotates the display by 180 degrees Disabled if the camera is running This is the default function for the upper SIDE button Sends a message with the radio s GPS location to a dedicated address Toggles high low audio This is the default function for the lower SIDE button Sends Call Out Fallback Alert Initiates a PABX call to a predefined entry in the contact list Initiates a phone call to a predefined entry in the contact list Changes the selected talkgroup of the radio to the talkgroup DMO or TMO that was selected previously 3 7 TETRA Radio Product Information Manual Table 3 3 One Touch Button Features cont d 3 8 Feature Private Call Quick Photo RMS Mode applicable only for and Rotary Switches Lock Unlock RUA RUI Log On Off Scan for Bluetooth Devices Screen Saver Activation Scroll Audio Profiles Sending Predefined Message Sending Status Sending User Defined Message
70. e following e Twenty four hour and twelve hour formats e DD MM Y Y MM DD YY DD MON YY and YY MM DD date formats You can change the time and configuration information through the MMI depending on the codeplug settings Depending on configuration system broadcast information can have higher priority than data entered manually Thus time date and offset information entered from the MMI is overwritten when data is received from the SwMI The radio provides user indications upon crossing to another time zone when a new MCC broadcast received 2 19 Man Down Man Down alerts when no movement occurs for a set time or the radio stays at an angle of tilt below a defined value The radio alerts you when e its tilt exceeds a predefined angle value e it remains static for a predefined time In case any of the above conditions are met the radio alerts you with a Man Down pre alert If you do not remove the pre alert condition the radio switches to the Emergency Operation To exit Man Down exit the Emergency Mode by pressing and holding the Exit SOFT key or press the PTT button TETRA Radio Product Information Manual Y muaa This is a selling feature 2 19 1 Man Down Operation Man Down can be disabled or enabled from the menu or by OTB If the man down feature is deactivated with a One Touch Button the radio plays an audio tone once If the feature is deactivated using the menu the radio does not play the tone The man do
71. e has been decrypted and is now unprotected until it is transmitted out to the caller 2 14 7 Radio Disable Enable Figure 2 4 Voice and Data End to End Encryption TETRA System Boundary Standard TETRA Air Interface Encryption and Key Management Short Data Service Type 4 The End to End Encryption E2EE feature resolves this issue by encrypting the voice information before it is packed into the PDU This message is also encrypted according to the over the air encryption of the TETRA standard Thus when the base station decrypts the PDU containing voice information the voice part remains protected by encryption until the called radio receives the voice and decrypts it The Motorola Advanced Crypto Engine MACE located in the radio carries out voice encryption The crypto engine takes the voice stream and encrypts this stream using a set of keys Likewise the crypto engine takes encrypted voice stream and using the same keys decrypts back into clear voice In the end to end encryption feature the radio notifies and informs whether the call being made or received is voice encrypted The radio also provides with means to select a different key delete keys request new keys and change the encryption mode of nondefined private calls This feature is relevant for group calls and private calls in TMO and DMO 2 14 7 Radio Disable Enable On reception of an appropriate TETRA signaling for subscription disable with
72. ead SI can be indicated with periodic notification similarly to an SDS message 2 27 2 3 WAP Push Service Load Service Loads SL differ from the Service Indications SI by the fact they do not prompt to enter the URL Instead the browser is automatically activated The SL contains an URL indicating what service to load A new SL is indicated with a respective status icon tone and browser activation The browser activation depends on the SL priority high and the radio conditions for instance if the radio is in a call the browser does not display SL messages sent with urgency cache can be not indicated directly to the user Such SL messages load content and store it in the cache the process works in the background only the PD icon is visible to the user 2 28 Radio User Assignment and Radio User Identity Radio User Assignment RUA and Radio User Identity RUI enables authentication for providing full access to the infrastructure and the physical radio Where the RUI feature is enabled on logging on to the radio you enter your User ID with the PIN to check your identity Only the successful logon provides the full access A logon failure results in limited service TETRA Radio Product Information Manual Where also the RUA feature is enabled after successful RUA RUI authentication you are logged on to the physical radio Thus you can still be reached at your radio number You can differentiate the RUA RUI state by the inte
73. eee sea ee nor ae i e a 2 59 LED In diGatins siaii oeer nee een iones 3 1 Controls dnd Indicators E 3 4 One Touch Button Featlles cocteles cerda n e Eeee aah EEEE EEEE E KEENE EEEE E ENES 3 7 Display ai 3 9 Colors of the SOFT Rucci arar aa a A a e a aa ase i Se 3 9 Status cons id add 3 10 Languages Supported WEE 3 17 Radio TOmGS tanda A 1 vii Copyright Information The Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other mediums Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs but not limited to including the exclusive right to copy or reproduce in any form the copyrighted computer program Accordingly any copyrighted Motorola computer programs contained in the Motorola products described in this manual may not be copied reproduced modified reverse engineered or distributed in any manner without the express written permission of Motorola O 2013 Motorola Solutions Inc All rights reserved No part of this manual may be reproduced transmitted stored in a retrieval system or translated into any language or computer language in any form or by any means without the prior written permission of Motorola Solutions Inc Furthermore the purchase of Motorola products shall not be deemed to grant either directly or by implication estoppel or otherwise any license under
74. egistration is avoided When a radio is out of the serving cell range for a period shorter than configured in the codeplug then the radio does not perform the registration on going back in the range 2 17 5 Roaming 2 42 The radio continually monitors neighbor cells and scans the highest ranked neighbor cell When the state of the highest ranked neighbor cell is sufficiently better than the serving cell or when the radio has lost the serving cell the radio employs cell reselection procedures using the following methods e If not in a call undeclared cell reselection e Ifin a call and not transmitting or link failure occurs unannounced cell reselection e If transmitting in a call and a neighbor has been scanned and the cells are synchronized announced type 1 or type 2 cell reselection If transmitting in a call and no neighbor has been scanned or the cells are not synchronized announced type 3 cell reselection For compatibility with systems that do not support type 1 or type 2 cell reselection the radio can be provisioned to never perform these types of reselections The radio decides on the need for cell reselection based on comparison of the signal strength and the service level between the serving cell and neighbor cells The service level criteria are based on the following criteria listed in priority order System Wide Services available Local Wide Trunking Valid Invalid Subscriber Class Relinquishing cr
75. election to another network is only performed at initial cell selection following a link fail and then only if the home network is not available The radio uses Visiting Short Subscriber Identity VSSI AIM DAIM and Any Networks features are mutually exclusive This is a selling feature 2 17 8 Dynamic Air Interface Migration The Dynamic Air Interface Migration feature offers users a quick and easy way to switch between networks Depending on that setting every time a radio is powered up or a talkgroup is changed it automatically roams to the assigned network If a talkgroup has no particular network assigned the radio stays on the current network TETRA Radio Product Information Manual This feature consist of these major functionalities It allows your radio to dynamically select the appropriate network after your radio is powered up e If you change talkgroup to the one from a different network radio automatically migrates to this network in this feature it is possible to assign network to particular talkgroup in the codeplug It gives you an option to automatically migrate to a network which is available in the region network needs to be first pre configured in the codeplug It is useful in case of loosing signal from dynamically selected network as the radio attempts to establish communication with any available network This feature is useful where quick switching between networks is required for example when entering a
76. ementary Services are not supported However identification presentation functionality is supported in most cases using the information found in the call setup messages 2 9 18 Call Ownership The radio can be given the call ownership of a talkgroup call When the radio is the call owner 1t sends an appropriate TETRA signaling to end the call Y muaa The SwMI decides about the ownership of a call 2 9 19 Transmission During Group Call While receiving a group call and the PTT during received Group Call is enabled you may request to transmit by pressing and holding the PTT The system registers this action and informs you that the request has been queued If you release the PTT the radio sends a message to the system withdrawing the request 2 9 20 Call Restoration If the radio roams to a new cell during a call it attempts to continue the call on the new cell Cell reselection and call restoration procedures are employed for this attempt If the radio roams while being the transmitting party in the call an announced cell reselection if possible is carried out in the new cell If the radio is not the transmitting party an unannounced cell reselection is employed followed by call restoration procedures TETRA Radio Product Information Manual 2 9 21 Temporary Group Address The radio supports the temporary group address assigned by the SwMI The address is valid only for the lifetime of the call The radio monitors sign
77. erage and placed together to multiply traffic capacity a number of radios is attached to Talkgroup 1 on the first cell and only one radio is attached to Talkgroup 1 on the second cell A group call uses two traffic channels one on the first cell and one on the second In this scenario multiplying traffic capacity would not work without the feature However as radios on the same talkgroup are forced by Subscriber Class mismatch to roam to one cell all the radios should use only the first cell Spreading radios population across cells and prohibit them from roaming Many radios used on a small area with multiple BTS coverage causes huge roaming traffic A congestion occurs and as a result you would not be able to communicate However with the feature radios do not roam to a cell with mismatched Subscriber Class what stops the roaming traffic A radio Subscriber Class changes when the user changes between talkgroups which are assigned to another Subscriber Class Up to 16 Subscriber Classes can be configured in the CPS and talkgroups assigned to them The assignment is carried out by talkgroup GSSI or by folder except Favorite which the talkgroup was chosen from Talkgroup may be assigned to more than one Subscriber Class either by folder or Talkgroup range The first assigned Subscriber Class is used Upon receiving Subscriber Class from the SwMI radios change their Subscriber Class to the received one The Subscriber Class received from t
78. es the radio returns to the previously selected talkgroup Toggles between TMO and DMO modes Turns on off the Talkgroup Scan feature in TMO Mode Regulates the backlight intensity Toggles the RF Power Class between High and Normal Turns on off the Transmit Inhibit Mode Turns on off Bluetooth Turns on off the Repeater Mode Your service provider can assign one touch functions only to the side buttons and keypad keys 7 NOTE All the features can be assigned on the option buttons for RSM accessories If the One Touch Button feature is enabled the One Touch Dial is disabled If no feature is assigned to a button your radio displays an Unassigned Button message 3 2 Display This section presents the radio s default home screen elements Figure 3 1 Default Home Screen with Icons Folder 1 Test G0000 Table 3 4 Display Annotation 1 2 3 4 The color of the SOFT keys informs you about the mode or state that your radio is in Description Status icon area Text display area SOFT key area MENU Context sensitive icon Table 3 5 Colors of the SOFT Keys Color Light blue Light red Olive Yellow Red Green Blue Grey Mode or State Normal TMO and DMO Modes Emergency Mode or Disaster Alert Call Local Site Trunking Mode Call Out Standby Call Out Alert Call Out Accepted Radio Messaging Service RMS Radio User Assignment RUA Limited service 3 2 Display 3 9 TETRA Rad
79. es an edit facility for composing and editing a text message The message can be sent to a target TETRA radio using SSI addressing and is sent with a request for a received delivery report All the outgoing text messages short or long are stored in Outbox when the store and forward mechanism is not in place When the store and forward feature is enabled and the messages go through the store and forward server the short messages are stored regardless the delivery status Whereas long messages are stored only if delivered even if only to the store and forward server Depending on radio settings for each Outbox message the following options are available e Store used to save the message as a template e Delete used to remove the message from the list e Delete All used to remove all the messages from the list e Resend used to send the message again to the same recipients with the option to edit the text Forward used to send the message to the other recipient with the option to edit the text e Refresh used to reorder the messages list and see the newest at the top e Delivery Status used to check the time and the date when a message was sent delivered read expired or not delivered Every status change is communicated Delivery report is saved in the Inbox and in the associated message in Outbox However the report is deleted from the Inbox after viewing it Outbox and Inbox share memory area hence the
80. es to use PAP when the Terminal Equipment application insists If the terminal does not require PD user authentication it operates without any user authentication However if the terminal requires the PD user authentication it rejects the Packet Data Protocol PDP context activation 7 NOTE If the SwMI does not agree for the authentication method for example PAP the SwMI can reject it 2 16 TETRA Network Protocol 1 TETRA Network Protocol type 1 TNP1 is a bridge protocol based on the TETRA layer 3 over the air protocol The TNP1 supports all TETRA dispatch functionality 2 38 2 16 1 TNP1 IP Addressing In the TMO the TNP1 specifies a protocol for use over the PEI that allows terminal equipment TE to have control over the TETRA services mobility management call control short data service and supplementary services send GPS reports software information and battery state information In addition commands to access the radio configuration and storage parameters are available The radio supports TETRA standard packet data using the IP network layer protocol The radio can operate both on the single slot packet data channel and the multi slot packet data channel Packet data applications reside internally for example GPS reports WAP or in an external device connected to the H wire RS232 data port on the radio Communication to the external device is initialized using AT commands The system provides point to point IP co
81. essages unless one of the following conditions has been met Exiting from the radio menu Turning off the radio Changing the PIN from the MMI If you disable the PIN lock through the MMI or change the PIN the protected messages are deleted Before deleting the messages you are prompted to ensure that the operation should proceed If the PIN lock is changed through the PEI all the protected messages stored in the Inbox Outbox and CO Box are deleted On enabling the radio permanent disable the access to the protected messages is lost 2 13 7 1 SDS End to End Encryption The TETRA standard supports the air interface security that provides protection of the air interface The information flow inside the infrastructure is not secured When you require data protection for your data going through the infrastructure you need your entire transport path to be encrypted This entire path encryption is called end to end encryption E2EE The source and the destinations are supplied with the mechanism for encrypting and decrypting E2EE is a selling feature which provides customers with a higher degree of confidentiality than existing TETRA air interface data encryption Y NOTE The 260 275 MHz radios do not support the SDS end to end encryption In air interface encryption the receiving base station decrypts data which travels clear within the system domain For E2EE the transmitting radio encrypts the data and the receiving radio or
