PowerPlay Compression Pump User Manual
Contents
1. circuitry 1 Intended Uses The PowerPlay is an intermittent compression device used with inflatable wraps to simulate stroking and kneading of the tissue by the hands This massaging action aids in the temporary relief of minor muscular aches and pains and increases circulation in the treated area Contraindications The PowerPlay PPRT 01 mustnotbe used totreatthe following conditions e Persons with suspected active or untreated deep vein thrombosis ischemic vascular disease severe arteriosclerosis pulmonary edema congestive heart failure thrombophlebitis or an active infection e Ona leg where wraps would interfere with the following conditions vein ligation gangrene dermatitis open wounds a recent skin graft massive edema or extreme deformity of the leg e On persons with neuropathy e On extremities that are insensitive to pain e Where increased venous or lymphatic return is undesirable Default Settings Treatment time each port eeseeseesessessessecsessssssessestessessessssnesseasees 20 minutes Internal Safety Valve Relief PreSSUre ssssssssscssesecseesesseesesseeeee 100 mmHg Warnings and Precautions WARNING Do not open or remove covers No user serviceable parts inside Direct all service needs to FIG LLC Inc WARNING If pulsations numbness or throbbing occur the wrap may be wrapped too tightly Loosen immediately WARNING Stop using device if swelling occurs consult ph2. period At this stage the battery charger MUST be connected immediately to avoid any interruption in the treatment session STAGE 3 If the battery voltage drops to a critical level at any time the yellow LED will illuminate AND the display will show BL In addition the audible alarm will sound and cycling of the pump will be inhibited The unit will then automatically shut off after two minutes A fully charged battery will operate a single PowerPlay wrap for approximately 4 6 hours Less operating time between charges should be expected when using larger and or multiple wraps Using the AC Adapter Battery Charger Insert the supplied power plug into the adapter jack on the pump unit and connect the power adapter to the main voltage wall socket The battery charge LED will illuminate RED while charging battery and turn GREEN when charge is complete It will not be illuminated if the charger is not connected For extended operation periods or to charge the battery during treatment sessions the AC adapter can be connected while the device is in use 10 Troubleshooting Cleaning and Disinfecting NOTE Inspect the PowerPlay unit and follow the cleaning and disinfecting procedures prior to each use WARNING Device must be turned off and disconnected from the power mains wall outlet prior to and while cleaning or disinfecting CAUTION Do not place any items in an autoclave CAUTION Do not immerse pump unit i
3. the port will beep and flash to on the display as well as flash the indicator light on that port for 1 5 seconds That port will then shut off If multiple ports are activated the above procedure will cycle for each port When the last port is cycled through and is off the alarm will sound for 15 seconds and the entire unit will shut off Note that if a port is shut off and then reactivated the time is reset to 20 minutes 7 To turn off the pump unit depress and hold the power button for 1 2 seconds 8 To disconnect the air tube from pump unit depress the metal thumb tab on the connector while pulling the tube away Alarms HI KINKED HOSE If pressure limit is reached in less than 2 seconds after pump is energized cycling stops the alarm sounds and display reads HI for a period of 1 5 seconds The unit then proceeds into the next output phase of that cycle This will repeat until a THIRD HI alarm condition at which point the alarm sounds display flashes HI and all functions are inhibited for that port except 1 0 In addition the LED indicator coinciding with whichever wrap was energized when the condition occurred flashes rapidly LO LEAK When a wrap is activated if pressure limit is NOT reached within 5 minutes after pump is energized cycling stops the alarm sounds and display reads LO for a period of 1 5 seconds The unit then proceeds into the next output phase o
