LPC2 CA1 User Manual
Contents
1. SMARTEH LIVING SYSTEMS USER MANUAL Longo programmable controller LPC 2 CA1 special module Version 2 SMARTEH doo Trg tigrovcev 1 5220 Tolmin Slovenia Tel 386 0 5 388 44 00 e mail info smarteh si www smarteh si Longo programmable controller LPC 2 CA1 special module SMARTrTEH LIVING SYSTEMS Written by SMARTEH d o o Copyright 2012 SMARTEH d o o User Manual Document Version 002 July 1 2012 e a Longo programmable controller LPC 2 CA1 special module SMARTEH LIVING SYSTEMS STANDARDS AND PROVISIONS Standards recommendations regulations and provisions of the country in which the devices will operate must be considered while planning and setting up electrical devices Work on 230 VAC network is allowed for authorized personnel only DANGER WARNINGS Devices or modules must be protected from moisture dirt and damage during transport storing and operation WARRANTY CONDITIONS For all modules LONGO LPC 2 if no modifications are performed upon and are correctly connected by authorized personnel in consideration of maximum allowed connecting power we offer warranty for 24 months from date of sale to end buyer In case of claims within warranty time which are based on material malfunctions the producer offers free replacement The method of return of malfunctioned module together with description can be arranged with our authorized representative War2. cance tucweeeesseeceues oq E a 3 Del PL AraMEelE EE 3 ZU INS TAU AO ME 4 4 1 Connection SCNEME ccceccecccnsccccceeccesceescesccesceeccesceeseecescesceees 4 4 2 Mounting frame selecton ccc ses 6 A NOURENS REENEN 7 4 4 Module e E ue E 9 5 TECHNICAL SPECIFICATIONS EN 10 G CHANGES EEN 11 NOTES a etten 12 jii e lt a Longo programmable controller LPC 2 CA1 special module SMARTEH LIVING SYSTEMS 1 DESCRIPTION LPC 2 CA1 RFID reader is intended to be used as an identity verification device at room entrance Module also provides display for four different messages and requests usually activated from other module inside the room This messages are convenient to notify personnel e g occupied do not disturb SOS room service When RFID tag key card is approached to the reader the green LED blinks and a short beep is generated if code is successfully read out In case key card for correspondent room is valid the green LED blinks again and a short beep is generated Other devices can be activated at this event like door lock opening turning light on LPC Manager can be used for function logic If the ID card number is not valid the red LED blinks and a longer beep is generated In case other magnet or contact chip card system is used for door unlock LPC 2 CA1 module can be used only to show messages LPC 2 CA1 module can be modified on customer request custom front label touch buttons added
3. LEDs added housing color Please contact manufacturer for more information Longo programmable controller LPC 2 CA1 special module SMARTER LIVING SYSTEMS 2 FEATURES DO NOT ROOM DISTURB SERVICE x vi sos OCCUPIED SMARTEH Figure 1 LPC 2 CA1 special module Table 1 Technical data RFID reader LEDs for showing activated messages amp requests occupied do not disturb room service SOS OK J LED FAULT X LED Power LED Internal fault LED Internal built in buzzer e a Longo programmable controller LPC 2 CA1 special module SMARTEH LIVING SYSTEMS 3 OPERATION Operation of the CA1 module is also dependent on parameters received on RS485 communication channel Reader RFID field is active always when module is powered up If tag is put inside RFID field reader tries to resolve RFID tag code If code is read successfully module activates status ilDNew generates a short beep OK LED1 blinks and code is transmitted in ilDW1 ilDW3 status fields In MCU application this code can be read out and authenticated If code has appropriate rights MCU should activate oOK command If code is not authorized MCU application should activate oFault command Regarding command received following action are triggered on module OOK gt OK LED4 blink short beep oFault gt FAULT LED3 blink long beep Either command is received or not from MCU application wi