82. essed O 3 14 Non formatted SD Card Solid The microSD card is Not formatted at all Formatted incorrectly or Damaged e Blinking The microSD card is being formatted USB Connected Indicates that the radio is connected to the computer via the USB cable Visible only in the Mass Storage mode Bluetooth Connected Indicates one of the following e Bluetooth is enabled and at least one device is connected e The file transfer is in progress and the radio is either receiving or sending a file 3 2 2 Idle Display Table 3 6 Status Icons cont d Icon Description Bluetooth Disconnected Solid indicates that Bluetooth is enabled but no device is connected Blinking indicates one of the following Bluetooth is enabled and the radio is in the Discoverable Mode e Bluetooth is enabled and a connection with a remote device is being established Remote Control Indicates that the radio is being remotely controlled and some commands are being executed in the background For example when the radio is controlled via special SDS messages or triggered to send a GPS location report The icon is not visible in the Extra Zoom Mode 3 2 2 Idle Display The terminals provide access to all services from the main idle display The idle display shows the following content e Icons on the status area top line Status icons Battery level displayed at all times Y muaa The terminal
83. ession If an application attempts to negotiate data compression during context activation it is rejected If a data compressed IP packet is received from the SwMI it is silently discarded The radio supports IP header compression negotiation received from Terminal Equipment during PDP context activation and transparently transfers IP packets with the header compression between Terminal Equipment and the SwMI The packet data service employs the TETRA standard cell selection and re selection The packet data service is suspended while the reselection is occurring and resumes when the cell reselection procedure is complete Y muaa The cell reselection is undeclared in a strict TETRA sense However the SNDCP protocol defines a procedure for reconnecting the packet data service on the new cell In this sense the cell reselection procedure resembles the unannounced cell re selection procedure Multi slot packet data is a selling feature 2 15 1 Voice and Data Support 2 36 The radio can alternate voice and packet data service However voice and data running in parallel are not supported This behavior corresponds to Packet Data Type B IP dual mode If the SwMI rejects the context activation due to PD MS type not supported the radio reinitiates context activation indicating that supports Type C It is done to accommodate legacy SwMIs that uses an older definition of these types The radio supports transmitting and receiving SDS on the p
84. essories document Motorola ADDs can be imported and removed via CPS Buttons Keys and Accessories gt ADD Import Remove 3 3 6 Audio Features There are many situations where the demand of audio quality changes according to the working environment For example an airport worker who works partly in the field where there is lots of noise coming from the surrounding environment and partly inside the airport where there is relatively less noise may experience different audio quality In the working environments like these ones there is a need for different audio quality and adaptive audio parameters which can be configured according to the working environment 3 3 6 1 Audio Profiles Audio profiles can be used to adjust the audio settings of the radio to fit to different operating environments The user can select the corresponding audio profiles which are mapped to User Profiles generated in CPS It is possible to enable and customize up to 3 audio profiles using CPS Audio Settings gt User Profile The following parameters can be changed in a User Profile e Mic Gain offsets e Howling Gains e AGC Echo Canceller and RX TX Noise suppressor e Voice offsets and ranges for different audio devices Tone offset and ranges y NOTE Audio Profile names in the Radio MMI correspond to the Profile Alias Name parameter value for the corresponding User Profile in CPS TETRA Radio Product Information Manual Using the CPS you ca
85. f retries has been reached The control room terminates the Silent Ambience Listening The Ambience Listening is disconnected due to another reason 2 19 TETRA Radio Product Information Manual If you turn off the radio in the Silent Emergency Mode the radio switches to pseudo power off state In this state the radio appears to be turned off However the radio is still on and in the Silent Emergency Mode On turning the radio on during the pseudo power off state the radio acts as during turning on and still is in the Silent Emergency Mode 2 12 9 Invisible Emergency It is possible for the service provider to disable visual and audible indications of performing Emergency Operations on the radio The purpose of this feature is to hide the fact of using Emergency Operations in a critical situation e g direct attack on the user and thus to provide additional layer of safety 2 12 10 Disaster Alert Disaster Alert call is a broadcast emergency call initiated by the radio with emergency pre emptive priority that everyone in a broadcast area can hear This feature is specifically designed for catastrophic situations such as earthquakes and has the highest priority over other calls All radios under Disaster Alert display emergency notification on their screens The alert message its duration and destination talkgroup can be configured in the codeplug In order to initiate Disaster Alert switch the radio to Disaster Alert mode and press P
86. fic radio models SSI Short Subscriber Identity Static Cipher Key SCK Key used for encryption between radios and BTS in Class 2 systems with corresponding algorithm SEE ALSO Encryption Status ID A feature that makes it possible for a subscriber to send status messages to other subscribers The user can enter a status message for each ID in a Status ID list When a subscriber sends a status message the ID of the subscriber s unit is sent along with the status message Subscriber Identity Module SIM A smart card that holds subscriber information including the authentication key and is inserted into the radio to grant its personality Appendix B Glossary Switching and Management Infrastructure SwMI All the system components excluding the mobile equipment that is the CNE and all the remote site equipment SEE ALSO Central Network Equipment SwMI Switching and Management Infrastructure Talkgroup A group of radio users that can share calls and messages as a group Normally a talkgroup is comprised of users who have a need to communicate with each other on a day to day basis TEI TETRA Equipment Identity Telephone Interconnect TI A call feature that provides subscriber access to the Public Switched Telephone Network PSTN Telephone interconnect can be used for both land to mobile calls and mobile to land calls SEE ALSO Public Switched Telephone Network TETRA Acronym for TErrestrial Trunked RAdio T
87. from a compromised or faulty radio It can be used when the radio has been compromised or has been suspected of compromise for a long time It is a one way function and no equivalent enable is available Then the radio should be recovered and reprogrammed before being used again by the service provider When the radio is permanently disabled it becomes inoperable e All its MMI interfaces on the radio are disabled e All its security key material that is GCK GSKO DMO SCKs Ks DCK CCK TMO SCKs are deleted All its codeplug is deleted e All its software is deleted The permanent disable should be invoked when it has been determined that a radio is unrecoverable When a radio has been lost or stolen the first step always is to stun the radio using the temporary disable The permanent disable should be used with the deletion of the user radio record in the User Configuration Server and the deletion of the K REF association of the disabled radio in the Provisioning Centre and the Authentication Centre This deletion ensures that subscriber information is not downloaded into the Home Location Register if a restore of the UCS is performed The system operator has to also ensure that the radio K REF association is also removed from the other Authentication Centres in the network in cases where the K REF pairs are duplicated across the network If this association is not removed the radio could be assigned a new home zone that lies in a
88. fter leaving the TXI or the Repeater Mode Bluetooth is enabled again provided that it was previously turned on Covert Mode The radio cannot enter Discoverable Mode while in the Covert Mode the Covert Mode has a higher priority Wired Audio Accessories Wired audio accessories have a higher priority than Bluetooth audio accessories If both types of devices are connected to the radio it disconnects the Bluetooth audio device When a wired audio device is already connected to the radio scanning for Bluetooth audio devices is disabled 2 31 2 Bluetooth Restrictions Tetra Radios support simultaneous connection with up to 3 remote devices of different types The Tetra radios do have the following restrictions on the combinations of connected remote devices at any given time e It is only possible to connect one Motorola PTT device connected at a time e It is only possible to connect one Bluetooth BT audio device at a time e It is only possible to have one Object Push Profile OPP enabled device connected at a time The size limit of the file to be sent is 2 GB It is possible to have one Motorola PTT device one BT audio device and one OPP device connected and active at the same time 2 66 3 Man Machine Interface 3 1 Controls Indicators and Related Features 3 1 1 LED Indications Table 3 1 LED Indications Indication Solid green Y muaa See the following section Charging Battery Blinking green
89. geable Image File Format contain technical information about the pictures stored as metadata Motorola radios also store information about the state of the radio at the time the picture was taken such as e Full time and date of taking the picture e GPS position when there is GPS coverage e Radio ISSI e Selected Talkgroup e Servicing Site ID EXIF data cannot be viewed on the radio An EXIF viewer is needed to access the TETRA specific information 2 29 5 Support Light 2 29 5 Support Light The built in LED can be used as a flashlight This functionality must be assigned to a one touch button It is not possible to activate the flashlight from the menu 2 30 Radio Mass Storage 2 31 Radio Mass Storage enables support of Micro SD SDHC Card or flash memory in the MS as a medium for storage for applications The radio can support one of the microSD cards e Micro Secure Digital Card a standard microSD card with capacity up to 2 GB e Micro Secure Digital High Capacity Card MicroSDHC card with capacity from 2 GB to 32 GB The SD Card radio internal flash memory is accessible by the USB interface on the bottom connector The following operations are available to applications Read file e Write file e Create file e Delete file e Create directory e Delete directory If the MS supports an SD card then the SD card is used as message storage device radio internal flash memory is not accessible If the radio supports SD
90. hannel The following types of control channels are available e Main Control Channel MCCH occupies the first slot of the main carrier e Secondary Control Channel SCCH can be used to extend Control Channel capacity The following types of SCCH are available Common SCCH e Assigned SCCH In addition to the MCCH a cell can have up to three common SCCHs which could occupy slots 2 3 and 4 in the main carrier This solution provides the ability to distribute the radio population among up to four channels and so to increase Control Channel capacity at the expense of traffic channel capacity Until having received a specific parameter on a cell the radio uses the MCCH When the signal is received each radio maps itself to a particular common SCCH and that SCCH operates as the MCCH for the radio SCCH is a selling feature 2 17 3 Multi System Operation 2 40 The radio holds a list of up to 100 allowed network identities Mobile Country Code MCC Mobile Network Code MNC combinations that are considered friendly networks The first network in this list must be the radio home network Each network can have an associated name that can indicate to the user which network it is The radio can perform initial cell selection and registration on these networks and only these networks Registration 2 17 4 Registration on any of these networks is performed using the radio ISSI and without migration signaling The same ISSI is
91. he PDF file with the embedded sound files Table A 1 New Tone KJO Radio Tones Classic Tone Gi OG Tone Description Default Beep Played when pressing a key Duplex Volume Set Played when adjusting duplex volume Invalid Action Examples e Pressing an invalid key e Dialing an invalid number e Talk prohibit System Notification Examples e The radio changed its status from out of range to in service e The radio returned to the home network e Toggling between the TMO and DMO modes System Error Examples The radio changed its status from in service to out of range e Call disconnected General Notification Examples e Entering Local Site Trunking e Entering the Transmit Inhibit Mode Positive Notification Message sending succeeded Negative Notification Message sending failed Item Received A new message received Feature User Guide Table A 1 Radio Tones cont d New Tone GIULIA Classic Tone O O O O O Tone Description Talk Permit The radio user is allowed to transmit their message after pressing the PTT button Clear to send Data transmission ready to begin Emergency The Emergency Call received Low Battery The battery charge level is low Over the Air 1 Single D PTT tone Over the Air 2 Double D PTT tone Over the Air 3 Triple D PTT tone Phone Busy The called rad
92. he SwMI over the air has always higher priority than Subscriber Class by Group Ifa radio already uses the same Subscriber Class as the one received from the SwMI the current Subscriber Class is not changed On powering on the radio is set to the default Subscriber Class or Subscriber Class assigned to an attached talkgroup Favorite folders cannot be assigned to any Subscriber Class Super Groups are treated as scanned groups and Subscriber Class by Talkgroup feature does not apply to them Subscriber Class by Talkgroup is a selling feature 2 17 13 RF Power Toggle The RF power toggle is a radio specific hardware feature enabling the radio to transmit with Class 3L 1 8 W power Using the CPS the power class can be set for the radio to transmit with Class 3L 1 8 W or Class 4 S 2 45 TETRA Radio Product Information Manual Depending on the codeplug settings you can toggle through the interface between high and normal RF power That respectively is Class 3L 1 8 W and Class 4 The radio can be configured to switch automatically to Class 3L 1 8 W on entering DMO and to automatically switch to Class 4 1 W on entering TMO Changing RF power class is performed immediately The change can be done for example during a call Such action may result in dropping the call as the selected power class setting can be insufficient to sustain the transmission 2 17 14 Cell Surveillance and Monitoring Threshold Negative C The radio con
93. he digital trunked radio standard produced by ETSI providing detailed telecommunications specifications to which Base Stations and radios should adhere SEE ALSO Base Station European Telecommunications Standards Institute Radio TETRA Equipment Identity TED An electronic serial number that is permanently embedded in the TETRA equipment like radios TI Telephone Interconnect TMO Trunked Mode Operation Trunked Trunked Radio Communications TETRA Radio Product Information Manual Trunked Radio Communications Trunked A computer controlled communications system that allocates speech channels on demand selecting on a random basis from the group of channels available Upgrade To replace radio firmware with a newer version and preserve User and Sensitive Data User Data A set of codeplug nodes and values that can be edited and replicated to other codeplugs or radios VASSI Visitor Alias Short Subscriber Identity
94. he radio terminates any active packet data transmission or reception The data service is suspended The data service resumes when the voice service ends The radio accepts any downlink SDS message received on the Packet Data Control Channel PDCH The radio can send uplink SDS messages on the PDCH The radio allows PEI GPS and WAP PD applications to activate and use the PD context simultaneously The first application initiates PD context activation The next PD context activation from another PD application results in sending a reply indicating that the PD context is active When WAP GPS and PEI PD applications are using the active PD context the radio can filter the downlink IP packets based on their TCP UDP port UDP packets addressed to the WAP port configured in the codeplug are routed to the WAP internal application e UDP packets addressed to the GPS port configured in the codeplug are routed to the GPS internal application e UDP packets not addressed to the WAP nor the GPS ports are routed to the PEI using PPP Y muaa When activating another PD context on the radio use the same settings in both PD contexts 2 37 TETRA Radio Product Information Manual 2 15 2 Packet Data IP Addressing Table 2 4 Packet Data IP Addressing Addressing Mode Description Wide IP Address An IP address may be assigned to the terminal by the SwMI during the Packet Data context activation When assigned both Terminal Equipment and
