User manual
Contents
1. Optoma Projector Flush Mount Model OCM818W OCM818B Patent Pending Revision 04 01 2012 Optoma Europe Limited www optoma eu User Operation Guide Thank you for purchasing the Projector Flush Mount This bracket is suitable for most projectors up to a load of 15kg To ensure correct usage please read this instruction manual thoroughly Keep this manual for future reference BRACKETS SHOULD BE MOUNTED ONLY BY A QUALIFIED INSTALLER User will be responsible for any injuries and damages that may arise from improper installation and handing of Projector Flush Mounting Kit Ensure all mounting screws are appropriately positioned and properly tighten fastened Installers are to ensure customer s safety during installtion We reserve the right to amend or undertake any necessary changes without prior notice Ensure the Ceiling can support the total weight of the Projector and the Projector Flush Mount All bolts and screws must be used at the designated points as per installation instructions to prevent damage to the projector unit or injury DO NOT install near an air conditioner or where there is excessive dust and smoke Please read these instructions before commencing installation as faulty installation could result in injury Optoma assumes no responsibility for faulty installations Parts Bag oy Ge naas M4 x 15 Cross M3 x 15 Cross AE A A Recessed Screw 4PCS a Recessed Screw2. User Operation Guide E Adjusting the Projector Roll Shift Adjustments to make Roll Shift adjustments first ensure the weight of the Projector is supported Then loosen the M8x65mm Socket Cap Screw with the supplied 6mm Allen Key and adjust to your desired position Re tighten the screws firmly Socket Cap Screw Mi Shift Pitch Adjustment to make Pitch adjustments first ensure the weight of the Projector is supported Then loosen the M8x15mm Socket Cap Screws with the supplied 6mm Allen Key and adjust your projector to the desired position then tighten the screws firmly 6mm Allen Key Ik NG NP TA SA AHA NS Optoma Sa a ee a a a Specifications are subject to changes without notice 11 Optoma Due to continuing product development the manufacturer reserves the right to alter specifications without notice Published 04 01 2012
3. 4 PCS 5 EE M4 x 20 Cross M3 x 20 Cross E B Recessed Screw 4PCS b Recessed Screw 4 pcs c Lips eee 4 pes M3 Flat Washer 4 pcs M5 x 15 Cross Extension D mum Recessed Screw 4PCS d Bracket 50mm 4 PCS M5 x 20 Cross E mmm Recessed Screw 4 pcs M5 x 25 Cross Tools Included F mmm Recessed Screw 4 pcs M6 x 15 Cross Allen K 1 G mm Recessed Screw 4 pes TIARE pe M6 x 20 Cross R Recessed Screw T PF 6mm Allen Key 1 pc Flush Mount Assembly x1 M6 x 25 Cross Ba Recessed Screw PSS Tools Reguired for mount assembly J immWasher 4 PCS 4 4x Star Philips Screw Driver 2 1x 13mm Spanner K 2mm Washer 4 pcs L 4mm Washer 4 pcs M Bottom Spacer 4 pcs N1 M5 x 10 Socket 4pcs P Button Screw p N2 SJ Square Nut 4 pcs Ceiling Plate Pa g gt k 5 st M4x6 Cross R d b gt Ka ross kKecesse Ay M8x65 Socket Cap lt 4 ae Screw f s Cross Recessed ix LI M5x10 Socket Screw A I EEr o HA Button Screw 1 i m P I Sego Ta Ne ed i i a xtension Bracke u 100mm IG i ply Extension Bottom Spacer ct Bracket 50mm 1 Imm 2mm 4mm Washers Specifications are subject to changes without notice 3 Optoma User Operation Guide A Removing the Ceiling Plate from the Flush Mount Assembly 1 Loosen the M4x6 x2 Cross Recessed Screw with a screw d
4. river 2 Remove the M8x55 Socket Cap Screw and Nylock Nut from the Flush Mount Assembly as shown 3 Removing the Ceiling Plate from the Flush Mount Assembly M8x55 Socket Cap Screw Ceiling Plate M8 Nylock Nut M4x6 Cross Recessed Screw Screw driver 6mm Allen Key B Installing the Ceiling Plate 8mm 5 16 Holes Nylon Anchor Plug Ceiling Plate Washer TN 14 Gauge Coach Screw NX Plaster Board 3mm 1 8 Holes drill on Timber Beam Ceiling Plate Washer _ 14 Gauge Coach Screw Plug and Screws are only for recommendation not supplied within package Specifications are subject to changes without notice 5 User Operation Guide C Attaching the Flush Mount Assembly to the projector C 1 Loosen the M5x10mm Socket Button Cap Screws using the 3mm Allen key until you can slide the extension brackets freely as shown Extension Bracket 100mm Cap Screw C 2 Place projector s Flush Mount Assembly over the projector and align the centre of the Flush Mount with the projector s approximate Centre of Gravity This surface to be ap proximate parallel to the projector front Optoma C 3 Place the Bottom Spacers in between the Extension Brackets and the Projector and align the mounting holes as shown below Extension Bracket NOTE i If the mounting holes on your projector i Extension Bracket are recessed you may need to use the additional space
5. rs supplied in the parts bag Please select the appropriate spacers according to the design of your projector Recessed Mounting Hale Bottom Spacer Spacer M5x10mm Note 2 If you cannot align the 100mm Extension Bracket to the mounting hole on your projector you may need to use the additional 50mm Extension Brackets shown in the diagram on the right Extension Bracket Square Nut Bottom Spacer Specifications are subject to changes without notice 7 User Operation Guide C 4 Select the correct Mounting Screws from the Parts bag and firmly screw the Flush Mount Assembly onto your Projector Once this is done the Projector Flush Mount Assembly is ready to be mounted onto the Ceiling Plate Mounting Screws alk Bottom Optoma D Attaching the Flush Mount Assembly to the Ceiling Plate D 1 Connect the Short Pole to the Ceiling Plate as shown be Ceiling Plate Short Pole D 2 Insert the M8x55 Socket Cap Screw into the slot on the Ceiling Plate to lock the Flush Mount Assembly with the M8 Nylock Nut Tighten the M4x5 Cross Recessed Screws to balance the Flush Mount Assembly M8 Nylock Nut and Washer M8X55 Socket Cap Screw and Washer Driver 6mm Allen Key M4X6 Cross Recessed Screw Tip When the Projector required servicing remove the Projector via the easy disconnection point to save time Specifications are subject to changes without notice 9
Download Pdf Manuals
Related Search