4. F e Do not unroll or attach the wraps in below freezing temperatures 0 C 32 F as damage to the air bladders can occur making them unable to hold pressure e Store in a dry location between 10 C 50 F and 40 C 104 F 30 75 relative humidity e Limit Transport Temperatures to between 20 C 4 F and 60 C 140 F e Normal Operating Conditions Temperature Range 10 C 50 F to 40 C 104 F Relative Humidity 30 to 75 Purpose of this Device The purpose of the PowerPlay PPRT 01 when used with PowerPlay site wraps is to provide relief from minor muscle pain while temporarily improving blood circulation to the area This is accomplished by an electronically controlled intermittent compression pump unit delivering air to the wraps that in turn compress the tissue in the treated area by simulating stroking and kneading by the hands The pump unit will inflate the wraps to a specified pressure of 50 mmHg 55 mmHg 60 mmHg 65 mmHg or 70 mmHg set by the user and once the pressure is reached it will hold for 10 seconds before releasing Cycles are repeated for 20 minutes or until the unit is turned off Internal rechargeable batteries allow the system to be completely portable thus preventing interruptions in treatment Set Up Instructions 1 Remove items from packaging and plastic bags 2 Inspect all components for damage If any parts appear damaged or are inoperable contact PowerPlay Custom
5. Power Play Muscle Massager Manufactured for Customer Service FIG LLC Toll Free 1638 South Main Street 855 PWR PLAY Tulsa OK 74119 USA 855 797 7529 Email info powerplay us Document IFU PPRT 01 Copyright 2012 FIG LLC JV rowenPLay Disposal e Pump control unit contains rechargeable batteries Do not discard the pump unit in regular waste Bring the unit to your local recycle center or return to FIG LLC O The use of accessories power supplies and cables other than those specified with the exception of components sold by the manufacturer of the PowerPlay PPRT 01 as replacement parts may result in increased emissions or decreased immunity of the PowerPlay PPRT 01 Class II medical electrical equipment Oo LY This unit is an electromechanical device that includes printed BY circuit boards and rechargeable batteries Do not discard in landfill Consult local state federal and country requirements for proper disposal instructions 5 This symbol designates the degree of protection against electrical A shock as being a type BF applied part Customer Service Toll Free 855 PWR PLAY 855 797 7529 Email info powerplay us FIG LLC 1638 South Main Street Tulsa OK 74119 USA IFU PPRT 01 Technical Data Specifications MAIN UNIT Dimensions seceseeeeeeeeee 6 9 x 4 3 x 1 8 inches 1 75 x 1 1 x 4 6 centimeters Weight oesie eenn n om Approximately 1 1 Ibs 0 50 kg Mode of Oper
6. ations scscscscsssicscosccevescciesccssersseesccessscesvoresaee esvoveeeteseseennewceseeess Cyclic Source Of POWEM cesscesseesseeseeees 6 Volt 2 0 Ah NiMH rechargeable battery CAUTION Charge batteries using only the power supply provided by FIG LLC POWER LO Ufa i S EEEE ogee ane tre oa Ran ener AEE 10 Vdc 1 1 A Mode of Operations s cccicccsicescssscsaccssscescsectasssecssescscttaviestesentnneivteas antes Continuous SYSTEM OPERATING ENVIRONMENT Temperature ccescessessessessecsessssssssssseessstessesseesesseesees 10 C 50 F to 40 C 104 F PUTING LY aer A 30 to 75 FACTORY SETTINGS Pressure selectable 50 mmHg 55 mmHg 60 mmHg 65 mmHg 70 mmHg Treatment Time for each OUTPUT eeseeceeceeseesseeseestesseesessesseesteseesteees 20 minutes TOLERANCES POSS URC canm E E ER 5 This device is not protected againstthe ingress of water ordinary protection IPX0 Equipment is not suitable for use in the presence of flammable anesthetic mixture with air or with oxygen or nitrous oxide The rechargeable batteries supplied in this unit are not field replaceable Return unit to FIG LLC if batteries require replacement NOTE Recharge batteries every 60 days when unit is not in use in order to maintain battery integrity Batteries can be recharged approximately 500 times between replacements Battery charge from depleted state takes approximately 4 hours and is terminated automatically by the control