95. icate that the ROTARY KNOB is in list scrolling mode New Message Has Arrived Indicates a new message just arrived New Message s in Inbox Indicates that you have unread messages in your Inbox Unread New WAP Message Indicates that new page was loaded to the browser Man Down Active Indicates that the Man Down feature is active Man Down Alert Displayed when the Man Down feature is active This icon has two states e Blinking pre Alert the radio signalizes Man Down conditions To exit the pre Alert state change the conditions or press the PTT e Solid the radio entered the Alert mode 3 2 1 Status Icons Table 3 6 Status Icons cont d Icon O Kie Lowe D Description Man Down Failure Indicates the Man Down device failed Call Out Indicates Call Out alert Call Out Alert Arrived Indicates a receipt of a new Call Out message Call Out Alert Unread Indicates unread alert in the CO Box End to End Encryption E2EE Solid when the E2EE is enabled e for the selected talkgroup e for the highlighted private number e for the manually entered private number e when transmitting voice in Group Calls e when transmitting voice in Simplex Private Calls Blinking when the End to End Encryption is enabled e when receiving voice in Group Calls e when receiving voice in Simplex Private Calls e during encrypted Duplex Private Calls SDS End to End Encrypti
96. ification requested by your service provider cannot be followed by the radio due to its settings the radio rejects 1t and displays Service Not Available message 2 14 2 10 6 Assistance Call 2 10 6 Assistance Call Assistance Call feature helps you to call for assistance during normal and non critical situations Starting an Assistance Call means starting a private call on a configured ISSI number Assistance Call destination address and priority can be configured in the codeplug This feature is only supported in TMO mode Assistance Call can be a simplex or duplex call depending upon your service provider settings An Assistance Call is full duplex when you start the call using radio menu When you type the number and press PTT then your radio starts a half duplex call but if you type the number and press SEND then the call is duplex 2 10 7 DMO Individual Call Presence Check If the other party is listening the Presence Check feature allows the user making a DMO private call to have a confirmation This is important in situations where it is crucial that the message gets through A radio with Presence Check enabled displays the Party not available message if the other party does not answer To use this feature both radios need to support it In addition radios can be configured to Accept DMO Individual Calls with Presence Check If enabled the radio accepts incoming calls with or without the presence check If disabled the rad
97. ignaling a blank line is displayed in its place 2 18 7 Talking Party Identification 2 48 The PDUs and facility elements for these TETRA Supplementary Services are not supported However identification presentation functionality is supported in most cases using the information found in the call setup messages 2 18 8 DTMF Overdial 2 18 8 DTMF Overdial This supplementary service allows the radio to send DTMF tones to both internal and the external network during the call conversation It is only possible to send DTMFs when in full duplex call This can be disabled in the codeplug enabled by default 2 18 9 Universal Time Display The radio can present time information to the user The time is derived from an internal clock The radio maintains the clock both when the radio is powered on and powered off y NOTE If the power is lost for example due to the flat battery the internal clock is not maintained In order to ensure the time displayed is accurate the time is displayed only if within the last 48 hours either of the following events have occurred The radio has received a network time update from the system e You have manually updated the time Also as the internal clock is not maintained after a power loss event the time is not displayed until either these events occur The feature is enabled or disabled and the default configuration can be set for the radio using the CPS or MMI The radio display supports th
98. in 107 typical Value 159dBm guaranteed 160dBm typical 5m 50 probable at 130dBm 10m 95 probable at 130dBm This specification may be subject to change without further notice All product features are subject to infrastructure support Selected features are subject to optional software upgrade 1 2 Radio and Features Ordering Options TETRA terminals are only available to Accredited Channel Partners who are advised of the discount structure applied to these products 1 3 Dongle Enablement Software Enablement Kits For information about available Software Features and their ordering visit Order Management Electronic Catalog OM eCAT Volume Descriptions and choose your region Navigate to Tetra Subscribers Software Features in your respective page E g for Western Europe go to http om ecat am mot com Volumes ECEUR index htm and navigate to Tetra Subscribers Software Features Software options can be ordered and enabled in three ways e You can have them enabled at Distribution Centre DC e If you have iTM you can enable them with license You can order by dongle 1 3 Dongle Enablement Software Enablement Kits Each software enablement kit ordered provides one dongle for the customer with a specific number of counters set according to the amount of software options ordered This kit number is applicable to both new orders or existing fielded terminals which require software enablemen
99. internally In addition the radio accepts SwMI modification of the call setup to direct enabling the infrastructure to generate the progress tones Phone calls can also be made between TETRA radios using the MS ISDN number as the called party number MS ISDN calls share the same gateway as phone calls that is PSTN gateway configured in the codeplug Ifan MS ISDN call is placed two radios can have a simplex or duplex call based on assigned ISDN number y NOTE The Dimetra Infrastructure does not support private calls and SDS through MS ISDN 2 11 2 Receiving a Phone Call Incoming phone calls land gateway to mobile use on off hook signaling The radio extracts the gateway ID from the call setup signaling to determine whether to start phone or PABX call That means you need to answer the call e g by pressing the SEND button 2 11 3 Call Restoration in Phone Call If the radio roams while being in an active phone call and the announced cell reselection is possible then the announced cell reselection is employed Also the call restoration procedures are performed 2 12 Emergency Operations 2 16 Emergency Operations are used in critical situations Pressing the EMERGENCY button or entering Emergency number and pressing SEND key activates one or more services depends on the service provider setting Sending Emergency Alarm Sending SDS Status Starting Silent Emergency Starting Hot Microphone operation Starting Emergency I
100. io Product Information Manual 3 2 1 Status Icons 3 10 Status icons appear when your radio is engaged in certain activities or when you have activated certain features Depending on your service provider settings status icons can appear in normal or large size By default they are large on the home screen and normal when browsing though the radio menu Table 3 6 Status Icons Icon Description Trunked Mode Operation L l In Service No Service Signal Strength The more bars the stronger the signal RF Power Indicates the High RF Power is enabled Shows the signal strength More bars indicate a stronger signal Migration Displayed when your radio is registered to the foreign network Broadcast Call Displayed when the radio is in the Broadcast Call Scan Indicates talkgroup scanning is activated in the radio Priority Scan Indicates that priority scanning is activated in the radio Data Connected Displayed when the Packet Data feature is activated and the external device sets up data connection with the radio Data Transmit Receive Displayed when the Packet Data feature is activated and the external device sets up data connection with the radio No number standby data session Number 1 2 3 or 4 indicates active data session with 25 50 75 or 100 bandwidth Direct Mode Operation ull gt Direct Mode Call Displayed during a Direct Mode call more bars
101. io can send the delivery report by using an appropriate TETRA signaling even if the originator requested a short report The radio can support the old SDS TL standard for operation on legacy systems or for operation on other SwMIs An externally connected device may access the SDS services in the radio using AT commands and TNP1 protocol An external application may use this service to send and receive SDS statuses SDS user defined data types 1 2 3 and 4 Downlink SDS messages type 4 are presumed to contain a PI for identifying the target application If an external application has registered with the radio for that PI the radio delivers the message to the target application The radio may receive downlink SDS messages that are successive retransmissions of a message already received and acknowledged by the radio The radio does not display these messages nor store in them in the inbox nor send them to an external application 2 13 1 Status Messages You can select from a list of up to 100 pre programmed alphanumeric aliases each of which corresponds to a status value The valid range of uplink status values is a set of provisioned parameters If the radio is not enabled with targeted status the status value is sent over the air interface to the address of the selected group The radio recognizes the general status acknowledgment sent from the SwML as well as the negative acknowledgment In TMO if no status acknowledgment or negative acknow
102. io is busy Phone Ring Back Played on the initiating phone when the Phone Call is being setup Private Ring Back Played on the initiating phone when the Private Call is being setup Ringtone 1 Ringtone 2 Ringtone 3 Ringtone 4 Ringtone 5 Simplex Volume Set Played when adjusting simplex volume Appendix B Glossary ADD Audio Device Descriptors AIE Air Interface Encryption Air Interface Encryption AIE Provides confidentiality on the radio link over the air SEE ALSO Encryption Announced Cell Reselection Cell reselection where radio Mobile Link Entity MLE informs the Switching and Management Infrastructure SwMI both in the serving cell and in the new cell that cell change is performed APAC Asia Pacific region ASSI Alias Short Subscriber Identity SEE ALSO Short Subscriber Identity Audio Device Descriptors ADD A structure which provides hardware information about a particular audio accessory for both IMPRESS and core accessories Files with ADD have an extension add Base Station Term used to identify the installation including the BTS antenna and ancillary equipment BTS Base Transceiver Station Calibration values A set of important and unique factory defined values such as frequency tuning assigned to radios Also known as Sensitive data CCK Common Cipher Key TETRA Radio Product Information Manual Central Network Equipment The equipment located at the Mas
103. io only accepts private calls without the presence check 2 10 8 DMO Individual Only Talkgroups It is possible to configure some or all DMO talkgroups to allow only individual calls This helps optimize frequency allocation in Direct Mode Operation 2 11 Phone Call The phone call service enables a radio in TMO to communicate in a one on one simplex or duplex conversation with a phone for example a phone calls enabled TETRA radio or landline number using a telephone switch The radio supports individual call service to an external identity Two phone call types are available PSTN a full phone number is addressed to the defined PSTN gateway address PABX phone number for internal calls numbers dialed are addressed to the defined PABX gateway address Y muaa The PSTN phone call is supported when PSTN PABX feature is enabled in the codeplug and the SwMI supports this functionality The PSTN PABX gateway must be configured properly No more than one PSTN PABX gateway ID and one PABX PABX gateway ID are available in the radio TETRA Radio Product Information Manual 2 11 1 Initiating a Phone Call The radio is able to initiate phone calls to a PSTN PABX with duplex speech capability This call type uses TETRA individual call signaling using single stage dialing and hook setup for outgoing calls Using the hook signaling for phone calls implies that until a traffic channel is allocated the radio generates all feedback tones
104. ional status is indicated on the radio display Also if configured by service provider the radio gives an audio visual notification upon reception of LIP command Depending on the radio configuration viewing the radio position and the status of the visible satellites is available The position may consist of longitude and latitude UK or Irish grid coordinates The GPS Location Service feature can be enabled or disabled as a whole using the CPS It is possible to configure the feature parameters using the CPS or over the air The CPS configuration provides a default profile The commands received over the air may overwrite the default profile configuration The profile assigned to the radio determines when to send location data what data to send with what accuracy and to what address All data requests and configuration commands received over the air are checked to confirm they have come from a trusted source Location reports are accepted only from authorized ISSIs or IPs depending on the configured transport layer SDS Packet Data y NOTE Ensure the application receiving location messages and the radio are configured in a corresponding way Otherwise the radio will reject all system GPS requests The radio supports GPS triggers functionalities using LIP or LRRP to report GPS positions when the radio meets a set of criteria The following triggers together with their specific parameters can be set up by service provider Table 2 6 GPS
105. ir capacity depends on the combination of stored short and long messages in each of these folders If Inbox is empty Outbox may store up to 100 short messages or at least 20 full size long messages If Outbox is empty Inbox may store up to 100 short messages or at least 10 full size long messages When you enter Messages submenu the number on the right side of Inbox and Outbox is indicating the number of the messages stored If the Outbox is empty then the radio displaysNo Messages notification Upon receiving a text message the radio places the text into a circular buffer You are notified when a new text message is received and a quick access to read the message is provided If a delivery report is requested the radio sends it upon receipt of the message by SDSTL If a consumed report is requested the radio sends it when you read the message Y muaa If you read the message when the radio is out of service the report may not be sent You can save incoming or edited outgoing text messages These messages can be edited and sent 2 13 2 1 SDS Messages Concatenation For each message you can verify its timestamp The timestamp displayed is extracted from the SDS TL PDU The timestamp is generated and inserted to the message by the SwMI 2 13 2 1 SDS Messages Concatenation This feature allows sending long text messages up to 1000 characters All the messages that are longer than 140 characters are divided and sent separately one after an
106. is possible because the radio asks its serving cell to perform the reselection and the SwMI performs all of the roaming signaling The radio then moves straight to the traffic channel on the new cell and continues the call without call restoration 2 17 7 Air Interface Migration The Air Interface Migration AIM feature enables the radio to migrate to a foreign SwMI that is the radio registration in a foreign SwMI is allowed The AIM also enables the radio to attach the groups in a foreign SwMI and to make and receive calls and SDS The AIM services cover individual call group call and individually addressed SDS or Status In order to receive group calls or group addressed SDS and Status from a group of the current network the radio has to attach the nominated group The radio cannot migrate to a foreign network while it is in an active call The radio also cannot attach a foreign group on the current network hence no group addressed status SDS messages can be sent to home network of the migrated radio After migrating the radio is in the Clear Mode When AIM feature is enabled the radio selects the network in the Foreign Net mode selectable in the radio MMI Foreign Network Foreign In this mode radio selects the network automatically where the home network Net is not available The radio registers to any network that it finds that is already programmed into its codeplug list of networks i e no user manual selection is required Network s