4. Longo programmable controller LPC 2 CA1 special module SMARTEH LIVING SYSTEMS 4 INSTALLATION 4 1 Connection scheme Figure 2 Connection scheme Future use module DP1 CH1 CA1 S1 Table 2 K1 Longo programmable controller LPC 2 CA1 special module Ge SMARTTEH LIVING SYSTEMS K1 1 GND Ground K1 2 10 24 VDC Power supply input K1 3 RS485 A Data receive send line A K1 4 RS485 B Data receive send line B Table 3 LEDs amp Buttons On request active LED1 blue do not disturb Off no request LED2 blue room service on es a ne Off no request LED3 red FAULT X On RFID key standard NOK or ID card number wrong Off No tag in proximity LED4 green OK lt r On RFID key standard OK and ID card number valid Off No tag in proximity LEDS blue SOS On request active Off no request On request active LED6 blue occupied Off no request Se On RS485 communication fault KEES OURS Off RS485 communication OK LED8 green Power supply EE OF Off power supply missing or power off Table 4 S1 RS485 ADDRESS Switch 1 Switch 2 0 OFF OFF 1 OFF ON 2 ON OFF 3 ON ON e a Longo programmable controller LPC 2 CA1 special module SMARTER LIVING SYSTEMS 4 2 Mounting frame selection Frame suitable for CA1 module insertion should be modular one at least 3 gang wide Be careful to have correspondin
5. al 11 a Longo programmable controller LPC 2 CA1 special module SMARTER LIVING SYSTEMS 7 NOTES
6. ame 10 year of code opening V denotes flush frame mounting module 01 derivation code 001 version code reserved for future HW and or SW firmware upgrades D C 01 10 is the date code 01 week and 10 year of production S N CA1 S9 1000000003 is the serial number CA1 short product name S9 user code test procedure e g Smarteh person xxx 10 year last two cyphers 00000003 current stack number previous module would have the stack number 00000002 and the next one 00000004 a Longo programmable controller LPC 2 CA1 special module SMART EH LIVING SYSTEMS 5 TECHNICAL SPECIFICATIONS Table 6 Technical specifications Power supply from MCU Interconnection connector type RJ12 6 6 Power consumption 2W RFID type EM4100 125kHz Manchester 64 read only Max reading distance 4cm Dimensions W x H x D 75 x 49 x 29 mm Weight 40 g Ambient temperature 0 to 50 C Ambient humidity max 95 no condensation Maximum altitude 2000 m Mounting position horizontal Transport and storage temperature 20 to 60 C Protection class IP 20 10 _ a Longo programmable controller LPC 2 CA1 special module SMARTrTEH 3 LIVING SYSTEMS 6 CHANGES The following table describes all the changes to the document Date V Description 1 7 2012 002 CGP General update 1 1 2010 001 The initial version issued as LPC 2 CA1 module UserManu
7. d g Ti 7 e a Longo programmable controller LPC 2 CA1 special module SMARTER LIVING SYSTEMS 1 Set the correct RS485 address S1 switch for LPC 2 CA1 refer to the Table 4 Connect interconnection cable to the connector K1 Max allowed tractive force is 30 N Put the LPC 2 CA1 in mounting frames gt Cover LPC 2 CA1 with cover plate LPC 2 CA1 connects to the MCU unit on its RS485 port using interconnection cable When more special modules e g LPC 2 CR1 LPC 2 CH1 LPC 2 DP1 are connected to MCU splitter is also required e g SPL 2 Interconnection cable can be terminated on site considering wiring scheme bellow Cable AWG26 4C flat JL g Figure 5 Interconnection 6 mei cable ICM X Rj12 6pin M Rj12 6pin M plastic notch faced pin faced NOTE Signal wires must be installed separately from power and high voltage wires in accordance with general industry electrical installation standard a WT EN N K Bs geff mi e a Longo programmable controller LPC 2 CA1 special module SMARTEH LIVING SYSTEMS 4 4 Module labeling Table 5 Labels Label 1 Label 2 LPC 2 CA1 P N 225CA110V01001 S N CA1 S9 1000000003 D C 01 10 Label description LPC 2 CA1 is the full product name P N 225CA110V01001 is the part number 225 general code for LPC 2 product family CA1 short product n