7. e control panel Note that an activated port begins with a preset pressure of 50 mmHg 4 Press the Port Set Pressure button of any active port again to set pressure to 55 mmHg press for 60mmHg then to 65mmHg and again for 70mmHg Pressing a fifth time will turn that port OFF 5 Note Adjustments can be made at any time that the pump is at rest i e before cycling begins or during rest periods between wrap inflations When a wrap is being inflated a slow flashing of the corresponding port indicator indicates the active port If adjustments are made during a rest period the unit will resume cycling at the end of that rest period The number of wraps selected determines the rest time In a single port mode Port 1 Port 2 OR Port 3 only modes the rest period is about 21 seconds from the time that the pressure is reached and the pump is turned off until the time that the wrap is re pressurized In a dual port mode any 2 ports active the rest period is about 12 seconds from the time the pressure is reached and the pump is turned off until the time the next wrap is pressurized In the triple port mode Port 1 AND Port 2 AND Port 3 the rest period is about 12 seconds from the time the pressure is reached and the pump is turned off until the time the next wrap is pressurized This timing ensures that each wrap is being deflated for approximately 30 seconds thus allowing ample rest time between compressions on t
8. er Service front cover 3 Before using connect the supplied power adapter plug into the jack on the pump and plug into the main wall socket The LED CHARGE indicator will turn RED during the charge cycle and GREEN when the charge is complete The unit may be used while connected to the charger but should be disconnected from the charger when the charge is complete 4 Uncoil the tubing being careful to remove any kinks from tubing due to compacting in shipping 5 Apply wraps according to the instructions in the wrap packaging route tubing in a manner to prevent a tripping hazard and to avoid kinking 6 Connect wrap air tubes s to pump air outlets WARNING If pulsations numbness or throbbing occur the wrap is wrapped too tightly Remove the wrap and re wrap for comfort If pain or swelling occurs discontinue use and notify your medical professional immediately Operating Instructions 1 After following the set up instructions ensure that the wraps are snugly and securely fastened as indicated in the instructions for the wrap 2 To turn the system on press the Power button If the unit will not power on connect the wall supply to charge the battery Unit may be used while battery is being recharged 3 The display will show On Press the port button associated with the port where wraps are connected The active port will be indicated by the illumination of the corresponding function indicators near the bottom of th
9. f that cycle This will repeat until a SECOND LO alarm condition at which point the alarm sounds display flashes LO and all functions are inhibited except 1 0 In addition the LED indicator coinciding with whichever wrap was energized when the condition occurred flashes BL BATTERY CRITICAL If battery voltage drops to a critical level cycling stops audible alarm sounds and display flashes BL In addition the LOW BATTERY LED indicator will be illuminated To reset an alarm condition the unit must be turned OFF If not manually turned OFF within 2 minutes of an alarm condition occurring unit automatically turns itself OFF See trouble shooting section for resolving these alarms If you encounter any problems that cannot be resolved by the preceding information contact PowerPlay Customer Service at 855 PWR PLAY 855 797 7529 13 Low Battery Indicator In order to ensure that proper pressure is always reached during operation regardless of the charge state of the battery there are THREE stages of the LOW BATTERY INDICATOR as follows STAGE 1 The yellow LOW BATTERY INDICATOR illuminates when the pump is NOT RUNNING turns OFF when the pump starts and illuminates again when the pump is in the REST period This is the FIRST indication that a recharge is needed at the earliest opportunity STAGE 2 The yellow LOW BATTERY INDICATOR will REMAIN ILLUMINATED during both the pumping time and the rest