107. is the same as for Accept e Reject display returns to the home display and the talkgroup is set to the one before the call out Call out alert can be addressed as follows e ISSI an individual e GSSI a group of recipients All incoming and outgoing call out messages are stored in CO Box Call Out Box and can be managed through the MMI There is a two level structure for the alerts First level is the main alert list and the second one are all the messages associated with the alerts Both lists are displayed chronologically with the newest on top The capacity of the CO Box is ten call out alerts and 100 messages incoming outgoing It has also the overwrite policy which deletes the oldest one upon receipt of a new call out message When a new call out arrives the new call out overrides the old call out even if it has not been responded An ongoing call out overrides the old one in any phase of the call out alert In normal mode you can browse the CO Box and read all the call out messages In the call out mode you can only read the ongoing call out messages The call out service function in two main phases 1 Alert Phase you receive the alert with the associated messages that you can respond to These messages provide all the important information about an incident A special tone is played when the alert is coming in The tone volume range is configured in the codeplug and cannot be adjusted through the MMI The conditio
108. ision talkgroups into the radio over the Air Interface SEE ALSO Talkgroup Encryption Secure communications systems are designed to provide coded encrypted signals between some or all links in the system In order to do this each device involved in secure communications is loaded with a multi digit encryption variable called a key This key is used by an encryption algorithm built into the device to encrypt voice or data as needed Only devices in the system with the same algorithm and encryption key can decode the encrypted signals Encryption The manipulation of a packet s data in order to prevent anyone but the intended recipient from reading that data There are many types of data encryption and they are the basis of network security ESI Encrypted Short Identity ESSC EMEA System Support Center ETSI European Telecommunications Standards Institute European Telecommunications Standards Institute ETSD The European standards organization responsible for the TETRA standard Firmware Computer instructions that reside as read only software on a radio s flash memory Fixed Network Equipment Switching and Management Infrastructure Flash A storage chip integrated in to radio hardware that can be erased and reprogrammed TETRA Radio Product Information Manual Flashing Writing a software image file to a radio GCK Group Cipher Key GCK KAR Group Cipher Key Key Association Range GPIO General Programmable Input Ou
109. iteria Congestion level Security Class Subscriber Class Home Location Area Home Location area LA Boundary St Sh Jet Ree d 7 2 17 6 Seamless Handover 9 Cell Load The radio prefers a cell that has a higher service level to one with a lower service level If the radio is operating on a serving cell that has a lower service level than a neighbor cell the radio roams to the neighbor even during a call During network reconfiguration a significant number of radios registered on one cell may roam This roaming can cause major congestion on specific cells In order to avoid the congestion on control channels for the specific cells the specified radios roaming should be distributed in time As the operation cannot be performed immediately for all the radios some of the radios must wait longer to roam The time cannot be programmed not to cause any of the radios to have inferior roaming capabilities Thus the roaming time for the radios is randomized The randomization means that after roaming scenario starts a radio is not sending registration parameters to other cells at once but waits random time before sending registration PDUs to other cells Link failures and other related scenarios are not randomized not to cause any unwanted delays in restoring the link 2 17 6 Seamless Handover Seamless handover eliminates voice interruption during calls by enabling the radio to roam faster between cells while transmitting Faster roaming
110. ity RCU Remote Control Unit Remote Control Unit RCU A small device attached to a covert radio over a thin wire used for operating the radio Remote flashing Programming the transceiver via the control head RSM Remote Speaker Microphone RSSI Radio Signal Strength Indicator RUA Radio User Assignment RUA RUI Radio User Assignment Radio User Identity RUI Radio User Identity SCK Static Cipher Key SDMO KAG Secure Direct Mode Operation Key Association Group SDS Short Data Service Selling Feature Requires a USB dongle with purchased licenses Appendix B Glossary B 9 TETRA Radio Product Information Manual Semi Duplex Private Call Also called Private Call or Express Connect Call In this type of one way call the user presses and holds the PTT while talking and releases the PTT while listening SEE ALSO Private Call Push to Talk Sensitive Data A set of important and unique factory defined values such as frequency tuning assigned to radios Short Data Service SDS A flexible bearer service that transfers information from one interface to another Short Subscriber Identity SSD The network specific portion of a TETRA Subscriber Identity An SSI is only unique within one TETRA subdomain one TETRA network SIM Subscriber Identity Module Software Image A collection of files distinguished by individual releases It contains firmware codeplug and audio template files dedicated to speci
111. ledgment is received the radio retries sending the message The number of retries and time to wait before retrying are provisioned parameters You are notified of the delivery status As there is no acknowledgment for DMO status messages you are notified only of sending the status message The radio does not initiate sending of status messages on a traffic channel If the radio is provisioned with the targeted status the status value is sent over the air interface by default to the last sent target You have also an option to specify a different individual or group to send the message to In other words you can send an SDS status message to a directly entered ID for example ISSI GSSL MS ISDN If the radio is not provisioned with the targeted status and you want to send an SDS status message the following possible actions apply e When the default address type of targeted SDS status is set to Private or Phone the default address is used as ISSI or ISDN depending on configuration e When the default address type of targeted SDS status is set to group the selected talkgroup address is used e When the targeted SDS status is set to Dynamic the status message is sent to the address configured for the Dynamic statuses or defined by a dispatcher by means of SDS Remote Control The radio accepts status messages from addresses it is monitoring The radio can be preprogrammed with an appropriate text associated with each status value The
112. mage and a text string which can also be provisioned When the screen saver is being displayed any key input or incoming service causes the screen saver to deactivate 3 2 5 Languages Supported Table 3 7 Languages Supported Language English Yes Arabic Yes Chinese simplified Yes Chinese traditional Yes Croatian Yes Danish Yes Dutch Yes French Yes German Yes Greek Yes Hebrew Yes Hungarian Yes Italian Yes Korean Yes Lithuanian Yes Macedonian Yes Mongolian Yes Norwegian Yes Portuguese Yes Polish Yes Russian Yes Spanish Yes Swedish Yes User defined Yes z 3 17 TETRA Radio Product Information Manual 3 3 Audio 3 3 1 Tones Motorola TETRA terminal supports audible user notification tones Tones for events are divided into five categories e Keypad for events triggered by key press e Alert for events triggered by an application e Ring for events triggered by incoming outgoing call e Callout for events triggered by Call Out alert e Voice for the event triggered by voice volume set A category may have many or few associated events The number of tones is limited a specific tone may be used for indicating several different events The generated tone may be mixed with the received speech signal replace it or be played while the radio is in idle i e no received or transmitted speech dependent on its category and the features interaction The right tone event loudness is an objective matter Motorol
113. n can be selected e Network e Range e Talkgroup name e Time and date Home mode display e RMS FMS e ISSI 3 2 4 Display Features The radio utilizes colors to highlight certain special situations e When the radio is in an emergency mode call e When in the call out mode alert received state standby state accept the state In the RUA RUI when you are logged on or pseudo logged on If the display flip is provisioned the radio provides the ability to reverse the direction of the display Hence the display can be read when holding the radio upside down The radio has four font size levels that you can choose using the menu The backlight can be provisioned to operate in one of the following modes e Disabled The backlight does not operate at all e Semi Auto Pressing a provisioned one touch button toggles the on off state of the backlight The backlight is also turned off automatically when the backlight timer runs out 3 16 3 2 5 Languages Supported e Auto Pressing any key automatically turns on the backlight The backlight remains on until the backlight timer runs out or ifa provisioned one touch button is pressed to turn 1t off You can also toggle between the modes using the menu The radio supports an option to display a screen saver when the radio has been idle for a set time or when you explicitly activate it The screen saver consists of an image which can be provisioned from any GIF i
114. n create an audio profile using the 3 User Profiles Using the CPS you can enable disable an audio profile in the codeplug Using the CPS you can give an alias name to a particular profile configured in the codeplug The audio profiles are created and maintained independent of each other Creating or modifying one audio profile does not have any impact on the others The radio enables toggling audio profiles using the menu or using the One Touch Button You can change the audio profile during an active call 3 3 6 2 Transmit Automatic Gain Control The Transmit Automatic Gain Control TX AGC provides flexibility in terms of operating environment The TX AGC allows to transmit from a radio both indoor and outdoor without having to change a profile The TX AGC provides normalized sound levels to the receiving party 3 3 6 3 Howling Suppression The howling suppression is a mode increasing the stability of the acoustic feedback loop To enable this anti howling function use the menu or the corresponding One Touch Button The radio eliminates howling caused by the feedback loop from the receiving radios to the sending radio in simplex calls When the howling suppression is enabled Microphone and Speaker gain reduction values corresponding to the active audio profile are taken into use You can toggle the howling suppression during an active call 3 4 Testing 3 4 1 Test Page 7 NOTE The Test Page option must be enabled in the codeplug
115. n if your location information can be calculated in such situations it may take longer to do so Therefore in any emergency situation always report your location to your dispatcher Where adequate signals from multiple satellites are available your GPS Location Service feature provides a location most probably near to your actual location For GPS feature performance under ideal test conditions see Table GPS Specification The radio can be triggered to send Location Reports in various circumstances for example e Upon a request e Entering Emergency Mode e At specified time intervals e At specified distance intervals The Location Reports can be sent in two ways using e SDS e Packet Data If the Location Reports are sent over the Packet Data a Packet Data icon is displayed when the message is being sent 2 56 z 2 25 GPS Location Service If the Location Reports are sent via SDS with User Defined Data Type 4 as a transport layer either the ETSI Location Information Protocol LIP or Motorola Location Request Response Protocol LRRP GPS Location Protocol is used The LRRP GPS protocol either use SDS TL for added reliability or Simple GPS with no SDS TL for saving air interface resources GPS Protocol Identifiers are LRRP SDS TL 131 LRRP Simple GPS 3 LIP GPS 10 Location reports are sent in TMO and can also be provisioned to be sent in DMO If the radio is provisioned to provide user indications the feature operat
116. n perform scheduled transmissions of the future TM SCK addressed to each CMG The radio requesting a TM SCK triggers the site to schedule additional transmissions of the requested TM SCKs These transmissions are addressed to either the CMG GTSI that the radio belongs to or its ITSI The SwMI can perform scheduled background transmissions of the future GCKs addressed to each CMG The radio requesting for a given GCK triggers the site to schedule additional transmissions of the current and the future versions associated of the requested GCK These transmissions are addressed to either the CMG GTSI that the radio belongs to or its ITSI The SwMI can perform scheduled background transmissions of the current and the future DM SCK addressed to each CMG The radio requesting for a DM SCK triggers the site to schedule additional transmissions of the requested DM SCK These transmissions are addressed to either the CMG GTSI that the radio belongs to or its ITSI 2 14 4 6 Encryption Mobility A Class 2 or Class 3 radio can operate on a lower class SwMI depending on configuration A radio that is provisioned not to allow operation on a lower class SwMI does not register on such a cell A Class 2 or Class 3 radio moves to a cell that supports an SCK CCK GCK that the radio possesses applies AIE to the registration PDU If no acknowledgment is received the radio sends the registration in clear 2 14 4 7 Encryption MMI A Class 2 or Class 3 radio that is i
117. nables you to read write and modify contact list entries using AT commands 2 8 Call History A call history stack is provided which consists of the following e Last dialed numbers e Missed call numbers e Answered Received call numbers Additionally for the recent calls the time when a call was established and the call duration is available The Call History stack holds private TETRA IDs as well as phone and PABX numbers Numbers from the stack may be viewed selected and called However outgoing duplex calls from Recent Calls list display in DMO are not allowed When you scroll through the lists the entries appear in the opposite order the most recent shown first When a call is made to a number that exists in the last dialed list this number is not duplicated in the list and is moved to the beginning of the list However a missed call and received entries are duplicated in the corresponding call list The call history lists are available after next power up You can save a number from the call history stack to the address book 2 9 Group Call 2 9 1 2 6 The group call service enables the radio to communicate with a group of other TETRA radios using point to multi point operation This service is available in both TMO and DMO You can initiate a new group call to the selected talkgroup or talk back to the existing group call by pressing the PTT button Programmable Talkgroups The radio offers a talkgroup list facili
118. ndividual Call Private or MS ISDN Sending the GPS location information 7 NOTE It is possible to power up the radio by pressing the Emergency Button Depending on the service provider settings the radio can start Emergency Operations automatically If the radio was PIN protected except SIM PIN Emergency Operations will bypass the PIN lock for the duration of the Emergency Operations 2 12 1 Emergency Group Call During Emergency Operations the radio automatically rejects phone PABX and private calls and does not monitor the talkgroups in the selected scan list However if an ATG is the selected group the radio monitors the sub groups associated with the ATG When entering Emergency Operation any ongoing voice call is aborted or cleared down Any packet data transfer in progress is aborted However the session is kept open 2 12 1 Emergency Group Call The Emergency Group Call has the highest communication priority that means it is the pre emptive call Emergency Group Call is available in both TMO and DMO modes During Emergency Operations Emergency Group Call can be started by pressing PTT The MS may also support Hot Microphone operation which allows the Emergency Call to be conducted without pressing PTT If a radio receives an incoming group call with emergency priority the display shows that an emergency call has been received and a special audio alert is played An emergency group call can be configured as non tactical o