8. g flush mounting box provided on the place where module will be positioned Smarteh has verified following lines to be compatible with LPC 2 CA1 module e Bticino Living Light e Gewiss Playbus System e Vimar Plana Idea e Tem Modul Soft Modul Line e Master Frames of other vendors most probably suits as well but they were not verified by Smarteh Before installation verify compatibility of non listed frames Module housing has a fin on each side which can be easily removed with knife cutter or pliers This adaptation enables housing to be build in various frame formats with two different depths With regard to frame used you may remove fin for housing to fit in gt N N Ds sn D Figure 3 Fin removing Longo programmable controller LPC 2 CA1 special module SMARTER LIVING SYSTEMS 4 3 Mounting instructions Figure 4 Housing dimensions e Dimensions in millimeters All connections module attachments and assembling must be done while A module is not connected to the main power supply Module should not be mounted outdoors Several RFID panels should not be mounted close to each other Minimum distance to next panel is at least 30 cm This restriction also applies in case of mounting panels on both sides of the same wall Adequate shielding material and provisions could be used to avoid interference between panels Mounting of RFID panels into conductive metal frames is not allowe
9. ranty does not include damage due to transport or because of unconsidered corresponding regulations of the country where the module is installed This device must be connected properly by the provided connection scheme in this manual Misconnections may result in device damage fire or personal injury Hazardous voltage in the device can cause electric shock and may result in personal injury or death NEVER SERVICE THIS PRODUCT YOURSELF This device must not be installed in the systems critical for life e g medical devices aircrafts etc If the device is used in a manner not specified by the manufacturer the degree of protection provided by the equipment may be impaired Waste electrical and electronic equipment WEEE must be collected separately LONGO LPC 2 complies to the following standards e EMC EN 61000 6 2 EN 50082 EN 61000 6 4 EN 50081 e LVD IEC 61131 2 e Vibrations and climatic mechanical EN 60068 2 6 EN 60068 2 27 EN 60068 2 29 X Pep Smarteh d o o operates a policy of continuous development Therefore we reserve the right to make changes and improvements to any of the products described in this manual without any prior notice MANUFACTURER SMARTEH d o o Trg tigrovcev 1 5220 Tolmin Slovenia Longo programmable controller LPC 2 CA1 special module SMARTrTEH LIVING SYSTEMS Index Longo programmable controller LPC 2 CA1 special module DESCRIPTION ee ae 1 EE 2 JOPERA TION
10. thin 10 seconds module clears ilDNew Status and waits for next RFID tag While CA1 module is waiting for authorization response new RFID tags can not be read 3 1 Parameters If parameter is set to logical 1 is considered to be active enabled or set If parameter has logical value 0 is considered to be inactive disabled or cleared Parameter can be status or command Parameter as status means that CA1 module is sending information to MCU On the other hand command represents request from MCU to module iComm Normal state is 0 If set there is communication error or no communication established ilDNew When new RFID tag is recognized this status is set active for 10sec or till authorization command is received oOK or oFault oBuzz While this command is active buzzer is active oOK Command for authorization of RFID code oFault Command for rejecting authorization of RFID code oOccup While this command is active occupied message LED6 is set oDNDist While this command is active do not disturb message LED1 is set oRServ While this command is active room service request LED2 is set oSOS While this command is active SOS request LED5 is set oOkLD While this command is active OK LED4 is set oFaultLD While this command is active fault LED3 is set iIDW1 Upper most significant third of RFID code iIDW2 Middle third of RFID code iIDW3 Lower least significant third of RFID code
Download Pdf Manuals
Related Search