ADJUSTABLE-HEIGHT WORKTABLE USER`S MANUAL Item
Contents
1. 3531 ADJUSTABLE HEIGHT WORKTABLE USER S MANUAL Fees Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating Failure to follow the safety rules and other basic safety precautions may result in serious personal injury Page 1 of 5 Thank you very much for choosing a Wel Bilt Product For future reference please complete the owner s record below Model Purchase Date Save the receipt warranty and these instructions It is important that you read the entire manual to become familiar with this product before using it This machine is designed for certain applications only The distributor strongly recommends that this machine is not modified and or used for any application other than that for which it was designed If you have any questions relative to a particular application DO NOT use the machine until you have first contacted the distributor to determine if it can or should be performed on the product For technical questions and replacement parts please call 1 800 222 5381 Specifications Tabletop Dimensions 20 1 8in W x 17 3 4in D x 3 4in thick Tabletop Material 3 4in pressboard Frame Material Formed and stamped sheet steel 30 1 4in maximum 1000 Ibs 1 1 1 Max Load Capacit 1000 Ibs SAVE THIS MANUAL You will need this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures parts list and assem2. ERATING INSTRUCTIONS 1 8 9 Assemble two legs 1 to one lower short beam 5 and two lower long beams 6 by bolt 13 washer 14 and nut 15 Put the table feet 10 on each of the table leg Assemble the short middle beam 3 and two long middle beams 4 to the legs just assembled Depending on the desired table height mount the height adjuster 2 on the outside of the legs using bolt 13 and washer 14 tighten tightly Assemble the other two legs with short middle beam 3 and short lower beam 5 Use bolt through the height adjuster screw through short lower beam and washer tighten securely Slide the middle table board 8 into the long middle beam 4 Slide the lower table board 9 into the long lower beam 6 Attach the leg subassembly done in step 4 to the extending long middle beam and the long lower beam Use bolt through the height adjuster screw through short lower beam and washer tighten securely Put the table top 7 upside down on the floor exposing the mounting holes Mount the connector 11 using screw 12 tighten securely 10 Place the completed frame assembly over the connector and screw tightly 11 Turn the completed worktable over so that it stands on its feet NOTE Do not expose worktable to rain or wet conditions Nwarning Maximum Weight Capacity 1000 Ibs load Do not exceed this maximum weight capacity Nwarning Only use normal sized table top equip
3. bly diagram Keep this manual and invoice in a safe and dry place for future reference WARNINGS amp PRECAUTIONS NwWarning Failure to follow these rules may result in serious personal injury 1 For your own safety read instruction manual before using the worktable Learn the application and limitation of the worktable Keep work area clean Cluttered areas invite injuries Dress properly Do not wear loose clothing or jewelry as they can be caught in moving parts Protective electrically non conductive clothes and non skid footwear are recommended when working Wear restrictive hair covering to contain long hair Do not overreach Keep proper footing and balance at all times Do not reach over or across running machines Check for damaged parts Before using this worktable any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment and binding of moving parts any broken parts or mounting fixtures and any other condition that may affect proper operation Any part that is damaged should be properly repaired or replaced Page 2 of 5 Unpacking When unpacking check to make sure that all the parts are included Refer to the Parts List and Assembly Drawing at the end of this manual If any parts are missing or broken please call the distributor at the number shown on the head page of this manual as soon as possible ASSEMBLY AND OP
4. ment on this worktable Oversized or overweight equipment can damage and possibly collapse the worktable Maintenance 1 Periodically check and tighten all screws and nuts on the worktable assembly 2 Store the worktable in a clean and dry location 3 When moving do not drag the worktable Lift and carry it Page 3 of 5 Parts List Part Part Description Quantity Leg 10 n 12 13 14 Nut 15 16 17 6 Diagram Page 4 of 5 WEL BILTs Distributed by Northern Tool Equipment Co Inc Burnsville MN 5337 0499 Made in China Page 5 of 5
Download Pdf Manuals
Related Search