119. ng Hot Microphone resume Y NOTE When the user is in the Emergency Mode pressing EMERGENCY button restarts the Alternating Hot Microphone 2 12 8 Silent Emergency Mode The Silent Emergency Mode is a type of emergency services that provides no audible indications and no keypad tones at the entrance All the display indications are as in the idle mode However the radio cannot use any services except for Receiving Ambience Listening Sending Silent Emergency Alarms Sending GPS location reports VW NOTE If you try to activate any other feature it is blocked If the Silent Emergency feature is enabled the radio enters Silent Emergency Mode on pressing the EMERGENCY button After entering this Mode the radio stays in TMO or switches to it depending on the actual state Once in TMO the radio sends Silent Emergency Alarm y NOTE If the radio is in a private or group call the radio waits until the call ends and then enters the Silent Emergency Mode The radio keeps re sending the alarm until successful sending is confirmed After the alarm is successfully delivered the radio stays in Silent Emergency Mode and waits for the Ambience Listening Your radio exits the Silent Emergency Mode under the following conditions Press MENU and then key within 3 seconds Press MENU simultaneously with right NAVIGATION key Press both SOFT keys simultaneously No success in sending the Silent Emergency Alarm and the maximum number o
120. ngs you can override the address association and select using the MMI menu whether an SDS is sent to clear or encrypted contact Group or Private Number The radios support the high security mode configurable using the CPS In this mode the association that binds the address to a given cryptogroup is always mandatory If no cryptogroup associations exist this means that the keys are not loaded In such situation the radio discards any outgoing or incoming message that is encrypted You are alerted when this situation occurs This feature can only be disabled using the KVL 2 13 8 Store and Forward 2 13 8 Store and Forward This feature allows communicating with each other without being available at the same time If the destination is not reachable the message is stored in the system if supported until it is available or the expiration time is exceeded The system is configured to delete the message after a preconfigured time and this time cannot be configured using the radio You can send the store and forward messages to an individual address or a group Depending on the codeplug settings if you choose to send it to the group the message status is switched from Store and Forward to Immediate 2 13 9 SDS Receive Failure Notification When a radio fails to decrypt a received SDS message it displays a notification including the ISSI of sender and reason for failure 2 14 Security Services The radio provides TETRA security feat
121. nly includes voice communication You can only clear the fallback mode manually The dispatcher can test the feature by using the call out test The radio displays then Call Out Test and generates the alert tone A soft key is available in the MMI with the label Test OK After responding to it the display returns to the previous mode Storm plan alert is a special case of call out This alert is sent out to the larger group of people You can respond to it with any key stroke After responding you proceed to the information phase The storm plan alert is sent several times to raise reliability 2 24 Radio Messaging System The Radio Messaging System RMS feature enables radios to receive and send RMS messages through the TETRA network using the Short Data Service SDS Transport Layer TL Figure 2 7 Radio Messaging System Flow Model Control Room RMS PI SDS TL MS PI SDS TL gt lt RMS PI SDS TL y Radio lt RMS Status gt RMS Free Text gt A Short Data Router SDR provides TETRA short data services between host applications connected to Dimetra Mobile Stations or between a host application connected to a Dimetra Mobile Station and a host application connected through the Dimetra Master Site Furthermore the SDR provides TETRA short data services directly between two Dimetra Mobile Stations or directly between a Dimetra Mobile Station and a host application connected through the Dimetra Master Site To re
122. nnectivity allowing the following datagram exchanges e Radio External Equipment TE for example PC External Equipment TE Network through radio The radio supports IP version 4 packet TNPI services can use one of two PPP methods to connect from the terminal equipment to the radio local mode and wide mode The TNP1 should be used in wide mode wherever possible to allow the parallel operation of TNP1 SDS services and packet data services over a common PPP link If the transmit inhibit is entered the radio drops the wide mode connection thus the PEI goes back to AT mode Then the TNP1 client detects this change and reinitiates the PPP session in local mode The radio disables the TNP1 session while being in the DMO AT commands are used to initiate the PPP service for TNP1 to operate Once the PPP session is running all AT commands are blocked When the PPP session is closed AT commands are available 2 16 1 TNP1 IP Addressing Table 2 5 TNP1 IP Addressing Addressing Mode Description Wide Mode All TNP1 services are available including packet data transfer towards the SwMI The address used is the dynamic address MS IP or configured statically Local Mode All TNP1 services are available except packet data transfer The addresses used are the two static addresses TE IP 10 0 0 101 and MT IP 10 0 0 100 Port Addressing The radio uses a fixed port address for reception and transmission of TNP1 packets The po
123. ns for stopping this tone are configured in the codeplug for example upon pressing any key Additionally an ongoing alert tone is paused on incoming call out group call This alert is resumed once the call ends if not stopped before 2 Information Phase you are in the call out mode and you may receive more messages about the incident with the text or voice You can also query for more information using the voice group call or the call out text function which enables to send a text message to the dispatcher host application The voice message can be sent with the high priority as a group call You can answer back to the group or to the dispatcher using the voice group call You may receive more info about the incident via either via subsequent text or voice messages This is a selling feature 1 Call Out Interactions When you receive a call out alert while being in the emergency mode the message is ignored In the transmit inhibit mode you can receive call out messages However you cannot respond until the transmit inhibit mode is deactivated When you decide to leave the transmit inhibit mode after viewing the message the radio prompts to accept standby or reject the call out The call out feature is not supported in DMO 2 24 Radio Messaging System In the fallback mode that is when you are in the local site trunking you can receive a call out call In such case the receiving radio enters the call out fallback mode which o
124. nvolved in a clear call provides a visual and an audible indication informing that the call is not encrypted if enabled by the service provider 2 14 4 8 AIE Key Storage The radio stores all the keys SCK CCK DCK GCK in a sealed manner in non volatile memory of the radio However they are not stored in the codeplug The radio supports loading of the SCK keys manually using the Key Variable Loader KVL By using a special key combination you can delete the cipher keys in the radio Depending on configuration you may erase either all keys or only the short term keys 2 14 4 9 Deleting User Keys Prerequisites The user key deletion is enabled in the codeplug 2 31 TETRA Radio Product Information Manual Procedure Steps 1 Verify that the radio is turned on 2 Press the following key sequence 0 0 The key deletion takes up to 30 seconds During the period the battery must not be removed Removing the battery during that period may lead to radio malfunction Result Encryption and or Authentication keys are deleted The radio enters Temporary Disable state and must be manually restored by the service provider 2 14 5 Secure DMO The Secure DMO feature guarantees key ciphered transmission in the DMO When DM SCKs are provided by OTAR you are informed in case the radio does not contain the complete set of SDMO keys Whenever the radio enters DMO and the radio does not possess past and present DM SCKs for all
125. o use the multiple group monitoring define a scan list the user activated scan list This list holds up to 20 talkgroups which you monitor in addition to the selected group You can choose only one user activated scan list at a time When this list is activated the radio begins to monitor traffic for these groups in addition to the traffic for the selected group The radio can allow creating and editing the scan list using MMI Up to 40 scan lists can be defined If the SwMI instructs a radio to detach one of the scanned groups the radio stops monitoring the group but the group remains in the scan list Subsequent attachment of a group by the SwMI causes the radio to begin monitoring the group again The SwMI may also instruct a radio to attach groups from out of the scan list If the group attachment is accepted the radio monitors the group The radio may passively monitor the following talkgroups if they have been attached or are always attached e Selected talkgroup e ATG associated with the selected talkgroup if this talkgroup is not set as Permanently detach e Talkgroups associated with the selected ATG if this talkgroup is not set as Permanently detach e Talkgroups in the user activated scan list if scanning is enabled and the SwMI initiated detachment has not been performed on these groups Talkgroups in the SwMI controlled scan list if scanning is enabled Talkgroups with the class of usage set to Always Scanned
126. ol Este Ciudad Jardin Pasa E Casa 65 Quito Mexico 52 555 257 6700 MOTOROLA DE MEXICO S A Calle Bosques de Alisos 125 Col Bosques de Las Lomas 05120 M xico D F xviii Service Information Americas Service Information Telephone Numbers and Addresses of Latin America Motorola Centers cont d Country Telephone Number Address Peru 511 211 0700 MOTOROLA DEL PERU S A Ave Rep blica de Panama 3535 Piso 11 San Isidro Lima 27 USA 954 723 8959 MOTOROLA SOLUTIONS INC Latin American Countries Region 789 International Parkway Sunrise FL 33325 Venezuela 58212 901 4600 MOTOROLA DE LOS ANDES C A Ave Francisco de Miranda Centro Lido Torre A Piso 15 El Rosal Caracas 1060 x1x Icon Conventions The following graphic icons which help identify situations or settings crucial to proper radio operation and user safety are used throughout this document The signal word DANGER with the associated safety icon indicates information that if disregarded will result in death or serious injury The signal word WARNING with the associated safety icon indicates information that if disregarded could result in death or serious injury or serious product damage The signal word CAUTION with the associated safety icon indicates information that if disregarded may result in minor or moderate injury or serious product damage The signal word CAUTION may be used without the safety icon to state potential damage or inju
127. om xiii TETRA Radio Product Information Manual Service Information Telephone Numbers and Addresses of the Asia and Pacific Motorola Centers cont d Indonesia 62 21 3043 5239 Thailand Tel 662 653 220 Fax 668 254 5922 India 91 9844218850 China 86 10 8473 5128 xiv PT Motorola Solutions Indonesia 30th Floor Gedung BRI Il Suite 3001 Jl Jend Sudirman Kav 44 46 Jakarta 10210 Indonesia Contact Eko Haryanto E mail Eko Haryanto motorolasolutions com Motorola Solutions Thailand Ltd 142 Two Pacific Place Suite 2201 3220 Sukhumvit Road Klongtoey Bangkok 10110 Contact Nitas Vatanasupapon E mail Nitas motorolasolutions com Motorola Solutions India Pvt Ltd C o Communication Test Design India Private Limited 4 5 Maruthi Industrial Estate Rajapalya Hoodi Village Bangalore 560048 India Contact K Umamaheswari E mail umamaheshwari motorolasolutions com Motorola Solutions China Co Ltd No 1 Wang Jing East Road Chao Yang District Beijing 100102 P R China Contact Sophy Wang E mail C18170 motorolasolutions com Service Information AME Service Information Telephone Numbers and Addresses of the Asia and Pacific Motorola Centers cont d Hong Kong 852 2966 4823 Philippines Tel 632 858 7500 Fax 632 841 0681 Korea 822 3497 3649 Taiwan 886 2 8729 8000 Australia 613 9847 7725 Motorola Solutions Asia Pacific Ltd
128. omers requiring a repair service should contact the Customer Information Desk and obtain a Return Material Authorization number Unless advised otherwise the equipment should then be shipped to the following address Motorola GmbH European Systems Component Center Am Borsigturm 130 13507 Berlin Germany E mail escc admin motorolasolutions com Telephone 49 30 66 86 1404 xl TETRA Radio Product Information Manual xii Mon Fri 08 00 am 06 00 pm CET Parts Identification and Ordering To get help in identification of non referenced spare parts contact Customer Care Organization of Motorola local area representation To request replacement parts kits and assemblies place orders directly on Motorola local distribution organization or through http emeaonline motorolasolutions com ElA Test Equipment Support For information related to support and service of Motorola Test Equipment contact Customer Care Organization of Motorola local area representation or see http emeaonline motorolasolutions com For customers in Germany contact the Equipment Service Group in Germany Telephone 49 0 6128 702179 Fax 49 0 6128 951046 Latest Versions of Manuals To download the latest versions of technical manuals go to http emeaonline motorolasolutions com Submit Your Comments If you have any comments or would like to report a problem regarding Motorola publications send an e mail to escc admin motorola
129. on Solid when the E2E status of an SDS message or the E2E status of a message recipient address In High Security mode when your radio processes only the encrypted information this icon is always visible in when you are in the messages menu for example Inbox Unread New WAP Message Indicates that you have not entered WAP Box since last WAP message was received Blinks when the priority is high WAP Message Icon Displayed next to the priority in the message list view WAP Message Time Displayed next to the create date in the message list view WAP Message Expiration Displayed next to the expiry date in the message list view 3 13 TETRA Radio Product Information Manual Table 3 6 Status Icons cont d Description WAP Message Title Icon Displayed next to the title along with the text in the message list view Keys Locked Indicates that keys are locked Non Secured Call Air Encryption Unavailable Blinking indicates that Air Encryption is not available when the radio e Is in the Local Site Trunking Mode e Attempts to connect to a gateway Not Secured Call Air Encryption Unavailable Alternately blinking indicates that Air Encryption is not available when the radio e Is in TMO Mode e Communicates through a gateway Not Secured Call Air Encryption Unavailable Blinking indicates that Air Encryption is not available in DMO Mode The icon appears after the PTT button is pr
130. on The two individuals can talk and listen at the same time without pressing PTT SEE ALSO Private Call Push to Talk B 7 TETRA Radio Product Information Manual Private Number Also called Private ID PSTN Public Switched Telephone Network PSTN Gateway A device that provides connectivity from a TETRA user to a PSTN subscriber and the other way around Additionally for the duration of the call the PSTN gateway allows TETRA signaling information to be passed from TETRA Switching and Management Infrastructure to the external network user and from the external network user to the TETRA SwMI in accordance with the TETRA Call Control CC procedures SEE ALSO Public Switched Telephone Network Switching and Management Infrastructure PTPC Point to Point Call SEE ALSO Private Call PTT Button Push to Talk button Public Switched Telephone Network PSTN Traditional telephone network Push to Talk Pressing this button on a radio allows the subscriber to transmit Radio A two way communication device used for voice and data Radio User Assignment Radio User Identity RUA RUD This feature allows to assign alphanumeric user names to radio users and to authenticate the radio users in a logon process Radio User Assignment RUA Part of RUA RUI feature SEE ALSO Radio User Assignment Radio User Identity Radio User Identity RUT Part of RUA RUI feature SEE ALSO Radio User Assignment Radio User Ident
131. oth cases if the radio is back in the coverage area and receives RUA request from SwMI it prompts you to log on If during the emergency operations you receive the force off it logs you off without exiting the emergency operations As long as the radio is in the emergency operations the radio display does not indicate any change When the radio turns on in the LST it prompts for the PIN If the correct PIN is entered the radio switches to the pseudo logged on state When you move to the LST the radio switches to pseudo logged on state However no prompt for the PIN occurs When you change to a different physical terminal the store and forward report is routed to the radio where you are currently logged on When the radio receives store and forward report it does not display the report as the reports have to match the sent SDS If an SDS consumer report is requested it is recommended that the receiver sends an explicit separate SDS message to confirm the message has been received and read The report is stored together with the sent SDS in the Outbox because of that when you log off delete the messages from the Outbox When you change to different physical radio the previous permanent radio does not receive the report The status of store and forward message in the Outbox cannot be updated 2 29 Camera The radio is equipped with a built in 5 MP camera Pictures resolution can be configured to 5 2 or 1 MP You can store pictures in the