10. he affected area It should be noted that the inflated wraps exhaust during the rest 8 User Maintenance NOTICE Contains no serviceable parts Contact PowerPlay Customer Service e Inspect the unit and all components for any damage that may have occurred during shipping or general handling prior to each use for example frayed or cut cord split air tubes cracked plastic housing damaged LED display torn wrap etc Do not attempt to connect the wall supply if any damage is noticed Avoid subjecting the unit to shocks such as dropping the pump unit Notify FIG LLC for immediate replacement of any damaged items Do not handle the wraps with any sharp objects If a bladder is punctured do not attempt to repair the wrap Replacement wraps are available for purchase at www powerplay us or by calling 855 979 7529 e Roll wrap for storage amp transportation avoid folding or creasing the bladder e Battery is not replaceable return unit to FIG LLC if service is needed e Contact PowerPlay Customer Service to receive replacement instructions for any damaged items This may include returning the damaged part to FIG LLC for service Customer Service Toll Free 855 PWR PLAY 855 797 7529 Email info powerplay us FIG LLC Inc 1638 South Main Street Tulsa OK 74119 USA 12 period and the display will show during that time 6 Each individual port will automatically time out after 20 minutes When this happens
11. n any liquid for any reason e Clean the outer surface of the pump unit using a soft cloth moistened with soapy water or 70 isopropyl alcohol e Do notuse bleach on any item e Donotuse abrasive or volatile cleaners display or control panel could become scratched and hard to read e Do not place wrap in dryer as the bladder could melt e Hand wash exterior of wrap using a soft cloth moistened with soapy water or 70 isopropyl alcohol and let air dry Storage e Store in a dry location between 10 C 50 F and 40 C 104 F 30 75 relative humidity Do not expose to heat exceeding 65 C 149 F Do not store items in direct sunlight Roll wrap and do not fold as folding will decrease the life of your product Connect unit to charger for recharge no less than 2 hours every 60 days to preserve integrity of internal batteries 11 PROBLEM Air tube outlet connector will not fit in port SOLUTION Make sure the metal thumb latch is pressed until it clicks such that the two ends of the connectors will fit together Unit will not turn on Battery charge is too low Connect unit to a wall supply for a fresh charge and turn on Cannot feel pressure treatment area s e Wrap is not wrapped tightly enough e Air tubes are not connected e Bladder is damaged and will not hold air Replacement wraps are available by contacting customer service e Tube is damaged e Ensure that the wrap is connected to the pro
12. per outlet corresponding to the selected port Pressure on Auxiliary wrap is too high e Verify settings are correctly set to desired pressure e Decrease pressure setting e Loosen wrap HI alarm High pressure detected or set pressure detected too soon Remove any kinks from line Be sure the tubes are not tangled or constricted Start pump again by turning unit OFF and back to ON LO alarm Set pressure not detected within allotted time period Ensure tubing is properly connected wraps are attached to be snug and there are no air leaks Start pump again by turning unit OFF and back to ON BL alarm Pump will not operate Battery charge is low Connect charger BL alarm still occurs after battery charging Battery pack has expired 14 Contact PowerPlay at 855 PWR PLAY 855 797 7529 15 V7 02 04 14
13. ysician WARNING Ensure the pump control unit is turned off and unplugged from the wall outlet prior to and while cleaning or disinfecting WARNING Equipment should not be used in the presence of any FLAMMABLE ANESTHETIC MIXTURE WITH AIR OR WITH OXYGEN OR NITROUS OXIDE CAUTION Do not immerse in any liquid for any reason CAUTION Do not operate device in a wet environment CAUTION Do not subject the unit to extreme shocks such as dropping the pump unit CAUTION Contains no user serviceable parts CAUTION Do not place any items in an autoclave Pressure Display Set Pressure Button Port 2 Power l PORTI PORT2 ORT3 Set NES m re ne A Pressure ON OFF Atom Port 3 Set ae LOW BATT CHARGING Battery Port 1 PORTI PORT2 PORT3 Charging indicator Red Charging L Baden Green Charge Indicator Complete Selected Function JC POWERPLAY Indicators Battery Charger Input adi oe Port 1 Port 3 Connector Connector Port 2 Connector ITEMS INCLUDED BUT NOT SHOWN e Wall Plug Type Power Adaptor DC Connector mates with control unit charger VARIOUS EXTREMITY WRAPS MAY BE INCLUDED BUT NOT SHOWN Environmental Considerations e Do not operate pump below 0 C 32 F e Do not expose to heat exceeding 65 C 149 F e Do not operate the pump if it has been stored in freezing conditions Allow wraps to warm to room temperature if exposed to temperatures below 5 C 41
Download Pdf Manuals
Related Search