132. other When a recipient receives all the parts of the message it displays as one on the screen When the radio receives an SDS message and the Inbox Outbox is full the radio acts according to the Buffer Full Overwrite Policy codeplug field settings When the text or status message is received and accepted the radio retrieves actual time information from its internal clock The radio can reconstruct a long text message consisting of up to ten short messages The maximum length of the message is 141 1000 what can be defined in the codeplug The radio recombines the text segments independently of the order they have been received to the correct order of the original message The message can be combined only if all their message reference number are correct and the segmented receiver timer is still valid You can send long text messages to an individual destination However sending long text messages to groups is not possible e Receiving the message during group broadcast call radio allows receipt of the text message during ongoing group call and broadcast call The group broadcast call is displayed with the New mail arrived icon and tone for mail reis played Emergency Mode you can receive SDS messages To read the SDS messages the radio have to leave the emergency mode Sending the SDS messages in the emergency mode is prohibited When sending long segmented text messages a timer is activated If not all segments of the message
133. our radio to replace the Home Display message to the predefined one 2 13 5 Predefined Templates ATS Entry Prompt This feature assists the radio in sending formatted messages with a predefined destination address MS ISDN SSI or TSI for computer applications You can select a predefined entry prompt which defines a message format to assist in the construction of an SDS message The prompt definition is set in the codeplug The definition sets areas that are read only areas that can be edited and the type of characters that can be entered numeric alpha numeric or phone digits Along with the message definition the address to send the message is provided When you send the message it is sent using SDS TL with the PI that is provisioned in the codeplug A receipt report is requested 2 13 6 SDS Air Interface Aspects The radio can be provisioned to send a short form SDS TL receive report when the originator of the message allows short form report The short form report uses specially designated SDS status values instead of SDS REPORT The radio supports SwMIs that employ store and forward service as indicated in the cell broadcast information The radio supports use of a service center which address is set in the radio The store and forward operation is supported However the radio notifies you only on successful sending of the message The radio does not wait for the report from the service center Downlink SDS messages types 1 2
134. performed except for cell reselection In transmit inhibit mode the radio joins group calls for any group that the radio is monitoring but the transmitting on that call is still prohibited The radio also displays any incoming SDS messages to the user The missed call feature is active in the transmit inhibit mode and allows checking what calls were missed However the radio attempts to prevent call setup retransmission from being recorded as separate calls If you initiate an emergency call the radio immediately leaves transmit inhibit mode and attempts to start the emergency call if the radio is in service If the radio is turned off in the transmit inhibit mode on turning on the radio asks whether to exit the transmit inhibit mode If you choose No the radio turns off 2 18 6 Calling Line Identification Presentation If the radio is provisioned with the calling line identification presentation CLIP the calling party number is transported as part of the incoming call setup signaling Also the calling party number is shown on the radio display If the calling party ID is programmed in the radio with a corresponding name the name is displayed in addition to the number Y muaa The number sent by the SwMI is expected to be in a form that can be used to call back the calling party at any other time Thus for instance the number can be stored in the address book If the calling party number is not present in the incoming call setup s
135. provisioned KAG and or it has not yet successfully received SCK Subset Grouping Type SCK Subset Number and SCK VN information from the SwMI then the radio e plays a special reject tone prompts a message indicating OTAR incomplete The radio provides SDMO status information to the user via the MMI DMOSCK Validity submenu inside the Security menu present only when configured in the codeplug DMO SCK is Valid DMO SCK OTAR is disabled and all DM SCKs are provided using the KVL e DMO SCK is Valid DMO SCK OTAR is enabled and the radio knows the current SCK information and has all the corresponding past and present DM SCKs e DMO SCK is Invalid in all other cases The radio supports system management of SDMO keys The radio using system managed SDMO requires the structure of DM SCKs used for SDMO the current active SCK Subset Number and Version Number information to coordinate key schedules The radio considers the last received variant of this information PDU as the most accurate indication of SDMO key configuration DMO SCK can only be used if Enhanced Security feature is purchased 2 14 6 End to End Encryption 2 32 The TETRA standard supports air encryption The radio creates the PDU Protocol Data Unit and the PDU is encrypted before transmission The base station receives this PDU and must decrypt it to know what to do with it and where to send it Thus if a PDU contains voice information the voice part of the messag
136. quest Point to Point Protocol PPP mode and then operates in PPP mode until the data connection is terminated The radios can operate both on the single slot packet data channel and the multi slot packet data channel The system provides point to point IP connectivity allowing the following datagram exchanges e Radio External Equipment Terminal Equipment for example PC External Equipment Terminal Equipment Network through radio The radio supports only IP version 4 packets The radio routes datagrams independently of the protocol sitting on top of IP The radio supports an MTU of 1500 bytes The radio provides the best effort delivery service However if the delivery fails the originating user application is informed by sending back to Terminal Equipment an ICMP message if possible TETRA Radio Product Information Manual The radio generates ICMP messages addressed to the Terminal Equipment in case of failed delivery due to the radio environment The delivery may fail due to for example no radio coverage e failed transmission e service interaction The packet data service PDCH access signaling has the same priority as circuit mode setup related signaling The radio uses advanced link for PD transmission and supports advanced link flow control The advanced link roaming if the advanced link is not disconnected between cells is supported where the SwMI supports it The radio does not support data compr
137. r tactical e A non tactical call is initiated on a talkgroup designated by the codeplug setting When in non tactical emergency mode you cannot switch talkgroups e A tactical call is initiated on the currently selected talkgroup In TMO if the radio enters emergency operations while the emergency broadcast call is active the radio continues on the call without initiating any calls and sends an emergency alarm 2 12 2 Non Tactical Emergency In Non Tactical Emergency the radio switches to a designated Emergency talkgroup when starting Emergency Operations This talkgroup is used for the complete duration of the Emergency Operations you cannot change the talkgroup In TMO it is possible to configure the radio to make Emergency Non Tactical Group Calls without sending attachment If this is set the radio assumes implicit attachment after receiving a temporary address In DMO the Non Tactical Emergency proceeds on the same frequency as the previously selected talkgroup The service provider can designate any ITSI address to be used for Emergency Operations this can be an Open Group broadcast address After exiting from Non Tactical Emergency the radio goes back to the previously selected talkgroup 2 12 3 Emergency Individual Calls Private or MS ISDN The Emergency Individual Calls are Simplex or Duplex Calls with emergency priority On pressing the EMERGENCY button the radio initiates an Individual Call to the provisioned ad
138. r the groups 2 9 11 Announcement Talkgroup The radio supports the concept of a group hierarchy A special group an announcement talkgroup ATG in addition to being a group logically contains up to 20 subgroups When you select an ATG as the selected group the radio monitors traffic received for the announcement group as well as the traffic received for any of the associated subgroups However the radio does not monitor the active scan list groups when an announcement group is selected When you select one of the subgroups of the ATG the traffic for the subgroup is monitored as well as the traffic for its announcement group not other subgroups though Each normal talkgroup may be associated with only one ATG An ATG cannot be associated with another ATG Depending on the codeplug settings you may be prohibited from initiating ATG calls In such case you are still permitted to initiate an emergency call to an ATG group 2 9 12 Broadcast Call Initiated by User This feature allows you to make a Broadcast Call from the radio initiated on the predefined talkgroup The alias message displayed during Broadcast Call as well as the call priority and destination address talkgroup can be configured in codeplug This feature can only be used in TMO mode During Broadcast Call other features are impacted No other services except emergency are allowed same as in emergency mode e Hot Mic functionality cannot be used e When Broadc
139. requencies Frequency List2 32 fixed frequencies Frequency List3 comprehensive hunt Frequency List4 comprehensive hunt e Data Sve Data Services allows access to the air tracer enable the conformance tests and the KVL mode Air Tracer Conf Test Conform test KVL Mode y NOTE To leave the KVL Mode power off and on E2E KVL Mode MS Logging e CE Monitor Crypto Engine Monitor Key Info Key Information allows displaying the security information for the following conditions For the serving cell Curr Cell SC Security class of the serving cell that is Security Class 1 Security Class 2 Security Class 3 Security Class 3 with GCK For the group OTAR CMG GSSI Crypto Management Group CMG group of MSs with common key material 3 21 TETRA Radio Product Information Manual For SDMO and TM SCK OTAR SCK SubsGrType SDMO SCK Subset Grouping Type Curr Subs Info current SDMO SCK Subset Number and SCK VN Fallback TMSCK current Fallback TMO SCK that is SCKN and SCK VN attributes SCK List list all SCKs stored in the MS that is SCKN and SCK VN attributes SCK version number 7 NOTE When checking that the SDMO key information in the radio be advised that the SDMO KAG SDMO Key Association Group range in the AuC Authentication Centre is from 0 to 9 and the range in the radio is from 1 to 10 For the GCK Group Cipher Key
140. rface color Blue for logged on and gray for logged off No additional icon indicates whether you are logged on Besides the logged on off states the radio can also be in the pseudo log on state indicated by the relevant icon The User ID is stored in the RUI List To verify who is logged on to the radio see the second line in the RUI list the first line is New User ID RUA RUI is a selling feature 2 28 1 RUA RUI Logging On You can log on yourself or the dispatcher can log you on The feature must be enabled in the codeplug by your service provider After turning on the radio the infrastructure verifies a request from the radio and checks if it supports the RUA RUI When the infrastructure accepts RUA request you are asked for RUI and RU PIN After providing correct information a successful logon occurs and full access is granted for specified time When a RUI and or RU PIN are incorrect a logon failure occurs The infrastructure sends the RUA reject signal to the radio If enabled in the codeplug limited service access is granted When the dispatcher is sending the RUA accept signal to the radio with the time period that the full service is granted then the successful book on occurs 2 28 2 RUA RUI Radio Behavior When the radio is logged off and receives RUA accept from the infrastructure without sending logon information it indicates book on with assigned logon period timer The radio sends automatically book on response ac
141. rophone time expires ends the Hot Microphone operation Then normal PTT operation in Emergency group call takes over that is the transmission is ongoing for the time the PTT button is held Subsequent EMERGENCY button presses during the Emergency Operation restarts the Hot Microphone transmission If a talk permit is granted to another member of the group the Emergency Call received tone is played If configured the radio automatically attempts to get talk permit again Pressing EndSOFT key or END key ends the Hot Microphone operation 2 12 7 Alternating Hot Microphone 2 18 The Alternating Hot Microphone is an enhancement of the Hot Microphone feature It allows you to have the Hot Microphone switched on and off alternately If this feature is enabled you can initiate the Alternating Hot Microphone by pressing the EMERGENCY button The Alternating Hot Microphone terminates when one of the following conditions is met The radio exits the Emergency Mode The Alternating Hot Microphone timer expires The PTT button is pressed The right SOFT key is pressed only during the transmission timeslot To skip your transmission timeslot and jump to a receiving timeslot press END key 2 12 8 Silent Emergency Mode Y muaa When the radio goes out of the service it enters the receiving mode and the Alternating Hot Microphone is on hold When the radio is back to the service the Hot Microphone transmission and the Alternati
142. rt number is 4024 2 17 Mobility Services Following is the description of the Mobility Services TETRA Radio Product Information Manual 2 17 1 Main Control Channel Frequencies The radio can find a wide range of main control channels The radio maintains stored lists of carrier frequencies which are scanned in order 1 A dynamic list of up to 32 discrete entries maintained only by the radio software 2 A static list of up to 32 discrete frequencies specified by the operator that can be preprovisioned The system operator can modify this list using the programming tool 3 A frequency range specification using a specific offset that can be preprogrammed in the factory The system operator can modify this range using the programming tool Then the radio scans all frequencies in 25 kHz intervals in the specified range 4 An additional frequency range specification Having two separate range specifications allows for two non contiguous blocks of frequencies or two different offsets 2 17 2 Control Channel Selection Each TDMA frame on a given carrier is comprised of four time slots of which any can be used as a physical channel The following types of physical channels are available Traffic physical TP channel used primarily for circuit call traffic e Control physical CP channel dedicated only for signaling e Packed Data Control PDCH channel dedicated for Packet Data traffic e Unallocated physical UP c
143. ry Optional Optional Optional N A Optional Mandatory N A Mandatory N A N A N A Mandatory N A N A N A A NOTE In the current release the radio does not support the following security features e Radio initiated authentication Support for TEA4 e Explicit authentication during DGNA Security Class 3G Not Allowed Mandatory Optional Mandatory N A Mandatory Mandatory Enhanced Security which consists of TMO Air Interface Encryption class 3G and DMO class 2 is a selling feature 2 28 2 14 4 1 Clear Radios Class 1 2 14 4 1 Clear Radios Class 1 A radio can be configured as a clear radio In such case the radio identifies itself in registration as a Security Class 1 radio and does not support encryption A Security Class 1 radio does not contain any encryption algorithms in 1ts software 2 14 4 2 Static Cipher Key Encryption Class 2 The radio supports static AIE using a set of up to 32 static cipher keys SCK shared by the SwMI and all authorized radios The radio then determines which static keys to use based on the SCK Number SCKN and SCK version number SCK VN broadcast by the SwMI A radio can be configured to support static key encryption In such case it identifies itself in registration as a Security Class 2 radio and attempts to negotiate Security Class 2 encryption Each radio then uses either the TEA1 or the TEA2 TEA 3 for Asia and Pacific Key Stream Generator KSG algorithm Each radio contain
144. ry that is not related to the product A IMPORTANT IMPORTANT statements contain information that is crucial to the discussion at hand but is not CAUTION or WARNING There is no warning level associated with the IMPORTANT statement W muaa NOTE contains information more important than the surrounding text such as exceptions or preconditions They also refer the reader elsewhere for additional information remind the reader how to complete an action when it is not part of the current procedure for instance or tell the reader where something is located on the screen There is no warning level associated with a note y SUGGESTION SUGGESTION indicates a recommendation from Motorola that does not require to be followed but might be helpful There is no warning level associated with SUGGESTION xxi 1 Product Overview 1 1 MTP6000 Series Overview The MTP6550 and MTP6750 are Motorola TETRA portable radios for mission critical communications Figure 1 1 MTP6550 TETRA Radio Product Information Manual Figure 1 2 MTP6750 The best in class receiver sensitivity in connection with 4W audio through the loudspeaker or IMPRES remote speaker microphone guarantees clear and reliable communication The radios meet and exceed MIL SPEC test standards as well as ETSI mechanical tests The MTP6000 radios are IP67 compliant which means they can operate even after being submerged in water On top of the best audio quality and rugge
145. s adi 2 54 2 24 Radio Messaging SM A A dais tadas 2 55 225 GPS Location Service ed ee EES 2 56 225 1 A ANI S oes Roa dad EES 2 58 2 25 2 GPS Military Grid Reference Syste rr e E a a ai 2 58 2 25 3 GPS Different Location Displays 000 ia ENN 2 59 2 26 Side CONME COL rta 2 60 QED TD WAP ER Eed 2 60 EEN EE 2 60 LID WAP A ooo 2 60 2 27 2 1 WAP Push Framework dt ioadi 2 61 2 27 22 WAP Pushy Service Indications esne a io 2 61 2 2 7 2 3 WAP Push Service Load ico a a aida eee 2 61 2 28 Radio User Assignment and Radio User Identity 2 0 c cece cece cece cence eeceeeeeeeece cece eeeee eeu eeeeeeeeesaessa eee ees 2 61 2281 RUARUTEO sing tee eaten e eet Begin A bs oes Shige Se Oe aA nd ES 2 62 2 28 2 RUA RUI Radio Bchavior nono i aia iaeaea iei i na a ea 2 62 228 3 RUA RUL Tinteractions cards a bil 2 62 EE 2 63 229 1 O A NS 2 63 E EIERE EE 2 64 CEET e 2 64 2 294 EXMEDA A EE TEN E E A NET E E ETE teres 2 64 A ES Light sorcier E ace ecco EE cede ac be Sua ATES G EAE AE Sa RAEE AAE EAE E EA ETT Ee 2 65 2 30 Radio Mass Storage sentene aa titi 2 65 iii TETRA Radio Product Information Manual 231 Blu EE 2 65 2 3151 Bluetooth Interaction A e AE SERN GRAV ARENT 2 66 2 312 Bluetooth Rest DEgs ena EE dE AEN 2 66 EE Interfaces A A A O EE Ee 3 1 3 1 Controls Indicators and Related Features 3 1 Lk LEDIndications e iii 3 1 3 12 Controls ad e EENG 3 3 FL SR Se EE 3 6 3 14 Automatic Key pad Lock ais 3 7 3 1 One
146. s each 6 wide The strips are numbered 1 60 beginning at the 180 174 W Zone 1 and increase to the East Each strip or Zone is then divided horizontally into 8 latitude bands 7 2 25 3 GPS Different Location Displays NOTE An example of an MGRS coordinate would be 19TDJ3858897366 which consists of 19 is the UTM Zone Number T is the corresponding UTM latitude band letter DJ is the MGRS Grid Reference used to define the 100 km square within the UTM UPS block The columns A Z excluding I and O like UTM start at 180 and increase towards the East Every three columns the pattern repeats Letters designating rows increase towards the North The letters cycle backwards through the alphabet in the southern hemisphere towards the South D is the MGRS column letter J is the MGRS row letter 38588 is the 5 digit MGRS Easting value It represents the number of meters East of the origin that is southwest corner of the 100 km square in which it is contained 97366 is the 5 digit MGRS Northing value It represents the number of meters North of the origin that is southwest corner of the 100 km square in which it is contained MGRS Support feature can be programmed in CPS The user can choose to display the GPS coordinates in MGRS format This is a selling feature 2 25 3 GPS Different Location Displays Table 2 7 Different Location Displays o de UK Coordinates Irish Coordinates UTM Coordinates er
147. s dt SE deeg 2 7 2 9 4 Talkgroup Blind Operation ooocococcnocncoinnconocononcnnncnnnnnnnonn nono nrrnnrrnnnr nr iar iar i e e 2 7 2 9 5 Recetve only TalkgroUpS mic a a a ai Dia 2 7 2 9 6 Non Selectable Talkeroups nono ncnnnrnnnnnnnrrnnnnnnrrnn rn nnrnrnnnnnnnnnineninonos 2 7 29 7 Talk Time TAMU sitiada 2 8 2 9 8 Receiving a Group Call catala cad 2 8 29 9 TalkeroUp Scanning senisesse tir a were a EA E ARE AEE ARAE SE 2 8 2 9 10 Priority Monitor sin od ia di a A EE aa 2 9 2 9 11 Announcement Talkeroun rro nrrnnrrnnrnnnnnnnnnnrnnninoniss 2 9 2 9 12 Broadcast Call Initiated by Uso naaa 2 9 29 13 Broadcast EE 2 10 29 14 Announcement Call cool 2 10 29 15 PTT Double Push iaa 2 10 2910 PT O 2 11 2 9 17 Talking Party Identifica cin ie din dad a eds 2 11 AMC o o ashes 2 11 2 9 19 Transmission During Group Call 2 11 2 9 20 AS AAA 2 11 2 9 21 Temporary Group Address 2 12 29 22 Late En ie 2 12 2 9 23 User Initiated Group Attachment 2 12 2 9 24 SwMI Initiated Group Amach Detach keset tii kesek sk ki ieee 2 12 2107 Private EE 2 13 2 10 1 Simplex Private Call EE 2 13 2 10 2 Duplex Private Call cuina id dr di di EEES rs Ea ETE EER toe 2 13 2103 Talk RE E 2 14 2 10 4 Call Restoration in Private Call iria 2 14 2 10 5 Call Modification rr nn r rn r rn r enn rr nan n nn rn esse essa eeeeseeeneeeeeeaeegas 2 14 210 6 Assistance Cl odias is 2 15 2 10 7 DMO Individual Call Presence Check 2 15 TETRA Radio Product Informa
148. s only one of those algorithms in its software When Security Class 2 Encryption has been negotiated encrypted PDUs are encrypted using SCK In DMO the system manager may choose the SCK and the key may be distributed from the TMO SwMI using the OTAR mechanism or provided manually using KVL 2 14 4 3 Derived Cipher Key and Common Cipher Keys Encryption Class 3 DCK CCK are required to prevent over exposure of key material Existing encryption systems use Static Cipher Keys SCK where one key is used for all radios and all calls Key material is often exposed and SCK logistics of changing keys consist in programming all radios and base stations DCK is used for individually addressed TM SDU Service Data Unit DCK CCK encryption provides Derived Cipher Key DCK for uplink from the radio to the BTS communication and Common Cipher Key CCK for downlink from the BTS to the radios group communication The DCK is derived from either the one way or mutual authentication process and the CCK is received during registry The radios supporting the dynamic key encryption identify themselves to the system as Class 3 radios during registry and attempt to negotiate Class 3 encryption A Class 3 radio supports group addressed signaling and group call traffic encryption using CCKs as well as encryption of uplink and down link individually addressed signaling messages and individual call traffic private or phone using its DCKs The radios support Over
149. s to start a service while the AL call is in progress the radio disconnects the call and initiates the requested service The radio allows performing actions that can be performed without releasing the AL call These actions include access of most menu items activating deactivating scan lists and changing talkgroups When changing talkgroups the radio appears as if it is performing an attachment The attachment appears to be successful but the actual attachment signaling is performed only after the AL call terminates When performing the attachment after the call no indication is shown to the user unless the attachment fails If you attempt to power down the radio in the active Ambience Listening call the radio enters Pseudo Power Off state 2 18 2 Pseudo Power Off 2 46 If you attempt to power down the radio in the active Ambience Listening call the radio appears to turn off However it remains fully operational from Layer 3 and below The radio has a blank screen and all LEDs are turned off 2 18 3 Auto Power On When the AL call ends in this pseudo power off state the radio automatically turns off If you attempt to power up the radio from the pseudo power off state the radio acts as if it is really powering up 2 18 3 Auto Power On The radio can be configured to turn on automatically after inserting the battery This functionality is configurable using CPS If the emergency mode was active before removing the battery the r
150. se result protocol between two parties based on their common knowledge of a secret key K to verify each others identity TETRA Radio Product Information Manual The SwMI authentication centre AuC provides a single K for authentication which is shared only with the radio Authentication is always initiated by the SwMI the radio can also authenticate the SwMI if set by the service provider 2 14 4 Air Interface Encryption The radio supports TETRA Air Interface Encryption AIE using the standard TETRA public encryption algorithms as defined in TETRA Security ETS 300 392 7 TEA TEA2 and TEA3 The focus of cryptography in TETRA is the encryption key TETRA AIE provides 12 000 000 000 000 000 000 000 000 key combinations TETRA TMO has three classes of encryption e Class 1 clear none e Class 2 static key encryption SCK e Class 3 derived key encryption DCK sometimes called the dynamic key the Common Cipher Key CCK and the Group Cipher Key GCK TETRA DMO has two classes of encryption Class and Class 2 The security features supported in the radio depend on the security mode Table 2 2 Security Features Required Per Security Class Security Feature Radio Initiated Authentication SwMI Initiated Authentication Mutual Authentication OTAR SCK AIE DCK AIE GCK AIE Mode Security Class 1 Security Class 2 Security Class 3 Not Allowed Not Allowed Not Allowed Optional Optional Mandato
151. set to more than 0 Duplex Ring Muted Indicates that duplex ring volume is set to 0 and simplex ring volume is set to more than 0 Vibrate On Indicates that the radio vibrates to alert you of an incoming call Vibrate then Ring Indicates that the radio vibrates and rings to alert you of an incoming call Low Audio Indicates that the audio mode is changed to low High Audio Indicates that the audio mode is changed to high Earpiece Connected Indicates that the earpiece is connected 3 11 TETRA Radio Product Information Manual Table 3 6 Status Icons cont d 3 12 Icon SO Y K l O a mam El po ze Description GPS Indicates that a valid location coordinates are received RUI Logged on Indicates that you are logged on into the radio RUI Pseudo Log On Indicates that you are in pseudo logged on state RUI Packet Data Indicates Pseudo Log On state when the Packet Data feature is activated and active data session is in progress RUI Packet Data Indicates Pseudo Log On state when the Packet Data feature is activated and the external device sets up data connection with the radio Battery Strength Shows the charge of your battery Battery Charging Indicates that the battery is charging Emergency Appears while the radio is in Emergency Operation Disaster Alert Call Appears while the radio is in the Disaster Alert Call List Scrolling Displayed to ind
152. solutions com Service Information AME This topic contains contact details to service centers in Asia and Pacific region Technical Support Technical support is available to assist the dealer distributor in resolving any malfunction which may be encountered Initial contact should be by telephone wherever possible When contacting Motorola Technical Support be prepared to provide the product model number and the serial number Further Assistance from Motorola You can also contact the Customer Help Desk through the website http www motorolasolutions com tetra Ifa unit requires further complete testing knowledge and or details of component level troubleshooting or service than is customarily performed at the basic level send the radio to a Motorola Service Center as listed in the following table Service Information Telephone Numbers and Addresses of the Asia and Pacific Motorola Centers Country Telephone Number Address Singapore 65 6352 6383 Motorola Solutions Singapore Pte Ltd c o Azure Engineering 49 Jalan Pemimpin 03 11 APS Industrial Building Singapore 577203 Contact Mareen Phua E mail mareen azure com sg Enquiry Tay Yong Hock E mail yonghock tay motorolasolutions com Malaysia 603 7809 0000 Motorola Solutions Sdn Bhd Level 14 Persoft Tower No 68 Pesiaran Tropicana 47410 Petaling Jaya Selangor Darul Ehsan Malaysia Contact Koh Tiong Eng E mail A21001 motorolasolutions c
153. stantly calculates a normalized value that represents the signal strength of a cell This value is used by the radios to determine if the cell is usable and when to leave the cell In the default case when the radio is camped on a cell it will initiate link failure procedures i e leave the cell if this normalized signal strength value falls below zero However via the CPS it is possible to configure the radio to allow this normalized value to be processed below zero value can be set in 1db steps up to 5db Reducing this value below zero will allow the radio to maintain service on a very weak cell where the radio is unable to roam to a better cell 2 18 Supplementary Services Following is the description of the TETRA Supplementary Services SS that the radio supports in the TMO 2 18 1 Ambience Listening The Ambience Listening AL allows a console operator or dispatcher to monitor audio activity in the vicinity of a specific radio without giving any indication to the affected radio When the radio receives a call setup message with an AL call the radio accepts the call Then the radio opens the microphone and begins transmitting without showing any indication of the call Call acceptance and rejection while active in another call follows the PPC rules The radio imposes no time limit on the transmission The radio continues to transmit until the SwMI ends the call or the user performs an action that releases the call If the user attempt
154. t The features are enabled at the same time the customer programs the radio The enablement for all the selected features is performed in one operation TETRA Radio Product Information Manual 1 4 Ordering Software Enablement Kit Procedure Steps 1 Order the standard software enablement kit main kit GM0127 2 Add software feature options Y NOTE You can select more than one feature for each main kit 3 Order quantity equaling number of models requiring an option 1 5 Radio Ordering Procedure Steps 1 Order the main radio model 2 Order options from each of the categories e Software Selling Features e Customer Programming Software e Integrated Terminal Management Accessories y NOTE Export controls apply when ordering encryption 1 6 Golden Codeplug The Golden Codeplug covers all standard codeplug fields and required optimal settings In a Golden Codeplug field parameters are pre configured and fine tuned for high quality and to get better performance from your new radio 2 Services and Features 2 1 Features Overview Trunk Mode Operation TMO Air Interface Encryption SCK CCK DCK GCK Air Interface Migration Ambience Listening Announced Type 2 handover AT commands Broadcast Call Congested Cell Handling DGNA Individually and group addressed Dynamic Key Encryption Emergency group call Group call Hot Mic and Alternating Hot Mic Multi Network Operation Mutual Authentication
155. t available The radio registers to any network that it finds that is already programmed into its codeplug list of networks i e no user manual selection is required Network selection to another network is only performed at initial cell selection following a link fail and then only if the home network is not available The radio uses its own ISSI The radio operates in all networks as it does in its home network All calls are placed using SSI addresses and it is the SwMI responsibility to reject calls for subscribers or groups that cannot be reached in the local system y NOTE The telephony gateway interprets telephone numbers with the country code of the local country For example if you dial the number 01256 48 4566 in the UK it is treated as if you dialed 44 1256 48 4566 For description of other migrating modes used when migration is supported by the BTS refer to Air Interface Migration and Dynamic Air Interface Migration sections 2 17 4 Registration On camping on a cell the radio sends a registration request PDU to the SwMI which includes a request to attach to the selected talkgroup If the registration and attachment succeeded the radio begins normal operation on the cell If the registration attempt times out or the SwMI rejects the registration for a temporary reason another registration attempt is made If both attempts fail the radio attempts to camp on a different cell If the SwMI denies the registration request
156. ter Site or Mobile Switching Office Class 3 DCK encryption ESI with CCK authentication Clear Not encrypted Common Cipher Key CCK Used to encrypt group and broadcast addressed downlink signaling from infrastructure to a radio Also used to protect ISSI identities SEE ALSO Encryption Individual Short Subscriber Identity Control Channel The always active control channels transmit and receive the signaling to monitor and control the operation of radios CPS Customer Programming Software Customer Programming Software CPS The software application used for programming radios DCK Digital Car Kit DCK Derived Cipher Key Derived Cipher Key DCK Used to encrypt all uplink signaling from radios to infrastructure and individually addressed downlink signaling from infrastructure to a radio SEE ALSO Encryption DGNA Dynamic Group Number Assignment Direct Mode Operation DMO Direct communications between two or more radios without the use of any infrastructure DMO Direct Mode Operation Appendix B Glossary DTE Data Radio Equipment DTMF Dual Tone Multi Frequency Dual Tone Multi Frequency DTMF Tone based signaling scheme which combines two of a set of standard frequencies The result is a third or beat frequency signal which is the desired or usable signal DTMF signaling is used as tone dialing in the common telephone Dynamic Group Number Assignment DGNA DGNA is a possibility to prov
157. the Air Rekeying OTAR of the CCK by the system A clear radio can set up calls to and receive calls from encrypted radios The system informs the encrypted radios that the call is with a clear radio and they switch to clear operation Class 2 and 3 radios can only act as described if they are allowed to operate in a lower class 2 14 4 4 Group Cipher Keys Encryption Class 3G For the Security Class 3G the system allows grouping addressed signaling and dedicated group call traffic encryption using GCKs to cryptographically isolate talkgroups The downlink signaling is encrypted using MGCK that is cryptographically derived from the CCK associated with the serving cell and the GCK associated with a given talkgroup The SwMI does not change GCK and CCK simultaneously Whenever a GCK change occurs CCK changes are frozen for this time period The DCK is derived from either the one way or mutual authentication process and the CCK is received during registry whereas the GCK is received through OTAR mechanism only TETRA Radio Product Information Manual The radio supports over the air and manual provisioning of key associations that link a GCK to one or more TMO talkgroups and manual provisioning of KAG to one or more DMO talkgroups The system can provide the ability for the operator to group contiguous ranges of TMO SSI This case occurs where any talkgroup residing within the address range is assigned using the same GCK association These ranges
158. the copyrights patents or patent applications of Motorola except for the normal non exclusive license to use that arises by operation of the law in the sale of a product ix Service Information EIA This topic contains contact details to service centers in Europe Middle East and Africa European Radio Support Centre ERSC ERSC provides a remote Technical Support Service to help customers resolve technical issues and quickly restore their systems This team of highly skilled professionals is available to the customers that have current ERSC service agreements in place For further information and to verify if your current service agreement entitles you to benefit from this service contact your local customer support To contact ERSC use the following EIA Integrated Call Center details E mail ersc motorolasolutions com Telephone 49 30 66 86 1555 Service Information Telephone Numbers to EIA Integrated Call Center Country Telephone Number Austria 01206091087 Denmark 043682114 France 0157323434 Germany 06950070204 Italy 0291483230 Lithuania 880030828 Netherlands 0202061404 Norway 24159815 Portugal 0800552277 Russia 810800228 41044 Alternative 8108001201011 Saudi Arabia 8008445345 South Africa 0800981900 Spain 0912754787 United Kingdom 02030277499 Other Countries 42 0533336946 European Systems and Components Centre ESCC ESCC provides a repair service for infrastructure equipment Cust
159. this call receive the channel busy indication The radios are identified using their radio numbers 2 10 1 Simplex Private Call The radio is able to make and receive private calls to and from other TETRA radios with simplex speech capability This call type uses TETRA individual call signaling All private calls are initiated using the on off hook method For incoming calls the radio accepts both direct and on off hook setup 2 10 2 Duplex Private Call The radio allows making and receiving private calls to and from other TETRA radios with duplex speech capability Depending on the configuration the radio may prohibit you from initiating duplex private calls The radio always initiates duplex private calls using on off hook signaling with the traffic channel allocated by the SwMI only after the called party has answered the call Therefore the radio generates all progress tones during the call setup In addition the radio allows the SwMI to modify the call setup to direct This modification enables the infrastructure to generate the progress tones TETRA Radio Product Information Manual 2 10 3 Talk Time Limit In a simplex call the radio limits the time you can continuously talk in a group call without interruption according to a provisioned value You are warned a short time before the talk time expires The timer is provisioned per talkgroup folder In a simplex call the radio limits the time you can continuously talk in a group c
160. tion Manual 2 10 8 DMO Individual Only Talkerouns rr nnnrnnrrnnnnnnnrnaninnanns 2 15 Doll A O 2 15 XPA Initiating a Ebert alter 2 16 211 2 Recervinga Phone a dees deed See eege e 2 16 ZE Call Restoration in Phone Call lia 2 16 2 12 Emergency Operations a a das 2 16 212 Emergency Group Calle ccoo EAR 2 17 2 12 2 Non Tactical Emergency oses einne e a sida ceccdeuia scccdettnc cucesvual ovcdasdaceeceduns cocdeeievecuaeacnedse 2 17 2 12 3 Emergency Individual Calls Private or MS ISDN cece eeeeeeeeeeeeeeeeeeneeeas 2 17 e Bimvergency E WEE 2 18 2121 Emergency SDS Status id a a EE EE SE EE Eed 2 18 2 12 6 Emergency Hot Microphone maes 2 18 2 12 7 Alternating Hot Microphone casses eeo ae cece G ea aeaa ea aE a a E e eSa 2 18 20128 Silent Emergency Mode ccoo ia tt 2 19 STE Invisible Emergencia IA ce EGA 2 20 212 107 Disaster EE 2 20 213 Short Data Services Deh A A DEE Ee 2 20 ISI CS tats Messa Sc a A A Aia 2 21 2352 TEXC MESSAGES A A Eed AE 2 22 2 13 2 1 SDS Messages Concatenaton nono sees Ea E Sa i Seiat 2 23 2 133 Immediate Text Messages 2 Ziele in 2 23 2 13 4 Home Display Text Message sit cree A a EES 2 24 2 13 5 Predefined Templates ATS Entry Brommt 2 24 2 13 6 SDS Air Interface Aspect traicionada 2 24 yA ES O A cece EE EEE EEN EE ET OE ET E E ET sag caves avedeccsesvasceuseaveesee 2 24 2 13 7 1 SDS End to End Encryption eners n e EEE E E S EaR 2 25 213 8 Store and Forward onse rea ienei A AAA AE
161. tput Group Call An instant communication between users that belong to the same talkgroup SEE ALSO Talkgroup Group Cipher Key GCK Predetermined cipher key used to provide confidentiality in Class 3 system with corresponding algorithm Used to generate MGCK SEE ALSO Modified Group Cipher Key Class 3 Group Short Subscriber Identity GSSD TETRA term in Dimetra called Group ID or Talkgroup ID SEE ALSO Short Subscriber Identity GSSI Group Short Subscriber Identity Home Location Address Area within radio coverage of a base station or group of base stations within which a radio is allowed to operate SEE ALSO Base Station Appendix B Glossary Individual Short Subscriber Identity ISSD TETRA term for a unique individual ID assigned for each radio SEE ALSO Short Subscriber Identity Individual TETRA Subscriber Identity TSI Consists of ISSI plus MCC and MNC codes SEE ALSO Individual Short Subscriber Identity Mobile Country Code Mobile Network Code ISSI Individual Short Subscriber Identity ITSI Individual TETRA Subscriber Identity Key Each device involved in secure communications is loaded with a multi digit encryption variable an encryption key An encryption algorithm built into the device uses this key to encrypt voice or data as needed Only devices in the system with the same algorithm and encryption key can decode the encrypted signals SEE ALSO Encryption LIP Lo
162. ty Each talkgroup entry contains a TETRA group address and may be associated with a name tag The talkgroups can be defined in the codeplug as per the radio capabilities Talkgroups are configured separately for TMO and DMO modes To program a talkgroup in TMO define its name and GSSI To program a talkgroup in DMO define its name GTSI and frequency The radio operator can select a talkgroup which has an associated TMO or DMO frequency depending on the mode selected When switching between the TMO and DMO modes the last active talkgroup is selected However the required talkgroup can be mapped in CPS In such a case a corresponding talkgroup is automatically selected during mode switching irregardless of the previously selected talkgroup Y muaa Neither the group name nor the corresponding group address can be edited using the radio MMI 2 9 2 Talkgroup Selection 2 9 2 Talkgroup Selection Talkgroup selection from the stored talkgroups list in the idle mode can be performed by scrolling through the list using the scroll keys or the talkgroup rotary knob Talkgroup scrolling can be provisioned to scroll in a folder only or continuously through the folders acting as one continuous list of groups The radio does not allow directly dialing a group SSI 2 9 3 Favorite Folders You can add frequently used talkgroups and phone book contacts to the Favorite folder You can add items from Favorites or Talkgroups and Contacts menu levels respecti
163. ures are impacted e No other services except emergency are allowed same as in emergency mode e Hot Mic functionality cannot be used e When Announcement Call begins any other ongoing services are terminated If the type of the encryption is defined by the BSI feature radio with a SIM Card the Broadcast Call is always clear Otherwise if the radio uses other encryption service the type of the encryption used for that call is up to the encryption settings of that service Not all infrastructures support this feature Consult your service provider before enabling it 2 9 15 PTT Double Push 2 10 PTT Double Push D PTT lets the radio user send a tone to other users on the same talkgroup as a way of attracting attention before transmitting voice or as a signal instead of speech for example as confirmation of message received The D PTT tone can be configured as single double or triple in the radio setup menu 2 9 16 PTT Queue Y muaa The D PTT tone is sent as voice so 1t only needs to be configured on the sending radio All radios attached to the same talkgroup as the sender receive it regardless of having D PTT enabled 2 9 16 PTT Queue This feature allows you to configure the response to releasing PTT of the call originating radio This determines how to cancel waiting for the call when the infrastructure is busy and your call is queued 2 9 17 Talking Party Identification The PDUs and facility elements for these TETRA Suppl
164. ures as described in the TETRA Security ETS 300 392 7 standard TTR 001 11 TIP and TTR 001 13 TIP 2 14 1 Terminal Equipment Identity The Terminal Equipment Identity TED is unique identification number programmed in the radio at the factory and cannot be later modified 2 14 2 PIN PUK User Authentication In order to authenticate yourself the radio supports a Personal Identification Number PIN and PIN Unblocking Key PUK mechanisms These mechanisms prevent from an unauthorized access to the radio The PIN PUK operations are available from both MMI and PEI using AT commands For the authentication purpose the radio prompts you to enter a valid 4 digit PIN before the radio allows to access all the available services The PIN is defined in the codeplug If the maximum number of consecutive failed attempts is reached the radio is blocked and remains in this state until unblocking The permissible number of consecutive failed attempts is defined in the codeplug The blocked status is sustained regardless of turning off or battery removal When the radio is PIN locked you have no or limited access to the radio services The PIN is defined in the codeplug The radio is unblocked either by entering the PUK or by using the CPS The PUK can be entered through the MMI or through the PEI The PUK is defined in the codeplug 2 14 3 Authentication Authentication establishes a level of a trust between a radio and SwMI It is a challenge respon
165. vel based algorithm is in the place Depending on the level of congestion the terminal is waiting for the registration or is rejected on that cell The terminal recognizes whether the cell is congested Control Channel Congestion The terminal tries to roam to not congested cells first ranking congested ones as secondary The cell congestion is one of the service level criteria The following cells are never marked as congested e Last suitable cell if there are no other suitable cells during roaming or initial cell selection e Serving cell The feature is configurable using the CPS 2 17 11 Subscriber Class 2 17 11 Subscriber Class When the radio powers up or whenever it performs registration or roaming it always uses its provisioned Subscriber Class SC When the radio registers on a cell that does not support any of its SCs it is active only in services that have the emergency priority Whenever the radio SC does not match the cell SC the feature is configurable using the CPS e the radio uses normal ranking procedures see section Roaming e does not roam to the cell at all 2 17 12 Subscriber Class by Talkgroup The Subscriber Class by Talkgroup feature forces all the radios attached to the same talkgroup to have the same Subscriber Class The Subscriber Class by Group feature helps to avoid issues as presented in the following scenarios e Preserving traffic channel capacity For two cells having the same cov
166. vely This feature allows a quick access to frequently used talkgroups by including the groups in up to three favorite talkgroups ranges These ranges are separately stored in the data storage The feature operates in both TMO and DMO modes The favorite talkgroups ranges are shared for TMO and DMO talkgroups You can select view and edit My Groups ranges Once a group from the My Groups range is selected you can select any of the favorite talkgroups in that range using normal procedure A favorite talkgroup range name replaces a talkgroup range name on the radio display whenever a favorite talkgroup is selected or is in use for appropriate operation The ranges of favorite talkgroups with their talkgroup assignments are kept through the radio power cycle 2 9 4 Talkgroup Blind Operation The radio can be provisioned with a virtual rotary end stop option for use in blind operation When you have scrolled to the beginning or the end of the list the first or the last talkgroup is displayed even if you continue to scroll To change this setting for the rotary knob you can select Wrap around Rotary Knob Group Scrolling option in the CPS 2 9 5 Receive only Talkgroups Talkgroups can be provisioned as receive only talkgroups This setting depends on the settings of the folder the talkgroup is in Any talkgroup from the receive only folder can be selected The radio allows to receive calls however no call can be initiated to this talkgroup
167. wn feature is based on a sensor with low power current consumption When Man Down is enabled the sensor performs a self test during powering on the radio If the test fails the radio notifies with a specific audio tone and status icon The radio also notifies with the specific audio tone and status icon when the man down device detects a failure during the activation of the feature If the feature is deactivated using radio MMI after the sensor failure is detected the man down icon disappears and the tone is no longer played Depending on the CPS settings additional audio and or visual indications are available to help locating the radio In such case if the man down alarm is activated emergency alarm started the radio starts additional audio indication playing high and low frequency sounds continuously with highest possible volume The radio display and or keypad may also start blinking If the emergency hot microphone is on the additional audio indication is not played 2 20 Repeater Mode 2 50 The Repeater Mode provides repeater connectivity between radios operating in the DMO Mode Y muaa Only the radios on the same talkgroup can communicate with each other through the repeater 2 21 2 21 DMO Gateway and Repeater Communication Figure 2 5 Repeater Mode Operation DMO DMO A DMO repeater is used to extend the DMO range by retransmitting received information from one radio to another It retransmits group calls private c
168. y be performed at the factory or at the appropriate Motorola Repair Center Component replacement can affect the radio tuning and must only be performed by the appropriate Motorola Repair Center All orders for parts information should include the complete Motorola identification number All part orders should be directed to your local AAD office See your latest price pages Parts Identification and Ordering Request for help in identification of non referenced spare parts should be directed to the Customer Care Organization of Motorola local area representation Orders for replacement parts kits and assemblies should be placed directly on Motorola local distribution organization or via Motorola Online Extranet Service Information Americas This topic contains contact details to service centers in Latin America and Caribbean region Technical Support To request technical support go to https businessonline motorolasolutions com Contact Us Some replacement parts spare parts and or product information can be ordered directly If a complete Motorola part number is assigned to the part it is available from Motorola If no part number is assigned the part is not normally available from Motorola If the part number is appended with an asterisk the part is serviceable by Motorola Depot only Ifa list of parts is not included that means that no user serviceable parts are available for that kit or assembly Warranty and Repairs

MTP6550/MTP6750 Product Information Manual

Contents

Download Pdf Manuals

Related Search

Related Contents